SEARCH · Search NASA
Results for “Power modeling”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Experimental Characterization of an Electric Ducted Fan for the SUSAN 25% Scale Research Vehicle
An electric ducted fan (EDF) was tested in the NASA Langley 12-Foot Low-Speed Tunnel for the SUbsonic Single Aft eNgine (SUSAN) Electrofan 25% scale research vehicle, which incorporates distributed electric fans along the wings and serves as a scaled electrified transport aircraft testbed. The commercial-off-the-shelf EDF was selected as a propulsor that can meet the 25% scale vehicle geometry constraints, along with the performance requirements throughout the flight profile. The test included a series of one-factor-at-a-time (OFAT) and design of experiments (DOE) approaches that were implemented across a range of fan speed, voltage, freestream dynamic pressure, and incidence angle settings to characterize the performance of the EDF. Several test matrix designs and modeling approaches were considered. System identification methods were used to develop a static motor model, a dynamic motor model, an EDF thrust model, and a power consumption model. The model predictive capabilities were then evaluated with validation data not used in the modeling process. The results provide a comprehensive set of models developed to characterize the fan, and offer general insight into EDF modeling approaches.
Modeling and Analysis of Power Processing Systems
The feasibility of formulating a methodology for the modeling and analysis of aerospace electrical power processing systems is investigated. It is shown that a digital computer may be used in an interactive mode for the design, modeling, analysis, and comparison of power processing systems.
Lunar PMAD technology assessment
This report documents an initial set of power conditioning models created to generate 'ballpark' power management and distribution (PMAD) component mass and size estimates. It contains converter, rectifier, inverter, transformer, remote bus isolator (RBI), and remote power controller (RPC) models. These models allow certain studies to be performed; however, additional models are required to assess a full range of PMAD alternatives. The intent is to eventually form a library of PMAD models that will allow system designers to evaluate various power system architectures and distribution techniques quickly and consistently. The models in this report are designed primarily for space exploration initiative (SEI) missions requiring continuous power and supporting manned operations. The mass estimates were developed by identifying the stages in a component and obtaining mass breakdowns for these stages from near term electronic hardware elements. Technology advances were then incorporated to generate hardware masses consistent with the 2000 to 2010 time period. The mass of a complete component is computed by algorithms that calculate the masses of the component stages, control and monitoring, enclosure, and thermal management subsystem.
Wintertime Overnight NOx Removal in a Southeastern United States Coal-Fired Power Plant Plume: A Model for Understanding Winter NOx Processing and Its Implications
Nitric oxide (NO) is emitted in large quantities from coal-burning power plants. During the day, the plumes from these sources are efficiently mixed into the boundary layer, while at night, they may remain concentrated due to limited vertical mixing during which they undergo horizontal fanning. At night, the degree to which NO is converted to HNO3 and therefore unable to participate in next-day ozone (O3) formation depends on the mixing rate of the plume, the composition of power plant emissions, and the composition of the background atmosphere. In this study, we use observed plume intercepts from the Wintertime INvestigation of Transport, Emissions and Reactivity (WINTER) campaign to test sensitivity of overnight NOx removal to the N2O5 loss rate constant, plume mixing rate, background O3, and background levels of volatile organic compounds using a 2-D box model of power plant plume transport and chemistry. The factor that exerted the greatest control over NOx removal was the loss rate constant of N2O5. At the lowest observed N2O5 loss rate constant, no other combination of conditions converts more than 10 percent of the initial NOx to HNO3. The other factors did not influence NOx removal to the same degree.
Modeling of solar oscillation power spectra
To produce accurate estimates of the line-profile parameters of a model used to represent the spectral features in a solar oscillation power spectrum, it is necessary to (1) select the appropriate probability density function when deriving the maximum-likelihood function to be employed for the parameter estimation and (2) allow for the redistribution of spectral power caused by gaps in the data string. This paper describes a maximum-likelihood method for estimating the model parameters (based on the observed power spectrum statistics) that accounts for redistribution of spectral power caused by gaps in the data string, by convolving the model with the power spectrum of the observed window function. The accuracy and reliability of the method were tested using both artificial and authentic solar oscillation power spectrum data. A comparison of this method with various least-squares techniques is also presented.
A mathematical model of the maximum power density attainable in an alkaline hydrogen/oxygen fuel cell
A mathematical model of a hydrogen/oxygen alkaline fuel cell is presented that can be used to predict the polarization behavior under various power loads. The major limitations to achieving high power densities are indicated and methods to increase the maximum attainable power density are suggested. The alkaline fuel cell model describes the phenomena occurring in the solid, liquid, and gaseous phases of the anode, separator, and cathode regions based on porous electrode theory applied to three phases. Fundamental equations of chemical engineering that describe conservation of mass and charge, species transport, and kinetic phenomena are used to develop the model by treating all phases as a homogeneous continuum.
Model-Based Diagnosis in a Power Distribution Test-Bed
The Rodon model-based diagnosis shell was applied to a breadboard test-bed, modeling an automated power distribution system. The constraint-based modeling paradigm and diagnostic algorithm were found to adequately represent the selected set of test scenarios.
The NASA-JPL advanced propulsion program
The NASA Advanced Propulsion Concepts (APC) program at the Jet Propulsion Laboratory (JPL) consists of two main areas: The first involves cooperative modeling and research activities between JPL and various universities and industry; the second involves research at universities and industry that is directly supported by JPL. The cooperative research program consists of mission studies, research and development of ion engine technology using C-60 (Buckminsterfullerene) propellant, and research and development of lithium-propellant Lorentz-force accelerator (LFA) engine technology. The university/industry- supported research includes research (modeling and proof-of-concept experiments) in advanced, long-life electric propulsion, and in fusion propulsion. These propulsion concepts were selected primarily to cover a range of applications from near-term to far-term missions. For example, the long-lived pulsed-xenon thruster research that JPL is supporting at Princeton University addresses the near-term need for efficient, long-life attitude control and station-keeping propulsion for Earth-orbiting spacecraft. The C-60-propellant ion engine has the potential for good efficiency in a relatively low specific impulse (Isp) range (10,000 - 30,000 m/s) that is optimum for relatively fast (less than 100 day) cis-lunar (LEO/GEO/Lunar) missions employing near-term, high-specific mass electric propulsion vehicles. Research and modeling on the C-60-ion engine are currently being performed by JPL (engine demonstration), Caltech (C-60 properties), MIT (plume modeling), and USC (diagnostics). The Li-propellant LFA engine also has good efficiency in the modest Isp range (40,000 - 50,000 m/s) that is optimum for near-to-mid-term megawatt-class solar- and nuclear-electric propulsion vehicles used for Mars missions transporting cargo (in support of a piloted mission). Research and modeling on the Li-LFA engine are currently being performed by JPL (cathode development), Moscow Aviation Institute (engine testing), Thermacore (electrode development), as well as at MIT (plume modeling), and USC (diagnostics). Also, the mission performance of a nuclear-electric propulsion (NEP) Li-LFA Mars cargo vehicle is being modeled by JPL (mission analysis; thruster and power processor modeling) and the Rocketdyne Energy Technology and Engineering Center (ETEC) (power system modeling). Finally, the fusion propulsion research activities that JPL is supporting at Pennsylvania State University (PSU) and at Lawrenceville Plasma Physics (LPP) are aimed at far-term fast (less than 100 day round trip) piloted Mars missions and, in the very far term, interstellar missions.
Phosphoric acid fuel cell power plant system performance model and computer program
A FORTRAN computer program was developed for analyzing the performance of phosphoric acid fuel cell power plant systems. Energy mass and electrochemical analysis in the reformer, the shaft converters, the heat exchangers, and the fuel cell stack were combined to develop a mathematical model for the power plant for both atmospheric and pressurized conditions, and for several commercial fuels.
WEST-3 wind turbine simulator development. Volume 2: Verification
The details of a study to validate WEST-3, a new time wind turbine simulator developed by Paragib Pacific Inc., are presented in this report. For the validation, the MOD-0 wind turbine was simulated on WEST-3. The simulation results were compared with those obtained from previous MOD-0 simulations, and with test data measured during MOD-0 operations. The study was successful in achieving the major objective of proving that WEST-3 yields results which can be used to support a wind turbine development process. The blade bending moments, peak and cyclic, from the WEST-3 simulation correlated reasonably well with the available MOD-0 data. The simulation was also able to predict the resonance phenomena observed during MOD-0 operations. Also presented in the report is a description and solution of a serious numerical instability problem encountered during the study. The problem was caused by the coupling of the rotor and the power train models. The results of the study indicate that some parts of the existing WEST-3 simulation model may have to be refined for future work; specifically, the aerodynamics and procedure used to couple the rotor model with the tower and the power train models.
Modeling and analysis of Power Processing Systems
The paper deals with a NASA-sponsored, computer-based program Modeling and Analysis of Power Processing Systems (MAPPS). Three major MAPPS subprograms, Design Optimization, Control Design, and Performance Analysis are considered. The program makes it possible to reduce the design, analysis, and development time, and thus the cost, in achieving the required performance for power processing equipment and systems.
Modeling and Analysis of Power Processing Systems (MAPPS). Volume 1: Technical report
Computer aided design and analysis techniques were applied to power processing equipment. Topics covered include: (1) discrete time domain analysis of switching regulators for performance analysis; (2) design optimization of power converters using augmented Lagrangian penalty function technique; (3) investigation of current-injected multiloop controlled switching regulators; and (4) application of optimization for Navy VSTOL energy power system. The generation of the mathematical models and the development and application of computer aided design techniques to solve the different mathematical models are discussed. Recommendations are made for future work that would enhance the application of the computer aided design techniques for power processing systems.
Computer-Aided Modeling and Analysis of Power Processing Systems (CAMAPPS), phase 1
The large-signal behaviors of a regulator depend largely on the type of power circuit topology and control. Thus, for maximum flexibility, it is best to develop models for each functional block a independent modules. A regulator can then be configured by collecting appropriate pre-defined modules for each functional block. In order to complete the component model generation for a comprehensive spacecraft power system, the following modules were developed: solar array switching unit and control; shunt regulators; and battery discharger. The capability of each module is demonstrated using a simplified Direct Energy Transfer (DET) system. Large-signal behaviors of solar array power systems were analyzed. Stability of the solar array system operating points with a nonlinear load is analyzed. The state-plane analysis illustrates trajectories of the system operating point under various conditions. Stability and transient responses of the system operating near the solar array's maximum power point are also analyzed. The solar array system mode of operation is described using the DET spacecraft power system. The DET system is simulated for various operating conditions. Transfer of the software program CAMAPPS (Computer Aided Modeling and Analysis of Power Processing Systems) to NASA/GSFC (Goddard Space Flight Center) was accomplished.
Experimental study of sound power radiated from cold model jets and ground silencing arrangements, Volume I Technical report, Dec. 1962 - Jul. 1964
Radiated sound power conducted with cold model jets applied to acoustical problems and design of ground runup silencers for use with jet aircraft
Using color-color diagrams to test models for the 'blue bump'
Color-color diagrams are used to study the set of accretion disk plus power-law models and to determine whether they can adequately fit the optical/UV continua of a sample of 34 quasars, and the soft X-ray excesses measured for seven of the sample objects by Masnou et al. (1991). The loci of pure disk models for cos theta is greater than 0 are virtually superimposed on each other regardless of cos theta, demonstrating that a given observed spectrum cannot be described by a unique combination of S and cos theta. The distributions of model and data colors are found to overlap, showing that the disk plus power-law models do fit the distribution of data colors. For six of the seven objects, the soft X-ray excesses may be fit with an accretion disk plus power-law model without requiring the assumption of super-Eddington accretion; this shows the utility of employing Kerr disks.
Phase 2 and 3 wind tunnel tests of the J-97 powered, external augmentor V/STOL model
Static and forward speed tests were made in a 40 multiplied by 80 foot wind tunnel of a large-scale, ejector-powered V/STOL aircraft model. Modifications were made to the model following earlier tests primarily to improve longitudinal acceleration capability during transition from hovering to wingborne flight. A rearward deflection of the fuselage augmentor thrust vector was shown to be beneficial in this regard. Other augmentor modifications were tested, notably the removal of both endplates, which improved acceleration performance at the higher transition speeds. The model tests again demonstrated minimal interference of the fuselage augmentor on aerodynamic lift. A flapped canard surface also showed negligible influence on the performance of the wing and of the fuselage augmentor.
Assessment of the Impact of an Advanced Power System on a Turboelectric Single-Aisle Concept Aircraft
Electrified aircraft propulsion concepts show potential in using propulsion airframe inte-gration in order to increase efficiency in flight and therefore decrease fuel burn and emissions.Electrification offers component efficiency values greater than 90 percent, but the loss is in the form of low grade waste heat. A major challenge of electrified aircraft propulsion is managing that heat while minimizing any penalties associated with a thermal management system. This paper explores the effect of two innovations in the management of waste heat at the aircraft system level for a turboelectric single aisle concept. The first innovation is achieving a 3 times reduction in heat by developing high-efficiency components rather than managing the high levels of heat. The second takes advantage of the outer mold line of the aircraft to reject heat directly to the environment passively instead of adding active cooling loops that negatively impact the weight, power, and drag of the aircraft. In order to fully grasp the impact of the advanced power system, we develop methods of modeling the power and thermal management systems to be integrated in the full aircraft conceptual model. We then model the aircraft with a state of the art DC transmission system and active cooling loops as a baseline for our study. Our second model includes the advanced power system with active cooling, which results in a fuel burn reduction of 2.5 percent. Finally, in our third model we assess the benefit of an outer mold line cooling scheme with the advanced power system. The outer mold line cooling scheme with an advanced power system yields an additional 0.8 percent reduction in fuel burn,for an overall fuel burn reduction potential of 3.3 percent in addition to aerodynamic benefits of electrified aircraft propulsion.