Search NASA⌕ Search

SEARCH · Search NASA

Results for “Rotor noise”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

An analytical parametric study of the broadband noise from axial-flow fans

The rotating dipole analysis of Ffowcs Williams and Hawkings (1969) is used to predict the far field noise radiation due to various rotor broadband noise mechanisms. Consideration is given to inflow turbulence noise, attached boundary layer/trailing-edge interaction noise, tip-vortex formation noise, and trailing-edge thickness noise. The parametric dependence of broadband noise from unducted axial-flow fans on several critical variables is studied theoretically. The angle of attack of the rotor blades, which is related to the rotor performance, is shown to be important to the trailing-edge noise and to the tip-vortex formation noise.

Chou, Shau-Tak↗

High speed helicopter noise sources

The state-of-the art of helicopter rotor impulsive noise is reviewed. A triangulation technique for locating impulsive noise sources is developed using once-per-rev index signals as time references. A computer program (INSL) was written implementing this technique. Applying triangulation to the full-scale UH-1 noise data of NASA/Ames Research Center 40- by 80-Foot Wind Tunnel, three different noise sources are found on the rotor disk. The primary sources of thickness noise are in the second quadrant and on the advancing side of rotor disk. Two aerodynamic sources due to blade/vortex interaction are found in the first quadrant.

Lee, A.↗

Fan noise reduction achieved by removing tip flow irregularities behind the rotor - forward arc test configurations

The noise source caused by the interaction of the rotor tip flow irregularities (vortices and velocity defects) with the downstream stator vanes was studied. Fan flow was removed behind a 0.508 meter (20 in.) diameter model turbofan through an outer wall slot between the rotor and stator. Noise measurements were made with far-field microphones positioned in an arc about the fan inlet and with a pressure transducer in the duct behind the stator. Little tone noise reduction was observed in the forward arc during flow removal; possibly because the rotor-stator interaction noise did not propagate upstream through the rotor. Noise reductions were maded in the duct behind the stator and the largest decrease occurred with the first increment of flow removal. This result indicates that the rotor tip flow irregularity-stator interaction is as important a noise producing mechanism as the normally considered rotor wake-stator interaction.

Dittmar, J. H.↗

The cost of noise reduction in commercial tilt rotor aircraft

The relationship between direct operating cost (DOC) and departure noise annoyance was developed for commercial tilt rotor aircraft. This was accomplished by generating a series of tilt rotor aircraft designs to meet various noise goals at minimum DOC. These vehicles were spaced across the spectrum of possible noise levels from completely unconstrained to the quietest vehicle that could be designed within the study ground rules. A group of optimization parameters were varied to find the minimum DOC while other inputs were held constant and some external constraints were met. This basic variation was then extended to different aircraft sizes and technology time frames. It was concluded that reducing noise annoyance by designing for lower rotor tip speeds is a very promising avenue for future research and development. It appears that the cost of halving the annoyance compared to an unconstrained design is insignificant and the cost of halving the annoyance again is small.

Faulkner, H. B.↗

Noise of a model helicopter rotor due to ingestion of turbulence

A theoretical and experimental investigation of the noise of a model helicoper rotor due to ingestion of turbulence was conducted. Experiments were performed with a 0.76 m dia, articulated model rotor for a range of inflow turbulence and rotor operating conditions. Inflow turbulence levels varied from approximately 2 to 19 percent and tip Mach number was varied from 0.3 to 0.52. Test conditions included ingestion of a atmospheric turbulence in outdoor hover as well as ingestion of grid generated isotropic turbulence in the wind tunnel airstream. In wind tunnel testing, both forward flight and vertical ascent (climb) were simulated. Far field noise spectra and directivity were measured in addition to incident turbulence intensities, length scales, and spectra. Results indicate that ingestion of atmospheric turbulence is the dominant helicopter rotor hover noise mechanism at the moderate to high frequencies which determine perceived noise level.

Paterson, R. W.↗

Prediction of the Aero-Acoustic Performance of Open Rotors

The rising cost of jet fuel has renewed interest in contrarotating open rotor propulsion systems. Contemporary design methods offer the potential to maintain the inherently high aerodynamic efficiency of open rotors while greatly reducing their noise output, something that was not feasible in the 1980's designs. The primary source mechanisms of open rotor noise generation are thought to be the front rotor wake and tip vortex interacting with the aft rotor. In this paper, advanced measurement techniques and high-fidelity prediction tools are used to gain insight into the relative importance of the contributions to the open rotor noise signature of the front rotor wake and rotor tip vortex. The measurements include three-dimensional particle image velocimetry of the intra-rotor flowfield and the acoustic field of a model-scale open rotor. The predictions provide the unsteady flowfield and the associated acoustic field. The results suggest that while the front rotor tip vortex can have a significant influence on the blade passing tone noise produced by the aft rotor, the front rotor wake plays the decisive role in the generation of the interaction noise produced as a result of the unsteady aerodynamic interaction of the two rotors. At operating conditions typical of takeoff and landing operations, the interaction noise level is easily on par with that generated by the individual rotors, and in some cases is even higher. This suggests that a comprehensive approach to reducing open rotor noise should include techniques for mitigating the wake of the front rotor as well as eliminating the interaction of the front rotor tip vortex with the aft rotor blade tip.

VanZante, Dale↗

Prediction of the Aero-Acoustic Performance of Open Rotors

The rising cost of jet fuel has renewed interest in contrarotating open rotor propulsion systems. Contemporary design methods offer the potential to maintain the inherently high aerodynamic efficiency of open rotors while greatly reducing their noise output, something that was not feasible in the 1980's designs. The primary source mechanisms of open rotor noise generation are thought to be the front rotor wake and tip vortex interacting with the aft rotor. In this paper, advanced measurement techniques and high-fidelity prediction tools are used to gain insight into the relative importance of the contributions to the open rotor noise signature of the front rotor wake and rotor tip vortex. The measurements include three-dimensional particle image velocimetry of the intra-rotor flowfield and the acoustic field of a model-scale open rotor. The predictions provide the unsteady flowfield and the associated acoustic field. The results suggest that while the front rotor tip vortex can have a significant influence on the blade passing tone noise produced by the aft rotor, the front rotor wake plays the decisive role in the generation of the interaction noise produced as a result of the unsteady aerodynamic interaction of the two rotors. At operating conditions typical of takeoff and landing operations, the interaction noise level is easily on par with that generated by the individual rotors, and in some cases is even higher. This suggests that a comprehensive approach to reducing open rotor noise should include techniques for mitigating the wake of the front rotor as well as eliminating the interaction of the front rotor tip vortex with the aft rotor blade tip.

Van Zante, Dale E.↗

NASA/GE Collaboration on Open Rotors - High Speed Testing

A low-noise open rotor system is being tested in collaboration with General Electric and CFM International, a 50/50 joint company between Snecmaand GE. Candidate technologies for lower noise will be investigated as well as installation effects such as pylon integration. Current test status for the 8x6 SWT high speed testing is presented as well as future scheduled testing which includes the FAA/CLEEN test entry. The tunnel blockage and propeller thrust calibration configurations are shown.

VanZante, Dale E.↗

Study of noise on a small-scale hovering tilt rotor

A study of the noise from a small-scale, semi-span test of a hovering tilt rotor is presented. The effect on noise of the tilt rotor fountain and of several tilt rotor configuration changes is examined. Measurments were made of an isolated rotor; rotor and wing; rotor and image plane; and rotor, wing and image plane. This last configuration models a tilt rotor. With a tilt rotor, the wing turns some of the rotor downwash inboard. When the flows meet, some of the flow is forced upward creating a fountain. Some of the fountain is ingested into the rotor disc. Rotor fountain interactions produce very unsteady impulsive noise to the rear of the aircraft. Configuration changes to investigate download reduction included increasing the rotor/wing separation, deflecting the flap, adding the nacelle, adding vortex trapping plates and blowing on the upper surface. These configuration changes produced little or no effect on the noise, although they changed the net download. Increasing the wing span, however, reduced the annoying content of this impulse noise about 2dB.

Mosher, Marianne↗

Noise due to tip vortex formation on lifting rotors

The high frequency broadband noise radiated by the local separated flow at rotor blade tips is analyzed. The aeroacoustic model is based on the convection of the tip region's separated flow pressure fluctuations past the trailing edge of the blade. The tip vortex formation and separation are modeled from available experimental studies. The separated flow pressure fluctuations are estimated using available separated flow experimental data and correlations. The trailing edge noise was approximated using a point dipole model. The point dipole strengths were evaluated by a method based on the trailing edge noise theory of Amiet. The point dipole approach compares favorably to stationary airfoil trailing edge noise analyses and experiments except near the plane of the airfoil. The rotor tip separation noise results are compared to other noise mechanism calculations and to experiments. The tip noise mechanism is shown to be quite important in the high frequency range. It is likely to be the major contributor to high frequency broadband noise for heavily loaded rotors with low turbulence inflow.

George, A. R.↗

Noise and performance characteristics of a model scale X-wing rotor system in hover

Noise data for the hover condition were measured for a 8 m diameter X-wing model rotor mounted on an outdoor whirl tower. The noise was found to be a function of operating condition, in general increasing with performance. The X-wing spectra obtained from narrowband and 1/3-octave band analyses were dominated by the blade passage frequency harmonics. The circulation control slot blowing produced 1 to 10 kHz broadband noise which exhibited a jet velocity to the 5.4 dependency. Under the rotor plane loading noise was dominant, except at low values of blade pressure ratio where a sharp decrease in the blade passage frequency harmonic levels was observed. In the rotor plane, the contribution of the broadband noise sources was greater than under the rotor plane. The X-wing rotor system in hover exhibited flexibility in operating conditions to achieve a specific level of performance. The high collective, low blade passage ratio combinations which meet a given level of performance were associated with low overall sound pressure levels.

Willshire, W. L., Jr.↗

Fan Noise Prediction

Aircraft noise emission level restrictions in and around airports continue to grow more stringent every few years. Thus, it is important to predict noise emissions from aircraft accurately. Predicting noise from the engine(s) is an integral part of the efforts to characterize the noise signature of an aircraft. An important source of engine noise is the rotor-stator interaction noise produced as a result of impingement of fan rotor wakes on the fan exit guide vanes. Interaction noise propagates through the inlet and exhaust ducts of the engine and radiates to the far field. noise levels for a range of model fans stages that represent current aircraft engine designs. Eversman's radiation codes calculate both the inlet and exhaust noise radiation by propagating the internally measured rotor-stator interaction noise to the far field. Predicted far field sound pressure levels are then compared to the measured levels from wind tunnel tests. This effort's objective is to prove that the predicted levels actually describe the measured levels.

France, Joshua I.↗

Open Rotor Research at NASA Glenn

A low-noise open rotor system is being tested in collaboration with General Electric and CFM International, a 50/50 joint company between Snecma and GE. Candidate technologies for lower noise will be investigated as well as installation effects such as pylon integration. The research program in both the low and high-speed wind tunnels is reviewed. Some detailed flowfield and acoustics measurements acquired for an internal NASA program are highlighted. The publically available research data is presented also.

VanZante, Dale E.↗

Effect of inlet disturbances on fan inlet noise during a static test

Measurements of fan rotor inlet noise taken during static test situations are at variance with aircraft engine flight data. In particular, static tests generally yield a significantly higher tone at blade passage frequency than that measured during flight. To explain this discrepancy, the extent of the influence of inlet ground vortices and large-scale inlet turbulence on the forward-radiated fan noise measured at a static test facility was investigated. While such inlet disturbances were generated intentionally in an anechoic test chamber, far-field acoustic measurements and inlet flow-field hot-film mappings of a fan rotor were obtained. Experimental results indicate that the acoustic effect of such disturbances appears to be less severe for supersonic than for subsonic tip speeds. Further, a reverse flow that occurs on the exterior cowl in static test facilities appears to be an additional prime candidate for creating inlet disturbances and causing variance between flight and static acoustic data.

Bekofske, K. L.↗

Broadband Noise Prediction of Two Small Hovering Rotors using FUN3D-ANOPP2

A computational study was performed on two small hovering rotors, the ideally twisted rotor and the optimum hovering 2-bladed rotor, using FUN3D-ANOPP2. The effects of different inviscid upwinding techniques and temporal resolutions on aerodynamic performance and acoustic prediction were compared against experimental data obtained in the Small Hover Anechoic Chamber facility at the NASA Langley Research Center. Decreasing the numerical dissipation with 𝜅 tuning or by using a higher-order inviscid flux reconstruction scheme was shown to improve aerodynamic performance predictions when compared to measured data for most cases. The effect of dissipation on the vorticity field was also seen to influence the amount of turbulence surrounding the vortex core of the first blade-vortex interaction (BVI), the coherence of the second and higher BVI vortex cores, and the downstream breakdown of the rotor wake for both rotor geometries. Tonal and broadband noise predictions from simulation cases with lower dissipation were seen to agree better with the experiment for the ideally twisted rotor, whereas temporal resolution differences had negligible impact on the broadband noise results. Similar fundamental BPF directivity patterns were obtained by all simulation cases for the optimum hovering 2-bladed rotor, while the most accurate 2*BPF directivity trend, compared to the experiment, was predicted by the lower-dissipation case at the coarse temporal resolution, albeit with an amplitude underprediction. Broadband noise spectral roll-off behavior was seen to occur at a higher frequency when using a finer temporal resolution for the optimum hovering 2-bladed rotor, unlike for the ideally twisted rotor geometry. The broadband noise prediction for the optimum hovering 2-bladed rotor from the higher-dissipation case at the coarse temporal resolution was also seen to predict a tone centered around approximately 8.5 kHz, which was similar in amplitude to the measured tone around 16.5 kHz.

Christopher S. Thurman↗

Method for predicting impulsive noise generated by wind turbine rotors

Large wind turbines can generate both broad band and impulsive noises. These noises can be controlled by proper choice of rotor design parameters such as rotor location with respect to the supporting tower, tower geometry and tip speed. A method was developed to calculate the impulsive noise generated when the wind turbine blade experiences air forces that are periodic functions of the rotational frequency. This phenomenon can occur when the blades operate in the wake of the support tower and the nonuniform velocity field near the ground due to wind shear. Results from this method were compared with measured sound spectra taken at locations of one to two rotor diameters from the DOE/NASA Mod-1 wind turbine. The calculated spectra generally agreed with the measured data in both the amplitude of the predominant harmonics and the roll of rate with frequency. Measured sound pressure levels far from the Mod-1 (15 rotor diameters), however, were higher than predicted. Simultaneous measurements in the near and far field indicated that the propagation effects could enhance the sound levels by more than 10 dB above that expected by spherical dispersion. These propagation effects are believed to be due to terrain and atmospheric characteristics of the Mod-1 site.

Viterna, L. A.↗

Helicopter model rotor-blade vortex interaction impulsive noise: Scalability and parametric variations

Acoustic data taken in the anechoic Deutsch-Niederlaendischer Windkanal (DNW) have documented the blade vortex interaction (BVI) impulsive noise radiated from a 1/7-scale model main rotor of the AH-1 series helicopter. Averaged model scale data were compared with averaged full scale, inflight acoustic data under similar nondimensional test conditions. At low advance ratios (mu = 0.164 to 0.194), the data scale remarkable well in level and waveform shape, and also duplicate the directivity pattern of BVI impulsive noise. At moderate advance ratios (mu = 0.224 to 0.270), the scaling deteriorates, suggesting that the model scale rotor is not adequately simulating the full scale BVI noise; presently, no proved explanation of this discrepancy exists. Carefully performed parametric variations over a complete matrix of testing conditions have shown that all of the four governing nondimensional parameters - tip Mach number at hover, advance ratio, local inflow ratio, and thrust coefficient - are highly sensitive to BVI noise radiation.

Splettstoesser, W. R.↗

Helicopter model rotor-blade vortex interaction impulsive noise - Scalability and parametric variations

Acoustic data taken in the anechoic Deutsch-Niederlaendischer Windkanal (DNW) have documented the blade vortex interaction (BVI) impulsive noise radiated from a 1/7-scale model main rotor of the AH-1 series helicopter. Averaged model scale data were compared with averaged full scale, inflight acoustic data under similar nondimensional test conditions. At low advance ratios (mu = 0.164 to 0.194), the data scale remarkable well in level and waveform shape, and also duplicate the directivity pattern of BVI impulsive noise. At moderate advance ratios (mu = 0.224 to 0.270), the scalig deteriorates, suggesting that the model scale rotor is not adequately simulating the full scale BVI noise; presently, no proved explanation of this discrepancy exists. Carefully performed parametric variations over a complete matrix of testing conditions have shown that all of the four governing nondimensional parameters - tip Mach number at hover, advance ratio, local inflow ratio, and thrust coefficient - are highly sensitive to BVI noise radiation.

Boxwell, D. A.↗