SEARCH · Search NASA
Results for “Range expansion”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Conversion of METL Diagnostic Flowmeters to Permanent Magnet Based Electromagnetic Flowmeters
The Mechanisms Engineering Test Loop (METL) uses three flowmeters to monitor sodium circulation through the main loop, the Cold Trap leg, and the Plugging Meter leg. When constructed, the Cold Trap flowmeter (CTFM) and Plugging Meter flowmeter (PMFM) were equipped with permanent magnets and Hall Sensors. By October of 2019, during normal operations, both the CTFM and PMFM failed, producing either erroneous or zero signals. Repairs to the flowmeters were attempted in January of 2020 but failed to resolve the issues. Therefore, starting in March of 2021, a plan was developed to convert the installed flowmeters to more robust permanent magnet based electromagnetic flowmeters (EMFMs). The Cold Trap EMFM (CT EMFM) and Plugging Meter EMFM (PM EMFM) were fully installed by August of 2021. Initial testing and commissioning were completed in November of 2021. Finally, the first calibration runs were finished in March of 2022. This report discusses the design, conversion, and calibration of the as-built CTFM and PMFM to robust permanent magnet based EMFMs. During the design phase, theoretical models were used to estimate the signal output and required magnet sizes. Then, the CTFM and PMFM were disassembled and converted to EMFMs. After commissioning, the CT EMFM and PM EMFM were calibrated using a ‘Time Transfer Procedure’ carried out with METL Expansion Vessels and Test Vessel Two. The accuracy of the calibration was estimated through an uncertainty analysis. Finally, the report describes some lessons learned for future flowmeter conversions and follow-up work. In total, both METL EMFM’s met the desired performance targets. Testing data showed that the METL EMFMs provide a output signal of roughly 2 mV at 1 GPM and 250 °C. During calibration, flowrates between 0.7 GPM and 2.4 GPM were achieved. In this flow range, calibration coefficients of 0.485 and 0.935 were measured as with errors ranging from 15-5% and 16-5% for the CT EMFM and PM EMFM, respectively. Above 1.5 GPM, the error was assumed to be about 5% for both METL EMFMs. Several points will be considered for future follow-up work on the METL EMFM’s. First, the signal noise issues in the PM EMFM will be addressed. It is likely the source of the noise is due to some stray EMF from a heater. Secondly, the NdFeB magnets will be replaced with a grade that has a Curie temperature above 80 °C. For example, a few grades of NeFeB magnets have Curie temperatures which exceed 150 °C and some SmCo magnets have Curie temperatures as high as 500 °C. Third, more calibration runs will be completed in the range of 0.5-2.5 GPM. This will further improve the accuracy of the calibration coefficient. Fourth, calibration runs will be completed up to 5 GPM. This requires a larger pressure relief valve to be installed on the Expansion Vessel and Test Vessel 2, as well as a revised calibration procedure. Lastly, calibration runs will be completed to account for cold spots in the system, which reduced the inlet temperature of the METL EMFMs. Overall, these points will improve the calibration coefficients derived in this work and also improve the performance of the METL EMFMs.
Construction of 3D MHD pressure drop correlation and flow characterization in the contraction region of a fusion blanket manifold
Inlet and outlet manifolds are typical components of liquid metal (LM) blanket designs of a fusion power reactor to be used to distribute the LM flow into breeding channels and collect it at the exit of the blanket. High pressure loss in the magnetohydrodynamic (MHD) flows featuring abrupt geometrical changes is one of the main feasibility issues of such designs. Recently, optimization studies were conducted to construct 3D MHD pressure drop correlations for a LM flow in an electrically insulating manifold with gradual expansion. Here, the 3D computational approach developed in that study is applied to the outlet manifold featuring gradual contraction. A systematic analysis was performed with a total number of 135 flow cases computed with COMSOL Multiphysics for Hartmann numbers 1000 < Ha < 10,000, Reynolds numbers 100 < Re < 12,000, and contraction angles 45° < θ < 75° for a fixed contraction ratio of 4. The effects of Ha, Re and θ on the flow recirculation, development length and the total pressure drop were carefully examined. A linear regression analysis was used to determine the power rule of pressure drop coefficient k related to Ha and Re, demonstrating a good match with the Ludford layer theory. Eventually, a correlation for the 3D MHD pressure drop coefficient was constructed as a function of Ha, Re and θ. Further, the results were compared against the inlet manifold. It was found that the flow in the inlet manifold exhibits larger recirculation zones. In the investigated range of Ha, Re and θ, the pressure drop coefficient k of the LM MHD flow in the gradual contraction is only slightly lower (< 8 %) than that in the gradual expansion.
Mechanical and Thermophysical properties of low enriched uranium-10wt% molybdenum rolled foils
In this study, low-enriched (~19.75% 235 U) U-10Mo(wt%) foils were evaluated for both mechanical and thermophysical properties to establish baseline characteristics prior to irradiation testing. Cast U-10Mo ingots were sequentially hot and cold rolled to two different final foil thicknesses, resulting in different levels of cold work being present in the finished foils. The mechanical response of the U-10Mo foils was evaluated in the temperature range of 293–623 K. Increasing test temperatures resulted in decreases of both yield and ultimate tensile strength. Comparison of results to earlier work performed on depleted U-10Mo rolled foils indicates that the material in this study has lower strength and increased ductility. However, a comparison of the two different foil thicknesses in this study found that they were nearly identical in yield and ultimate tensile strength, differing by only 10–20 MPa (<2%). Thermal conductivity was calculated from the measurements of specific heat, linear thermal expansion, and thermal diffusivity from 323 to 1273 K on both thicknesses of the foils. These data were approximately 5–10% lower than previously published data above 573 K and were similar to data for temperature ranges below 573 K. Differences are likely related to differences in grain size and/or impurity content and variation in fabrication history.
Efficient machine learning interatomic potentials robust for liquid and multiple solid polymorphs of NaF and KF
Achieving atomic-level understanding of crystallization of molten salts is of importance to a wide range of technological applications. Recent work [Fan et al., Proc. Natl. Acad. Sci. USA 122, e2425702122 (2025)] revealed that crystal nucleation in molten LiF salt is a multistage process according to the molecular-dynamics (MD) simulations based on an atomic cluster expansion (ACE) machine-learning interatomic potential (MLIP). In order to understand the influence of increasing cation size on nucleation pathways and nucleation rates of molten fluoride salts, here we develop two new ACE MLIPs for NaF and KF. The two ACE MLIPs feature DFT-SCAN-level accuracy for liquid and multiple solid polymorphs over a wide temperature (0–2000 K) and pressure (0–100 GPa) range, and also reproduce well a number of experimental data for solid and liquid equilibrium properties. The efficiency of the two ACE MLIPs enable million-atom-scale or microsecond-scale MD simulations. The two general-purpose ACE MLIPs are expected to be useful for atomistic simulations for different purposes, in addition to studying crystallization of molten NaF and KF salts.
Helium Incorporation into Scandium Fluoride, a Model Negative Thermal Expansion Material
Scandium trifluoride is a model negative thermal expansion (NTE) material. Its simple structure can be described as an A-site vacant perovskite, and it shows isotropic NTE over a very wide temperature range (up to ~1100 K), due to transverse vibrational motion of the fluoride. Like many framework NTE materials, it undergoes a phase transition at low pressures, adopting a rhombohedral (R3̅c) structure at >0.7 GPa and 300 K in commonly used nonpenetrating pressure media, such as silicone oil. High pressure X-ray diffraction data and gas uptake/release measurements indicate that, on compression in helium above ~200 K, helium is inserted into ScF 3 to form the defect perovskite He x ScF 3 . The incorporation of helium stiffens the structure and changes its phase behavior. At room temperature, complete filling of the structure with helium does not occur until >1.5 GPa. On compression, a cubic perovskite structure is maintained until ~5 GPa. As the pressure was increased to ~9.5 GPa, a further transition occurred at ~7 GPa. The first transition at ~5 GPa is likely to a tetragonal (P4/mbm) perovskite, but the detailed structure of the perovskite phase formed on compression above ~7 GPa is unclear. Cooling down from 300 to 100 K in helium at ~0.4 GPa leads to an approximate composition of He 0.1 ScF 3 . High pressure neutron diffraction measurements, in the temperature range 15–150 K show that the incorporation of helium increases the pressure at which the cubic (Pm3̅m) to rhombohedral (R3̅c) putative quantum structural phase transition occurs from close to 0 GPa to ~0.2 GPa at 0 K.
Polyethylene Glycol Crowder’s Effect on Enzyme Aggregation, Thermal Stability, and Residual Catalytic Activity
Protein stability and performance in various natural and artificial systems incorporating many other macromolecules for therapeutic, diagnostic, sensor, and biotechnological applications attract increasing interest with the expansion of these technologies. Here we address the catalytic activity of lysozyme protein (LYZ) in the presence of a polyethylene glycol (PEG) crowder in a broad range of concentrations and temperatures in aqueous solutions of two different molecular mass PEG samples (Mw = 3350 and 10000 g/mol). The phase behavior of PEG–protein solutions is examined by using dynamic light scattering (DLS) and small-angle X-ray scattering (SAXS), while the enzyme denaturing is monitored by using an activity assay (AS) and circular dichroism (CD) spectroscopy. Molecular dynamic (MD) simulations are used to illustrate the effect of PEG concentration on protein stability at high temperatures. The results demonstrate that LYZ residual activity after 1 h incubation at 80 °C is improved from 15% up to 55% with the addition of PEG. The improvement is attributed to two underlying mechanisms. (i) Primarily, the stabilizing effect is due to the suppression of the enzyme aggregation because of the stronger PEG–protein interactions caused by the increased hydrophobicity of PEG and lysozyme at elevated temperatures. (ii) The MD simulations showed that the addition of PEG to some degree stabilizes the secondary structures of the enzyme by delaying unfolding at elevated temperatures. The more pronounced effect is observed with an increase in PEG concentration. This trend is consistent with CD and AS experimental results, where the thermal stability is strengthened with increasing of PEG concentration and molecular mass. Overall, the results show that the highest stabilizing effect is approached at the critical overlap concentration of PEG.
Ab initio study of short-range ordering in vanadium-based disordered rocksalt structures
Disordered rocksalt Li-excess (DRX) compounds are attractive new cathode materials for Li-ion batteries as they contain resource-abundant metals and do not require the use of cobalt or nickel. Understanding the delithiation process and cation short-range ordering (SRO) in DRX compounds is essential to improve these promising cathode materials. Herein, we use first-principles calculations along with the cluster-expansion approach to model the disorder in DRX Li 2-x VO 3 , 0 < x < 1. We discuss the SRO of Li in tetrahedral and octahedral sites, and the order in which Li delithiates and V oxidizes with respect to local environments. We reveal that the number of nearest-neighbor V dictates the order of delithiation from octahedral sites and that V is oxidized in a manner that minimizes the electrostatic interactions among V. In conclusion, our results provide valuable insight for tailoring the performance of V-based DRX cathode materials in general by controlling the SRO features that reduce energy density.
Investigation of high field plasma dynamics in a laser-produced plasma expanding into a background gas
This paper presents an overview of experimental results of a laser-produced plasma expanding into a background gas, immersed within a large range of highly uniform magnetic fields (of up to 3 T), that are transverse to the expanding plasma. We used intensified gated imaging to capture the expansion of the plasma across and along the magnetic field lines to observe the spatiotemporal expansion dynamics for different magnetic field strengths. We observe changes in the perpendicular and parallel dynamics of the laser-produced plasmas expansion at high magnetic field. In addition, our results have also indicated the presence of electron-ion hybrid instabilities at relatively high pressures (100 mTorr) and relatively high magnetic field strengths (2 T), in accordance with theoretical calculations.
Simulation of PV Variability as a Function of PV Generation and Plant Size
The deployment of photovoltaic (PV) systems continues to show significant expansion; however, this growth has brought added attention to issues around the variability of the solar resource. Both spatial and temporal variability exist. Temporal scales can range from the sub-second to multiyear, whereas spatial scales can range from a few meters to tens of kilometers. There are multiple methods described in the literature to quantify PV variability at various spatial and temporal scales. This study focuses on short-term temporal variability and uses similar approaches with the addition of PV plant size a parameter to quantify variability. The method employed here incorporates the normalization of clear-and cloudy-sky conditions and PV plant size to quantify nominal variability metrics. The distribution and fluctuations of these metrics provide relevant information that is useful for system operations. The National Solar Radiation Database (NSRDB) is used to simulate PV variability as a function of PV generation and plant size. Hypothetical but realistic system information at 33 locations is used to model PV generation by feeding NSRDB solar irradiance data to the National Renewable Energy Laboratory’s System Advisor Model (SAM). Over the selected region, it is found that the aggregated ramp rates for the 1-minute data are associated with standard deviations ranging from 0.002–0.055 on a daily basis; however, hourly intervals induce higher aggregated ramp rates than the other timescales. Even though minute-to-minute variations are significant for the 1-minute time-scale, the standard deviation aggregated into a daily metric is smaller because of the cancellation of values.
Simulation of PV Variability as a Function of PV Generation and Plant Size: Preprint
The deployment of photovoltaic (PV) systems continues to show significant expansion; however, this growth has brought added attention to issues around the variability of the solar resource. Both spatial and temporal variability exist. Temporal scales can range from the sub-second to multiyear, whereas spatial scales can range from a few meters to tens of kilometers. There are multiple methods described in the literature to quantify PV variability at various spatial and temporal scales. This study focuses on short-term temporal variability and uses similar approaches with the addition of PV plant size a parameter to quantify variability. The method employed here incorporates the normalization of clear- and cloudy-sky conditions and PV plant size to quantify nominal variability metrics. The distribution and fluctuations of these metrics provide relevant information that is useful for system operations. The National Solar Radiation Database (NSRDB) is used to simulate PV variability as a function of PV generation and plant size. Hypothetical but realistic system information at 33 locations is used to model PV generation by feeding NSRDB solar irradiance data to the National Renewable Energy Laboratory’s System Advisor Model (SAM). Over the selected region, it is found that the aggregated ramp rates for the 1-minute data are associated with standard deviations ranging from 0.002–0.055 on a daily basis; however, hourly intervals induce higher aggregated ramp rates than the other timescales. Even though minute-to-minute variations are significant for the 1-minute timescale, the standard deviation aggregated into a daily metric is smaller because of the cancellation of values.
Assessment of MOOSE-Based Tools for Calculating Radial Core Expansion
Radial core expansion in liquid-metal cooled fast reactor systems is a well-known phenomenon that produces strong reactivity feedback effects. An inherently safe reactor design takes advantage of negative reactivity feedback in accident scenarios by utilizing a core restraint system which produces a bowed shape that allows for radial expansion of the fuel regions. Detailed modeling and simulation of core radial expansion itself as well as subsequent reactivity feedback is a challenging task involving contact of many fuel assembly elements and physics feedback from neutronics, thermal hydraulics, and thermal mechanical response. A variety of physics codes have been developed to model aspects of radial core expansion but in general invoke geometrical or physics approximations. No code system currently exists which tightly and robustly couples these physics with enough detail to fully resolve the complex core radial expansion reactivity feedback effects. The future availability of such a code system is of vital importance to fully understanding the reactivity feedback effects that occur due to radial expansion, and consequently to optimizing the design of the core restraint system. A high-fidelity code will also be used to benchmark existing lower fidelity, faster running models to understand their benefits, limitations, and range of applications. A code development path using MOOSE-based tools is proposed in order to leverage the detailed geometry capabilities and natural tight coupling and robustness of MOOSE-based applications for modeling this complex phenomena. While simulation of the full phenomenon involves several physics, an assessment has been initiated on the capabilities and readiness of the currently available Tensor Mechanics module within MOOSE for calculation of the structural mechanical responses which occur within the reactor core. This report focuses on modeling the force-deformation response which mimics the physics of a duct contact deformation, as well as differential thermal expansion which produces a thermal bowed shaped for the fuel assemblies in a core. Simple examples were initially performed such as simple supported beam bending under load. The complexity of examples was progressively increased to better mimic the duct behavior by including a differential thermal example and inclusion of hexagonal cross-sections in the geometry. Further assessment of the structural mechanical response simulation capability is still required for modeling duct contact interactions and irradiation creep and swelling. Companion thermal hydraulic and neutronics assessments will also be required; these activities are planned for future years. Finally, integration of the multiple physics components through MOOSE is required to predict the core radial expansion and subsequent feedback effects.
GRIDCERF - Geospatial Raster Input Data for Capacity Expansion Regional Feasibility
The Geospatial Raster Input Data for Capacity Expansion Regional Feasibility (GRIDCERF) data package is a high-resolution product to evaluate siting suitability for renewable and non-renewable power plants in the conterminous United States. GRIDCERF offers hundreds of individual suitability layers for use with both renewable and non-renewable power plant technology configurations in a harmonized format that can be easily ingested by geospatially-enabled modeling software. It also provides pre-compiled technology-specific suitability layers and allows for user customization to robustly address science objectives when evaluating varying future conditions. GRIDCERF data can be directly used with the CERF (Capacity Expansion Regional Feasibility) model to site power plants at a 1km resolution. GRIDCERF includes composite technology siting suitability raster layers for the following utility scale technology configurations. Note that, in addition to technology sub-types shown below, various cooling types are also included (recirculating, pond, once-through, recirculating-seawater, dry-hybrid, or dry) for various technologies. Biomass Conventional (with or without CCS) IGCC (with or without CCS) Coal Conventional (with or without CCS) IGCC (with or without CCS) Natural Gas Combined-cycle (CC) (with or without CCS) Turbine Geothermal Enhanced Geothermal Systems (EGS) - Class 1 through Class 5 resource potential Nuclear Gen 2 Light Water Reactor (LWR) Gen 3 Small Modular Reactor (SMR) Gen 3 AP1000 Refined Liquids Combined-cycle (CC) (with or without CCS) Turbine Solar Photovoltaic (PV) - for capacity factors in the range of 6-18% Utility-scale Concentrating Solar Power (CSP) - for capacity factors in the range of 24-46% Tower Wind (Onshore) - for capacity factors in the range of 5-50% 80m hub height 100m hub height 120m hub height 140m hub height Wind (Offshore) - for capacity factors in the range of 25-60% 100m hub height 140m hub height 160m hub height
Likelihood Maximization and Moment Matching in Low SNR Gaussian Mixture Models
We derive an asymptotic expansion for the log-likelihood of Gaussian mixture models (GMMs) with equal covariance matrices in the low signal-to-noise regime. The expansion reveals an intimate connection between two types of algorithms for parameter estimation: the method of moments and likelihood optimizing algorithms such as Expectation-Maximization (EM). We show that likelihood optimization in the low SNR regime reduces to a sequence of least squares optimization problems that match the moments of the estimate to the ground truth moments one by one. This connection is a stepping stone towards the analysis of EM and maximum likelihood estimation in a wide range of models. A motivating application for the study of low SNR mixture models is cryo-electron microscopy data, which can be modeled as a GMM with algebraic constraints imposed on the mixture centers. We discuss the application of our expansion to algebraically constrained GMMs, among other example models of interest. © 2022 The Authors. Communications on Pure and Applied Mathematics published by Wiley Periodicals LLC.
Improved thermal resummation for multi-field potentials
The resummation of large thermal corrections to the effective potential is mandatory for the accurate prediction of phase transitions. We discuss the accuracy of different prescriptions to perform this resummation at the one- and two-loop level and point out conceptual issues that appear when using a high-temperature expansion at the two-loop level. Moreover, we show how a particular prescription called partial dressing, which does not rely on a high-temperature expansion, consistently avoids these issues. We introduce a novel technique to apply this resummation method to the case of multiple mixing fields. Our approach significantly extends the range of applicability of the partial dressing prescription, making it suitable for phenomenological studies of beyond the Standard Model extensions of the Higgs sector.
Thermophysical properties and reversible phase transitions in yttrium hydride
In this study, the thermophysical properties of yttrium hydrides were investigated as a function of temperature (room temperature [RT] to 700°C) and hydrogen concentration (H/Y ratio ranges from 1.52 to 1.93). The results indicate that at the temperatures below 300°C, the hydrogen content did not have a significant influence on the thermal expansion, while the specific heat capacity, the thermal diffusivity, and the calculated thermal conductivity were slightly higher for the larger H/Y ratio. Between 300°C and 700°C, a reversible second-order endothermic transition in all measured thermal properties was observed. It was also found that the onset temperatures of the observed transition varied, with the composition having inverse dependence on the hydrogen content. The phase transition from ( α - Y + δ -YH x ) mixed phase to the δ -YH x single phase was excluded from the main contributors to the observed transition. An attempt was made to explain the behavior of the thermophysical properties at higher temperatures by considering the order–disorder transition as a result of hydrogen redistribution.
Physical and Thermomechanical Properties of Yttrium Hydride from Large Scale Bulk Metal Hydriding Furnace
Given the superior thermal stability and highly attainable hydrogen density, yttrium hydride is an excellent high-temperature moderator material in advanced thermal neutron spectrum reactors that require small core volumes. Yttrium hydride has been selected as the moderator material for the Transformational Challenge Reactor, which was launched at Oak Ridge National Laboratory (ORNL) in 2019. However, fabrication of large-scale crack-free yttrium hydride is challenging and very limited efforts have been committed to the characterization of bulk yttrium hydride in response to the need to establish a complete database of the thermomechanical properties of YHx. In this report, the challenges associated with fabricating large-scale crack-free yttrium hydride are discussed herein. In response to those challenges, a hydriding system was designed and constructed at ORNL and was used to successfully fabricate crack-free yttrium hydride in complex geometries at large scales. This was accomplished by precisely controlling the hydrogen’s partial pressure and the retort temperature, which was informed by the well-established thermodynamic properties of the binary H-Y system. Hydrogen content in as-fabricated hydride was determined by the weight change method and vacuum hot extraction technique, complemented by the X-ray diffraction (XRD). In addition, significant efforts are being dedicated to establishing a complete database of the thermomechanical properties of as-fabricated yttrium hydride. In FY2020, we investigated the thermophysical properties of yttrium hydrides as a function of temperature (room temperature to 700°C) and hydrogen concentration (H/Y ratio ranges from 1.52 to 1.93). The results indicate that at the temperatures below 300 °C, the hydrogen content did not have a significant influence on the thermal expansion, while the specific heat capacity, the thermal diffusivity, and the calculated thermal conductivity were slightly higher for the higher H/Y ratio. Between 300°C and 700 °C, a reversible second-order endothermic transition in all measured thermal properties was observed. It was also found that the onset temperatures of the observed transition varied, with the composition having inverse dependence on the hydrogen content. An attempt was made to explain the behavior of the thermophysical properties at higher temperatures by considering the order– disorder transition as a result of hydrogen redistribution. In addition, nanoindentation was employed to determine the elastic modulus and hardness and to capture the crystal orientation dependence of these parameters. Vickers hardness was also reported. The final section of the report introduces ongoing neutron irradiation campaign of yttrium hydride.
Updating the BNB Flux Prediction at SBND
Precise, accurate neutrino flux predictions for neutrino beam experiments are crucial for physics results. Flux uncertainties contribute significantly to the total systematic uncertainties seen in modern accelerator neutrino measurements such as cross sections, oscillations, and BSM studies.. For over a decade, experiments utilizing Fermilab’s Booster Neutrino Beam (BNB) have relied on the 2009 MiniBooNE flux prediction. However, the high-statistics era of the Short-Baseline Neutrino (SBN) program, with both SBND and ICARUS now operating, demands a modernized flux model and framework. While SBND is using the MiniBooNE flux model for its Generation 1 analyses, including many upcoming cross section measurements, future work will be based on a new flux model. In this talk, the ongoing work towards this new model will be outlined, including a new simulation framework (G4BNB), a new evaluation of model parameters from hadron scattering data, and a new framework for evaluating systematic uncertainties (BNBFP). Additionally, expansions to the flux model to include BSM contributions from neutral mesons will be discussed, as well as the PRISM capabilities of SBND to observe a wide range of off axis angles of the neutrino beam.