Search NASA⌕ Search

SEARCH · Search NASA

Results for “Rate formulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

Studies of premixed and non-premixed hydrogen flames

The hydrogen oxidation chemistry constitutes the foundation of the kinetics of all carbon- and hydrogen-containing fuels. The validation of rate constants of hydrogen-related reactions can be complicated by uncertainties associated with experimental data caused by the high reactivity and diffusivity of hydrogen.Here, accurate experimental data on flame propagation and extinction were determined for premixed and non-premixed hydrogen flames at pressures between p = 1 and 7 atm. The experiments were designed to sensitize the three-body H + O 2 + M → HO 2 + M reaction, whose rate is subject to notable uncertainty. This was achieved by increasing the pressure and by adding to the reactants H 2 O and CO 2 whose collision efficiencies are high compared to other species. In the present study, directly measured flame properties were compared against computed ones, in order to eliminate uncertainties associated with extrapolations, as is the case for laminar flame speeds. The measured extinction strain rates exhibit both a positive and negative dependence on pressure with and without weighting with the density, and this non-monotonic behavior is caused by the competition between the H + O 2 → O + OH and H + O 2 + M → HO 2 + M reactions as well as HO 2 kinetic pathways as pressure increases. The various kinetic models considered in this investigation did not reproduce equally well the non-premixed flame extinction data with added H 2 O. Yet, the predicted extinction strain rates were consistent between the various models in the case of added CO 2 . Finally, it was shown that the formulation of binary diffusion coefficient pairs including H–N 2 and H 2 –N 2 has a first order effect on the prediction of extinction strain rates of non-premixed H 2 flames.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Co-optimized machine-learned manifold models for large eddy simulation of turbulent combustion

Many modeling approaches in large eddy simulation (LES) of turbulent combustion employ a projection of the thermochemical state onto a low-dimensional manifold within state space to reduce the number of transported variables and hence computational cost. Flamelet-generated manifolds (FGM) is an example of a well-established, physics-based approach, but increasingly, principal component analysis (PCA) is being used as a data-driven method for generating manifold models. For both approaches, the nonlinear relationship between the location on the predefined manifold and the outputs of interest, such as reaction rates, can be tabulated or encoded in a neural network. This work proposes a new approach for manifold modeling that extends these existing approaches. A modified neural network structure simultaneously encodes the definition of the manifold variables, the nonlinear mapping, and the subfilter closure for LES. This allows all three of these aspects of the model to be co-optimized, generating a model from any source of combustion thermochemical state data. The manifold parameterizing variables are constrained to be linear combinations of species, as in FGM and PCA-based models, to aid in interpretability and implementation. For LES, subfilter variances of the manifold variables are also included as inputs. Two types of a priori analysis are performed to evaluate the new approach. In the first, the model is trained on data from one-dimensional premixed flames. In this case, the approach recovers the behavior of flamelet-based manifold approaches, and in fact slightly improves performance by identifying an optimized progress variable. The approach is also applied to data from direct numerical simulations of spherical ignition kernels in isotropic turbulence. For any specified manifold dimensionality, the new approach provides substantially lower prediction errors than a PCA-based model developed from the same data set. Additionally, the LES formulation of the new approach can provide accurate predictions for filtered reaction rates across a variety of filter widths.

97 MATHEMATICS AND COMPUTING↗

A duality-based coupling of Cosserat crystal plasticity and phase field theories for modeling grain refinement

High-rate deformation processes of metals entail intense grain refinement and special attention needs to be paid to capture the evolution of microstructure. In this article, a new formulation for coupling Cosserat crystal plasticity and phase field is developed. A common approach is to penalize kinematic incompatibility between lattice orientation and displacement-based elastic rotation. However, this can lead to significant solution sensitivity to the penalty parameter, resulting in low accuracy and convergence rates. To address these issues, a duality-based formulation is developed which directly imposes the rotational kinematic compatibility. A weak inf-sup-based skew-symmetric stress projection is introduced to suppress instabilities present in the dual formulation. An additional least squares stabilization is introduced to suppress the spurious lattice rotation with a suitable parameter range derived analytically and validated numerically. The required high-order continuity is attained by the reproducing kernel approximation. It is observed that equal order displacement-rotation-phase field approximations are stable, which allows efficient employment of the same set of shape functions for all independent variables. The proposed formulation is shown to yield superior accuracy and convergence with marginal parameter sensitivity compared to the penalty-based approach and successfully captures the dominant rotational recrystallization mechanism including block dislocation structures and grain boundary migration.

42 ENGINEERING↗

A tantalum strength model using a multiscale approach: version 2

A continuum strength model for tantalum was developed in 2007 using a multiscale approach. This was our first attempt at connecting simulation results from atomistic to continuum length scales, and much was learned that we were not able to incorporate into the model at that time. The tantalum model described in this report represents a second cut at pulling together multiscale simulation results into a continuum model. Insight gained in creating previous multiscale models for tantalum and vanadium was used to guide the model construction and functional relations for the present model. While the basic approach follows that of the vanadium model, there are significant departures. Some of the recommendations from the vanadium report were followed, but not all. Results from several new analysis techniques have not yet been incorporated due to technical difficulties. Molecular dynamics simulations of single dislocation motion at several temperatures suggested that the thermal activation barrier was temperature dependent. This dependency required additional temperature functions be included within the assumed Arrhenius relation. The combination of temperature dependent functions created a complex model with a non unique parameterization and extra model constants. The added complexity had no tangible benefits. The recommendation was to abandon the strict Arrhenius form and create a simpler curve fit to the molecular dynamics data for shear stress versus dislocation velocity. Functions relating dislocation velocity and applied shear stress were constructed vor vanadium for both edge and screw dislocations. However, an attempt to formulate a robust continuum constitutive model for vanadium using both dislocation populations was unsuccessful; the level of coupling achieved was inadequate to constrain the dislocation evolution properly. Since the behavior of BCC materials is typically assumed to be dominated by screw dislocations, the constitutive relations were ultimately built using only the screw relations. In light of this, the screw dislocation mobility relation is chosen as the starting point for the present tantalum model. Edge dislocations are not included explicitly in the current model. A significant change from the previous models is in the functional dependence of the dislocation evolution equations. The prior multiscale models assumed that the dislocation evolution rate depended on stress as well dislocation velocity. This crated an implicit dependence on the kinetic relation and required an iterative solution for the dislocation density. In the present model the integration scheme is simplified by casting the dislocation evolution terms of strain rate and current dislocation density. The final notable change was in the transition relation from the thermally activated regime to phonon drag. Historically, and in the prior models, this transition had been through a harmonic average on the strain rates making it impossible to determine the stress directly when given the plastic strain rate. After considering alternative transition relations, it was determined that an equally suitable fit to the molecular dynamics simulation data in the transition region could be constructed by averaging stresses rather than strain rates. The end result of these enhancements is a simpler (fewer parameters) and more straight forward model formulation where the material strength can be evaluated directly when given the plastic strain rate, temperature, pressure and the dislocation density at the beginning of the time step. This greatly improves the computational efficiency and robustness over the prior models where additional iteration loops were required.

36 MATERIALS SCIENCE↗

Heat Transfer Fluids as Co‐Diluents in Localized High‐Concentration Electrolytes for High‐Rate Lithium Metal Batteries With Enhanced Safety

Localized high-concentration electrolytes (LHCEs) have been identified as promising electrolyte formulations for lithium metal batteries, due to their effective interphase formation and promotion of compact Li deposition, yet their practical implementation is often limited by reduced ion transport kinetics. In this study, two industrially established fluorinated ethers are identified for the first time in battery research as effective co-diluents as they combine a broad electrochemical stability window with a low viscosity and intrinsic non-flammability. Incorporating these components, commonly used as heat transfer fluids, yields safer, less flammable electrolyte formulations with enhanced ion mobilities. In particular, the ternary co-diluent formulation shows improved ion mobility by reducing the electrolyte's viscosity while limiting excessive ion clustering. Based on the improved electrolyte transport kinetics, lower overvoltages and higher Coulombic efficiencies at current densities ≥ 1 mA cm −2 are achieved with the ternary co-diluent blend, resulting in markedly extended cycle life in an application-oriented zero-excess pouch cell compared with the baseline system. Complementary electrochemical and ex situ analysis of harvested electrodes at moderate current densities reveals no discernible differences in interphase morphology and composition, suggesting enhanced ion mobility as the primary cause of the improved high-rate performance.

electrolyte diluent↗

Plasma viscosity with mass transport in spherical inertial confinement fusion implosion simulations

The effects of viscosity and small-scale atomic-level mixing on plasmas in inertial confinement fusion(ICF) currently represent challenges in ICF research. Many current ICF hydrodynamic codes ignore the effects of viscosity though recent research indicates viscosity and mixing by classical transport processes may have a substantial impact on implosion dynamics. In this paper, we have implemented a Lagrangian hydrodynamic code in one-dimensional spherical geometry with plasmaviscosity and mass transport and including a three temperature model for ions, electrons, and radiation treated in a gray radiation diffusion approximation. The code is used to study ICF implosion differences with and without plasmaviscosity and to determine the impacts of viscosity on temperature histories and neutron yield. It was found that plasmaviscosity has substantial impacts on ICF shock dynamics characterized by shock burn timing, maximum burn temperatures, convergence ratio, and time history of neutron production rates. Finally, plasmaviscosity reduces the need for artificial viscosity to maintain numerical stability in the Lagrangian formulation and also modifies the flux-limiting needed for electron thermal conduction.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Evaluation of Autoconversion Representation in E3SMv2 Using an Ensemble of Large-Eddy Simulations of Low-Level Warm Clouds

In numerical atmospheric models that treat cloud and rain droplet populations as separate condensate categories, precipitation initiation in warm clouds is often represented by an autoconversion rate (Au), which is the rate of formation of new rain droplets through the collisions of cloud droplets. Being a function of the cloud droplet size distribution (DSD), the local Au is commonly parameterized as a function of DSD moments: cloud droplet number (n c ) and mass (q c ) concentrations. When applied in a large-scale model, the grid-mean Au must also include a correction, or enhancement factor, to account for the horizontal variability of the cloud properties across the model grid. In this study, we evaluate the Au representation in the Energy Exascale Earth System Model version 2 (E3SMv2) climate model using large-eddy simulations (LES), which explicitly resolve cloud droplet spectra, and therefore the local Au, as well as its spatial variability. The analysis of an ensemble of warm low-level cloud cases shows that the E3SMv2 formulation represents the Au reasonably well compared to the horizontally averaged explicitly computed rate from LES. The agreement, however, comes from a combination of an underestimated E3SM-tuned local Au rate and an overestimated subgrid cloud variability enhancement factor. The latter bias is traced to neglecting the horizontal variability of n c and its co-variability with q c in parameterizing the grid-mean Au.

54 ENVIRONMENTAL SCIENCES↗

A Water-Based Silver-Nanowire Screen-Print Ink for the Fabrication of Stretchable Conductors and Wearable Thin-Film Transistors

Silver nanowire is a very promising material for fabricating compliant conductors which are essential for stretchable/wearable electronic devices. Screen printing is a cost-effective and scalable technology to fabricate large-area thin film coatings with modest pattern resolution. The biggest challenge to prepare a screen printable silver nanowire ink stems from the low viscosity of silver nanowire dispersions and that the addition of a thickening agent could dramatically increase the inter-nanowire contact resistance in the resulting coating. Herein, we report the synthesis of a water-based silver nanowire ink, which was formulated with low solid contents, high viscosity at 0.1 s -1 shear rate, and appropriate rheological behavior suitable for screen printing. Silver nanowire coating patterns were screen printed with uniform sharp edges, ~50 μm resolution, and electrical conductivity as high as 4.67 × 10 4 S cm -1 . The screen printed silver nanowires were then used to fabricate a composite conductor that retained a conductivity greater than 10,000 S cm -1 under 70% tensile strain. Fully printed and stretchable/wearable thin-film transistor arrays were also fabricated by employing the screen printed composite conductor as the source, drain, and gate, drop cast semiconducting carbon nanotubes as the channel, and a dielectric elastomer. The 10 × 6 thin-film transistor arrays had a fabrication yield of 91.7%, average mobility of 33.8 ± 3.7 cm 2 V -1 s -1 , ON/OFF ratio ~1000, and remained stable during 1,000 cycles of wearing on and peeling off a glass tube with 5 mm diameter.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Incorporating PCM-enabled thermal energy storage into 3D printable cementitious composites

This paper delineates the feasibility of incorporating microencapsulated phase change materials (mPCM) into 3D printable cementitious composite materials. A comprehensive experimental program was carried out to evaluate the impacts of mPCM on the printability, microstructures, mechanical and thermal properties of cementitious 3D printing ‘inks’. Results showed that the mPCM affected the printability of the cementitious ink material based on its physical properties (e.g., particle size) and volume loading – at lower volume loadings, mPCM increased the flowability of the cementitious ink material while leading to increased compressive strength and thermal conductivity for the hardened printed material. However, further increase in mPCM dosage led to a decrease in printability and, therefore, decrease in compressive strength and thermal conductivity as compared to the reference mixture. Here the results also showed that the inclusion of mPCM influence the printing parameters. In general, the inclusion of higher volume contents of mPCM necessitates a higher extrusion rate to achieve a desirable extrudability. Lastly, a thermal network model was formulated for 3D printed mPCM charged building components (e.g., wall). The study shows that microencapsulated PCM materials have good potential to be used in 3D printable cementitious mixtures for improving the thermal and energy performance of 3D printed buildings.

36 MATERIALS SCIENCE↗

Desensitizing ignition of energetic materials when exposed to accidental fire

Composite energetic materials combine fuel and oxidizers for high energy density exothermic reactions and are used for ordnance, industrial and localized power generation applications. This study focuses on examining an additive to a mixture of aluminum (Al) and copper oxide (CuO) to decrease ignition sensitivity under accidental fire exposure conditions. Ammonium nitrate (AN) was incorporated into Al+CuO, as a 1:1 replacement for CuO, for varied equivalence ratios and examined for ignition and combustion when exposed to slow and fast heating rate ignition conditions. The goal was to develop an Al+CuO+AN formulation that would perform comparable to Al+CuO when intentionally ignited, but would not ignite in an accidental fire. Experimental results show that Al+CuO+AN with an equivalence ratio (ER) ranging from 4.0–5.5 inerts the reactants when exposed to slow heating conditions, yet ignites with comparative combustion performance to the baseline Al+CuO mixture when exposed to fast heating conditions. These results are consistent with thermochemical simulations of the heat of combustion and adiabatic flame temperature for the respective reactions. In conclusion, this study presents a new approach for tailoring composite energetic materials toward accidental fire safety by exploiting the early stage decomposition kinetics of AN, which are activated only by slow heating ignition conditions.

36 MATERIALS SCIENCE↗

Temperature and Composition Dependence Modeling of Viscosity and Electrical Conductivity of Low-Activity Waste Glass Melts

The development of models that accurately relate the properties of a glass melt to its temperature and composition is important for glass formulation, melter control, and modeling the melt flow, refractory corrosion, and production rate. Using a database consisting of more than 4,000 data points measured between 900 °C and 1250 °C for over 600 unique low-activity waste glass compositions, we developed models for the melt viscosity and electrical conductivity. Models based on the Gaussian process regression approach outperformed models based on the Vogel–Fulcher–Tammann equation according to four standard metrics and yielded reliable prediction intervals. The models found primarily linear effects between properties and individual components, except for the effect of the Na 2 O mass fraction on the electrical conductivity. The effects were found to be consistent with current theories on physical processes involved with those properties.

36 MATERIALS SCIENCE↗

Uncertainty Quantification in CO 2 Sequestration Using Surrogate Models from Polynomial Chaos Expansion

In this paper, surrogate models are iteratively built using polynomial chaos expansion (PCE) and detailed numerical simulations of a carbon sequestration system. Output variables from a numerical simulator are approximated as polynomial functions of uncertain parameters. Once generated, PCE representations can be used in place of the numerical simulator and often decrease simulation times by several orders of magnitude. However, PCE models are expensive to derive unless the number of terms in the expansion is moderate, which requires a relatively small number of uncertain variables and a low degree of expansion. To cope with this limitation, instead of using a classical full expansion at each step of an iterative PCE construction method, we introduce a mixed-integer programming (MIP) formulation to identify the best subset of basis terms in the expansion. This approach makes it possible to keep the number of terms small in the expansion. Monte Carlo (MC) simulation is then performed by substituting the values of the uncertain parameters into the closed-form polynomial functions. Based on the results of MC simulation, the uncertainties of injecting CO{sub 2} underground are quantified for a saline aquifer. Moreover, based on the PCE model, we formulate an optimization problem to determine the optimal CO{sub 2} injection rate so as to maximize the gas saturation (residual trapping) during injection, and thereby minimize the chance of leakage.

54 ENVIRONMENTAL SCIENCES↗

Energy transfer in reconnection and turbulence

Reconnection and turbulence are two of the most commonly observed dynamical processes in plasmas, but their relationship is still not fully understood. Using 2.5D kinetic particle-in-cell simulations of both strong turbulence and reconnection, we compare the cross-scale transfer of energy in the two systems by analyzing the generalization of the von Kármán Howarth equations for Hall magnetohydrodynamics, a formulation that subsumes the third-order law for steady energy transfer rates. Even though the large scale features are quite different, the finding is that the decomposition of the energy transfer is structurally very similar in the two cases. In the reconnection case, the time evolution of the energy transfer also exhibits a correlation with the reconnection rate. Finally, these results provide explicit evidence that reconnection dynamics fundamentally involves turbulence-like energy transfer.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Vitrification Testing of HLW with High Phosphate

Projections of the number of high level waste (HLW) canisters to be produced in the Hanford Tank Waste Treatment and Immobilization Plant (WTP) (e.g., [1]) are based upon the inventory of the tank wastes, the anticipated performance of the sludge treatment processes, and current understanding of the capability of the borosilicate glass waste form. The WTP HLW melter design, unlike earlier Department of Energy (DOE) melter designs, incorporates a glass bubbler system. The bubblers create active glass pool mixing and thereby improve heat and mass transfer and glass melting rate. The WTP HLW melters each have a glass surface area of 3.75 m 2 and depth of ~1.1 m. The two melters in the HLW facility together are designed to produce up to 7.5 MT of glass per day at 100% availability. Further increases in HLW waste processing rates can potentially be achieved by optimization of the feed and glass formulations, increasing the melter operating temperature above 1150⁰C, and by increasing the waste loading in the glass product. Increasing the waste loading also has the added benefit of decreasing the number of canisters for storage.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Sensitivity and Discovery Potential of CUORE to Neutrinoless Double-Beta Decay

We present a study of the sensitivity and discovery potential of CUORE, a bolometric double-beta decay experiment under construction at the Laboratori Nazionali del Gran Sasso in Italy. Two approaches to the computation of experimental sensitivity for various background scenarios are presented, and an extension of the sensitivity formulation to the discovery potential case is also discussed. Assuming a background rate of 10 -2 cts/(keV kg y), we find that, after 5 years of live time, CUORE has a 1 sigma sensitivity to the neutrinoless double-beta decay half-life of T$0v\atop{1/2}$(1θ) = 1.6 \times 10 26 y and thus a potential to probe the effective Majorana neutrino mass down to 40-100 meV; the sensitivity at 1.64 sigma, which corresponds to 90% C.L., will be T$0v\atop{1/2}$(1.64θ) = 9.5 \times 10 25 y. This range is compared with the claim of observation of neutrinoless double-beta decay in 76 Ge and the preferred range of the neutrino mass parameter space from oscillation results.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Temperature, humidity and air flow in the emplacement drifts using convection and dispersion transport models

A coupled thermal-hydrologic-airflow model is developed, solving for the transport processes within a waste emplacement drift and the surrounding rockmass together at the proposed nuclear waste repository at Yucca Mountain. Natural, convective air flow as well as heat and mass transport in a representative emplacement drift during post-closure are explicitly simulated, using the MULTIFLUX model. The conjugate, thermal-hydrologic transport processes in the rockmass are solved with the TOUGH2 porous-media simulator in a coupled way to the in-drift processes. The new simulation results show that large-eddy turbulent flow, as opposed to small-eddy flow, dominate the drift air space for at least 5000 years following waste emplacement. The size of the largest, longitudinal eddy is equal to half of the drift length, providing a strong axial heat and moisture transport mechanism from the hot to the cold drift sections. The in-drift results are compared to those from simplified models using a surrogate, dispersive model with an equivalent dispersion coefficient for heat and moisture transport. Results from the explicit, convective velocity simulation model provide higher axial heat and moisture fluxes than those estimated from the previously published, simpler, equivalent-dispersion models, in addition to showing differences in temperature, humidity and condensation rate distributions along the drift length. A new dispersive model is also formulated, giving a time- and location-variable function that runs generally about ten times higher in value than the highest dispersion coefficient currently used in the Yucca Mountain Project as an estimate for the equivalent dispersion coefficient in the emplacement drift. The new dispersion coefficient variation, back-calculated from the convective model, can adequately describe the heat and mass transport processes in the emplacement drift example.

54 ENVIRONMENTAL SCIENCES↗

A pseudo-kinetic model to simulate phase changes in gas hydrate bearing sediments

Herein, modeling of the phase transitions anticipated in gas hydrate bearing sediments (GHBS) is critical for a proper understanding of time-dependent changes in states and volumes (e.g. the production of methane from this type of soils). We propose a new pseudo-kinetic approach to simulate the typical phase changes anticipated in GHBS, using published experimental results involving gas hydrate dissociation that are the basis of a widely used kinetic model. The proposed pseudo-kinetic model is formulated in the pressure-temperature (P-T) plane and assumes a rate of gas hydrate dissociation (or formation) proportional to the distance between the current state and the phase boundary. The model consists of only one parameter and is simple to implement in numerical simulators. A similar concept is used to model ice formation/thawing phenomena, but based on the ice/liquid-water phase boundary. We implemented the pseudo-kinetic model in a fully coupled thermo-hydro-chemo-mechanical (THCM) finite element code and validated it against experimental results performed on the dissociation of synthetic gas hydrate. We also evaluated the pseudo-kinetic model using synthetic cases covering several scenarios associated with gas hydrate formation/dissociation and ice formation/thawing. The model successfully reproduced the gas production test from a natural GHBS core from Korea (scaled gas venting experiment over 14 h), and also the formation of gas hydrate and ice in permafrost in Alaska (over 2 × 10 6 years). -The analyses show the versatility of the proposed pseudo-kinetic approach by applying it to model the different types of phase transitions typically encounter in GHBS. The simple formulation, easy implementation in numerical simulator, and reduced number of parameters (only one per phase change) make this model an attractive option for simulating phase transformations in problems involving GHBS.

58 GEOSCIENCES↗