SEARCH · Search NASA

Results for “Modulus”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

All sources NASA NTRS DOE OSTI

NASA NTRS2013

Predicting Bone Mechanical State During Recovery After Long-Duration Skeletal Unloading Using QCT and Finite Element Modeling

During long-duration missions at the International Space Station, astronauts experience weightlessness leading to skeletal unloading. Unloading causes a lack of a mechanical stimulus that triggers bone cellular units to remove mass from the skeleton. A mathematical system of the cellular dynamics predicts theoretical changes to volume fractions and ash fraction in response to temporal variations in skeletal loading. No current model uses image technology to gather information about a skeletal site s initial properties to calculate bone remodeling changes and then to compare predicted bone strengths with the initial strength. The goal of this study is to use quantitative computed tomography (QCT) in conjunction with a computational model of the bone remodeling process to establish initial bone properties to predict changes in bone mechanics during bone loss and recovery with finite element (FE) modeling. Input parameters for the remodeling model include bone volume fraction and ash fraction, which are both computed from the QCT images. A non-destructive approach to measure ash fraction is also derived. Voxel-based finite element models (FEM) created from QCTs provide initial evaluation of bone strength. Bone volume fraction and ash fraction outputs from the computational model predict changes to the elastic modulus of bone via a two-parameter equation. The modulus captures the effect of bone remodeling and functions as the key to evaluate of changes in strength. Application of this time-dependent modulus to FEMs and composite beam theory enables an assessment of bone mechanics during recovery. Prediction of bone strength is not only important for astronauts, but is also pertinent to millions of patients with osteoporosis and low bone density.

Chang, Katarina L.↗

NASA NTRS2013

Granular Media-Based Tunable Passive Vibration Suppressor

and vibration suppression device is composed of statically compressed chains of spherical particles. The device superimposes a combination of dissipative damping and dispersive effects. The dissipative damping resulting from the elastic wave attenuation properties of the bulk material selected for the granular media is independent of particle geometry and periodicity, and can be accordingly designed based on the dissipative (or viscoelastic) properties of the material. For instance, a viscoelastic polymer might be selected where broadband damping is desired. In contrast, the dispersive effects result from the periodic arrangement and geometry of particles composing a linear granular chain. A uniform (monatomic) chain of statically compressed spherical particles will have a low-pass filter effect, with a cutoff frequency tunable as a function of particle mass, elastic modulus, Poisson fs ratio, radius, and static compression. Elastic waves with frequency content above this cutoff frequency will exhibit an exponential decay in amplitude as a function of propagation distance. System design targeting a specific application is conducted using a combination of theoretical, computational, and experimental techniques to appropriately select the particle radii, material (and thus elastic modulus and Poisson fs ratio), and static compression to satisfy estimated requirements derived for shock and/or vibration protection needs under particular operational conditions. The selection of a chain of polymer spheres with an elastic modulus .3 provided the appropriate dispersive filtering effect for that exercise; however, different operational scenarios may require the use of other polymers, metals, ceramics, or a combination thereof, configured as an array of spherical particles. The device is a linear array of spherical particles compressed in a container with a mechanism for attachment to the shock and/or vibration source, and a mechanism for attachment to the article requiring isolation (Figure 1). This configuration is referred to as a single-axis vibration suppressor. This invention also includes further designs for the integration of the single-axis vibration suppressor into a six-degree-of-freedom hexapod "Stewart"mounting configuration (Figure 2). By integrating each singleaxis vibration suppressor into a hexapod formation, a payload will be protected in all six degrees of freedom from shock and/or vibration. Additionally, to further enable the application of this device to multiple operational scenarios, particularly in the case of high loads, the vibration suppressor devices can be used in parallel in any array configuration.

Dillon, Robert P.↗

NASA NTRS2013

Covalent Crosslinking of Carbon Nanotube Materials for Improved Tensile Strength

Carbon nanotubes have attracted much interest in recent years due to their exceptional mechanical properties. Currently, the tensile properties of bulk carbon nanotube-based materials (yarns, sheets, etc.) fall far short of those of the individual nanotube elements. The premature failure in these materials under tensile load has been attributed to inter-tube sliding, which requires far less force than that needed to fracture individual nanotubes.1,2 In order for nanotube materials to achieve their full potential, methods are needed to restrict this tube-tube shear and increase inter-tube forces.Our group is examining covalent crosslinking between the nanotubes as a means to increase the tensile properties of carbon nanotube materials. We are working with multi-walled carbon nanotube (MWCNT) sheet and yarn materials obtained from commercial sources. Several routes to functionalize the nanotubes have been examined including nitrene, aryl diazonium, and epoxide chemistries. The functional nanotubes were crosslinked through small molecule or polymeric bridges. Additionally, electron beam irradiation induced crosslinking of the non-functional and functional nanotube materials was conducted. For example, a nanotube sheet material containing approximately 3.5 mol amine functional groups exhibited a tensile strength of 75 MPa and a tensile modulus of 1.16 GPa, compared to 49 MPa and 0.57 GPa, respectively, for the as-received material. Electron beam irradiation (2.2x 1017 ecm2) of the same amine-functional sheet material further increased the tensile strength to 120 MPa and the modulus to 2.61 GPa. This represents approximately a 150 increase in tensile strength and a 360 increase in tensile modulus over the as-received material with only a 25 increase in material mass. Once we have optimized the nanotube crosslinking methods, the performance of these materials in polymer matrix composites will be evaluated.

polymer matrix composites↗

NASA NTRS2015

Nanotubular Toughening Inclusions

Conventional toughening agents are typically rubbery materials or small molecular weight molecules, which mostly sacrifice the intrinsic properties of a matrix such as modulus, strength, and thermal stability as side effects. On the other hand, high modulus inclusions tend to reinforce elastic modulus very efficiently, but not the strength very well. For example, mechanical reinforcement with inorganic inclusions often degrades the composite toughness, encountering a frequent catastrophic brittle failure triggered by minute chips and cracks. Thus, toughening generally conflicts with mechanical reinforcement. Carbon nanotubes have been used as efficient reinforcing agents in various applications due to their combination of extraordinary mechanical, electrical, and thermal properties. Moreover, nanotubes can elongate more than 20% without yielding or breaking, and absorb significant amounts of energy during deformation, which enables them to also be an efficient toughening agent, as well as excellent reinforcing inclusion. Accordingly, an improved toughening method is provided by incorporating nanotubular inclusions into a host matrix, such as thermoset and thermoplastic polymers or ceramics without detrimental effects on the matrix's intrinsic physical properties.

Park, Cheol↗

NASA NTRS2017

Nanotubular Toughening Inclusions

Park, Cheol↗

NASA NTRS2017

Meteorite Material Model for Structural Properties

To assess the threat posed by an asteroid entering Earth's atmosphere, one must predict if, when, and how it fragments during entry. A comprehensive understanding of the asteroid material properties is needed to achieve this objective. At present, the meteorite material found on earth are the only objects from an entering asteroid that can be used as representative material and be tested inside a laboratory setting. Due to complex petrology, it is technically challenging and expensive to obtain reliable material properties by means of laboratory test for a family of meteorites. In order to circumvent this challenge, meteorite unit models are developed to determine the effective material properties including Youngs modulus, compressive and tensile strengths and Poissons ratio, that in turn would help deduce the properties of asteroids. The meteorite unit is a representative volume that accounts for diverse minerals, porosity, cracks and matrix composition. The Youngs Modulus and Poissons Ratio in the meteorite units are calculated by performing several hundreds of Monte-Carlo simulations by randomly distributing the various phases inside these units. Once these values are obtained, cracks are introduced in these meteorite units. The size, orientation and distribution of cracks are derived by extensive CT-scans and visual scans of various meteorites from the same family. Subsequently, simulations are performed to attain stress-strain relations, strength and effective modulus values in the presence of these cracks. The meteorite unit models are presented for H, L and LL ordinary chondrites, as well as for terrestrial basalt. In the case of the latter, data from the simulations is compared with experimental data to validate the methodology. These material models will be subsequently used in fragmentation modeling of full scale asteroids.

Meteorite↗

NASA NTRS2019

Quantifying the Influence of Redox Conditions on the Seismic Properties of Olivine

A series of eight olivine specimens were fabricated by hot-pressing at 1200 degrees Celsius and 300 megapascals (MPa). Each hot-pressed specimen was then wrapped in Pt, Ni or NiFe foil to vary oxygen fugacity (fO2), and interrogated via forced torsional oscillation. Mechanical testing was conducted at 10 oscillation periods between 1 and 1000 seconds, at a confining pressure of 200 MPa, during a slow staged-cooling from a maximum temperature of 1200 degrees Celsius to room temperature. After mechanical testing, each specimen was axially sectioned and EBSD (Electron BackScatter Diffraction) was used for the determination of the representative grain size, and grain size distribution of each sample. In addition, each longitudinal section was mapped via FTIR (Fourier Transform InfraRed spectroscopy) to determine the spatial distribution and concentrations of chemically bound and molecular water. Amongst these specimens, chemically bound ‘water’ contents were observed to vary between 0 and 1150 atom ppm (parts per million) H/Si, and molecular water concentrations varied between 0 and 245 atom ppm H/Si. Our forced-oscillation results demonstrate that the measured magnitude of anelastic relaxation within the experimental ‘window’ of oscillation periods is unrelated to the water content. Rather, a relationship was observed between the magnitude of anelastic relaxation and the prevailing redox conditions, which is influenced by the choice of metal sleeving used during the mechanical test. Further, regardless of water content or metal sleeving, each specimen exhibits coupled variations in shear modulus and dissipation within the observational window, indicative of ‘high-temperature background’ behavior, that can be described by a Burgers-type model. During initial fitting of the Burgers models, the unrelaxed shear modulus at a reference temperature of 900 degrees Celsius (G (sub UR)) and the temperature derivative of the unrelaxed shear modulus (dG (sub U)/dT), were treated as adjustable parameters. For all Fe-bearing olivine samples (but not a hydrous and oxidized Fe-free sample) we observe deficits of G (sub UR), and increased values of dG (sub U)/dT, relative to the expected elastic (anharmonic) behavior of Fo90 olivine. This behavior is indicative of anelastic relaxation occurring at shorter periods than observable within the ‘window’ of oscillation periods used in the mechanical test. Moving towards a comprehensive seismologically applicable Burgers model, which includes this newly observed effect of redox conditions on anelastic relaxation, we will present our progress in reconciling truly anharmonic and elastic behavior of Fo (sub 90) olivine with our observed forced-oscillation data.

Cline, Christopher, II↗

NASA NTRSDate not supplied

Electrostrictive Graft-Elastomers (G-Elastomers) - Materials, Devices and Applications - A Review

Electroactive polymers, especially electromechanically active polymers, have drawn extensive attention worldwide since the piezoelectricity and ferroelectricity of poly (vinylidene fluoride) (PVDF) was discovered in 1969. In the past three decades, several new classes of electroactive polymers that demonstrate promising electromechanical properties have been developed. Electrostrictive Graft Elastomers (G-elastomer) developed at NASA Langley Research Center have been recognized as one of the more promising electroactive polymers due to their large electric field-induced strain (~4%) and high mechanical modulus (~700 MPa). Electromechanical performance of the G-elastomer is a promising class of electroactive polymer materials because it exhibits a novel molecular mechanism that allows enhancement in the field induced strain and in the mechanical modulus synergistically. The combination of large induced strain and high mechanical modulus allows the electrostrictive graft elastomer to offer very promising electromechanical properties, in terms of output mechanical energy density, making it plausible as a candidate for use in high performance and low mass actuation devices in various aerospace applications. In this presentation, the molecular structures, properties, processing and mechanisms of the electromechanical performance, as well as its applications in actuation devices for advanced aerospace technologies, will be comprehensively reviewed and discussed.

Polymer↗

NASA NTRS2020

An inflationary probe of cosmic Higgs switching

A scalar Higgs field can be repeatedly switched on and off when it couples to a classically oscillating scalar modulus field. The modulus flips the Higgs mass term between stable and tachyonic values. We study a cosmological scenario in which such repeated phase transitions occur during inflation. An irrelevant operator coupling the Higgs field to the inflaton can then imprint the pattern of phase transitions in the correlation functions of the inflaton. Using both numerical and analytic studies, we show that the inflaton 2-point function carries characteristic imprints of the modulus oscillation and its effect on the Higgs boson. We briefly remark on the potential observability of such patterns and how they might be distinguished from other dynamics in the early universe.

JiJi Fan↗

NASA NTRS2024

What is “First Ply Failure” in a Unidirectionally Loaded Quasi-Isotropic Composite (and does it exist)?

This study presents experimental results of unidirectional tension tests on quasi-isotropic laminates to observe so called “first ply failure” (FPF). The modulus of the laminates was measured throughout the test to observe any ply degradation. Quasi-isotropic (QI) laminates were tested since this is the most common layup sequence of a laminate in industry and FPF, if it exists to any practical extent, should be observed. The authors are unaware of any claim that only bi-axial loads are needed to cause FPF, thus uniaxial testing was performed since this is much simpler than bi-axial testing. Laminates can be engineered to cause anomalies (“knees” or abrupt change in modulus) in a stress-strain curve (such as sandwiching multiple 90° plies between a couple of 0° plies) but such laminates should never be used in practice. The search for FPF was examined in simple 8 ply QI laminates by stopping tension tests at various levels post predicted FPF and examining the specimen for “ply failure” and ascertaining its effect (if any) on the modulus of the laminate. The ultimate strength values were found for some specimens. Results showed that for 8 ply QI laminates, no FPF of note was found and challenges the whole notion of FPF and thus “progressive failure”.

First ply failure↗

NASA NTRS2024

Scalability in SLA lattice through lattice orientation and hybrid frame and plate architectures

Lightweighting has been a key goal for engineers and designers, with lattice structures widely explored as the building blocks for structural components. Cellular structure-inspired lattice truss frame designs made of struts, have been extensively studied. All plate-based lattice designs have superior mechanical performance. Limits in scalability occur from formation of closed pockets limiting uv curing in processes like stereolithography (SLA). We examine hybrid frame and plate body-centered cubic-simply cubic (BCC-SC) lattices under compression. Unit cells and scaled up lattice exhibit an increase in yield stress and modulus with the addition of plates. The loading direction on the hybrid frame and plate unit cells affected the magnitude of improvement. Simulations and measurements indicated that the optimal lightweight lattice was determined to be when two plates were placed opposite each other with plates buttressing the struts, inhibiting buckling of the struts aligned with the loading direction. This lattice resulted in 63% improvement in specific modulus, a 137% improvement in specific yield point, and a 360% improvement in specific energy absorption (SEA) and the scaled up 4 × 4 × 4 scaled-up structures, showed a 107%, 148%, and 297% in specific modulus, specific yield point, and SEA, respectively A combined stretching-bending behavior was identified in optimal orientations reflecting the delayed buckling mechanism paired to a rising stress-strain curve past the elastic yield indicating bending resistance. The mass moment of inertia was found to be a key parameter correlating optimum orientation for the same number of plates added to the BCC-SC frame.

Mahan Ghosh↗

NASA NTRS2026

Influence of Processing Parameters on the Mechanical Properties of 3D Printed Borosilicate Particulate Reinforced Polymer Composites

Emerging composite materials are expanding the potential of additive manufacturing and enabling applications previously restricted by traditional manufacturing methods. The multi-phase nature of these composite materials combined with the complex in-ternal geometry of additively manufactured parts have enabled unique behavior, and potentially new applications. Additionally, these materials can be pyrolyzed to create dense metal, ceramic, and glass parts with geometries typically not achievable by tra-ditional processes. Additive manufacturing of borosilicate glass-based systems can open new applications in nuclear engineering, astronomy, and bone regrowth therapy. To elucidate the process-parameter relationship of borosilicate-polylactic acid (PLA) composites, mechanical testing was conducted and compared with a pure polylactic acid polymer baseline. Test specimens were fabricated by fused-filament fabrication with minimal post-processing. Yield strength, ultimate strength, and elastic modulus were calculated from stress-strain curves. Optical and scanning electron microscopy were conducted to observe the specimen microstructure before and after testing. The highest compressive yield strength for the composite was 28.22 MPa, and the highest compressive yield strength for PLA was 49.30 MPa. Print orientation was found to benefit the composite material but have a detrimental effect on the pure matrix material. An elastic modulus of 2.66 GPa was recorded for the borosilicate-PLA composite at 100% infill, 1 shell wall, and layer lines parallel to compression axis. Microscopy revealed that lower modulus composite specimens had the particulates re-distributed within the matrix. Tensile testing was done according to a polymer testing standard, which caused difficulties obtaining consistent fracture within the gauge length.

mechanical testing↗

DOE OSTI2024

AGC-4 Specimen Post-Irradiation Examination Data Interim Report

This interim report documents preliminary results of the post-irradiation examination material property testing from the fourth advanced graphite creep (AGC), AGC 4, capsule specimens. This is the fourth of a series of six irradiation test trains planned as part of the AGC experiment to fully characterize the neutron irradiation effects and radiation creep behavior of current nuclear graphite grades to moderate dose levels (=7 dpa). The AGC 4 capsule was irradiated in the Idaho National Laboratory Advanced Test Reactor at a nominal temperature of 800°C and to a peak dose of 8 dpa. Half of the AGC-4 specimens were subjected to compressive stresses to induce irradiation creep. Post-irradiation testing and measurement results are reported with the exception of thermal testing, which is still in progress, and irradiation mechanical strength testing. Additionally, some specimens initially deemed too hot to be examined in the ART Graphite laboratory may still be measured. The data reported includes specimen dimensions for both stressed and unstressed specimens to establish the irradiation creep rates, mass and dimensional data necessary to derive density, elastic constants (Young?s modulus, shear modulus, and Poisson?s ratio) from ultrasonic time of flight velocity measurements, Young?s modulus from the fundamental frequency of vibration, and electrical resistivity. A more complete evaluation of trends in the material property changes, as well as irradiation-induced creep due to the irradiation environment and applied load on the specimens, will be discussed later in AGC 4 post-irradiation examination analysis reports.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2024

Physical Properties of Hilti HIT-RE 500 V3 After Irradiation: Slant Shear, Tensile, Flexural, and Compressive

There are various applications in which epoxy adhesives may be used within hot-cell environments. These epoxies currently see limited use within hot cells since it is known that organics see degradation after small doses even as low as 50 kilogray (kGy). These losses in physical property strengths limit the use of these epoxies to non-structural applications. In modern construction, however, the use of epoxies to bond structural components such as rebar or threaded anchors is becoming increasingly prevalent. To employ these types of materials the Idaho National Laboratory (INL) has begun investigating the specific degradation properties of epoxies for use in structural applications in environments where radiation is present. Hilti HIT-RE 500 V3 is used extensively in new construction and renovation projects across the world. The INL has conducted various tests on this epoxy for low dose environments. These tests include tensile, flexural, compression, and slant shear tests following the American Society for Testing Material International (ASTM) standards D638, D790, D695, and C882/882M respectively. Two sample sets for each test were created where the baseline specimens were not irradiated, and another set was irradiated to an accumulated dose of approximately 50-60 kGy. All the samples were destructively tested and analyzed focusing on the change in physical properties, examples of these tests are shown in Figures 1-4. Tensile testing results indicate a 0.9% loss in maximum load capacity, a 0.5% loss in tensile stress at maximum load, a 1.4% loss in tensile strain at break, and a 15% decrease in modulus of elasticity. Flexural testing results display an increase in all the following: 12% in strain at maximum load, 10% in maximum load capacity, 5% in stress at maximum load, and 3% in young’s modulus. The compressive physical properties after irradiation display a 1% increase in maximum load, a 3% decrease in stress at yield, and a 5% decrease in modulus of elasticity. The maximum compressive stress saw no measurable change after irradiation. The slant shear specimens after irradiation displayed a 2% increase in maximum load capacity and maximum compressive stress. Though a structural analysis would have to be completed as is normal for building design the increases and decreases in the measured physical properties indicate that this material may be used for structural applications in low dose hot-cell environments without adhesive failure.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Design and Development of Novel Equiatomic Refractory Multi Principal elemental Alloys Based on MoNbTi System for Use in Irradiation Environments

Multi Principal Elemental Alloys (MPEA) have emerged as promising materials for next-generation nuclear reactors due to their exceptional irradiation resistance. Eight equiatomic MPEA based on the MoNbTi system, comprising of elements with low thermal neutron absorption cross-sections were explored using a combined approach employing empirical parameter estimations, and CALPHAD simulations by which the phases and elemental segregation observed in all the alloys in the as-cast state were predicted. Solution heat treatment at 1500°C transformed five alloys into single-phase matrix materials, enhancing homogeneity and reducing hardness. The densities of the alloys ranged between 6.47 to 7.68 g/cm3, hardness between 472 and 656 VHN, Young’s modulus between 142 GPa to 169 GPa, shear modulus between 54 GPa and 62 GPa, bulk modulus between 117 GPa to 194 GPa and Poisson’s ratio between 0.3 to 0.35. The in-situ high temperature Xray diffraction results, differential scanning calorimetry and dilatometry results up to 1000°C suggested the high temperature phase stability of the MPEA. Subsequent ageing heat treatment at 800 and 1000 oC for 96 hours revealed significant secondary phase precipitation in MoNbTiZr, MoNbTiZrV, and MoNbTiCrA. Oxidation studies at 800 oC for 24 hours in air revealed superior oxidation resistance and cubic rate law dependence in Cr containing MPEA especially in MoNbTiCrAl, while severe mass gain resulting in total disintegration and exfoliation in MoNbTiZr and MoNbTiZrV. This comprehensive study underscores the potential of novel MPEA as promising materials for advanced nuclear reactor applications, shedding light on their microstructural control, mechanical properties, thermal stability, and oxidation resistance.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2024

Effects of irradiation damage on the elastic properties and hardness of complex transition metal diborides

Multi-principal component transition metal (TM) diborides represent a class of high-entropy ceramics (HECs) that have received considerable interest in recent years owing to their promising properties for extreme environment applications that include thermal/ environmental barriers, hypersonic vehicles, turbine engines, and next-generation nuclear reactors. While the addition of chemical disorder through the random distribution of TM elements on the cation sublattice has offered opportunities to tailor elastic stiffness and hardness, the effects of irradiationinduced structural damage on the physical properties of these complex materials have remained largely unexplored. To this end, changes in the hardness and elastic moduli of a high-entropy TM diboride (Hf0.2Nb0.2Ta0.2Ti0.2Zr0.2)B2 and three of its quaternary subsets following irradiation with 10 MeV gold (Au) ions to fluences of up to 6 × 10^15 Au cm-2 are investigated at the micrometer and sub-micrometer length-scales via the dispersion of laser-generated surface acoustic waves (SAW) and nanoindentation, respectively. The nanoindentation measurements show that the TM diborides exhibit an initial increase in hardness following irradiation with energetic Au ions, with a subsequent decrease in hardness following further irradiation. One quaternary composition, (Hf1/3Ta1/3Ti1/3)B2, exhibits a notable exception to the trend and continues to exhibit an increase in hardness with ion irradiation fluence. Although differences in the absolute values of the effective elastic moduli obtained from the measured SAW dispersion and nanoindentation are observed (and attributed to microstructural variations at the measurement length-scale), both techniques yield similar trends in the form of an initial reduction and subsequent saturation in the elastic modulus with increasing ion irradiation fluence. The quaternary TM diboride (Hf1/3Ta1/3Ti1/3)B2 again exhibits a departure from this trend. The high-entropy TM diboride (Hf0.2Nb0.2Ta0.2Ti0.2Zr0.2)B2 exhibits the greatest recovery in hardness and modulus when irradiated to high ion fluences following initial changes at low fluence, indicating superior resistance to radiation-induced damage over its quaternary counterparts. Opportunities for designing HECs with superior hardness and modulus for enhanced radiation resistance (compared to their single constituent counterparts) by tailoring chemical disorder and bond character in the lattice are discussed.

36 - MATERIALS SCIENCE↗

DOE OSTI2025

AGC-4 Specimen Post-Irradiation Examination Data Interim Report

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2024

Exploring biofiber properties and their influence on biocomposite tensile properties

Biofibers serve as effective reinforcements for neat polylactic acid (PLA) in biocomposites, offering an attractive opportunity to decarbonize the manufacturing sector of the United States by displacing fossil-based reinforcement fibers such as carbon fibers. Also, biofiber production can stimulate economic growth in rural economies, fueling sustainable development. PLA resins are commonly compounded with biofibers to create biocomposites suitable for additive manufacturing. PLA-biofiber composites often exhibit better overall material properties than neat (pure) PLA, but the associations between biofiber properties and the material properties of their biocomposites remain largely unexplored. Hence, this research delves into a comprehensive exploration of diverse biofibers, scrutinizing their physical and chemical attributes, including size, shape, ash content and biochemical composition. The study meticulously analyzes the flow properties of each biofiber and elucidates the ultimate tensile strengths and Young's modulus of corresponding biocomposite samples. Noteworthy correlations between biofiber and biocomposite tensile properties are uncovered, shedding light on critical interrelationships. The study introduces an approach employing regression models to predict the ultimate tensile strength and Young's modulus of biocomposites. These models, validated with a cross-validation technique, exhibit remarkable predictive accuracy, particularly in estimating ultimate tensile strength. © 2024 Oak Ridge National Laboratory managed by UT-Battelle, LLC and The Author(s). Polymer International published by John Wiley & Sons Ltd on behalf of Society of Chemical Industry.

36 MATERIALS SCIENCE↗