SEARCH · Search NASA

Results for “ROTOR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

All sources NASA NTRS DOE OSTI

NASA NTRS2014

Tone and Broadband Noise Separation from Acoustic Data of a Scale-Model Contra-Rotating Open Rotor

Renewed interest in contra-rotating open rotor technology for aircraft propulsion application has prompted the development of advanced diagnostic tools for better design and improved acoustical performance. In particular, the determination of tonal and broadband components of open rotor acoustic spectra is essential for properly assessing the noise control parameters and also for validating the open rotor noise simulation codes. The technique of phase averaging has been employed to separate the tone and broadband components from a single rotor, but this method does not work for the two-shaft contra-rotating open rotor. A new signal processing technique was recently developed to process the contra-rotating open rotor acoustic data. The technique was first tested using acoustic data taken of a hobby aircraft open rotor propeller, and reported previously. The intent of the present work is to verify and validate the applicability of the new technique to a realistic one-fifth scale open rotor model which has 12 forward and 10 aft contra-rotating blades operating at realistic forward flight Mach numbers and tip speeds. The results and discussions of that study are presented in this paper.

Noise Separation↗

NASA NTRS2016

Isolated Open Rotor Noise Prediction Assessment Using the F31A31 Historical Blade Set

In an effort to mitigate next-generation fuel efficiency and environmental impact concerns for aviation, open rotor propulsion systems have received renewed interest. However, maintaining the high propulsive efficiency while simultaneously meeting noise goals has been one of the challenges in making open rotor propulsion a viable option. Improvements in prediction tools and design methodologies have opened the design space for next generation open rotor designs that satisfy these challenging objectives. As such, validation of aerodynamic and acoustic prediction tools has been an important aspect of open rotor research efforts. This paper describes validation efforts of a combined computational fluid dynamics and Ffowcs Williams and Hawkings equation methodology for open rotor aeroacoustic modeling. Performance and acoustic predictions were made for a benchmark open rotor blade set and compared with measurements over a range of rotor speeds and observer angles. Overall, the results indicate that the computational approach is acceptable for assessing low-noise open rotor designs. Additionally, this approach may be used to provide realistic incident source fields for acoustic shielding/scattering studies on various aircraft configurations.

Nark, Douglas M.↗

NASA NTRS2017

Investigation of Rotor-Airframe Interaction Noise Associated with Small-Scale Rotary-Wing Unmanned Aircraft Systems

In this study, hover acoustic measurements are taken on isolated rotor-airframe configurations representative of smallscale, rotary-wing unmanned aircraft systems (UAS). Each rotor-airframe configuration consists of two fixed-pitch blades powered by a brushless motor, with a simplified airframe geometry intended to represent a generic multicopter arm. In addition to acoustic measurements, CFD-based aeroacoustic predictions are implemented on a subset of the experimentally tested rotor-airframe configurations in an effort to better understand the noise content of the rotor-airframe systems. Favorable agreements are obtained between acoustic measurements and predictions, based on both time- and frequency-domain post-processing techniques. Results indicate that close proximity of airframe surfaces result in the generation of considerable tonal acoustic content in the form of harmonics of the rotor blade passage frequency (BPF). Analysis of the acoustic prediction data shows that the presence of the airframe surfaces can generate noise levels either comparable to or greater than the rotor blade surfaces under certain rotor tip clearance conditions. Analysis of the on-surface Ffowcs Williams and Hawkings (FW-H) source terms provide insight as to the predicted physical noise-generating mechanisms on the rotor and airframe surfaces.

Zawodny, Nikolas S.↗

NASA NTRS2019

Investigation of Anti-Phase Asymmetric Quiet Rotor Technology

The future of urban air mobility has a well-known tall pole challenge in the form of community acceptance which largely comes from the noise. This paper presents a proposed anti-phase rotor technology that could reduce noise sources such as blade vortex interaction noise. The anti-phase rotor technology includes a rotor design with various anti-phase alternating trailing edge patterns and a rotor design with an asymmetric blade tip. Four small-scale anti-phase rotors are fabricated by 3D printing for acoustic measurements conducted in a low-speed open-circuit wind tunnel to assess the effectiveness of the proposed anti-phase rotor technology. Preliminary test results appear to be promising and indicate that the anti-phase rotor designs could be a practical means of reducing blade vortex interactions and noise. The four tested anti-phase rotor designs have peak acoustic performance depending on the RPM and thrust which suggests improved performance through design optimization could be achieved for specific mission requirements.

Cramer, Nicholas B.↗

NASA NTRS2019

An Exploration of the Performance and Acoustic Characteristics of UAV-Scale Stacked Rotor Configurations

As interest grows in rotor- and propeller-driven electric vertical takeoff and landing (eVTOL) aircraft for the Urban Air Mobility market, there is a potential for previously studied concepts to reemerge due to the opportunities afforded by novel technologies and operating modes. One such concept is the “stacked” rotor, which consists of multiple co-rotating rotors positioned co-axially with a small axial offset. The goal of the work presented in this paper is to determine whether stacked rotors offer a compelling advantage for eVTOL aircraft in terms of both performance and acoustic characteristics. Results are presented for new experimental tests and computational modeling of multiple stacked rotor configurations, and comparisons are made with conventional rotor configurations. Testing of thirteen separate configurations— each using the same blade shape—revealed a configuration that resulted in an increase in the rotor power loading efficiency by more than 7% and reduced noise by more than 3 dBA when compared with a conventional rotor with all blades located in the same rotational plane.

Whiteside, Siena K. S.↗

DOE OSTI2026

Power performance and loads characterization of laboratory-scale cross-flow rotors fabricated using additive manufacturing

Tidal energy conversion is a relatively new application for additive manufacturing (AM), where the focus has been on fabricating axial-flow turbine blades. AM techniques add material precisely where it is needed, creating more complex shapes with less waste. Cross-flow rotor geometry presents an opportunity for AM to improve rotor performance by fabricating features that cannot be created economically via conventional manufacturing. The challenges associated with using AM in cross-flow design include water resistance and degradation over time while retaining a level of quality equivalent to conventionally machined parts. In this work, AM materials were tested by environmentally conditioning samples in a seawater tank for 5 months, followed by performance and phase-resolved load testing of laboratory-scale rotors in a hydraulic flume. We found that while metals like titanium and Inconel have excellent performance in marine environments, achieving the desired geometry and performance is difficult. Thermoplastics degraded in seawater but were easier to form into desired geometries and could exceed the performance of an aluminum control rotor. Warping and surface finish were significant detractors from AM rotor performance. These results suggest that the primary benefits of using AM for cross-flow rotors is to quickly fabricate and test unconventional rotor geometries.

16 TIDAL AND WAVE POWER↗

NASA NTRS2016

Parametric Investigation of the Effect of Hub Pitching Moment on Blade Vortex Interaction (BVI) Noise of an Isolated Rotor

At the most fundamental level, main rotor loading noise is caused by the harmonically-varying aerodynamic loads (acoustic pressures) exerted by the rotating blades on the air. Rotorcraft main rotor noise is therefore, in principle, a function of rotor control inputs, and thus the forces and moments required to achieve steady, or "trim", flight equilibrium. In certain flight conditions, the ensuing aerodynamic loading on the rotor(s) can result in highly obtrusive harmonic noise. The effect of the propulsive force, or X-force, on Blade-Vortex Interaction (BVI) noise is well documented. This paper presents an acoustics parametric sensitivity analysis of the effect of varying rotor aerodynamic pitch hub trim moments on BVI noise radiated by an S-70 helicopter main rotor. Results show that changing the hub pitching moment for an isolated rotor, trimmed in nominal 80 knot, 6 and 12 deg descent, flight conditions, alters the miss distance between the blades and the vortex in ways that have varied and noticeable effects on the BVI radiated-noise directionality. Peak BVI noise level is however not significantly altered. The application of hub pitching moment allows the attitude of the fuselage to be controlled; for example, to compensate for the uncomfortable change in fuselage pitch attitude introduced by a fuselage-mounted X-force controller.

Parametric Investigation↗

NASA NTRS2019

Isolated Rotor Forward Flight Testing at Martian Atmospheric Density Data Report

With the recent interest in Martian exploration using Unmanned Aerial Vehicles (UAVs), an experimental study was conducted to investigate rotor performance at Martian atmospheric conditions. Both simulation and testing of rotors is vital for evaluating rotor performance and behavior, especially for operations at Martian atmospheric densities and pressures. One critical test that has not been performed to date is helicopter forward flight testing at Martian atmospheric densities. To achieve this, a test was conducted in a tunnel facility that could be evacuated to the atmospheric pressure and density of Mars. A 40-inch-diameter rotor, roughly approximating the scale of the proposed Mars Helicopter (MH) design by the NASA Jet Propulsion Laboratory (JPL), was tested in forward flight at Mars’ atmospheric pressure at the NASA Ames Planetary Aeolian Laboratory (PAL). In this forward flight testing, the drive system of the Martian Surface Wind Tunnel (MARSWIT) was never turned on; all wind speeds read were generated either through the rotor spinning or from facility effects. The goal of this experiment was to collect rotor thrust, rotational speed, power, torque, and acoustics measurements. Subsequently, these results can be used for correlation with simulated cases using a mid-fidelity Computational Fluid Dynamics (CFD) simulation. As expected, rotor thrust and power are drastically reduced at air densities 100 times lower than at sea level on Earth. In addition, Reynolds number effects seem to play a vital role at reduced pressure that cannot be neglected in the simulation.

One Atmosphere↗

NASA NTRS2020

Model Rotor Hover Performance at Low Reynolds Number

Hover performance data from four key experiments has been analyzed in detail to shed some light on model rotor hover performance at low Reynolds number. Each experiment used the simplest blade geometry. The blades were constant chord and untwisted. Three experiments used blades with the NACA 0012 airfoil from root to tip. The NACA 0015 was used in the earliest test. The four experiments provide data spanning a Reynolds number range of 136,500 to 548,700. The specific objective of this report is to ask and answer two questions: 1. Does blade aspect ratio influence hover performance or is rotor solidity the fundamental rotor geometry parameter for practical engineering purposes? ANSWER: Rotor solidity is the fundamental rotor geometry parameter for practical engineering purposes. Any effect of blade aspect ratio appears to be such a secondary variable that its effect lies within the range of experimental error. 2. Is Reynolds number a significant factor in scaling up hover performance to full-scale rotor performance? The answer is twofold. ANSWER: (a) Reynolds number effects on the increase of power with thrust do not appear to be a significant factor for practical engineering purposes, and (b) Reynolds number effects on minimum profile power at or very near zero rotor thrust could not be clearly established primarily because the low torque levels could not be accurately measured with the test equipment used. This has led to significant data scatter. A number of other observations can be made based on the analysis provided herein. For instance: 1. The test matrices used in the four key references contained far too few data points. A collective pitch variation of four or five data points is insufficient to establish experimental accuracy and data repeatability. 2. A common property of the power-versus-thrust (raised to the 3/2 exponent) graphs was that this curve was linear below the onset of blade stall. 3. The blade-to-blade interference at or near zero thrust may, in fact, be creating a turbulent flow field such that the effective Reynolds number at a blade element is considerably greater than what theories using two-dimensional (2D) airfoil properties at a blade element would calculate. 4. Definitive experiments answering the two key questions have yet to be made.

Model Rotor Hover Performance↗

NASA NTRS2020

An Over-the-Rotor Liner Investigation with Configurations Enabled by Additive Manufacturing

This paper presents the results of an investigation of over-the-rotor acoustic liner configurations enabled by additive manufacturing. NASA Langley and Glenn Research Centers have collaborated on the usage of acoustic liners in the turbofan aircraft engine nacelle wall at or very near the tip of the rotor. These liners absorb rotor-alone and rotor-stator interaction noise and, due to their proximity to the rotor tips, serve as a pressure release to inhibit the amount of generated noise. Initial tests with a metallic foam liner demonstrated good acoustic results, but there was concern regarding the durability of the material. NASA then decided to explore configurations enabled by additive manufacturing via tests in the NASA Langley Normal Incidence Tube. Measured data for uniform-depth and variable-depth cores with narrow and wide chambers were compared with predictions via the NASA Langley impedance prediction model. As these configurations were intended for eventual use in an over-the-rotor application, it was necessary to add facesheets to the wide-chamber cores to avoid deleterious flow effects caused by open cavities. A number of facesheets were tested in combination with each wide-chamber core. Finally, it has been shown that grooves near the rotor tips cause an improvement in aerodynamic performance. A small set of grooves were fabricated such that they could be combined with the wide-chamber configurations. The results of these tests were subsequently used to guide designs for further testing in higher technology readiness level test rigs at NASA Glenn Research Center.

acoustic↗

NASA NTRSDate not supplied

Dragonfly Rotor Optimization using Machine Learning Applied to an OVERFLOW Generated Airfoil Database

NASA’s 4th New Frontiers Mission is the Titan Dragonfly relocatable lander. This coaxial quadrotor vehicle will be launched on a rocket to Titan in 2028. Following a gravity assisted Earth flyby and an approximate 6-year transit, Dragonfly will enter the Titan atmosphere around 2034 with the goal of exploring Titan’s pre-biotic chemistry and habitability. The multirotor design for this unique application has continually evolved since 2016 with constraints such as Titan’s cryogenic atmosphere at 95 Kelvin (-288 F), gravity 14% that of Earth’s, atmospheric density 440% of standard sea-level air, and the inability to test the entire system together under all these conditions until the first flight on Titan. This paper focuses on rotor design aspects of the Dragonfly lander and introduces a novel framework for multirotor design optimization considering multiple flight conditions. The methodology leverages machine learning methods and is demonstrated in the context of Dragonfly. A new OVERFLOW Machine Learning Airfoil Performance (PALMO) database is first presented. PALMO is then wrapped inside a Bayesian optimization framework and applied to a 4-rotor system (one side of the Dragonfly lander). Training data is generated on each iteration of the optimization using the CAMRAD-II comprehensive analysis software to evaluate successive rotor designs in multiple relevant flight conditions. An optimal design for the 4-rotor system was found with approximately 900 rotor designs analyzed in CAMRAD-II, which required 9 million queries of the PALMO surrogate models. This demonstration case evaluated 10,000,000 potential candidate rotor designs in 5.5 hours on 114 CPU cores using uniform inflow, and in 27.8 hours using the prescribed wake model. This work thus enables mid-fidelity rotor design optimization without requiring access to high-performance computing.

Dragonfly↗

NASA NTRSDate not supplied

Design and Optimization of an Open Rotor Stage

Open rotor propulsors enable greatly increased effective bypass ratios over current aircraft engines, resulting in significantly improved efficiencies. One of the most promising of these geometries is the “open fan”, which consists of a single rotor followed by a single stator. This configuration will be referred to as an “open rotor stage” for design work at NASA. In this work we consider the multidisciplinary design and optimization of an open rotor stage using a variety of 2D and 3D techniques. The 2D aerodynamic techniques used for design include a 2D Trefftz plane method, axisymmetric throughflow, and quasi-3D blade-to-blade CFD. Aerodynamic performance is prioritized, while structural requirements are met and some acoustic considerations are included. Between the rotor, stator, and hub profiles, a total of 101 design variables are used. Differences in the process of designing an open rotor stage vs. designing other high-speed propellers are also discussed. The current design, the NASA Optimized Propulsor for Efficiency and Noise (N-OPEN-1), achieves 84.7% net efficiency as predicted by 3D CFD, with further improvements expected to be possible. This design makes effective use of a slower rotor and a less tip-loaded work distribution than typical single-rotation propellers, allowing the stator to produce 14.8% of the thrust. Laminar flow on the blades was responsible for a 1.7% efficiency benefit and warrants further study.

Open rotors↗

NASA NTRS2026

Design and Optimization of an Open Rotor Stage

turbomachinery↗

NASA NTRS1972

Rotor systems research aircraft of predesign study. Volume 1: Summary and conclusions

The results are summarized of a study to develop a versatile research aircraft for flight testing a wide variety of advanced helicopter and compound rotor systems. The aircraft is required to accept these rotors with minimal changes in the basic vehicle. Rotors envisioned for testing include conventional rotors plus variable geometry, variable twist, variable diameter, coaxial, jet flap, circulation control, and slowed rotors. Various disc loadings would be accommodated. The aircraft must be configured to measure performance more accurately than past test vehicles. In addition, the aircraft would have a wing to off load the rotor while measuring performance during lightly loaded conditions. It would have variable drag and propulsive force so that the rotor can be tested while producing different values of horizontal force.

Linden, A. W.↗

NASA NTRS1972

The inclusion of rotor dynamics in controller design for helicopters.

State-feedback-controllers and state-estimators (filters) are designed for the roll-pitch-horizontal motions of a helicopter near hover, using a new quadratic synthesis technique. One model (tenth order) uses a dynamic model of the rotor, whereas the other model (sixth order) assumes the rotor can be tilted instantaneously. It is shown that, for tight control, neglecting the rotor dynamics in designing the autopilot can produce unstable closed-loop response on the model that includes rotor dynamics. Two filters are designed to use only fuselage sensors and two are designed to use both fuselage and rotor sensors. It is shown that rotor states can be estimated with sufficient accuracy using only fuselage sensors so that it does not seem worthwhile to use rotor sensors. The mean square response of the vehicle to a gusty, random wind, using several different filter/state-feedback compensators, is shown to be satisfactory.

Hall, W. E., Jr.↗

NASA NTRS1973

Noise comparison of two 1.2-pressure-ratio fans with 15 and 42 rotor blades

Two 1.829-m-(6-ft-) diameter fans suitable for a quiet engine for future short-takeoff-and-landing (STOL) aircraft were compared. Both fans were designed for a 1.2 pressure ratio with similar weight flows, thrusts, and tip speeds. The first fan, designated QF-9, had 15 rotor blades and 11 stator blades. The rotor was highly loaded and the tip solidity was less than 1. The QF-9 rotor blades had an adjustable pitch feature which can be used for thrust reversal. The second fan, designated QF-6, operated at a moderate loading with a rotor tip solidity greater than 1. Fan QF-6 had 42 rotor blades and 50 stator blades. The low number of rotor blades for QF-9 reduced the frequency of the blade-passage tone below the range of maximum annoyance. In addition to this difference, the QF-9 fan had a somewhat smaller rotor-stator separation than the QF-6 fan. In terms of sound pressure level and sound power level, QF-9 was the noisier fan, with the power level results for QF-9 being about 1 db above those for QF-6 at equivalent operating points as determined by similar stage pressure ratios. At the same equivalent operating points, the maximum perceived noise along a 152.5-m (500-ft) sideline for QF-9 was about 2.5 PNdb below that for QF-6, which indicated that QF-9 was less objectionable to human hearing.

Woodward, R. P.↗

NASA NTRS1974

Effect of damper on overall and blade-element performance of a compressor rotor having a tip speed of 1151 feet per second and an aspect ratio of 3.6

The overall and blade-element performance of two configurations of a moderately high aspect ratio transonic compressor rotor are presented. The subject rotor has conventional blade dampers. The performance is compared with a rotor utilizing dual wire friction dampers. At design speed the subject achieved a pressure ratio of 1.52 and efficiency of 0.89 at a near design weight flow of 72.1 pounds per second. The rotor with wire dampers gave consistently higher pressure ratios at each speed, but efficiencies for the two rotors were about the same. Stall margin for the subject rotor was 20.4 percent, but for the wire damped rotor only 4.0 percent.

Lewis, G. W.↗

NASA NTRS1973

Acoustic testing of a 1.5 pressure ratio low tip speed fan with a serrated rotor (QEP fan B scale model)

A scale model of the bypass flow region of a 1.5 pressure ratio, single stage, low tip speed fan was tested with a serrated rotor leading edge to determine its effects on noise generation. The serrated rotor was produced by cutting teeth into the leading edge of the nominal rotor blades. The effects of speed and exhaust nozzle area on the scale models noise characteristics were investigated with both the nominal rotor and serrated rotor. Acoustic results indicate the serrations reduced front quadrant PNL's at takeoff power. In particular, the 200 foot (61.0 m) sideline noise was reduced from 3 to 4 PNdb at 40 deg for nominal and large nozzle operation. However, the rear quadrant maximum sideline PNL's were increased 1.5 to 3 PNdb at approach thust and up to 2 PNdb at takeoff thust with these serrated rotor blades. The configuration with the serrated rotor produced the lowest maximum 200 foot (61.0 m) sideline PNL for any given thust when the large nozzle (116% of design area) was employed.

Kazin, S. B.↗