SEARCH · Search NASA

Results for “PRESSURE RECOVERY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

All sources NASA NTRS DOE OSTI

NASA NTRS1975

Inlet performance of the integrated Langley scramjet module

The inlet concept for the Langley Scramjet Module has been developed and proven in Langley wind tunnels over a Mach number range from 2.3 to 6.0 (flight simulation of Mach 2.6 to 7.6). This modular engine concept is designed to integrate with the airframe, which results in precompression of the engine airflow by the vehicle bow shock and additional expansion of the nozzle exhaust gas by the afterbody of the vehicle. With these integration advantages, the inlet can be designed with modest contraction ratios and fixed geometry. Also, the module nozzle exit area can be equal to the capture area, which permits the cowl to be alined with the local flow producing minimum external drag. The inlet leading edges and planar compression surfaces are swept at 48 deg, which provides spillage at low Mach numbers for starting and which reduces the pressure gradient on the top surface to permit ingestion of the vehicle forebody boundary layer into the inlet without separating. Three fuel injection struts provide for the use of a short combustor having low internal cooling requirements. Schedules for mass capture ratio, contraction ratio, and total pressure recovery are well within the acceptable range for a good scramjet propulsion device. The fixed geometry, minimum external drag design has proven to be a practical, high-performance inlet concept.

Trexler, C. A.↗

NASA NTRS1976

Boundary layer bleed system study for a full-scale, mixed-compression inlet with 45 percent internal contraction

The results of an experimental bleed development study for a full-scale, Mach 2.5, axisymmetric, mixed-compression inlet were presented. The inlet was designed to satisfy the airflow requirements of the TF30-P-3 turbofan engine. Capabilities for porous bleed on the cowl surface and ram-scoop/flush-slot bleed on the centerbody were provided. A configuration with no bleed on the cowl achieved a minimum stable, diffuser exit, total pressure recovery of 0.894 with a centerbody-bleed mass flow ratio of 0.02. Configurations with cowl bleed had minimum stable recoveries as high as 0.900 but suffered range decrement penalties from the increased bleed mass flow removal. Limited inlet stability and unstart angle-of-attack data are presented.

Shaw, R. J.↗

NASA NTRS1975

Quiet, clean short-haul experimental engine (QCSEE) test results from a 14 cm inlet for a variable pitch fan thrust reverser

A 1/13th scale model of the fan discharge duct was tested with a matrix of flare exlets. Exlets are flared fan nozzles configured for improved reverse flow inlet performance for reverse pitch fan applications. Results showed that a flare type exlet is an acceptable design for QCSEE, as indicated by high pressure recovery and low distortion performance.

Vier, W. F.↗

NASA NTRS1976

A numerical solution of the flow field over a transonic airfoil including strong-shock-induced flow separation

An approximate numerical method has been developed for computing the entire transonic flow field over an airfoil, including the boundary layer, the shock-wave/boundary-layer interaction, and the shock-induced-separation. The inviscid flow, the turbulent boundary layer in the weak interaction zone, and the strong interaction elliptic region are solved separately. The inviscid flow is represented by the solution of the transonic small-disturbance equation, while the boundary layer is solved by the generalized Galerkin method, and the strong interaction region (including the wake) is computed from the time-averaged Navier-Stokes equations. A second-order interaction is computed iteratively using the inviscid pressure distribution as a boundary condition for the boundary layer and Navier-Stokes codes, and the viscous displacement thickness to modify the airfoil geometry for the inviscid computation. The computed pressure distributions and shock-wave profiles are compared with experimental data. Agreement is very good except that the pressure recovery on the trailing edge is greater than the experimental data.

Seginer, A.↗

NASA NTRS1976

Transonic performance of Mach 2.65 auxiliary flow axisymmetric inlet

Transonic experimental performance for a large scale Mach 2.65 axisymmetric inlet model with auxiliary airflow systems are presented. The inlet model incorporated both centerbody and cowl auxiliary airflow systems. When the centerbody system was fully open the performance at the simulated compressor face was such that, at 0.10 total pressure distortion the total capture mass flow ratio increased 0.055 and 0.051 and the total pressure recovery increased 0.015 and 0.012 at Mach 0.9 and 1.3, respectively. Flow separation on the centerbody resulted in supercritical centerbody auxiliary throat flow prior to attainment of choked main duct throat flow. Cowl auxiliary airflow had a detrimental effect on compressor-face performance. To overcome the detrimental effect, alternate cowl auxiliary airflow systems are described for efficient merging of auxiliary and main duct airflows and for providing similar auxiliary and main duct throat choking characteristics.

Santman, D. M.↗

NASA NTRS1976

A simplified analysis of propulsion installation losses for computerized aircraft design

A simplified method is presented for computing the installation losses of aircraft gas turbine propulsion systems. The method has been programmed for use in computer aided conceptual aircraft design studies that cover a broad range of Mach numbers and altitudes. The items computed are: inlet size, pressure recovery, additive drag, subsonic spillage drag, bleed and bypass drags, auxiliary air systems drag, boundary-layer diverter drag, nozzle boattail drag, and the interference drag on the region adjacent to multiple nozzle installations. The methods for computing each of these installation effects are described and computer codes for the calculation of these effects are furnished. The results of these methods are compared with selected data for the F-5A and other aircraft. The computer program can be used with uninstalled engine performance information which is currently supplied by a cycle analysis program. The program, including comments, is about 600 FORTRAN statements long, and uses both theoretical and empirical techniques.

Morris, S. J., Jr.↗

NASA NTRS1975

Design of high lift airfoils with a Stratford distribution by the Eppler method

Airfoils having a Stratford pressure distribution, which has zero skin friction in the pressure recovery area, were investigated in an effort to develop high lift airfoils. The Eppler program, an inverse conformal mapping technique where the x and y coordinates of the airfoil are developed from a given velocity distribution, was used.

Thomson, W. G.↗

NASA NTRS1977

Introductory Remarks

Advanced transonic configurations, such as the supercritical wing, are inherently more sensitive to Reynolds number than earlier configurations because the pressure recovery gradients imposed on the boundary layer are generally steeper. The results of two-dimensional supercritical airfoil investigations and theoretical calculations show this effect. A technique for approximately simulating full-scale Reynolds number characteristics at present wind-tunnel Reynolds numbers for near-cruise conditions is described. The transition strip, which in the past has been located near the leading edge of the wing, is rearward so that the relative displacement thickness of the boundary layer at the trailing edge of the wing is the same as might be expected on a full-scale configuration with the transition near the leading edge. Two-dimensional wind-tunnel results indicate that the technique provides a very good simulation of airfoil characteristics at full-scale Reynolds number. The need for sorting the effects of Reynolds number and aeroelasticity, which can be done in the NTF, is also addressed.

Whitcomb, R.↗

NASA NTRS1977

Operating characteristics of an inlet model tested with a 0.5m powered fan at high angles of attack

An inlet model designed for high angle of attack capability, coupled to a .508 m tip diameter turbofan simulator, was tested in the NASA-Lewis Research Center's 9-by 15-ft low speed wind tunnel. The test variables were: tunnel velocity, 0 to 75 m/s; inlet angle of attack, 0 to 120 deg; and fan face corrected airflow per unit area, 75 to 200 kg/s sqm. The inlet flow separation boundaries, the fan face total pressure recovery and distortion characteristics, and the fan blade vibratory stresses were determined. The recovery, distortion, and stress levels showed no abrupt changes at the onset of separation, but became gradually more unfavorable as the size and intensity of the separation increased as induced by increasingly severe operating conditions. Performance characteristics for a large scale model of the inlet were estimated from these test results.

Koncsek, J. L.↗

NASA NTRS1977

Transonic performance of an auxiliary airflow system for axisymmetric inlets

A large-scale model of an axisymmetric inlet with a centerbody auxiliary airflow system has been tested in the wind tunnel at transonic speeds. The auxiliary system allows additional airflow (other than in the main duct formed by the cowl and translating centerbody) to pass through the centerbody of the inlet and combine with the main duct airflow on its way to the engine face. The results of the tests are presented, and the inlet performance is compared to a closely related alternative inlet with a 'traveling' boundary-layer bleed system which precludes the use of a centerbody auxiliary airflow system. The comparison shows that the auxiliary airflow inlet can supply 7.7% more engine face airflow at Mach number 1.0 and is 26% shorter than the traveling bleed inlet. Even though maximum transonic airflow was not achieved at a comparable engine face mass-flow ratio of 0.580, a total-pressure distortion of 0.10 and a total-pressure recovery of 0.985 were achieved for the auxiliary airflow inlet while a recovery of only 0.965 was achieved for the traveling bleed inlet.

Sorensen, N. E.↗

NASA NTRS1977

An approximate calculation of the strong interaction on a transonic airfoil

This paper describes an interactive computational scheme that calculates the transonic flow field over an airfoil. The inviscid flow, the turbulent boundary layer in the weak interaction region, and the elliptic flow in the strong interaction region are computed separately, and the solutions are matched iteratively in a direct, second-order interaction scheme. The pressure distribution, obtained from a transonic, small-perturbation solution, is prescribed on the boundary layer and the Navier-Stokes equations and the ensuing displacement thicknesses are used to modify the inviscid flow. The best overall results are obtained by using a turbulence model that eliminates the eddy viscosity in the strong interaction region. Computed pressure distributions are compared with experimental data and with Navier-Stokes solutions. In weak interactions, the agreement with experimental data is very good, as it is also in strong interactions except for the pressures in the separated-flow region. There the agreement is qualitative only, and the pressure recovery is too high. The results in both cases are superior or equal to those of the Navier-Stokes solutions, and the present method is significantly faster.

Seginer, A.↗

NASA NTRS1977

Use of simplified flow separation criteria for slotted flap preliminary design

From experimental correlations of airfoil and flap pressure distributions, it is observed that flow separation is likely to occur when the canonical pressure recovery coefficient (C sub pr) exceeds a critical value. A procedure is described for obtaining the C sub pr parameter from modified inviscid analysis. The procedure has been applied to preliminary design studies of a new slotted flap to determine the influence of shape and location. Experiments are planned to evaluate the flap designed by this procedure.

Wentz, W. H., Jr.↗

NASA NTRS1978

Performance characteristics of two annular dump diffusers using suction-stabilized vortex flow control

Test results are described for two abrupt area change annular diffusers with provisions for maintaining suction stabilized toroidal vortices at the area discontinuity. Both diffusers had an overall area ratio of 4.0 with the prediffuser area ratio being 1.18 for diffuser A and 1.4 for diffuser B. Performance was evaluated at near atmospheric pressure and temperature for a range of inlet Mach numbers from 0.18 to 0.41 and suction rates from 0 to 18%. Static pressure recovery improved significantly as the suction rate was increased to approximately 11%. Results obtained with diffuser A were superior to that obtained with diffuser B. Flat radial profiles of exit velocity were not obtained since the flow showed preferential hub or tip attachment at moderate suction rates. At high suction rates the diffuser exit flow became circumferentially nonuniform and unstable.

Juhasz, A. J.↗

NASA NTRS1976

Inlet technology for powered-lift aircraft

The concepts, analytical tools, and experimental data available for designing inlets for powered lift aircraft are discussed. It is shown that inlets can be designed to meet noise, distortion, and cruise drag requirements at the flight and engine operating conditions of a powered lift aircraft. The penalty in pressure recovery for achieving the required noise suppression was 0.3 percent.

Luidens, R. W.↗

NASA NTRS1978

Cold-air performance of the compressor-drive turbine of the Department of Energy baseline automobile gas-turbine engine

The aerodynamic performance of the compressor-drive turbine of the DOE baseline gas-turbine engine was determined over a range of pressure ratios and speeds. In addition, static pressures were measured in the diffusing transition duct located immediately downstream of the turbine. Results are presented in terms of mass flow, torque, specific work, and efficiency for the turbine and in terms of pressure recovery and effectiveness for the transition duct.

Roelke, R. J.↗

NASA NTRS1979

Experiments on tandem diffusers with boundary-layer suction applied in between

Experiments were performed on conical diffusers of various configurations with the same, but rather unusually large, 16:1 area ratio. Because available performance data on diffusers fall short of very large area ratio configurations, an unconventional design, consisting of two diffusers following each other in tandem, was proposed. Both diffusers had the same area ratio of 4:1, but had different taper angles. While for the first diffuser (called leading) the angle remained constant, for the second (called follower), the taper angle was stepped up to higher values. Boundary layer control, by way of suction, was applied between the diffusers, and a single slot suction ring was inserted between them. The leading diffuser had an enclosed nominal divergence angle 2 theta = 5 degrees, while the follower diffusers had either 10, 20, 30, or 40 degrees, respectively, giving 4 combinations. The experiments were performed at four different Reynolds numbers with various suction rates. The rates indicate a general improvement in the performance of all diffusers with boundary layer suction. It appears that the improvement of the pressure recovery depends on both the Reynolds number and the suction rate, and the largest increase, 0.075, was found at the lowest R sub e when the follower divergence was 2 theta = 40 degrees.

Barna, P. S.↗

NASA NTRS1979

Performance of a V/STOL tilt nacelle inlet with blowing boundary layer control

A scale model of a V/STOL tilt nacelle fitted to a 0.508 m single stage fan was tested in the NASA Lewis 9x15 ft low speed wind tunnel to determine the effect of diffuser blowing on the inlet aerodynamics and aeromechanical performance. The test was conducted over a range of freestream speeds (up to 120 knots) and angles of attack (up to 120 deg). Diffuser blowing had a beneficial affect on all performance parameters. The angle of attack range for separation free flow substantially increased, and the fan face distortion significantly reduced with a corresponding increase in total pressure recovery. Discrete narrow band blade stress peaks which were common to the nonblowing (baseline) configuration were eradicated with diffuser blowing.

Johns, A. L.↗

NASA NTRS1979

Performance of a V/STOL tilt nacelle inlet with blowing boundary layer control

A scale model of a V/STOL tilt nacelle fitted to a 0.508 m single stage fan was tested in the NASA Lewis low speed wind tunnel to determine the effect of diffuser blowing on the inlet aerodynamics and aeromechanical performance. The test was conducted over a range of freestream speeds (up to 120 knots) and angles-of attack (up to 120 deg). In general, diffuser blowing had a beneficial affect on all performance parameters. The angle-of-attack range for a separation-free flow substantially increased, and the fan face distortion reduced with a corresponding increase in total pressure recovery. Discrete narrow band blade stress peaks which were common to the nonblowing (baseline) configuration were eradicated with diffuser blowing.

Johns, A. L.↗