Search NASA⌕ Search

SEARCH · Search NASA

Results for “STABILITY, DIRECTIONAL - DYNAMIC”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Improved Woodward's panel method for calculating edge suction forces

A new technique to improve Woodward's (1968) unified subsonic and supersonic panel method is described. The pressure prediction is improved based on a new two-dimensional theory. The method used by Lan (1977) is then used to calculate the leading-edge and side-edge suction forces by direct use of the predicted pressure distribution. The method is applicable to both subsonic and supersonic flow. It is shown that the improved Woodward panel method is capable of accurately predicting leading-edge and side-edge suction forces in subsonic and supersonic flow. Therefore, the method can be used not only to predict the vortex lift of complex planforms through the method of suction analogy, but also to calculate some lateral-directional stability derivatives.

Lan, C. E.↗
NASA NTRS1979

On the natural remanent magnetism of certain mare basalts

The natural remanent magnetization (NRM) and magnetic properties of five fine-grain mare basalts were investigated. The NRM of two vitrophyres has a large soft component, and the directional stability during AF demagnetization is poor. The remaining samples have NRM which is too soft to be of thermal origin and yet too hard to be simply isothermal contamination. It is suggested that the NRM of the samples could be shock remanent magnetization.

Fuller, M.↗
NASA NTRS1980

Stall/spin flight results for the remotely piloted spin research vehicle

The unmanned, remotely piloted, unpowered, spin research vehicle was used to evaluate the effects of the nose boom and of a wind tunnel-designed nose strake on the vehicle's stall/spin characteristics. The flight-determined directional stability derivatives and the attempted spin entries indicated that the vehicle with a nose strake had increased resistance to departure and spin. The acquisition of high quality steady spin data for this vehicle was made possible by the remotely piloted technique. The zero control smooth spin modes were found to be highly repeatable for a given configuration and to vary with forebody configuration. Several spin recovery techniques, including a nose parachute, are also evaluated.

Iliff, K. W.↗
NASA NTRS1980

Results of a low-speed wind tunnel test of the MDC 2.2M supersonic cruise aircraft configuration

Results of a low speed test conducted in the Full Scale Tunnel at NASA Langley using an advanced supersonic cruise vehicle configuration are presented. These tests used a 10 percent scale model of a configuration that had demonstrated high aerodynamic performance at Mach 2.2 during a previous test program. The low speed model has leading and trailing edge flaps designed to improve low speed lift to drag ratios at high lift and includes devices for longitudinal and lateral/directional control. The results obtained during the low speed test program have shown that full span leading edge flaps are required for maximum performance. The amount of deflection of the leading edge flap must increase with C sub L to obtain the maximum benefit. Over 80 percent of full leading edge suction was obtained up to lift off C sub L's of 0.65. A mild pitch up occurred at about 6 deg angle of attack with and without the leading edge flap deflected. The pitch up is controllable with the horizontal tail. Spoilers were found to be preferable to spoiler/deflectors at low speeds. The vertical tail maintained effectiveness up to the highest angle of attack tested but the tail on directional stability deteriorated at high angles of attack. Lateral control was adequate for landing at 72 m/sec in a 15.4 m/sec crosswind.

Yip, L. P.↗
NASA NTRS1982

Development of a simple, self-contained flight test data acquisition system

The flight test system described combines state-of-the-art microprocessor technology and high accuracy instrumentation with parameter identification technology which minimize data and flight time requirements. The system was designed to avoid permanent modifications of the test airplane and allow quick installation. It is capable of longitudinal and lateral-directional stability and control derivative estimation. Details of this system, calibration and flight test procedures, and the results of the Cessna 172 flight test program are presented. The system proved easy to install, simple to operate, and capable of accurate estimation of stability and control parameters in the Cessna 172 flight tests.

Clarke, R.↗
NASA NTRS1982

The development of aerodynamic uncertainties for the Space Shuttle Orbiter

The methodology involved in developing the ability to reproduce aerodynamic results between various wind tunnel tests and to determine uncertainties due to differences between preflight aerodynamic predictions and flight results derived from analysis of past aircraft programs is presented. The uncertainties were developed for pitching moment, lateral-directional stability, rudder power, and aileron power, and were formulated to yield aerodynamic uncertainties for an orbital, manned first flight. The compressed development schedule required the aerodynamics results from wind tunnel tests be equipped with tolerances, which accounted for reasonable changes in the vehicle configuration. A worst case scenario was decided on, with the results that every prediction included the widest possible aerodynamic margins. Repeatibility was emphasized between wind tunnel model tests, and was achieved with an accuracy of 0.006 with inclusion of Reynolds effects.

Young, J. C.↗
NASA NTRS1982

A simple, low cost application of a flight test parameter identification system

The flight test system combines state-of-the-art microprocessor technology and high accuracy instrumentation with parameter identification technology which minimize data and flight time requirements. The system was designed to avoid permanent modifications of the test airplane and allow quick installation. It is capable of longitudinal and lateral-directional stability and control derivative estimation. This paper presents details of this system, calibration and flight test procedures, and the results of the Cessna 172 flight test program. The system has proven easy to install, simple to operate, and capable of accurate estimation of stability and control parameters in the Cessna 172 flight tests.

Clarke, R.↗
NASA NTRS1983

The development of aerodynamic uncertainties for the space shuttle orbiter

The Shuttle Program development schedule and the management decision to perform an orbital, manned mission on the first launch resulted in a requirement to develop realistic aerodynamic uncertainties for the preflight aerodynamic predictions. This paper addresses the methodology in developing two types of aerodynamic uncertainties. One involves the ability to reproduce aerodynamic results between various wind tunnel tests. The second addresses the difference between preflight aerodynamic predictions and flight results derived from analysis of past aircraft programs. Both types of uncertainties for pitching moment, lateral-directional stability, rudder power, and aileron power are presented. In addition, the application of uncertainties to flight control design and fight test planning is briefly reviewed.

Young, J. C.↗
NASA NTRS1984

Some aerodynamic considerations for advanced aircraft configurations

Recent NASA wind-tunnel investigations of advanced unconventional configurations are surveyed, with an emphasis on those applicable to general-aviation aircraft. Photographs of typical models and graphs of aerodynamic parameters are provided. The designs discussed include aft installation of tractor or pusher-propellor engines; forward-swept wings; canards; combinations of canard, wing, and horizontal tail; and propeller-over-the-wing configurations. Consideration is given to canard-wing flow-field interactions, natural laminar flow, the choice of canard airfoil, directional stability and control, and propulsion-system location.

Williams, L. J.↗
NASA NTRS1984

The lateral-directional characteristics of a 74-degree Delta wing employing gothic planform vortex flaps

The low speed lateral/directional characteristics of a generic 74 degree delta wing body configuration employing the latest generation, gothic planform vortex flaps was determined. Longitudinal effects are also presented. The data are compared with theoretical estimates from VORSTAB, an extension of the Quasi vortex lattice Method of Lan which empirically accounts for vortex breakdown effects in the calculation of longitudinal and lateral/directional aerodynamic characteristics. It is indicated that leading edge deflections of 30 and 40 degrees reduce the magnitude of the wing effective dihedral relative to the baseline for a specified angle of attack or lift coefficient. For angles of attack greater than 15 degrees, these flap deflections reduce the configuration directional stability despite improved vertical tail effectiveness. It is shown that asymmetric leading edge deflections are inferior to conventional ailerons in generating rolling moments. VORSTAB calculations provide coarse lateral/directional estimates at low to moderate angles of attack. The theory does not account for vortex flow induced, vertical tail effects.

Grantz, A. C.↗
NASA NTRS1985

Low-speed experimental study of the vortex flow effects of a fighter forebody having unconventional cross-section

A low speed wind tunnel investigation is conducted for the vortex flow characteristics of a tailless fighter configuration that features full length, fuselage-blended forebody strakes. Static pressure distributions were obtained on the forebody upper surface, and six-component forces and moments were measured on the complete, 60-deg cropped delta wing-fuselage-centerline vertical fin model at angles of attack and sideslip respectively reaching 50 deg and + or - 20 deg. The surface pressure data reveal that development of concentrated vortices from the sharp edged forebody strakes occurred at moderate and high angles of attack. The blended forebody was effective in capturing the windward vortical flow up to high incidence and sideslip angles. The direct suction effect of the windward vortex on the forebody sidewall was the primary contributor to static directional stability at high angles of attack. These improvements are potentially offset, however, by reduced or unstable roll and yaw damping.

Erickson, G. E.↗
NASA NTRS1986

Hypersonic aerodynamic characteristics of a candidate entry research vehicle

Static longitudinal and lateral-directional aerodynamic characteristics of a candidate lifting entry research vehicle were measured at Mach numbers of 6 and 10 in air and at Mach 20 in helium. The effects of nose bluntness, body flap deflection, and elevon deflection were examined over a range of angle of attack. The vehicle demonstrated static longitudinal and lateral-directional stability at angles of attack from the maximum lift-to-drag ratio (L/D)max to high angles of attack. Sufficient control effectiveness existed to provide longitudinal trim from (L/D)max to high angles of attack. Aerodynamic coefficients predicted using the Hypersonic Arbitrary Body Program were compared to measurement. Good agreement was obtained for lift-to-drag values.

Brauckmann, G. J.↗
NASA NTRS1986

Some effects of interference flow fields on supersonic configurations

A summary of selected results for various basic research models is presented in order to illustrate some effects of interference flow fields at supersonic speeds. Some general effects of wings and tails on typical cruciform missile configurations are shown. Several arrangements of cruise-type missile concepts are presented to show the effects of added body volume on the lift-drag ratio. In addition, the effects of several tail arrangements and some effects of body cross-section on the directional stability characteristics are included.

Spearman, M. L.↗
NASA NTRS1988

Configuration trade and code validation study on a conical hypersonic vehicle

A study has been conducted on a generic wing-cone transatmospheric vehicle at Mach numbers form 2.5 to 4.5. The objectives of the study were to experimentally define the aerodynamic characteristics of the vehicle and evaluate several computational aerodynamic prediction methods through comparison with the experimental results. The baseline wing-cone configuration fuselage consisted of a 5 deg half-angle cone forebody, cylindrical midbody, and 9 deg truncated cone afterbody. The 4-percent-thick diamond airfoil wing had an aspect ratio of 1. Several configuration variables were investigated to provide trade information on canard, wing-position and incidence, vertical tail, and nose bluntness effects. Results of the study show that wing-position and wing-incidence effects on the longitudinal aerodynamic characteristics can be significantly influenced by wing-body interference. The use of positive wing incidence to provide favorable forebody orientation for possible inlet performance improvement is accompanied by trim drag and lift-drag ratio penalties. The lateral-directional stability characteristics were strongly influenced by the location of the vertical tails. The higher-order full-potential method provided better estimates of the aerodynamic characteristics than either the linearized supersonic potential method or the tangent-cone/tangent-wedge/shock-expansion on method.

Covell, Peter F.↗
NASA NTRS1989

Sheared wing-tip aerodynamics - Wind-tunnel and computational investigation

Computational and experimental performance benefits are presented for a high-aspect-ratio unswept wing configuration with sheared tips. The sheared tip is a highly swept and highly tapered surface located in the same plane as the inboard wing panel to which it is attached. The compuational results were obtained with an inviscid surface panel method that models the nonlinear influence of the trailing wake. Both wind-tunnel and calculated results were obtained for a 12-ft span wing model with various wing-tip configurations. The computational and experimental data are in fair agreement and demonstrate that sheared wing tips can reduce induced drag at cruise and climb lift coefficients. The drag reduction is the result of wake deformation effects and changes in spanwise load distribution. Wind-tunnel measured longitudinal and lateral directional stability characteristics are also presented for the various wing-tip layouts.

Vijgen, P. M. H. W.↗
NASA NTRS1991

Aerodynamic characteristics of the HL-20 and HL-20A lifting-body configurations

The data show that the HL-20 is longitudinally and laterally stable over the test range from Mach 10 to 0.2. At hypersonic speeds it has a trimmed lift/drag ratio of 1.4. This values gives the vehicle a cross range capability similar to that of the Space Shuttle. At subsonic speeds, the HL-20 has a trimmed lift/drag ratio of about 3.6. Replacing the flat plate outboard fins with fins having an airfoil shape, increased the maximum trimmed L/D to 4.3. Preliminary evaluation of configuration modifications (the HL-20A series), indicates that trim at higher values of lift at hypersonic speeds could be achieved with an L/D of about 1.0. In the supersonic range, the lift and directional stability characteristics were improved. The untrimmed subsonic L/D was increased to 5.8 with airfoil fins.

Ware, George M.↗
NASA NTRS1992

Longitudinal and lateral-directional aerodynamic characteristics of a wing-cone configuration at Mach numbers from 2.5 to 4.5

A study was conducted to determine the longitudinal and lateral-directional aerodynamic characteristics of a generic wing-cone configuration at supersonic speeds. The fuselage has a 5 deg half-angle cone forebody, cylindrical midbody, and a 9 deg truncated cone afterbody. The delta wing (aspect ratio 1.0) had a 4 pct. thick diamond airfoil section. The tests were made in the Langley Unitary Plan Wind Tunnel at Mach numbers from 2.50 and 4.50. Angle of attack was varied from -4 to 28 degs, and angle of sideslip varied from -8 to 8 degs. Several configurations were studied to determine the effects of variations in wing longitudinal position, wing incidence, vertical tail configuration, canard shape, and nose bluntness. Typical effects of Reynolds number and Mach number on the longitudinal characteristics were observed. The incremental effects of the configuration variables were generally unaffected by Mach number. The directional stability characteristics of the large and small centerline mounted vertical tail configurations were significantly degraded with increasing angle of attack and Mach number.

Covell, Peter F.↗
NASA NTRS1991

Hub and pylon fairing integration for helicopter drag reduction

The results of testing hub and pylon fairings mounted on a one-fifth scale helicopter with the goal of reducing parasite drag are presented. Lift, drag, and pitching moment, as well as side force and yawing moment, were measured. The primary objective of the test was to validate the drag reduction capability of integrated hub and pylon configurations in the aerodynamic environment produced by a rotating hub in forward flight. In addition to the baseline helicopter without fairings, three hub fairings and three pylon fairings were tested in various combinations. The three hub fairings tested reflect two different conceptual design approaches to implementing an integrated fairing configuration on an actual aircraft. The design philosophy is discussed in detail and comparisons are made between the wind tunnel models and potential full-scale prototypes. The data show that model drag can be reduced by as much as 20.8 percent by combining a small hub fairing with circular arc upper and flat lower surfaces and a nontapered 34-percent thick pylon fairing. Aerodynamic effects caused by the fairings, which may have a significant impact on static longitudinal and directional stability, were observed. The results support previous research which showed that the greatest reduction in model drag is achieved if the hub and pylon fairings are integrated with minimum gap between the two.

Martin, D. M.↗