Search NASA⌕ Search

SEARCH · Search NASA

Results for “Rotary Wing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS2013

Study and Sub-System Optimization of Propulsion and Drive Systems for the Large Civil TiltRotor (LCTR2) Rotorcraft

In a series of study tasks conducted as a part of NASA's Fundamental Aeronautics Program, Rotary Wing Project, Boeing and Rolls-Royce explored propulsion, drive, and rotor system options for the NASA Large Civil Tilt Rotor (LCTR2) concept vehicle. The original objective of this study was to identify engine and drive system configurations to reduce rotor tip speed during cruise conditions and quantify the associated benefits. Previous NASA studies concluded that reducing rotor speed (from 650 fps hover tip speed) during cruise would reduce vehicle gross weight and fuel burn. Initially, rotor cruise speed ratios of 54% of the hover tip speed were of most interest during operation at cruise air speed of 310 ktas. Interim results were previously reported1 for cruise tip speed ratios of 100%, 77%, and 54% of the hover tip speed using engine and/or gearbox features to achieve the reduction. Technology levels from commercial off-the-shelf (COTS), through entry-in-service (EIS) dates of 2025 and 2035 were considered to assess the benefits of advanced technology on vehicle gross weight and fuel burn. This technical paper presents the final study results in terms of vehicle sizing and fuel burn as well as Operational and Support (O&S) costs. New vehicle sizing at rotor tip speed reduced to 65% of hover is presented for engine performance with an EIS 2035 fixed geometry variable speed power turbine. LCTR2 is also evaluated for missions range cases of 400, 600, 800, 1000, and 1200 nautical miles and cruise air speeds of 310, 350 and 375 ktas.

Robuck, Mark↗
NASA NTRS2014

Design Optimization of a Variable-Speed Power Turbine

NASA's Rotary Wing Project is investigating technologies that will enable the development of revolutionary civil tilt rotor aircraft. Previous studies have shown that for large tilt rotor aircraft to be viable, the rotor speeds need to be slowed significantly during the cruise portion of the flight. This requirement to slow the rotors during cruise presents an interesting challenge to the propulsion system designer as efficient engine performance must be achieved at two drastically different operating conditions. One potential solution to this challenge is to use a transmission with multiple gear ratios and shift to the appropriate ratio during flight. This solution will require a large transmission that is likely to be maintenance intensive and will require a complex shifting procedure to maintain power to the rotors at all times. An alternative solution is to use a fixed gear ratio transmission and require the power turbine to operate efficiently over the entire speed range. This concept is referred to as a variable-speed power-turbine (VSPT) and is the focus of the current study. This paper explores the design of a variable speed power turbine for civil tilt rotor applications using design optimization techniques applied to NASA's new meanline tool, the Object-Oriented Turbomachinery Analysis Code (OTAC).

design optimization↗
NASA NTRS2014

Test Facility Simulation Results for Aerospace Loss-of-Lubrication of Spur Gears

Prior to receiving airworthiness certification, extensive testing is required during the development of rotary wing aircraft drive systems. Many of these tests are conducted to demonstrate the drive system's ability to operate at extreme conditions, beyond that called for in the normal to maximum power operating range. One of the most extreme tests is referred to as the loss-of-lubrication or run dry test. During this test, the drive system is expected to last at least 30 min without failure while the primary lubrication system is disabled for predetermined, scripted flight conditions. Failure of this test can lead to a partial redesign of the drive system or the addition of an emergency lubrication system. Either of these solutions can greatly increase the aircraft drive system cost and weight and extend the schedule for obtaining airworthiness certification. Recent work at NASA Glenn Research Center focused on performing tests, in a relevant aerospace environment, to simulate the behavior of spur gears under loss-of-lubrication conditions. Tests were conducted using a test facility that was used in the past for spur gear contact fatigue testing. A loss-oflubrication test is initiated by shutting off the single into mesh lubricating jet. The test proceeds until the gears fail and can no longer deliver the applied torque. The observed failures are typically plastically deformed gear teeth, due to the high tooth temperatures, that are no longer in mesh. The effect of several different variables to gear tooth condition during loss-of-lubrication have been tested such as gear pitch, materials, shrouding, lubrication condition, and emergency supplied mist lubrication in earlier testing at NASA. Recent testing has focused on newer aerospace gear steels and imbedding thermocouples in the shrouding to measure the air-oil temperatures flung off the gear teeth. Along with the instrumented shrouding, an instrumented spur gear was also tested. The instrumented spur gear had five thermocouples installed at different locations on the gear tooth and web. The data from these two types of measurements provided important information as to the thermal environment during the loss-of-lubrication event. This data is necessary to validate on-going modeling efforts.

Gears↗
NASA NTRS2014

Evaluation of the First Transport Rotorcraft Airframe Crash Testbed (TRACT 1) Full-Scale Crash Test

In 2012, the NASA Rotary Wing Crashworthiness Program initiated the Transport Rotorcraft Airframe Crash Testbed (TRACT) research program by obtaining two CH-46E helicopters from the Navy CH-46E Program Office (PMA-226) at the Navy Flight Readiness Center in Cherry Point, North Carolina. Full-scale crash tests were planned to assess dynamic responses of transport-category rotorcraft under combined horizontal and vertical impact loading. The first crash test (TRACT 1) was performed at NASA Langley Research Center's Landing and Impact Research Facility (LandIR), which enables the study of critical interactions between the airframe, seat, and occupant during a controlled crash environment. The CH-46E fuselage is categorized as a medium-lift rotorcraft with fuselage dimensions comparable to a regional jet or business jet. The first TRACT test (TRACT 1) was conducted in August 2013. The primary objectives for TRACT 1 were to: (1) assess improvements to occupant loads and displacement with the use of crashworthy features such as pre-tensioning active restraints and energy absorbing seats, (2) develop novel techniques for photogrammetric data acquisition to measure occupant and airframe kinematics, and (3) provide baseline data for future comparison with a retrofitted airframe configuration. Crash test conditions for TRACT 1 were 33-ft/s forward and 25-ft/s vertical combined velocity onto soft soil, which represent a severe, but potentially survivable impact scenario. The extraordinary value of the TRACT 1 test was reflected by the breadth of meaningful experiments. A total of 8 unique experiments were conducted to evaluate ATD responses, seat and restraint performance, cargo restraint effectiveness, patient litter behavior, and photogrammetric techniques. A combination of Hybrid II, Hybrid III, and ES-2 Anthropomorphic Test Devices (ATDs) were placed in forward and side facing seats and occupant results were compared against injury criteria. Loads from ATDs in energy absorbing seats and restraints were within injury limits. Severe injury was likely for ATDs in forward facing passenger seats, legacy troop bench seats, and a three-tiered patient litter. In addition, two standing ATDs were used to evaluate the benefit of Mobile Aircrew Restraint Systems (MARS) versus a standard gunner's belt. The ATD with the MARS survived the impact, while fatal head blunt trauma occurred for the standing ATD held by the legacy gunner's belt. In addition to occupant loading, the structural response of the airframe was assessed based on accelerometers located throughout the airframe and using three-dimensional photogrammetric techniques. Analysis of the photogrammetric data indicated regions of maximum deflection and permanent deformation.

Annett, Martin S.↗
NASA NTRS2014

Fully Integral, Flexible Composite Driveshaft

An all-composite driveshaft incorporating integral flexible diaphragms was developed for prime contractor testing. This new approach makes obsolete the split lines required to attach metallic flex elements and either metallic or composite spacing tubes in current solutions. Subcritical driveshaft weights can be achieved that are half that of incumbent technology for typical rotary wing shaft lengths. Spacing tubes compose an integral part of the initial tooling but remain part of the finished shaft and control natural frequencies and torsional stability. A concurrently engineered manufacturing process and design for performance competes with incumbent solutions at significantly lower weight and with the probability of improved damage tolerance and fatigue life.

Lawrie, Duncan↗
NASA NTRS2015

Robust, Flexible and Lightweight Dielectric Barrier Discharge Actuators Using Nanofoams/Aerogels

Robust, flexible, lightweight, low profile enhanced performance dielectric barrier discharge actuators (plasma actuators) based on aerogels/nanofoams with controlled pore size and size distribution as well as pore shape. The plasma actuators offer high body force as well as high force to weight ratios (thrust density). The flexibility and mechanical robustness of the actuators allows them to be shaped to conform to the surface to which they are applied. Carbon nanotube (CNT) based electrodes serve to further decrease the weight and profile of the actuators while maintaining flexibility while insulating nano-inclusions in the matrix enable tailoring of the mechanical properties. Such actuators are required for flow control in aeronautics and moving machinery such as wind turbines, noise abatement in landing gear and rotary wing aircraft and other applications.

Sauti, Godfrey↗
NASA NTRS2015

Active Aerodynamic Load Reduction on a Rotorcraft Fuselage With Rotor Effects: A CFD Validation Effort

A rotorcraft fuselage is typically designed with an emphasis on operational functionality with aerodynamic efficiency being of secondary importance. This results in a significant amount of drag during high-speed forward flight that can be a limiting factor for future high-speed rotorcraft designs. To enable higher speed flight, while maintaining a functional fuselage design (i.e., a large rear cargo ramp door), the NASA Rotary Wing Project has conducted both experimental and computational investigations to assess active flow control as an enabling technology for fuselage drag reduction. This paper will evaluate numerical simulations of a flow control system on a generic rotorcraft fuselage with a rotor in forward flight using OVERFLOW, a structured mesh Reynolds-averaged Navier-Stokes flow solver developed at NASA. The results are compared to fuselage forces, surface pressures, and PN flow field data obtained in a wind tunnel experiment conducted at the NASA Langley 14-by 22-Foot Subsonic Tunnel where significant drag and download reductions were demonstrated using flow control. This comparison showed that the Reynolds-averaged Navier-Stokes flow solver was unable to predict the fuselage forces and pressure measurements on the ramp for the baseline and flow control cases. While the CFD was able to capture the flow features, it was unable to accurately predict the performance of the flow control.

Allan, Brian G.↗
NASA NTRS2015

Case Studies for the Statistical Design of Experiments Applied to Powered Rotor Wind Tunnel Tests

The application of statistical Design of Experiments (DOE) to helicopter wind tunnel testing was explored during two powered rotor wind tunnel entries during the summers of 2012 and 2013. These tests were performed jointly by the U.S. Army Aviation Development Directorate Joint Research Program Office and NASA Rotary Wing Project Office, currently the Revolutionary Vertical Lift Project, at NASA Langley Research Center located in Hampton, Virginia. Both entries were conducted in the 14- by 22-Foot Subsonic Tunnel with a small portion of the overall tests devoted to developing case studies of the DOE approach as it applies to powered rotor testing. A 16-47 times reduction in the number of data points required was estimated by comparing the DOE approach to conventional testing methods. The average error for the DOE surface response model for the OH-58F test was 0.95 percent and 4.06 percent for drag and download, respectively. The DOE surface response model of the Active Flow Control test captured the drag within 4.1 percent of measured data. The operational differences between the two testing approaches are identified, but did not prevent the safe operation of the powered rotor model throughout the DOE test matrices.

Overmeyer, Austin D.↗
NASA NTRS2018

Mid-Fidelity Computational Fluid Dynamics Analysis of the Elytron 4S UAV Concept

The Elytron 4S Unmanned Aerial Vehicle (UAV) Concept was developed to combine the advantages of fixed- and rotary-wing technology. The 4S Concept is a box-wing configuration with rotors mounted on a centrally located tiltwing. The UAV is intended to be capable of both conventional takeoff and landing (CTOL) and vertical takeoff and landing (VTOL), and is envisioned to excel in UAV performance because of the combined efficiency of fixed-wing aircraft and the hover and VTOL capabilities of regular drones or quadcopters. A mid-fidelity Unsteady Reynolds-Averaged Navier-Stokes (URANS) approach using Rotorcraft CFD (RotCFD) is performed to analyze and characterize the performance of the aircraft. The flow field is coupled with a rotor model based on blade-element momentum theory to model the 4S UAV rotors. Turbulence is modeled using a realizable k- turbulence model with special wall function. The code is used to generate aerodynamic forces and moments on the body at cruise conditions, and during VTOL. The results and their uncertainties are characterized, and an angle- of-attack and sideslip sweep are computed, both with and without rotors on. Simulations are compared with the wind tunnel tests in the 7- by 10-Foot U.S. Army Wind Tunnel at NASA Ames Research Center, performed in 2017. Results show promising comparison with experimental data, despite a late change in rotor size and rudder size of the physical model that cause the expected deviations from the simulation. A slight change in the net thrust value, when rotors are modeled, is observed because of the rotor diameter increase on the physical model. A noticeable difference in the directional stability was observed because of the increased rudder surface and added strakes. These changes were implemented to improve on the design as simulated, which is observed in the results. The simulation results paved the way to the first successful flight of the UAV Concept.

Koning, Witold J. K.↗
NASA NTRS2017

Modelling the Risks Remotely Piloted Aircraft Pose to People on the Ground

Worldwide there is much e ort being directed towards the development of a framework of air- worthiness regulations for remotely piloted aircraft systems (RPAS). It is now broadly accepted that regulations should have a strong foundation in, and traceability to, the management of the safety risks. Existing risk models for RPAS operations do not provide a simple means for incorporating the wide range of technical and operational controls into the risk analysis and evaluation processes. This paper describes a new approach for modelling and evaluating the risks associated with RPAS operations near populous areas based on the barrier bow tie (BBT) model. A BBT model is used to structure the underlying risk management problem. The model focuses risk analysis, evaluation, and decision making activities on the devices, people, and processes that can be employed to reduce risk. The BBT model and a comprehensive set of example risk controls are presented. The general model can be applied to any RPAS operation. The foundations for quantitative and qualitative assessments using a BBT model are also presented. The modelling and evaluation framework is illustrated through its application to a case-study rotary wing RPAS for two operational scenarios. The model can be used as a basis for determining airworthiness certification requirements for RPAS.

Barrier bow tie model↗
NASA NTRSDate not supplied

TPSAS-NF1676L-12829-DND

Collaborative research between NASA and U.S. rotorcraft companies through the Vertical Lift Consortium, to design, test, and analyze representative validation test articles. - Representative problems and designs developed with partners - Validation articles and characterization specimens manufactured by partners - Develop analytical models to predict delamination behavior using commercial codes, characterization data, and test article data - NASA Space Act Agreement (SAA1-818) with CRI, August 2007 August 2012; funded through Subsonic Rotary Wing program

Gretchen B Murri↗
NASA NTRSDate not supplied

TPSAS-NF1676L-14362-DND

Overview of Subsonic Rotary Wing project for plenary session of Fundamental Aeronautics Annual meeting.

Susan A Gorton↗
NASA NTRSDate not supplied

Enhancing Fault Isolation for Health Monitoring of Electric Aircraft Propulsion by Embedding Failure Mode and Effect Analysis into Bayesian Networks

This paper describes a fault isolation approach for electric powertrains of unmanned aerial vehicles. The approach leverages the combination of failure mode and effect analysis (FMEA) and Bayesian networks, thus introducing depend-ability structures into a diagnostic framework. Faults and failure events from the FMEA are mapped within a Bayesian network, where network edges replicate the links embedded within FMEAs. This framework helps the fault isolation process by identifying the probability of occurrence of specific faults or root causes given evidence observed through sensor signals. The framework is applied to an electric power-train system of a small, rotary-wing unmanned aerial vehicle, demonstrating how a Bayesian network enhanced by FMEA helps disambiguate between root causes of incipient failures, which would otherwise be considered as equally probable.

Fault Isolation↗
NASA NTRSDate not supplied

Prediction-Based Auralization of a Multirotor Urban Air Mobility Vehicle

Recent advances in auralization methods applicable to rotary wing vehicles have made it possible to undertake a prediction-based auralization of a representative multirotor urban air mobility vehicle. These advances include a new capability for synthesizing loading and thickness noise directly from the prediction method and a new capability for predicting and synthesizing modulating broadband self noise within a unified system noise prediction-auralization framework. These capabilities are demonstrated for a six passenger quadrotor reference vehicle design using collective-pitch control. Propagation of the source noise to a ground observer completes the auralization process. The demonstrated capability serves as the basis for future work directed at perception-influenced design of low noise urban air mobility vehicles.

Auralization↗
NASA NTRSDate not supplied

ACAS Xr Part Task Sim, Preliminary Experiment Design

In early 2022, the Human Autonomy Teaming Lab (NASA Ames Research Center) will conduct a manned, human-in-the-loop (HITL) simulation. This part task HITL will begin the lab’s Hazard Perception and Avoidance (HPA) technical work under NASA’s Advanced Air Mobility (AAM), Automated Flight and Contingency Management (AFCM) Sub-Project. The goals will be to assess levels of automation for manned, electric vertical takeoff and landing (eVTOL) aircraft. This simulation will test manual and automated Resolution Advisory (RA) responses and return-to-course (RTC) maneuvers for the first version of the Airborne Collision Avoidance System’s (ACAS) rotary-wing (Xr) variant. This will be conducted on a fixed-based simulator designed to fly eVTOL aircraft while maneuvering for intruding traffic. Variables for this study include levels of autonomy (i.e., manual and automated) as well as the types of alerts at the onset of conflicts (i.e., Corrective and RA). The data collected will include response times, losses of well clear, and maneuver sizes and durations as well as subjective ratings like acceptability, perceived workload, and meaningful human control. Additional details and future anticipations are also discussed.

air taxis↗
NASA NTRSDate not supplied

Generalized Predictive Control for Active Stability Augmentation and Vibration Reduction on an Aeroelastic Tiltrotor Model

Tiltrotor aircraft are defining the state-of-the-art in vertical lift technology as they have the potential to greatly expand rotary-wing operational boundaries. However, they are often limited in forward flight speed due to complex coupled rotor and wing dynamic instabilities. The U.S. Army and NASA have been developing a new wind tunnel model, the TiltRotor Aeroelastic Stability Testbed(TRAST), to test proprotors in the NASA Langley Research Center Transonic Dynamics Tunnel (TDT) to investigate aeroelastic stability in cruise. The test is intended to provide high-quality research data for analytical tool development and validation. In addition, the TRAST model will support, develop, and mature new technologies for the design of advanced proprotor aircraft. Stability augmentation and vibration reduction during testing is planned with the use of an active control methodology known as Generalized Predictive Control(GPC). GPC is an autoregressive control law that experimentally acquires a system identification to derive the input-output relation of controls and corresponding sensors. This type of control law is especially useful for complex dynamic interactions that are difficult to explicitly model such as proprotor pylon instability, often referred to as whirl flutter. GPC has been successfully employed on other tiltrotor vehicles to suppress whirl flutter instabilities and vibrations. To aid in the characterization of the wind-tunnel model and in tool development, an analytical representation of the wind-tunnel model was developed using the rotorcraft comprehensive analysis system (RCAS) that simulates structural dynamics and aerodynamics. RCAS was used to derive state-space estimates of the physical plant at various flight conditions to test control law effectiveness. This paper will present an overview of the test article development, a description of RCAS, an explanation of the GPC methodology, and results of GPC being applied to state-space plant estimates of the TRAST model. In these simulations, GPC was effective at stabilizing the aircraft beyond the whirl-flutter boundary while simultaneously reducing vibrations across the flight regime. Additionally, a modern advancement to GPC, termed advanced GPC (AGPC), is introduced that enables a self-adapting system identification. Preliminary results show that AGPC is successful at self-correction as the plant changes from what was used for system identification.

tiltrotor↗
NASA NTRSDate not supplied

Overlap Preservation Using Loosely-Coupled Boundary Conditions for Body-Fitted Structured Overset Grids

Several improvements are made to overlap preservation in the automated approach to generating overset structured meshes. A loosely-coupled boundary condition (LCBC) is introduced to maintain optimal overlap for surface meshes generated from overlapping initial curves. Extension of the LCBC scheme to three-dimensional volume meshing is also presented. Test cases include various rotary wing vehicles from NASA’s Revolutionary Vertical Lift Technology (RVLT) project, and the wing-body geometry from the NASA Juncture Flow Experiment. Results demonstrate improvements in donor stencil quality from the enhanced overlap between neighboring surface and volume meshes.

TTT↗