SEARCH · Search NASA

Results for “Nonlinear approximation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

All sources NASA NTRS DOE OSTI

NASA NTRS1999

An O(Nm(sup 2)) Plane Solver for the Compressible Navier-Stokes Equations

A hierarchical multigrid algorithm for efficient steady solutions to the two-dimensional compressible Navier-Stokes equations is developed and demonstrated. The algorithm applies multigrid in two ways: a Full Approximation Scheme (FAS) for a nonlinear residual equation and a Correction Scheme (CS) for a linearized defect correction implicit equation. Multigrid analyses which include the effect of boundary conditions in one direction are used to estimate the convergence rate of the algorithm for a model convection equation. Three alternating-line- implicit algorithms are compared in terms of efficiency. The analyses indicate that full multigrid efficiency is not attained in the general case; the number of cycles to attain convergence is dependent on the mesh density for high-frequency cross-stream variations. However, the dependence is reasonably small and fast convergence is eventually attained for any given frequency with either the FAS or the CS scheme alone. The paper summarizes numerical computations for which convergence has been attained to within truncation error in a few multigrid cycles for both inviscid and viscous ow simulations on highly stretched meshes.

Thomas, J. L.↗

NASA NTRS1983

Nonlinear effect on modal data analysis method

How the presence of nonlinearities in structural test data can be detected when using modern linear modal data analysis methods is discussed. The extent to which linear algorithms can provide useful information on nonlinear systems was discussed. The modal data analysis method successfully identified the frequency components (but not damping) of the true solution of a nonlinear systems. It was found that the approximate modal parameters of the linear system can be identified by the modal method when low levels of nonlinearities are present. The modal method successfully identified the modal parameters of a linear mode in the presence of a nonlinear response.

Horta, L. G.↗

NASA NTRSDate not supplied

Path Planning: Differential Dynamic Programming and Model Predictive Path Integral Control on VTOL Aircraft

This paper explores two optimal control approaches, widely used in robotics, to establish their viability as real-time trajectory planners for vehicle configurations envisioned for the emerging aviation sector of Urban Air Mobility (UAM). Differential Dynamic Programming (DDP) enables planning over highly nonlinear dynamics using second-order approximations along a nominal trajectory, and displays quadratic convergence to a local solution. Model Predictive Path Integral (MPPI) is a stochastic sampling-based algorithm that can optimize for general cost criteria, including potentially highly nonlinear formulations, and supports parallel computation through the use of modern GPU hardware. In this work, DDP and MPPI were implemented using model predictive control (MPC), and the results indicate they are able to successfully transition the aircraft over different flight envelopes and generate trajectories unique to UAM vehicles.

Differential Dynamic Programming↗

NASA NTRS1983

Microscopic Lagrangian description of warm plasmas. IV - Macroscopic approximation

The averaged-Lagrangian method is applied to linear wave propagation and nonlinear three-wave interaction in a warm magnetoplasma, in the macroscopic approximation. The microscopic Lagrangian treated by Kim and Crawford (1977) and by Galloway and Crawford (1977) is first expanded to third order in perturbation. Velocity integration is then carried out, before applying Hamilton's principle to obtain a general description of wave propagation and coupling. The results are specialized to the case of interaction between two electron plasma waves and an Alfven wave. The method is shown to be more powerful than the alternative possibility of working from the beginning with a macroscopic Lagrangian density.

Kim, H.↗

NASA NTRS1985

Nonlinear Dynamics of a Helicopter Model in Ground Resonance

An approximate theoretical method is presented which determined the limit cycle behavior of a helicopter model which has one or two nonlinear dampers. The relationship during unstable ground resonance oscillations between lagging motion of the blades and fuselage motion is discussed. An experiment was carried out on using a helicopter scale model. The experimental results agree with those of the theoretical analysis.

Tang, D. M.↗

NASA NTRS1986

Output time response approximation

The approximation of the output response of a nonlinear system by the output response of a linear system to a desired order irrespective of the admissible input applied should prove useful for purposes of control generation and simulation. Given a nonlinear system, an integer k, and an open subset of state space, sufficient conditions are stated that such a linear approximation exists to order k for every point in the set. In addition, a method for finding the approximating linear systems is presented.

Hunt, L. R.↗

NASA NTRS1977

Temperature, density, and composition in the disturbed thermosphere from Esro 4 gas analyzer measurements - A global model

An analysis of density measurements of Ar, N2, O, and He made at 280 km with the gas analyzer aboard the polar-orbiting satellite Esro 4 has yielded a global model of the variations in temperature, density, and composition that occur in the disturbed thermosphere. In the model the increase of temperature over quiet conditions is a nonlinear function of the planetary geomagnetic index, its latitude profile being approximated by a fourth-power sin phi law, where phi is the 'invariant' magnetic latitude. A density wave proceeding from high latitudes is approximated by a fourth power cos phi law. A strong nonlinearity in the relation between the temperature variations and the variations in the height of the homopause explains a previously found behavioral difference in the variation of atomic oxygen during magnetic storms and during periods of sustained geomagnetic activity.

Jacchia, L. G.↗

NASA NTRS1993

FD-TD modeling of 2-D dielectric waveguides for propagation and scattering of femtosecond optical solitons

Experimentalists have produced all-optical switches capable of 100-fs responses. To adequately model such switches, nonlinear effects in optical materials (both instantaneous and dispersive) must be included. In principle, the behavior of electromagnetic fields in nonlinear dielectrics can be determined by solving Maxwell's equations subject to the assumption that the electric polarization has a nonlinear relation to the electric field. However, until our previous work, the resulting nonlinear Maxwell's equations have not been solved directly. Rather, approximations have been made that result in a class of generalized nonlinear Schrodinger equations (GNLSE) that solve only for the envelope of the optical pulses. In this paper, we present first-time calculations from the vector nonlinear Maxwell's equations of femtosecond soliton propagation and scattering, including carrier waves, in two-dimensional systems of dielectric waveguides exhibiting the Kerr and Raman quantum effects. We use the finite-difference time-domain (FD-TD) method in an extension of our 1-D work. There, in a fundamental innovation, we treated the linear and nonlinear convolutions for the electric polarization as new dependent variables. By differentiating these convolutions in the time domain, we derived an equivalent system of coupled, nonlinear second-order ODE's. These equations together with Maxwell's equations form the system that is solved to determine the electromagnetic fields in inhomogeneous nonlinear dispersive media. Backstorage in time is limited to only that needed by the time-integration algorithm for the ODE's, rather than that needed to store the time-history of the kernel functions of the convolutions (1000-10,000 time steps). Thus, a 2-D nonlinear optics model from Maxwell's equations is now feasible.

Joseph, Rose↗

NASA NTRS1990

Formulation and validation of high-order linearized models of helicopter flight mechanics

A high-order linearized model of helicopter flight dynamics is extracted from a nonlinear time domain simulation. The model has 29 states that describe the fuselage rigid body degrees of freedom, the flap and lag dynamics in a nonrotating coordinate system, the inflow dynamics, the delayed entry of the horizontal tail into the main rotor wake, and, approximately, the blade torsion dynamics. The nonlinear simulation is obtained by extensively modifying the GENHEL computer program. The results indicate that the agreement between the linearized and the nonlinear model is good for small perturbations, and deteriorates for large amplitude maneuvers.

Kim, Frederick D.↗

NASA NTRS1991

An improved error analysis of finite element solutions for postbuckled plates

The accurate calculation of stresses at boundaries and interfaces where FEM analysis may be unreliable is presently undertaken by an error analysis that derives a continuous approximation to discrete finite-element data, which can be differentiated to compute continuous stresses for component-failure predictions. An evaluation is conducted of this approximation in the context of the nonlinear PDEs. A novel interpolation formula which is a simple modification of the double Fourier sine series is used to reduce truncation errors near the rectangular plate boundary by means of an 'extended grid'. Results are presented from a FEM solution, a conventional double-Fourier series' continuous approximation, and a solution applying interpolation on the extended grid, which yields superior convergence properties near the plate boundaries.

Sistla, Rajaram↗

NASA NTRS1991

Optimization of transistor design including large signal device/circuit interactions at extremely high frequencies (20-100+GHz)

Transistor design for extremely high frequency applications requires consideration of the interaction between the device and the circuit to which it is connected. Traditional analytical transistor models are to approximate at some of these frequencies and may not account for variations of dopants and semiconductor materials (especially some of the newer materials) within the device. Physically based models of device performance are required. These are based on coupled systems of partial differential equations and typically require 20 minutes of Cray computer time for a single AC operating point. A technique is presented to extract parameters from a few partial differential equation solutions for the device to create a nonlinear equivalent circuit model which runs in approximately 1 second of personal computer time. This nonlinear equivalent circuit model accurately replicates the contact current properties of the device as computed by the partial differential solver on which it is based. Using the nonlinear equivalent circuit model of the device, optimization of systems design can be performed based on device/circuit interactions.

Levy, Ralph↗

NASA NTRS2005

New Algorithms for Estimating Spacecraft Position Using Scanning Techniques for Deep Space Network Antennas

As more and more nonlinear estimation techniques become available, our interest is in finding out what performance improvement, if any, they can provide for practical nonlinear problems that have been traditionally solved using linear methods. In this paper we examine the problem of estimating spacecraft position using conical scan (conscan) for NASA's Deep Space Network antennas. We show that for additive disturbances on antenna power measurement, the problem can be transformed into a linear one, and we present a general solution to this problem, with the least square solution reported in literature as a special case. We also show that for additive disturbances on antenna position, the problem is a truly nonlinear one, and we present two approximate solutions based on linearization and Unscented Transformation respectively, and one 'exact' solution based on Markov Chain Monte Carlo (MCMC) method. Simulations show that, with the amount of data collected in practice, linear methods perform almost the same as MCMC methods. It is only when we artificially reduce the amount of collected data and increase the level of noise that nonlinear methods show significantly better accuracy than that achieved by linear methods, at the expense of more computation.

Metropolis-Hastings (MH)↗

NASA NTRS1998

Neural Network and Regression Approximations in High Speed Civil Transport Aircraft Design Optimization

Nonlinear mathematical-programming-based design optimization can be an elegant method. However, the calculations required to generate the merit function, constraints, and their gradients, which are frequently required, can make the process computational intensive. The computational burden can be greatly reduced by using approximating analyzers derived from an original analyzer utilizing neural networks and linear regression methods. The experience gained from using both of these approximation methods in the design optimization of a high speed civil transport aircraft is the subject of this paper. The Langley Research Center's Flight Optimization System was selected for the aircraft analysis. This software was exercised to generate a set of training data with which a neural network and a regression method were trained, thereby producing the two approximating analyzers. The derived analyzers were coupled to the Lewis Research Center's CometBoards test bed to provide the optimization capability. With the combined software, both approximation methods were examined for use in aircraft design optimization, and both performed satisfactorily. The CPU time for solution of the problem, which had been measured in hours, was reduced to minutes with the neural network approximation and to seconds with the regression method. Instability encountered in the aircraft analysis software at certain design points was also eliminated. On the other hand, there were costs and difficulties associated with training the approximating analyzers. The CPU time required to generate the input-output pairs and to train the approximating analyzers was seven times that required for solution of the problem.

Patniak, Surya N.↗

NASA NTRS1973

Noniterative estimation of a nonlinear parameter

An algorithm is described which solves the parameters X = (x1,x2,...,xm) and p in an approximation problem Ax nearly equal to y(p), where the parameter p occurs nonlinearly in y. Instead of linearization methods, which require an approximate value of p to be supplied as a priori information, and which may lead to the finding of local minima, the proposed algorithm finds the global minimum by permitting the use of series expansions of arbitrary order, exploiting an a priori knowledge that the addition of a particular function, corresponding to a new column in A, will not improve the goodness of the approximation.

Bergstroem, A.↗

NASA NTRS1990

Linear iterative solvers for implicit ODE methods

The numerical solution of stiff initial value problems, which lead to the problem of solving large systems of mildly nonlinear equations are considered. For many problems derived from engineering and science, a solution is possible only with methods derived from iterative linear equation solvers. A common approach to solving the nonlinear equations is to employ an approximate solution obtained from an explicit method. The error is examined to determine how it is distributed among the stiff and non-stiff components, which bears on the choice of an iterative method. The conclusion is that error is (roughly) uniformly distributed, a fact that suggests the Chebyshev method (and the accompanying Manteuffel adaptive parameter algorithm). This method is described, also commenting on Richardson's method and its advantages for large problems. Richardson's method and the Chebyshev method with the Mantueffel algorithm are applied to the solution of the nonlinear equations by Newton's method.

Saylor, Paul E.↗

NASA NTRSDate not supplied

Sonic Boom Propagation Model Based on a Single-Ray Jacobian

A sonic boom is a nonlinear event whose propagation can be modeled involving two stages. The first stage consists of ray path calculations using linear approximations, while the second stage deals with a nonlinear transport of the acoustic energy along these paths. This presentation discusses a second-order finite difference numerical approach used to predict the ray paths in range-dependent atmospheres and compares it to existing finite difference schemes. The approach is validated using exact solutions obtained for stratified atmospheres. In the second stage, the geometrical spreading effect needed in determining sonic boom waveforms from a Burgers' equation is obtained using a method that only needs a single ray rather than four rays required by most existing sonic boom propagation codes. The single-ray method calculates the Jacobian, associated with the coordinate transformation from a suitable ray coordinate system to the Cartesian coordinate system, directly from the ray tracing equations. While the four-ray method approximates the geometrical spreading using a finite difference scheme involving the four rays, the single-ray method does not rely on this approximation and instead depends purely on the acoustical kinematic properties of the atmosphere. Comparisons of results using these two methods are discussed.

sonic boom↗

NASA NTRS1976

Nonlinear Curvature Expressions for Combined Flapwise Bending, Chordwise Bending, Torsion and Extension of Twisted Rotor Blades

The nonlinear curvature expressions for a twisted rotor blade or a beam undergoing transverse bending in two planes, torsion, and extension were developed. The curvature expressions were obtained using simple geometric considerations. The expressions were first developed in a general manner using the geometrical nonlinear theory of elasticity. These general nonlinear expressions were then systematically reduced to four levels of approximation by imposing various simplifying assumptions, and in each of these levels the second degree nonlinear expressions were given. The assumptions were carefully stated and their implications with respect to the nonlinear theory of elasticity as applied to beams were pointed out. The transformation matrices between the deformed and undeformed blade-fixed coordinates, which were needed in the development of the curvature expressions, were also given for three of the levels of approximation. The present curvature expressions and transformation matrices were compared with corresponding expressions existing in the literature.

Kvaternik, R. G.↗

NASA NTRS1960

An Approximate Analytical Method for Studying Atmosphere Entry of Vehicles with Modulated Aerodynamic Forces

The dimensionless, transformed, nonlinear differential equation developed in NASA TR R-11 for describing the approximate motion and heating during entry into planetary atmospheres for constant aerodynamic coefficients and vehicle shape has been modified to include entries during which the aerodynamic coefficients and the vehicle shape are varied. The generality of the application of the original equation to vehicles of arbitrary weight, size, and shape and to arbitrary atmospheres is retained. A closed-form solution for the motion, heating, and the variation of drag loading parameter m/C(D)A has been obtained for the case of constant maximum resultant deceleration during nonlifting entries. This solution requires certain simplifying assumptions which do not compromise the accuracy of the results. The closed-form solution has been used to determine the variation of m/C(D)A required to reduce peak decelerations and to broaden the corridor for nonlifting entry into the earth's atmosphere at escape velocity. The attendant heating penalty is also studied.

Levy, Lionel L., Jr.↗