Search NASA⌕ Search

SEARCH · Search NASA

Results for “Phase III”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

The high pressure crystal structures of tin sulphate: a case study for maximal information recovery from 2D powder diffraction data

Our recently proposed method for automatic detection, calibration and evaluation of Debye-Scherrer ellipses using pattern recognition techniques and advanced signal filtering was applied to 2D powder diffraction data of tin sulphate in dependence on pressure. Three phase transitions towards higher pressure could be identified, and their respective crystal structures have been determined. The high pressure behaviour of the stereoactive lone pair of Sn{sup 2+} was investigated. At ambient conditions, SnSO{sub 4} crystallizes in a strongly distorted Barite structure type in space group Pnma (phase I). In the pressure range between P = 0.15 and P = 0.2 GPa, it exhibits a displacive second order phase transition into a structure with space group P112{sub 1}/a (phase II at P = 0.2 GPa: a = 8.7022(9) {angstrom}, b = 5.3393(5) {angstrom}, c = 7.0511(6) A, y = 89.90(1){sup o}). A second displacive phase transition occurs between P = 4.40 and P = 5.07 GPa into another structure with space group PI (phase III at P = 13.5 GPa: a = 8.067(3) {angstrom}, b = 5.141(2) {angstrom}, c = 6.609(2) {angstrom}, a = 90.56(3){sup o}, {beta} = 90.65(2){sup o}, y = 89.46(2){sup o}). A third displacive phase transition towards another crystal structure in space group P1 occurs between P = 13.6 and P = 15.3 GPa (phase IV at P = 20.5 GPa: a = 7.889(5) {angstrom}, b = 5.028(3) {angstrom}, c = 6.462(3) {angstrom}, a = 90.99(3){sup o}, {beta}=91.01(3){sup o}, y = 89.89(4){sup o}). A non-linear compression behaviour over the entire pressure range is observed, which can be described by three Vinet relations in the ranges from P = 0.21 to 4.4 GPa, from P = 5.07 to 13.55 GPa and from P = 15.26 to 20.5 GPa. The extrapolated bulk moduli of the high-pressure phases were determined to K{sub 0} = 48(1) GPa for phase II, K{sub 0} = 56(2) GPa for phase III, and K{sub 0} = 51(13) GPa for phase IV. The crystal structures of all phases are refined against X-ray powder diffraction data measured at several pressures between 0.15 and 20.5 GPa. The structural phase transitions of SnSO{sub 4} are mainly characterized by a reorientation of the SO{sub 4} tetrahedra, in order to optimize crystal packing. With increasing pressure, the lone pair which is localized at Sn{sup 2+} increasingly adopts pure s-character.

36 MATERIALS SCIENCE↗

Verification and Validation of Optimization of Replacement Portal Monitoring Replay Tools

The Los Alamos National Laboratory and the Johns Hopkins Applied Physics Laboratory (APL) are both developing optimization software to fulfill the objective of Phase III of the Replacement Portal Monitoring (RPM) Program for the Department of Homeland Security. The objective of the Phase III of the RPM Program is to conduct an evaluation of three RPM systems designed to enhance mission effectiveness, gain operational efficiencies, and to address emerging mission needs against the Countering Weapons of Mass Destruction (CWMD ) nuclear threat basis and special nuclear material (SNM) used in performance testing. As such this task involves the use of global optimization algorithms.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗

Linear canonical transformations of coherent and squeezed states in the Wigner phase space. III - Two-mode states

It is shown that the basic symmetry of two-mode squeezed states is governed by the group SP(4) in the Wigner phase space which is locally isomorphic to the (3 + 2)-dimensional Lorentz group. This symmetry, in the Schroedinger picture, appears as Dirac's two-oscillator representation of O(3,2). It is shown that the SU(2) and SU(1,1) interferometers exhibit the symmetry of this higher-dimensional Lorentz group. The mathematics of two-mode squeezed states is shown to be applicable to other branches of physics including thermally excited states in statistical mechanics and relativistic extended hadrons in the quark model.

Han, D.↗

Brigham City Hydro Generation Project

Brigham City owns and operates its own municipal power system which currently includes several hydroelectric facilities. This project was to update the efficiency and capacity of current hydro production due to increased water flow demands that could pass through existing generation facilities. During 2006-2012, this project completed efficiency evaluation as it related to its main objective by completing a feasibility study, undergoing necessary City Council approvals and required federal environmental reviews. As a result of Phase 1 of the project, a feasibility study was conducted to determine feasibility of hydro and solar portions of the original proposal. The results indicated that the existing Hydro plant which was constructed in the 1960’s was running at approximately 77% efficiency or less. Brigham City proposes that the efficiency calculations be refined to determine the economic feasibility of improving or replacing the existing equipment with new high efficiency equipment design specifically for the site. Brigham City completed the Feasibility Assessment of this project, and determined that the Upper Hydro that supplies the main culinary water to the city was feasible to continue with. Brigham City Council provided their approval of feasibility assessment’s results. The Upper Hydro Project include removal of the existing powerhouse equipment and controls and demolition of a section of concrete encased penstock, replacement of penstock just upstream of the turbine inlet, turbine bypass, turbine shut-off and bypass valves, turbine and generator package, control equipment, assembly, start-up, commissioning, Supervisory Control And Data Acquisition (SCADA), and the replacement of a section of conductors to the step-up transformer. Brigham City increased the existing 575 KW turbine and generator with an 825 KW turbine and generator. Following the results of the feasibility assessment Brigham City pursued required environmental reviews with the DOE and the U.S. Fish and Wildlife Services (USFWS) concurring with the National Environmental Policy Act of 1969 (NEPA) It was determined that Brigham City’s Upper Hydroelectric Power Plant upgrade would have no effect to federally listed or candidate species. However Brigham City has contributed a onetime lump sum towards Bonneville cutthroat trout conservation in the Northern Bonneville Geographic Management Unit with the intention to offset any impacts from the Upper Hydro Project needed to move forward with design and construction and is sufficient for NEPA compliance. No work was done in the river or river bank. During construction, the penstock was disconnected and water was diverted through and existing system around the powerhouse and back into the water system. The penstock, which is currently a 30-inch steel pipe, would be removed and replaced with a new section of 30-inch pipe. Brigham City worked with the DOE and was awarded a new modification and the permission to proceed with Phase III of our Hydro Project in Dec. 2013; with the exception to the modification of the award for the construction phase. Brigham City developed and issued a Request for Proposal for Engineer and Design vendor. Sunrise Engineering was selected for the Design and throughout the Construction Phase of the Upper Hydroelectric Power Plant. Brigham City conducted a Kickoff Meeting with Sunrise June 28, 2013 and received a Scope of Work Brigham City along with engineering firm sent out a RFP for Turbine, Generator and Equipment for Upper Hydro. We select Turbine/Generator Equipment from Canyon Industries located in Deming, WA. DOE awarded Brigham City a new modification and the permission to proceed with Phase III Construction of our Hydro Project. Brigham City Crews removed existing turbine/generator and old equipment alone with feeder wires coming into the building basically giving Caribou Construction an empty shell to begin demolition. Brigham City contracted with Caribou Construction from Jerome, Idaho for the Upper Power Plant construction. A kickoff meeting was June 24, 2014 and demolition was immediately started on building. Because of a delivery delay of Turbine, Generator and Equipment from Canyon Brigham City had to request another extension for the final date of completion. DOE awarded modification (.007) to Brigham City with a new completion date of August 1, 2015. The Turbine has had a few adjustments to help with efficiency; but the Generator had a slight vibration when generator got hot so Canyon Industries had U S Motor’s that manufactured the generator come to check out the issue. The other Equipment seems to be running normal. Brigham City, Sunrise Engineering and Canyon Industries met to determine what the vibration in the generator was and how to solve the issue Us Motor’s found some welds that failed: they have been repaired. U S Motor’s delivered the repaired generator Feb. 17, 2015. Canyon Industries arranged for a crane to installed generator in Power Plant. U S Motor’s balanced and wired generator. Plant Operators put the generator back on line. Canyon Industries returned and gave their approval to keep Hydro online. After Hydro was put back into operations it kept going off line because of overheating issues. Canyon Industries returned and replaced sensors and adjusted them to the proper settings for normal operations. Brigham City added additional steel screens to windows to increase air flow in Power Plant Building. After construction phase of the Upper Hydro Plant some landscaping has been restored around the building additional gravel brought in and leveled out and the road that was cut through for conduits to run wires. A retaining wall was installed to protect penstock. The Upper Hydro Plant is complete and in full operations. The final reimbursement was submitted.

13 HYDRO ENERGY↗

Enhanced terrestrial Fe(II) mobilization identified through a novel mechanism of microbially driven cave formation in Fe(III)-rich rocks

Most cave formation requires mass separation from a host rock in a process that operates outward from permeable pathways to create the cave void. Given the poor solubility of Fe(III) phases, such processes are insufficient to account for the significant iron formation caves (IFCs) seen in Brazilian banded iron formations (BIF) and associated rock. Here in this study we demonstrate that microbially-mediated reductive Fe(III) dissolution is solubilizing the poorly soluble Fe(III) phases to soluble Fe(II) in the anoxic zone behind cave walls. The resultant Fe(III)-depleted material (termed sub muros) is unable to maintain the structural integrity of the walls and repeated rounds of wall collapse lead to formation of the cave void in an active, measurable process. This mechanism may move significant quantities of Fe(II) into ground water and may help to explain the mechanism of BIF dissolution and REE enrichment in the generation of canga. The role of Fe(III) reducing microorganism and mass separation behind the walls (outward-in, rather than inward-out) is not only a novel mechanism of speleogenesis, but it also may identify a previously overlooked source of continental Fe that may have contributed to Archaean BIF formation.

54 ENVIRONMENTAL SCIENCES↗

Methodology Paper for Upper Cretaceous Sandstone Characterization

The Southeast Regional Carbon Sequestration Partnership’s (SECARB’s) Anthropogenic Test is a demonstration of the deployment of CO 2 capture, transport, geologic storage and monitoring technologies. The capture component of the test takes place at the James M. Barry Electric Generating Plant in Bucks, Alabama. The capture facility utilizes post-combustion amine capture technology licensed from Mitsubishi Heavy Industries America to process flue gas from a coal-fired power unit at Plant Barry. The amount of CO 2 captured using this process is equivalent to the emissions produced when generating 25 megawatts (MW) of electricity. CO 2 captured at the plant is transported by pipeline for underground storage in a saline geologic formation within the Citronelle Dome. This project is one of the first and the largest fully-integrated commercial prototype coal-fired carbon capture and storage projects in the USA. This demonstration is currently in the injection phase, with the capture unit reaching full operational capacity in June of 2011. The project constructed a twelve mile long, 4-inch diameter pipeline to the injection site starting in July 2011. Drilled in January 2011, a deep characterization well provided geologic data confirming that the test site represented an attractive location for safe, long-term storage of CO 2 . Two Class V Experimental Injection Well underground injection control (UIC) permits were issued in November 2011 and subsequently the project’s injection wells were installed. A robust monitoring, verification and accounting (MVA) plan has been developed to monitor and track the CO 2 plume and the associated pressure field. In association with this field demonstration, the project team is also tasked with the continued characterization of this region’s potential storage reservoirs and cap rock formations. This document serves as the SECARB Phase III work product 1.1.a “Methodology Paper for Upper Cretaceous Sandstone Characterization.” This product will summarize the Project Team’s plans for the Phase III assessment of the Upper Cretaceous Sandstone Reservoir’s CO 2 storage capacity.

54 ENVIRONMENTAL SCIENCES↗

Risk Characterization Research for Artemis II: Human Factors and Behavioral Performance

BACKGROUND Artemis II will be the first time NASA astronauts go beyond low-Earth orbit (LEO) since the Apollo era, and the first astronauts heading into space in the Orion vehicle. As such, it provides a critical opportunity to refine our understanding of the likelihood and consequences associated with the Behavioral Medicine (BMed), Team, Human System Integration Architecture (HSIA), and Sleep Risks, and prepare for future Moon and Mars missions. However, Artemis II research efforts are uniquely shaped by in-mission data collection constraints. There is currently no in-mission crew time available to complete measures. In-mission data will need to be collected unobtrusively from available data streams (e.g., audiovisual, existing records such as schedules, and actigraphy). Accordingly, the overarching goal of our research is to utilize Artemis II data to further define the likelihood and consequences of these risks, and to create an unobtrusive research infrastructure that can be expanded to include future Artemis missions. This goal spans four aims across three research phases: (1) identify and operationally define key performances metrics and constructs across the four aforementioned risks, (2) develop an unobtrusive methodology and coding scheme for in-mission data collection, (3) characterize performance decrements due to Bmed, Team, HSIA, and Sleep Risks, and (4) develop a data infrastructure for future Artemis missions. The following details results of Phase I efforts in which we address Aims 1 and 2 to develop an unobtrusive measurement plan and coding scheme to capture key constructs, contributing factors, and performance decrements across each risk area. METHOD As part of Phase I, we conducted an interdisciplinary literature review and consulted with SMEs to identify unobtrusive methodologies that leverage text, audio, and/or video data as well as conceptualize key performance metrics, contributing factors, and BMed, Team, HSIA, and Sleep risk constructs related to performance decrements. The Phase I effort resulted in a finalized pre- and post-mission protocol for Artemis II, along with a measurement and coding scheme for in-mission Artemis II data. Phase II will involve data collection from the upcoming Artemis II mission. Phase III will include data processing, coding, depiction, analysis, and report writing of the Artemis II data. RESULTS & DISCUSSION To date, we have completed Phase I efforts. Specifically, we identified BMed, Team, HSIA, and Sleep risk constructs related to performance metrics, summarized how these constructs can be measured using audiovisual data collected during the mission, and worked with NASA’s HFBP Element to finalize a data collection protocol that leverages audiovisual input from the Orion spacecraft system. Our protocol includes novel unobtrusive methodologies that adhere to in-mission data streams and subsequent constraints (e.g., limited storage space on GoPro cameras, ambient noise impeding audio files) to best capture in-mission phenomena across each risk area. We will present our results from Phase I efforts, namely best practices for unobtrusive measurement as identified through literature reviews and SME consultation as well as codebook excerpts for use in Artemis II. We will include a description of planned work as we prepare for Phase II and Phase III of this research plan and the Artemis II mission itself. SUMMARY We describe progress on our Human Factors and Behavioral Performance Research for Artemis II study.

behavioral health↗

Sodium superionic conduction in tetragonal Na{sub 3}PS{sub 4}

Highlights: • Na{sub 3}PS{sub 4} base solid electrolytes were fabricated by various synthetic routes. • The formation of phases in Na{sub 3+5x}P{sub 1–x}S{sub 4} depends on reaction conditions. • Tetragonal phase III showed the highest conductivity of 3.39 × 10{sup -3} S cm{sup -1}at 25 °C. • Structural analysis revealed the 3D conduction pathway in the tetragonal phase III. • Na{sub 3}PS{sub 4} functions as a solid electrolyte in all-solid-state sodium batteries. - Abstract: Sodium superionic conductors are highly promising as solid electrolytes for all-solid-state sodium batteries, with the capacity to improve energy and power density of liquid-electrolyte-based batteries and to address their safety issues. However, the ionic conductivity of sodium electrolytes remains roughly one order of magnitude lower than that of lithium systems. Herein, we report a synthesis method for a sodium superionic conductor, tetragonal Na{sub 3}PS{sub 4}, with an ionic conductivity of 3.39 × 10{sup −3} Scm{sup −1} at 25 °C—the highest value yet reported among sulfide-type sodium conductors. The high conductivity is achieved through quenching from 700 °C, which introduces sodium vacancies, and annealing at 450 °C, which increases vacancies and expands lattice volume. The phase is comprised of a framework of isolated PS{sub 4} tetrahedra, with partial distribution of Na over 3D pathways. The high intrinsic conductivity together with low grain boundary contribution and soft mechanical properties make Na{sub 3}PS{sub 4} a promising candidate for sodium solid electrolytes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Analysis of WakeVAS Benefits Using ACES Build 3.2.1

The FAA and NASA are currently engaged in a Wake Turbulence Research Program to revise wake turbulence separation standards, procedures, and criteria to increase airport capacity while maintaining or increasing safety. The research program is divided into three phases: Phase I near term procedural enhancements; Phase II wind dependent Wake Vortex Advisory System (WakeVAS) Concepts of Operations (ConOps); and Phase III farther term ConOps based on wake prediction and sensing. This report contains an analysis that evaluates the benefits of a closely spaced parallel runway (CSPR) Phase I ConOps, a single runway and CSPR Phase II ConOps and a single runway Phase III ConOps. A series of simulation runs were performed using the Airspace Concepts Evaluation System (ACES) Build 3.21 air traffic simulator to provide an initial assessment of the reduction in delay and cost savings obtained by the use of a WakeVAS at selected U.S. airports. The ACES simulator is being developed by NASA Ames Research Center as part of the Virtual Airspace Modelling and Simulation (VAMS) program.

Smith, Jeremy C.↗

Deep Controlled Source Electro-Magnetic Sensing: A Cost Effective, Long-Term Tool for Sequestration Monitoring

The proposed system was designed to operate as a permanent, autonomous monitoring and data collection system that can provide much higher temporal data density than can be achieved economically with 3-Dimensional (3D) seismic surveys. It can operate over broad areas for long periods of time providing full 3D data sets on a monthly basis at a very low cost. By borrowing techniques commonly used in marine CSEM, structural information from background seismic surveys can be incorporated into the CSEM modeling to provide high resolution models of CO 2 progression within reservoirs. The system uses borehole-based vertical-electric-dipole sources placed at reservoir depths in the formation. The electric and magnetic fields induced by this source are received on the surface using an array of stations. The project was conducted in three phases. Phase I demonstrated the feasibility of the system to collect static/reference data at the Ketzin CO 2 storage pilot site in Germany. In Phase I, numerical modeling was used to determine the optimal configurations and requirements for sensor sensitivity and data accuracy. Based on the model results, existing hardware and software were modified. The CSEM system was then field tested at the Ketzin site. The data were imaged and the results were compared with independent studies of the reservoir and overburden geo-electrical characteristics. Phase II demonstrated the ability to provide sensitive, cost-effective measurement of changes in reservoir properties and changes in the overlying formations using a second round of measurements at the Ketzin site. A prototype autonomous recording system was developed and tested as a subset of the measurement points. Phase III of the project quantified the advantages (and disadvantages) of the fully autonomous data collection subsystems by comparing them with repeated measurements made with mobile stations. The Phase III also provided an additional time point in measuring post-closure changes in and above the Ketzin CO 2 injection site. Validation of the CSEM field survey results were completed using a method such as other alternative and available field site data.

58 GEOSCIENCES↗

NIAC: The NASA Innovative Advanced Concepts Program

The NASA Innovative Advanced Concepts (NIAC) Program nurtures visionary ideas that could transform future NASA missions with the creation of breakthroughs - radically better or entirely new aerospace concepts - while engaging America's innovators and entrepreneurs as partners in the journey. NIAC projects study innovative, technically credible, advanced concepts that could one day “Change the Possible” in aerospace. NIAC supports innovative research through three phases of study, each competitively awarded. Phase I studies are for nine-month efforts to explore the overall viability of visionary concepts. Phase II studies further develop the most promising Phase I concepts for up to two years, prepare a roadmap for further development, and explore potential transition options within NASA and beyond. Phase III studies are designed to strategically transition the most promising NIAC concepts to other NASA programs, other government agencies, or commercial partners. Since 2011, NIAC has funded 128 Phase I, 51 Phase II, and 2 Phase III studies. This paper provides an update on NIAC’s history and current role in supporting NASA’s sustained investments in advanced aerospace technology development.

Innovation↗

TPSAS-NF1676L-13678-DND

An area that shows promise in enhancing structural integrity of aircraft and aerospace structures is integral stitched composite technology. The most recent generation of this technology is the Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) concept. The goal of the PRSEUS concept is to provide damage-containment capability for composite structures while reducing overall structural weight. The National Aeronautics and Space Administration, the Boeing Company, and the Federal Aviation Administration (FAA) have partnered in an effort to assess the damage-containment features of a full-scale curved PRSEUS panel using the FAA Full-Scale Aircraft Structural Test Evaluation and Research facility. The background, test plan, fixture modifications, pre-test analysis, and planned experimental procedure were presented at the 2011 Aircraft Airworthiness and Sustainment Conference. This follow-on paper and presentation will provide details of the experimental procedure, test results, nondestructive inspection results, and preliminary test analysis comparison. The test program included three phases of loading and inspections: Phase I, as-built; Phase II, with barely visible impact damage (BVID); and Phase III, with a two-bay notch severing the central stiffener. Axial tension, internal pressure, and combined axial tension and internal pressure load conditions were applied during each phase using load levels that demonstrate compliance with the strength, deformation, and damage-tolerance requirements of Title 14 Code of Federal Regulations Part 25. Pressure loads were based on an operating pressure of 9.2 psi, designated as 1P, and the axial loads were based on a design limit load (DLL) of 227 kip. The Phase I test results provided a baseline. First, 50 percent limit-load levels were applied for each of the three load cases to verify proper load introduction and repeatability by examining strain and displacement results. Next, three limit-load cases were applied: limit pressure of 12.2 psi (1.33 P), axial DLL of 227 kip, and combined 1P pressure and axial DLL. Linear strain and displacement results were observed in all load cases. For Phase-II testing, the panel was impacted to introduce BVID with an energy of 40 ft-lb, with the impact located between the central stringer stitch line and flange edge. The impact created non-penetrating visual damage with fiber breaks and delamination between the skin and stringer flange. Limit-load conditions were applied followed by pressure overload of 18.4 psi (2P) and ultimate load conditions, defined as 1.5 times DLL. Inspections were performed after each load case; no damage growth was observed. For Phase-III testing, a two-bay notch was machined severing the central stiffener. The panel was then subjected to limit-load conditions, followed by combined 1P pressure while increasing axial tension load to catastrophic failure. As limit combined loads were approached, damage initiation was observed in the form of 45? splitting at 1P + 79% DLL. Axial loading was increased to 1P + 150 percent DLL causing damage to propagate to the adjacent stringer flanges. Damage was contained within the two-bay region by the stitching rows up to 1P + 176% DLL. Axial load was further increased until catastrophic failure, when a stringer rod failed at 1P + 192% DLL. These test results further verify the damage containment features of the PRSEUS concept and suggest its appropriateness for future flight vehicles.

Andrew Bergan↗

Hydrogen-Doped Polymeric Carbon Monoxide at High Pressure

The ability to control materials stability, bonding, and transformation by thermo-mechanical and chemical means is significant for development of high-energy-density extended solids. We report that doping hydrogen (~10%) in carbon monoxide (CO) can greatly lower the polymerization pressure of CO and enhance the stability of recovered polymeric CO products at ambient conditions. Hydrogen-doped CO crystallizes into well-grown dendrites of β-CO-like phase at 3.2 GPa, which polymerizes to highly unsaturated black polymer (phase I) at ~4.7 (5.8) GPa. Upon further compression, this highly colored polymer transforms into a translucent 3D network structure (phase II) at 6–7 (10–17) GPa and then a transparent 2D layer structure (phase III) at 20–30 (30–60) GPa. A similar series of transformations are also found in pure CO but at considerably higher transition pressures, as noted in parentheses. All polymeric phases are recoverable at ambient conditions, exhibiting an array of phase stability and novel properties such as chemically unstable phase I, highly luminescent phase II, and highly transparent layered phase III. The density of recovered products ranges from ~2.3 g/cm 3 to 3.6 g/cm 3 , depending on the pressure recovered. The recovered products are highly disordered but slowly decompose to crystalline solids of anhydrous polymeric oxalic acid while exhibiting interesting crystal morphologies such as nm-cobs, nm-lamellar layers, and μm-bales. Here, the present first-principles MD simulations suggest that the polymerization occurs at 6 (or 10) GPa in H 2 -doped (or pure) CO. While not directly participating in the reaction, the role of H 2 molecules is to enhance the mobility of CO molecules leading to the polymerization.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Larynx Preservation Clinical Trial Design: Key Issues and Recommendations-A Consensus Panel Summary

Purpose: To develop guidelines for the conduct of Phase III clinical trials of larynx preservation in patients with locally advanced laryngeal and hypopharyngeal cancer. Methods and Materials: A multidisciplinary international consensus panel developed recommendations after reviewing results from completed Phase III randomized trials, meta-analyses, and published clinical reports with updates available through November, 2007. The guidelines were reviewed and approved by the panel. Results: According to the recommendations, the trial population should include patients with T2 or T3 laryngeal or hypopharyngeal squamous cell carcinoma not considered for partial laryngectomy and exclude those with laryngeal dysfunction or age greater than 70 years. Functional assessments should include speech and swallowing. Voice should be routinely assessed with a simple, validated instrument. The primary endpoint should capture survival and function. The panel created a new endpoint: laryngo-esophageal dysfunction-free survival. Events are death, local relapse, total or partial laryngectomy, tracheotomy at 2 years or later, or feeding tube at 2 years or later. Recommended secondary endpoints are overall survival, progression-free survival, locoregional control, time to tracheotomy, time to laryngectomy, time to discontinuation of feeding tube, and quality of life/patient-reported outcomes. Correlative biomarker studies for near-term trials should include estimated glomerular filtration rate, excision repair cross-complementary-1 gene, E-cadherin and {beta}-catenin, epiregulin and amphiregulin, and TP53 mutation. Conclusions: Revised trial designs in several key areas are needed to advance the study of larynx preservation. With consistent methodologies, clinical trials can more effectively evaluate and quantify the therapeutic benefit of novel treatment options for patients with locally advanced laryngeal and hypopharyngeal cancer.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

San Marco D/L Explorer

ti March 26, 1964, Centro Ricerche Aerospaziali (CRA) successfully launched a two-stage Nike sounding rocket from the Santa Rita launch platform off the Kenya coast, concluding Phase I. It carried basic elements of the San Marco science instrumentation and served further to flight qualify these canponents as well as provide a means of check-out of range instrumentation and equipment. The second phase culminated in the launch of the San Marco-I Spacecraft fran Wallops Island on a Scout vehicle on December 15, 1964. This launch derronstrated the readiness of the CRA launch crews for Phase III operations and qualified the basic spacecraft design. In addition it confirmed the usefulness and reliability of the drag balance device for accurate determinations of air density values and satellite attitude. phase III was completed with the launching of San Marco-11 frcm the San Marco platform off the coast of Kenya on April 26, 1967. ?he San Marco-II carried the same instrunentation as the San Marco-I, but the equatorial orbit permitted a more detailed study to be made of density variations versus altitude in the equatorial region. Ihe successful launch also served to qualify the San Marco Range as a reliable facility for future satellite launches. The successful culmination of the first San Marco endeavor paved the way for still closer collaboration in future space explorations.

Source record↗

Single-Crystal Sapphire Optical Fiber Sensor Instrumentation

This report summarizes technical progress on the program “Single-Crystal Sapphire Optical Fiber Sensor Instrumentation,” funded by the National Energy Technology Laboratory of the U.S. Department of Energy, and performed by the Center for Photonics Technology of the Bradley Department of Electrical and Computer Engineering at Virginia Tech. This project was completed in three phases, each with a separate focus. Phase I of the program, from October 1999 to April 2002, was devoted to development of sensing schema for use in high temperature, harsh environments. Different sensing designs were proposed and tested in the laboratory. Phase II of the program, from April 2002 to April 2009, focused on bringing the sensor technologies, which had already been successfully demonstrated in the laboratory, to a level where the sensors could be deployed in harsh industrial environments and eventually become commercially viable through a series of field tests. Also, a new sensing scheme was developed and tested with numerous advantages over all previous ones in Phase II. Phase III of the program, September 2009 to December 2013, focused on development of the new sensing scheme for field testing in conjunction with materials engineering of the improved sensor packaging lifetimes. In Phase I, three different sensing principles were studied: sapphire air-gap extrinsic Fabry-Perot sensors; intensity-based polarimetric sensors; and broadband polarimetric sensors. Black body radiation tests and corrosion tests were also performed in this phase. The outcome of the first phase of this program was the selection of broadband polarimetric differential interferometry (BPDI) for further prototype instrumentation development. This approach is based on the measurement of the optical path difference (OPD) between two orthogonally polarized light beams in a single-crystal sapphire disk. At the beginning of Phase II, in June 2004, the BPDI sensor was tested at the Wabash River coal gasifier facility in Terre Haute, Indiana. Due to business conditions at industrial partner and several logistical problems, this field test was not successful. An alternative high-temperature sensing system using sapphire wafer-based extrinsic Fabry-Perot interferometry was then developed as a significant improvement over the BPDI solution. From June 2006 to June 2008, three consecutive field tests were performed with the new sapphire wafer sensors at the TECO coal gasifier in Tampa, Florida. One of the sensors survived in the industrial coal gasifier for 7 months, over which time the existing thermocouples were replaced twice. The outcome of these TECO field tests suggests that the sapphire wafer sensor has very good potential to be commercialized. However packaging and sensor protection issues need additional development. During Phase III, several major improvements in the design and fabrication process of the sensor have been achieved through experiments and theoretical analysis. Studies on the property of the key components in the sensor head, including the sapphire fiber and sapphire wafer, were also conducted, for a better understanding of the sensor behavior. A final design based on all knowledge and experience has been developed, free of any issues encountered during the entire research. Sensors with this design performed well as expected in lab long-term tests, and were deployed in the sensing probe of the final coal-gasifier field test. Sensor packaging and protection was improved through materials engineering through testing of packaging designs in two blank probe packaging tests at Eastman Chemical in Kingsport, TN. Performance analysis of the blank probe packaging resulted in improve package designs culminating in a 3rd generation probe packaging utilized for the full field test of the sapphire optical sensor and materials designed sensor packaging.

47 OTHER INSTRUMENTATION↗

Thin Film Packaging Solutions for High Efficiency OLED Lighting Products

The objective of the 'Thin Film Packaging Solutions for High Efficiency OLED Lighting Products' project is to demonstrate thin film packaging solutions based on SiC hermetic coatings that, when applied to glass and plastic substrates, support OLED lighting devices by providing longer life with greater efficiency at lower cost than is currently available. Phase I Objective: Demonstrate thin film encapsulated working phosphorescent OLED devices on optical glass with lifetime of 1,000 hour life, CRI greater than 75, and 15 lm/W. Phase II Objective: Demonstrate thin film encapsulated working phosphorescent OLED devices on plastic or glass composite with 25 lm/W, 5,000 hours life, and CRI greater than 80. Phase III Objective: Demonstrate 2 x 2 ft{sup 2} thin film encapsulated working phosphorescent OLED with 40 lm/W, 10,000 hour life, and CRI greater than 85. This report details the efforts of Phase III (Budget Period Three), a fourteen month collaborative effort that focused on optimization of high-efficiency phosphorescent OLED devices and thin-film encapsulation of said devices. The report further details the conclusions and recommendations of the project team that have foundation in all three budget periods for the program. During the conduct of the Thin Film Packaging Solutions for High Efficiency OLED Lighting Products program, including budget period three, the project team completed and delivered the following achievements: (1) a three-year marketing effort that characterized the near-term and longer-term OLED market, identified customer and consumer lighting needs, and suggested prototype product concepts and niche OLED applications lighting that will give rise to broader market acceptance as a source for wide area illumination and energy conservation; (2) a thin film encapsulation technology with a lifetime of nearly 15,000 hours, tested by calcium coupons, while stored at 16 C and 40% relative humidity ('RH'). This encapsulation technology was characterized as having less than 10% change in transmission during the 15,000 hour test period; (3) demonstrated thin film encapsulation of a phosphorescent OLED device with 1,500 hours of lifetime at 60 C and 80% RH; (4) demonstrated that a thin film laminate encapsulation, in addition to the direct thin film deposition process, of a polymer OLED device was another feasible packaging strategy for OLED lighting. The thin film laminate strategy was developed to mitigate defects, demonstrate roll-to-roll process capability for high volume throughput (reduce costs) and to support a potential commercial pathway that is less dependent upon integrated manufacturing since the laminate could be sold as a rolled good; (5) demonstrated that low cost 'blue' glass substrates could be coated with a siloxane barrier layer for planarization and ion-protection and used in the fabrication of a polymer OLED lighting device. This study further demonstrated that the substrate cost has potential for huge cost reductions from the white borosilicate glass substrate currently used by the OLED lighting industry; (6) delivered four-square feet of white phosphorescent OLED technology, including novel high efficiency devices with 82 CRI, greater than 50 lm/W efficiency, and more than 1,000 hours lifetime in a product concept model shelf; (7) presented and or published more than twenty internal studies (for private use), three external presentations (OLED workshop-for public use), and five technology-related external presentations (industry conferences-for public use); and (8) issued five patent applications, which are in various maturity stages at time of publication. Delivery of thin film encapsulated white phosphorescent OLED lighting technology remains a challenging technical achievement, and it seems that commercial availability of thin, bright, white OLED light that meets market requirements will continue to require research and development effort. However, there will be glass encapsulated white OLED lighting products commercialized in niche markets during the 2008 calendar year. This commercialization effort, the project team believes, will lead to increasing market attention and broader demand for more efficient, wide area general purpose white OLED lighting in the coming years.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Validation of measurements of ventilation-to-perfusion ratio inequality in the lung from expired gas

The analysis of the gas in a single expirate has long been used to estimate the degree of ventilation-perfusion (Va/Q) inequality in the lung. To further validate this estimate, we examined three measures of Va/Q inhomogeneity calculated from a single full exhalation in nine anesthetized mongrel dogs under control conditions and after exposure to aerosolized methacholine. These measurements were then compared with arterial blood gases and with measurements of Va/Q inhomogeneity obtained using the multiple inert gas elimination technique. The slope of the instantaneous respiratory exchange ratio (R slope) vs. expired volume was poorly correlated with independent measures, probably because of the curvilinear nature of the relationship due to continuing gas exchange. When R was converted to the intrabreath Va/Q (iV/Q), the best index was the slope of iV/Q vs. volume over phase III (iV/Q slope). This was strongly correlated with independent measures, especially those relating to inhomogeneity of perfusion. The correlations for iV/Q slope and R slope considerably improved when only the first half of phase III was considered. We conclude that a useful noninvasive measurement of Va/Q inhomogeneity can be derived from the intrabreath respiratory exchange ratio.

NASA Discipline Cardiopulmonary↗