SEARCH · Search NASA

Results for “REYNOLDS NUMBER”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

All sources NASA NTRS DOE OSTI

NASA NTRS1998

Study of Low Reynolds Number Effects on the Losses in Low-Pressure Turbine Blade Rows

Experimental data from jet-engine tests have indicated that unsteady blade row interactions and separation can have a significant impact on the efficiency of low-pressure turbine stages. Measured turbine efficiencies at takeoff can be as much as two points higher than those at cruise conditions. Several recent studies have revealed that Reynolds number effects may contribute to the lower efficiencies at cruise conditions. In the current study numerical experiments have been performed to study the models available for low Reynolds number flows, and to quantify the Reynolds number dependence of low-pressure turbine cascades and stages. The predicted aerodynamic results exhibit good agreement with design data.

Ashpis, David E.↗

NASA NTRS1998

Study of Low Reynolds Number Effects on the Losses in Low-Pressure Turbine Blade Rows

Dorney, Daniel J.↗

NASA NTRS1987

A study of the effects of Reynolds number and Mach number on constant pressure coefficient jump for shock-induced trailing-edge separation

The influence of Mach and Reynolds numbers as well as airfoil and planform geometry on the phenomenon of constant shock jump pressure coefficient for conditions of shock induced trailing edge separation (SITES) was studied. It was demonstrated that the phenomenon does exist for a wide variety of two and three dimensional flow cases and that the influence of free stream Mach number was not significant. The influence of Reynolds number was found to be important but was not strong. Airfoil and planform geometric characteristics were found to be very important where the pressure coefficient jump was shown to vary with the sum of: (1) airfoil curvature at the upper surface crest, and (2) camber surface slope at the trailing edge. It was also determined that the onset of SITES could be defined as a function of airfoil geometric parameters and Mach number normal to the leading edge. This onset prediction was shown to predict the angle of onset to within + or - 1 deg accuracy or better for about 90% of the cases studied.

Cunningham, Atlee M., Jr.↗

NASA NTRS1979

Reynolds number effects on the turbulence field in compressible boundary layers

Detailed experiments were conducted in a zero pressure gradient, supersonic turbulent boundary layer, including measurements of the three components of velocity fluctuations and the turbulent shear stress, for Reynolds numbers ranging from 11.7 million to 105 million at a freestream Mach number of 2.3. The mean flow measurements established the fully developed and equilibrium nature of the boundary layer. Measurements of the turbulence field show that the vertical and transverse fluctuations are essentially equal throughout the boundary layer at all Reynolds numbers, a feature that is different from observations in incompressible flows. The data show that the boundary layer exhibits similarity in the turbulence profiles for the entire Reynolds number range and agrees with previous compressible and incompressible data using Morkovin's scaling to account for compressibility effects.

Acharya, M.↗

NASA NTRS1988

The effects of turbulence and stator/rotor interactions on turbine heat transfer. II - Effects of Reynolds number and incidence

Part I of this paper presents airfoil heat transfer data obtained in a rotating turbine model at its design rotor incidence. This portion of the paper presents heat transfer data obtained in the same model for various combinations of Reynolds number and inlet turbulence and for a very wide range of rotor incidence. On the suction surfaces of the first stage airfoils the locations and lengths of transition were influenced by both the inlet turbulence level and the Reynolds number. In addition it was demonstrated that on the first stage pressure surfaces combinations of high Reynolds number and high turbulence can produce heat transfer rates well in excess of two-dimensional turbulent flow. Rotor heat transfer distributions indicate that for relatively small deviations from the design incidence, local changes to the heat transfer distributions were produced on both pressure and suction sides near the stagnation region. For extremely large negative incidence the flow was completely separated from the rotor pressure surface producing very high local heat transfer.

Blair, M. F.↗

NASA NTRS1976

Numerical and approximate solution of the high Reynolds number small separation problem

Several possible methods of solving the small separation problem at high Reynolds number are investigated. In addition to using analytical methods, there are several numerical approaches which are used. High Reynolds number laminar two dimensional problems are used for simplicity. A brief discussion is given of the finite difference methods since these methods are discussed in detail. Most of the emphasis is placed on developing an approximate integral method. As a model problem the supersonic compression ramp problem is chosen since several numerical solutions along with experimental data are available. The techniques discussed are modified and applied to other similar type wall geometries.

Davis, R. T.↗

NASA NTRS1985

Vacuum chamber pressure effects on thrust measurements of low Reynolds number nozzles

Tests were conducted to investigate the effect of vacuum facility pressure on the performance of small thruster nozzles. Thrust measurements of two converging-diverging nozzles with an area ratio of 140 and an orifice plate flowing unheated nitrogen and hydrogen were taken over a wide range of vacuum facility pressures and nozzle throat Reynolds numbers. In the Reynolds number range of 2200 to 12 000 there was no discernable viscous effect on thrust below an ambient to total pressure ratio of 1000. In nearly all cases, flow separation occurred at a pressure ratio of about 1000. This was the upper limit for obtaining an accurate thrust measurement for a conical nozzle with an area ratio of 140.

Sovey, J. S.↗

NASA NTRS1986

Vacuum chamber pressure effects on thrust measurements of low Reynolds number nozzles

Tests were conducted to investigate the effect of vacuum facility pressure on the performance of small thruster nozzles. Thrust measurements of two converging-diverging nozzles with an area ratio of 140 and an orifice plate flowing unheated nitrogen and hydrogen were taken over a wide range of vacuum facility pressures and nozzle throat Reynolds numbers. In the Reynolds number range of 2200 to 12,000 there was no discernable viscous effect on thrust below an ambient to total pressure ratio of 1000. In nearly all cases, flow separation occurred at a pressure ratio of about 1000. This was the upper limit for obtaining an accurate thrust measurement for a conical nozzle with an area ratio of 140.

Sovey, J. S.↗

NASA NTRS1992

Boundary-layer measurements on a high Reynolds number three-element airfoil

An experimental investigation is being conducted to evaluate the boundary layer associated with a two-dimensional three-element single-flap airfoil at high Reynolds numbers. The present measurements are being made in the Langley Low-Turbulence (centerline turbulence intensity level is 0.034 percent at a Mach number of 0.2 and a total pressure of 60 psia) Pressure Tunnel (LTPT). The LTPT is a closed-circuit wind tunnel with a test section which is 3 ft wide, 7.5 ft high, and 7.5 ft long. Operating total pressure for the LTPT varies from 10 atmospheres to near-vacuum conditions. Tests are being conducted at a Mach number of 0.2 and Reynolds numbers (based on chord length) of 5, 9, and 16 million. Measurements include boundary-layer velocity surveys at several chordwise locations and surface skin-friction measurements using Preston tubes.

Selby, Gregory V.↗

NASA NTRS1989

Reynolds number effects on the transonic aerodynamics of a slender wing-body configuration

Aerodynamic forces and moments for a slender wing-body configuration are summarized from an investigation in the Langley National Transonic Facility (NTF). The results include both longitudinal and lateral-directional aerodynamic properties as well as slideslip derivatives. Results were selected to emphasize Reynolds number effects at a transonic speed although some lower speed results are also presented for context. The data indicate nominal Reynolds number effects on the longitudinal aerodynamic coefficients and more pronounced effects for the lateral-directional aerodynamic coefficients. The Reynolds number sensitivities for the lateral-directional coefficients were limited to high angles of attack.

Luckring, James M.↗

NASA NTRS2008

Compressible Boundary Layer Predictions at High Reynolds Number using Hybrid LES/RANS Methods

Simulations of compressible boundary layer flow at three different Reynolds numbers (Re(sub delta) = 5.59x10(exp 4), 1.78x10(exp 5), and 1.58x10(exp 6) are performed using a hybrid large-eddy/Reynolds-averaged Navier-Stokes method. Variations in the recycling/rescaling method, the higher-order extension, the choice of primitive variables, the RANS/LES transition parameters, and the mesh resolution are considered in order to assess the model. The results indicate that the present model can provide good predictions of the mean flow properties and second-moment statistics of the boundary layers considered. Normalized Reynolds stresses in the outer layer are found to be independent of Reynolds number, similar to incompressible turbulent boundary layers.

Choi, Jung-Il↗

NASA NTRS1986

Transition and separation control on a low-Reynolds number airfoil

The major problem associated with the aerodynamic performance of airfoils at low Reynolds numbers is the presence of extensive laminar boundary-layer separation resulting in a large increase in presssure drag and a decrease in lift. The rapid deterioration in airfoil characteristics can be largely eliminated by artificially controlling the flow through the introduction of suitable disturbances in the boundary layer such that transition occurs ahead of the anticipated laminar separation. This paper presents the results of wind-tunnel tests conducted on a 10-cm model of LRN (1)-1007 airfoil with passive (roughness trips) and active (acoustic excitation) controls to trigger transition and suppress separation. Significant improvements in the aerodynamic characteristics of the airfoil were observed. Results of this study for a chord Reynolds number range of 40,000 to 250,000 are presented in this paper.

Mangalam, S. M.↗

NASA NTRS1995

Development of a two-equation turbulence model for hypersonic flows: Evaluation of a low Reynolds number correction to the Kappa - epsilon two equation compressible turbulence model - Volume 1

The objective of the current research is the development of an improved k-epsilon two-equation compressible turbulence model for turbulent boundary layer flows experiencing strong viscous-inviscid interactions. The development of an improved model is important in the design of hypersonic vehicles such as the National Aerospace Plane (NASP) and the High Speed Civil Transport (HSCT). Improvements have been made to the low Reynolds number functions in the eddy viscosity and dissipation of solenoidal dissipation of the k-epsilon turbulence mode. These corrections offer easily applicable modifications that may be utilized for more complex geometries. The low Reynolds number corrections are functions of the turbulent Reynolds number and are therefore independent of the coordinate system. The proposed model offers advantages over some current models which are based upon the physical distance from the wall, that modify the constants of the standard model, or that make more corrections than are necessary to the governing equations. The code has been developed to solve the Favre averaged, boundary layer equations for mass, momentum, energy, turbulence kinetic energy, and dissipation of solenoidal dissipation using Keller's box scheme and the Newton spatial marching method. The code has been validated by removing the turbulent terms and comparing the solution with the Blasius solution, and by comparing the turbulent solution with an existing k-epsilon model code using wall function boundary conditions. Excellent agreement is seen between the computed solution and the Blasius solution, and between the two codes. The model has been tested for both subsonic and supersonic flat-plate turbulent boundary layer flow by comparing the computed skin friction with the Van Driest II theory and the experimental data of Weighardt; by comparing the transformed velocity profile with the data of Weighardt, and the Law of the Wall and the Law of the Wake; and by comparing the computed results of an adverse pressure gradient with the experimental data of Fernando and Smits. Good agreement is obtained with the experimental correlations for all flow conditions.

Knight, Doyle D.↗

NASA NTRS1938

The variation with Reynolds number of pressure distribution over an airfoil section

Pressures were simultaneously measured at 54 orifices distributed over the midspan section of a 5 by 30-inch rectangular model of the NACA 4412 airfoil in the variable-density tunnel. These measurements were made at 17 angles of attack from -20 degrees to 30 degrees for eight values of the effective Reynolds number form approximately 100,000 to 8,200,000. Accurate data were thus obtained for studying the variation of pressure distribution with Reynolds number. These results on the NACA 4412 section indicated that the pressure distribution is practically unaffected by changes in Reynolds number except where separation is involved.

Pinkerton, Robert M↗

NASA NTRS1990

The FX/90: A proposal in response to a low Reynolds Number station keeping mission

The FX/90 is a remotely piloted vehicle designed to fly at Reynolds numbers below 2 x 10 to the 5th power. Several applications exist for this type of flight, such as low altitude flight of very small aircraft. The design presented here allows investigation into the unique problems involved in low Reynolds number flight, which will, in turn, further understanding of this flight regime. The aircraft will operate in a steady flight environment, free from significant atmospheric turbulence and weather effects. The F-90 has a 39 in. fuselage which is constructed of balsa and plywood. The landing gear for the aircraft is a detachable carriage on which the aircraft rests. The aerodynamic planform is a rectangular wing (no taper or sweep) with a chord of 9 in., a wingspan of 72 in., and is constructed entirely out of styrofoam. The propulsion system is a puller configuration mounted on the front of the fuselage. It consists of an Astro 05 engine and a 10-6 two bladed propeller. Control of the aircraft is accomplished through the use of two movable control surfaces: elevators for pitch control, and a rudder for yaw control. The aircraft is soundly constructed, highly maneuverable, and adequately powered. Furthermore, the investigation into alternative technologies, most notably the styrofoam wing and the detachable landing gear, holds promise to improve the performance of the aircraft.

Wirthman, David↗

NASA NTRS1947

Two-Dimensional Wind-Tunnel Investigation of Modified NACA 65(sub 112)-111 Airfoil with 35-Percent-Chord Slotted Flap at Reynolds Numbers up to 25 Million

An investigation has been made in the Langley two-dimensional low-turbulence tunnels to develop the optimum configuration of a .035-chord slotted flap on an NACA 65(sub(112)-111 airfoil section modified by removing the trailing-edge cusp. Included in the investigation were measurements to determine the scale effects on the section lift and drag characteristics of the airfoil with the flap retracted for Reynolds numbers ranging from 3.0 X 10(exp 6) to 2.5 X 10(exp 6). The scale effects on the lift characteristics were also determined for the same reynolds numbers for the flap deflected in the rotation found to be optimum at a Reynolds number of 9.0 X 10(exp 6).

Racisz, Stanley F.↗

DOE OSTI2021

A machine learning-based interaction force model for non-spherical and irregular particles in low Reynolds number incompressible flows

In this study, interaction force of non-spherical particles in low Reynolds number gas-solid flow is investigated by neural network approaches. An artificial neural network (ANN) model is developed to correlate the non-spherical particle shape and the flow conditions with the interaction force. To define the particle shape, spherical harmonic expansion is applied. Furthermore, variational autoencoder model is then used to extract latent geometric features. The latent vector is utilized as an input with the Reynolds number for the ANN. The interaction force data, which is used as output data of the ANN, is obtained by particle resolved direct numerical simulation for 5200 non-spherical particles. The proposed model enables unsupervised extraction for non-spherical particle shapes and accurate predictions on the interaction force without heavy computation. This study provides the model that can explain complicated shapes of particles and be applied to a large scale, computational fluid dynamics simulation.

01 COAL, LIGNITE, AND PEAT↗

NASA NTRS1974

Longitudinal aerodynamic performance of a series of power-law and minimum wave drag bodies at Mach 6 and several Reynolds numbers

Experimental data have been obtained for two series of bodies at Mach 6 and Reynolds numbers, based on model length, from 1.4 million to 9.5 million. One series consisted of axisymmetric power-law bodies geometrically constrained for constant length and base diameter with values of the exponent n of 0.25, 0.5, 0.6, 0.667, 0.75, and 1.0. The other series consisted of positively and negatively cambered bodies of polygonal cross section, each having a constant longitudinal area distribution conforming to that required for minimizing zero-lift wave drag at hypersonic speeds under the geometric constraints of given length and volume. At the highest Reynolds number, the power-law body for minimum drag is blunter (exponent n lower) than predicted by inviscid theory (n approximately 0.6 instead of n = 0.667); however, the peak value of lift-drag ratio occurs at n = 0.667. Viscous effects were present on the bodies of polygonal cross section but were less pronounced than those on the power-law bodies. The trapezoidal bodies with maximum width at the bottom were found to have the highest maximum lift-drag ratio and the lowest mimimum drag.

Ashby, G. C., Jr.↗