Search NASA⌕ Search

SEARCH · Search NASA

Results for “REENTRY CONDITION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Laboratory prototype flash evaporator

A laboratory prototype flash evaporator that is being developed as a candidate for the space shuttle environmental control system expendable heat sink is described. The single evaporator configuration uses water as an evaporant to accommodate reentry and on-orbit peak heat loads, and Freon 22 for terrestrial flight phases below 120,000 feet altitude. The design features, fabrication techniques used for the prototype unit, redundancy considerations, and the fluid temperature control arrangement are reported in detail. The results of an extensive test program to determine the evaporator operational characteristics under a wide variety of conditions are presented.

Gaddis, J. L.↗
NASA NTRS1978

Supersonic flow over ablated nosetips using an unsteady, implicit numerical procedure

The axisymmetric supersonic flow over passive, that is, nonablating, indented nosetips of reentry vehicles is determined using an unsteady implicit numerical algorithm which solves either the inviscid Euler equations or the 'thin-layer' Navier-Stokes equations. A nonorthogonal independent variable transformation is used to map the distorted physical region, containing multiple zones of embedded subsonic flow into a rectangular computational domain at whose boundaries the required permeable or impermeable boundary conditions are simulated. Use of the implicit algorithm results in faster convergence to the steady state because of a larger allowable time step over conventional explicit schemes. The numerical results obtained compare favorably with existing experimental data for very mildly and severely indented blunt nosetips.

Kutler, P.↗
NASA NTRS1962

RE-ENTRY MATERIALS

The major requirement for a re-entry material is that it protect the vehicle from the aerodynamic heating associated with re-entry. A relatively short time ago, the term re-entry brought to mind a ballistic type trajectory and its characteristic heat pulse. Today, however, a variety of thermal re-entry conditions are common due to the various types of vehicles currently of interest. Extremes of re-entry heating-time conditions vary from the relatively low heat flux-long time pulse associated with glide and shallow orbital re-entries through high flux-short time ballistic re-entry to the very high heat flux-moderate time pulse associated with super orbital re-entry. Materials for providing thermal protection, therefore, vary considerably depending upon the type of reentry heat-time pulse. From a functional standpoint, thermal protection materials may be divided into two types; absorptive and radiative. The absorptive material dissipates heat by storage (heat sink) or mass transfer and chemical change (ablation, transpiration or sublimation).

Thermal protection↗
NASA NTRS1975

Solution of an optimal control lifting body entry problem by an improved method of perturbation functions

This paper presents a solution to a complex lifting reentry three-degree-of-freedom problem by using the calculus of variations to minimize the integral of the sum of the aerodynamics loads and heat rate input to the vehicle. The entry problem considered does not have state and/or control constraints along the trajectory. The calculus of variations method applied to this problem gives rise to a set of necessary conditions which are used to formulate a two point boundary value (TPBV) problem. This TPBV problem is then numerically solved by an improved method of perturbation functions (IMPF) using several starting co-state vectors. These vectors were chosen so that each one had a larger norm with respect to show how the envelope of convergence is significantly increased using this method and cases are presented to point this out.

Garcia, F., Jr.↗
NASA NTRS1980

Supersonic flow over three-dimensional ablated nosetips using an unsteady implicit numerical procedure

The three-dimensional supersonic flow over passive, that is, nonablating, indented nosetips of reentry vehicles is determined using an unsteady implicit numerical algorithm which solves either the inviscid Euler equations or the 'thin-layer' Navier-Stokes equations. A nonorthogonal independent variable transformation is used to map the distorted physical domain, containing multiple zones of embedded subsonic flow and separated flow regions into a rectangular computational volume at whose boundaries the required permeable or impermeable boundary conditions are simulated. Use of the implicit algorithm results in faster convergence to the steady state because of a larger allowable time step over conventional explicit schemes. The numerical results obtained compare favorably with existing numerical solutions and experimental data for simple spheres which validates the program. Results are also presented for analytically defined indented bodies for both laminar and turbulent flow conditions that demonstrate the program's capability for computing such flows.

Kutler, P.↗
NASA NTRS1984

Numerical computation of space shuttle orbiter flow field

The complete inviscid viscous real gas flow around the Space Shuttle Orbiter was computed. Real gas effects are important in predicting the reentry environment around the Orbiter because the high temperatures within the shock layer cause the air to dissociate and ionize, thus invalidating the perfect gas assumption. It is shown that real gas effects has a significant influence on the Orbiter aerodynamics. The approach utilizes a time dependent Navier-Stokes code to compute the subsonic nose portion of the flow field. This nose solution provides the initial conditions for the parabolized Navier-Stokes (PNS) code.

Tannehill, J. C.↗
NASA NTRS1993

Two-layer convective heating prediction procedures and sensitivities for blunt body reentry vehicles

This paper provides a description of procedures typically used to predict convective heating rates to hypersonic reentry vehicles using the two-layer method. These procedures were used to compute the pitch-plane heating distributions to the Apollo geometry for a wind tunnel test case and for three flight cases. Both simple engineering methods and coupled inviscid/boundary layer solutions were used to predict the heating rates. The sensitivity of the heating results in the choice of metrics, pressure distributions, boundary layer edge conditions, and wall catalycity used in the heating analysis were evaluated. Streamline metrics, pressure distributions, and boundary layer edge properties were defined from perfect gas (wind tunnel case) and chemical equilibrium and nonequilibrium (flight cases) inviscid flow-field solutions. The results of this study indicated that the use of CFD-derived metrics and pressures provided better predictions of heating when compared to wind tunnel test data. The study also showed that modeling entropy layer swallowing and ionization had little effect on the heating predictions.

Bouslog, Stanley A.↗
NASA NTRS1983

Non-intrusive flow measurements on a reentry vehicle

This study evaluates the utility of various non-intrusive techniques for the measurement of the flow field on the windward side of the Space Shuttle or a similar re-entry vehicle. Included are linear (Rayleigh, Raman, Mie, Laser Doppler Velocimetry, Resonant Doppler Velocimetry) and nonlinear (Coherent Anti-Stokes Raman, Laser Induced Fluorescence) light scattering, electron beam fluorescence, thermal emission and mass spectroscopy. Flow field properties are taken from a nonequilibrium flow model by Shinn, Moss and Simmonds at NASA Langley. Conclusions are, when possible, based on quantitative scaling of known laboratory results to the conditions projected. Detailed discussion with researchers in the field contributed further to these conclusions and provided valuable insights regarding the experimental feasibility of each of the techniques.

Miles, R. B.↗
NASA NTRS1986

An adaptive guidance algorithm for an aerodynamically assisted orbital plane change maneuver

Using analysis results from the post trajectory optimization program, an adaptive guidance algorithm is developed to compensate for density, aerodynamic and thrust perturbations during an atmospheric orbital plane change maneuver. The maneuver offers increased mission flexibility along with potential fuel savings for future reentry vehicles. Although designed to guide a proposed NASA Entry Research Vehicle, the algorithm is sufficiently generic for a range of future entry vehicles. The plane change analysis provides insight suggesting a straight-forward algorithm based on an optimized nominal command profile. Bank angle, angle of attack, and engine thrust level, ignition and cutoff times are modulated to adjust the vehicle's trajectory to achieve the desired end-conditions. A performance evaluation of the scheme demonstrates a capability to guide to within 0.05 degrees of the desired plane change and five nautical miles of the desired apogee altitude while maintaining heating constraints. The algorithm is tested under off-nominal conditions of + or -30% density biases, two density profile models, + or -15% aerodynamic uncertainty, and a 33% thrust loss and for various combinations of these conditions.

Blissit, J. A.↗
NASA NTRS1961

Piloted Simulator Tests of a Guidance System which Can Continously Predict Landing Point of a Low L/D Vehicle During Atmosphere Re-Entry

The guidance system for maneuvering vehicles within a planetary atmosphere which was studied uses the concept of fast continuous prediction of the maximum maneuver capability from existing conditions rather than a stored-trajectory technique. used, desired touchdown points are compared with the maximum range capability and heating or acceleration limits, so that a proper decision and choice of control inputs can be made by the pilot. In the method of display and control a piloted fixed simulator was used t o demonstrate the feasibility od the concept and to study its application to control of lunar mission reentries and recoveries from aborts.

Wingrove, Rodney C.↗
NASA NTRS1983

Evaluation of non-intrusive flow measurement techniques for a re-entry flight experiment

This study evaluates various non-intrusive techniques for the measurement of the flow field on the windward side of the Space Shuttle orbiter or a similar reentry vehicle. Included are linear (Rayleigh, Raman, Mie, Laser Doppler Velocimetry, Resonant Doppler Velocimetry) and nonlinear (Coherent Anti-Stokes Raman, Laser-Induced Fluorescence) light scattering, electron-beam fluorescence, thermal emission, and mass spectroscopy. Flow-field properties were taken from a nonequilibrium flow model by Shinn, Moss, and Simmonds at the NASA Langley Research Center. Conclusions are, when possible, based on quantitative scaling of known laboratory results to the conditions projected. Detailed discussion with researchers in the field contributed further to these conclusions and provided valuable insights regarding the experimental feasibility of each of the techniques.

Miles, R. B.↗
NASA NTRS2017

Computational Simulations of the NASA Langley HyMETS Arc-Jet Facility

The Hypersonic Materials Environmental Test System (HyMETS) arc-jet facility located at the NASA Langley Research Center in Hampton, Virginia, is primarily used for the research, development, and evaluation of high-temperature thermal protection systems for hypersonic vehicles and reentry systems. In order to improve testing capabilities and knowledge of the test article environment, an effort is underway to computationally simulate the flow-field using computational fluid dynamics (CFD). A detailed three-dimensional model of the arc-jet nozzle and free-jet portion of the flow-field has been developed and compared to calibration probe Pitot pressure and stagnation-point heat flux for three test conditions at low, medium, and high enthalpy. The CFD model takes into account uniform pressure and non-uniform enthalpy profiles at the nozzle inlet as well as catalytic recombination efficiency effects at the probe surface. Comparing the CFD results and test data indicates an effectively fully-catalytic copper surface on the heat flux probe of about 10% efficiency and a 2-3 kpa pressure drop from the arc heater bore, where the pressure is measured, to the plenum section, prior to the nozzle. With these assumptions, the CFD results are well within the uncertainty of the stagnation pressure and heat flux measurements. The conditions at the nozzle exit were also compared with radial and axial velocimetry. This simulation capability will be used to evaluate various three-dimensional models that are tested in the HyMETS facility. An end-to-end aerothermal and thermal simulation of HyMETS test articles will follow this work to provide a better understanding of the test environment, test results, and to aid in test planning. Additional flow-field diagnostic measurements will also be considered to improve the modeling capability.

Brune, A. J.↗
NASA NTRS1983

Effects of weightlessness on body composition in the rat

The effects of weightlessness on the body composition of rats were investigated using 5 male rats exposed to 18.5 days of weightlessness on the COSMOS 1129 biosatellite and killed after reentry. The animals were immediately dissected and the three major body divisions (musculoskeletal system, skin, and pooled viscera) were analyzed for fat, water, solids, and six elements. These results were determined as percentages of the fat-free body or its components and then compared with two groups of terrestrial controls, one of which was subjected to a flight simulation in a spacecraft mock-up while the other was under standard vivarium conditions. Compared with the control groups, the flight group was found to exhibit a reduced fraction of total body water, a net shift of body water from skin to viscera, a marked diminution in the fraction of extracellular water in the fat-free body, a marked reduction in the fraction of bone mineral, no change in the quantity of stored fat or adrenal masses, and a net increase in total muscle mass as indicated by total body creatine, protein, and body cell mass.

Pitts, G. C.↗
NASA NTRS1985

Monte Carlo simulations in support of the Shuttle upper atmospheric mass spectrometer experiment

This paper presents the results of calculations obtained with a Direct Simulation Monte Carlo (DSMC) method that describes both the external flow about the nose region of the Shuttle Orbiter and the internal flow in an inlet tube that provides the initial path between the shock-processed gases and a mass spectrometer mounted inside the Orbiter. A dedicated, three-dimensional version of the DSMC was developed during this study for the internal flow simulation along with the procedure for interfacing the external and internal flows. The calculations span the 140 to 95 km altitude range, which includes most of the hypersonic transitional flow encountered during reentry. All calculations were for a multicomponent gas mixture consisting of five chemical species while simulating the effects of transitional, rotational, vibrational, and chemical nonequilibrium. The results of the calculations show that within the entry region of the inlet tube where the gas has equilibrated with the sidewall tube temperature, the pressure is substantially less than the pressure at the external surface. This pressure correction for the entry region is significant for all conditions investigated and increases with altitude. The results highlight the structure of both the external and internal flow. Results of parametric studies show the sensitivity of the equilibrated inlet sidewall pressure to mass flow rates, gas-surface reflection model, tube side-wall temperature variations, and surface recombinations.

Moss, J. N.↗
NASA NTRS2003

Foam on Tile Impact Modeling for the Space Shuttle Program

Following the breakup of the Space Shuttle Columbia during reentry a NASA-wide investigation team was formed to examine the probable damage inflicted on Orbiter Thermal Protection System (TPS) elements by impact of External Tank insulating foam projectiles. Our team was to apply rigorous, physics-based analysis techniques to help determine parameters of interest for an experimental test program, utilize validated codes to investigate the full range of impact scenarios, and use analysis derived models to predict aero-thermal-structural responses to entry conditions. We were to operate on a non-interference basis with the j Team, and were to supply significant findings to that team and to the Orbiter Vehicle Engineering Working Group, being responsive to any solicitations for support from these entities. The authors formed a working sub-group within the larger team to apply the Smooth Particle Hydrodynamics code SPHC to the damage estimation problem. Numerical models of the LI-900 TPS tiles and of the BX-250 foam were constructed and used as inputs into the code. Material properties needed to properly model the tiles and foam were obtained from other working sub-groups who performed tests on these items for this purpose. Two- and three- dimensional models of the tiles were constructed, including the glass outer layer, the densified lower layer of LI-900 insulation, the Nomex felt Strain Isolation Pad (SIP) mounting layer, and the underlying aluminum 2024 vehicle skin. A model for the BX-250 foam including porous compression, elastic rebound, and surface erosion was developed. Code results for the tile damage and foam behavior were extensively validated through comparison with the Southwest Research Institute (SwRI) foam-on-tile impact experiments carried out in 1999. These tests involved small projectiles striking individual tiles and small tile arrays. Following code and model validation we simulated impacts of larger ET foam projectiles on the TPS tile systems used on the wings of the orbiter. Tiles used on the Wing Acreage, the Main Landing Gear Door, and the Carrier Panels near the front edge of the wing were modeled. Foam impacts shot for the CAB investigation were modeled, as well as impacts at larger angles, including rapid rotation of the projectile, and with varying foam properties. General results suggest that foam impacts on tiles at about 500 mph could cause appreciable damage if the impact angle is greater than about 20 degrees. Some variations of the foam properties, such as increased brittleness or increased density could increase damage in some cases. Rapid (17 rps) rotation failed to increase the damage for the two cases considered. This does not rule out other cases in which the rotational energy might lead to an increase in tile damage, but suggests that in most cases rotation will not be an important factor. Similar models will be applied for other impacting materials, other velocities, and other geometries as part of the Return to Flight process.

Stellingwerf, R. F.↗
NASA NTRS2013

Extension of a Kinetic Approach to Chemical Reactions to Electronic Energy Levels and Reactions Involving Charged Species With Application to DSMC Simulations

The ability to compute rarefied, ionized hypersonic flows is becoming more important as missions such as Earth reentry, landing high mass payloads on Mars, and the exploration of the outer planets and their satellites are being considered. Recently introduced molecular-level chemistry models that predict equilibrium and nonequilibrium reaction rates using only kinetic theory and fundamental molecular properties are extended in the current work to include electronic energy level transitions and reactions involving charged particles. These extensions are shown to agree favorably with reported transition and reaction rates from the literature for nearequilibrium conditions. Also, the extensions are applied to the second flight of the Project FIRE flight experiment at 1634 seconds with a Knudsen number of 0.001 at an altitude of 76.4 km. In order to accomplish this, NASA's direct simulation Monte Carlo code DAC was rewritten to include the ability to simulate charge-neutral ionized flows, take advantage of the recently introduced chemistry model, and to include the extensions presented in this work. The 1634 second data point was chosen for comparisons to be made in order to include a CFD solution. The Knudsen number at this point in time is such that the DSMC simulations are still tractable and the CFD computations are at the edge of what is considered valid because, although near-transitional, the flow is still considered to be continuum. It is shown that the inclusion of electronic energy levels in the DSMC simulation is necessary for flows of this nature and is required for comparison to the CFD solution. The flow field solutions are also post-processed by the nonequilibrium radiation code HARA to compute the radiative portion of the heating and is then compared to the total heating measured in flight.

Liechty, Derek S.↗
NASA NTRS1978

Optimum reentry trajectories of a lifting vehicle

The optimum maneuver of a space shuttle vehicle reentering a spherical, stationary, and locally exponential atmosphere was investigated. The use of Chapman's modified variables and a rescaled lift-drag polar leads to the formulation of a set of dimensionless equations of motion for flight analysis. The resulting equations are exact in the sense that they are also valid for flight in the vacuum. For planar flight several typical optimum maneuvers are investigated at different altitude ranges, low, moderate and very high. For three-dimensional flight, the procedure to solve the optimum trajectory for maximum cross range is discussed. Finally, using the equilibrium glide condition the maximum cross ranges for entry from circular speed, for several values of E*, and the footprint for E* = 1.5 are computed in this reduced problem.

Chern, J. S.↗
NASA NTRS2014

Extension of a Kinetic Approach to Chemical Reactions to Electronic Energy Levels and Reactions Involving Charged Species with Application to DSMC Simulations

The ability to compute rarefied, ionized hypersonic flows is becoming more important as missions such as Earth reentry, landing high mass payloads on Mars, and the exploration of the outer planets and their satellites are being considered. Recently introduced molecular-level chemistry models that predict equilibrium and nonequilibrium reaction rates using only kinetic theory and fundamental molecular properties are extended in the current work to include electronic energy level transitions and reactions involving charged particles. These extensions are shown to agree favorably with reported transition and reaction rates from the literature for near-equilibrium conditions. Also, the extensions are applied to the second flight of the Project FIRE flight experiment at 1634 seconds with a Knudsen number of 0.001 at an altitude of 76.4 km. In order to accomplish this, NASA's direct simulation Monte Carlo code DAC was rewritten to include the ability to simulate charge-neutral ionized flows, take advantage of the recently introduced chemistry model, and to include the extensions presented in this work. The 1634 second data point was chosen for comparisons to be made in order to include a CFD solution. The Knudsen number at this point in time is such that the DSMC simulations are still tractable and the CFD computations are at the edge of what is considered valid because, although near-transitional, the flow is still considered to be continuum. It is shown that the inclusion of electronic energy levels in the DSMC simulation is necessary for flows of this nature and is required for comparison to the CFD solution. The flow field solutions are also post-processed by the nonequilibrium radiation code HARA to compute the radiative portion.

Liechty, Derek S.↗