SEARCH · Search NASA

Results for “SURFACE DIFFUSION EFFECT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

All sources NASA NTRS DOE OSTI

NASA NTRS1979

Silicon solar cell fabrication technology

The laser cell scanner was used to characterize a number of solar cells made in various materials. An electron beam-induced current (EBIC) study was performed using a stereoscan scanning electron microscope. Planar p-n junctions were analyzed. A theory for the EBIC based on the analytical solution of the ambipolar diffusion equation under the influence of electron beam excitation parameter z (which is related to beam penetration), the junction depth Z sub j, the beam current and the surface recombination, was formulated and tested. The effect of a grain boundary was studied.

Stafsudd, O. M.↗

NASA NTRS1978

Infrared Astronomical Satellite (IRAS) analysis, introduction

Stray light transmittance analysis on a design of the Infrared Astronomical Satellite (IRAS) is presented. The system was evaluated for scattered radiation propagation with the use of the APART (Arizon's Paraxial Analysis of Radiation Transfer), and the propagation of diffracted energy with both PADE (Paraxial Analysis of Diffracted Energy) and the GUERAP II programs. The scattered radiation analysis was performed by using both a 5% diffuse black on the baffle and vane surfaces and by using a mathematical model of the Martin Black scattering characteristics. The sources of infrared radiation and of radiation in the visible wavelengths are identified. Diffraction effects are dominant only at the large off-axis angles, except for a few specific cases and smaller angles. At the longer wavelengths the diffraction contributions go up significantly. It is the comparative increase which determines which propagation process predominates. Combined transmittance values are presented.

Source record↗

NASA NTRS1991

Solar radiation for Mars power systems

Detailed information about the solar radiation characteristics on Mars are necessary for effective design of future planned solar energy systems operating on the surface of Mars. A procedure and solar radiation related data from which the diurnally and daily variation of the global, direct (or beam), and diffuse insolation on Mars are calculated, are presented. The radiation data are based on measured optical depth of the Martian atmosphere derived from images taken of the Sun with a special diode on the Viking Lander cameras; and computation based on multiple wavelength and multiple scattering of the solar radiation.

Appelbaum, Joseph↗

NASA NTRS2008

Non-steady Reconnection in Global Simulations of Magnetosphere Dynamics

To analyze the non-steady magnetic reconnection during quasi-steady solar wind driving we employed high resolution global MHD model BATSRUS with non-MHD corrections in diffusion regions around the reconnection sites. To clarify the role of small-scale non-MHD effects on the global magnetospheric dynamic we performed simulations with different models of dissipation. We found that magnetopause surface is not in steady state even during extended periods of steady solar wind conditions. The so-called tilted reconnection lines become unstable due to formation of pressure bubbles, strong core field flux tubes, vortices, and traveling magnetic field cavities. Non-steady dayside reconnection results in formation of flux tubes with bended axis magnetically connecting magnetic field cavities generated at flanks and strong core segments formed near the subsolar region. We found that the rate of magnetic flux loading to the tail lobes is not very sensitive to the dissipation mechanism and details of the dayside reconnection. On the other hand the magnetotail reconnection rate, the speed of the reconnection site retreat and the global magnetotail dynamics strongly depend on the model of dissipation. THEMIS and Cluster observations are consistent with signatures predicted by simulations.

Kuznetsova, M. M.↗

NASA NTRS2009

Sources of Sodium in the Lunar Exosphere: Modeling Using Ground-Based Observations of Sodium Emission and Spacecraft Data of the Plasma

Observations of the equatorial lunar sodium emission are examined to quantify the effect of precipitating ions on source rates for the Moon's exospheric volatile species. Using a model of exospheric sodium transport under lunar gravity forces, the measured emission intensity is normalized to a constant lunar phase angle to minimize the effect of different viewing geometries. Daily averages of the solar Lyman alpha flux and ion flux are used as the input variables for photon-stimulated desorption (PSD) and ion sputtering, respectively, while impact vaporization due to the micrometeoritic influx is assumed constant. Additionally, a proxy term proportional to both the Lyman alpha and to the ion flux is introduced to assess the importance of ion-enhanced diffusion and/or chemical sputtering. The combination of particle transport and constrained regression models demonstrates that, assuming sputtering yields that are typical of protons incident on lunar soils, the primary effect of ion impact on the surface of the Moon is not direct sputtering but rather an enhancement of the PSD efficiency. It is inferred that the ion-induced effects must double the PSD efficiency for flux typical of the solar wind at 1 AU. The enhancement in relative efficiency of PSD due to the bombardment of the lunar surface by the plasma sheet ions during passages through the Earth's magnetotail is shown to be approximately two times higher than when it is due to solar wind ions. This leads to the conclusion that the priming of the surface is more efficiently carried out by the energetic plasma sheet ions.

Sarantos, Menelaos↗

NASA NTRS2022

Comparable Bulk Radar Attenuation Characteristics Across Both Martian Polar Layered Deposits

The dust-laden and predominantly water ice south polar layered deposits (SPLD) exhibit unique radar behavior at Shallow Radar (SHARAD) frequencies that is not seen in the NPLD. A vertically extensive scattering phenomenon leads to diffuse echoes that obscure radar stratigraphy within the SPLD, referred to as “fog.” Here, we use 2-D and 3-D SHARAD data to measure the areal extent in which the SPLD basal interface can be identified. We also measure reflected power of SPLD basal reflectors and compare those values to ice thickness, regional geomorphology, and the presence of radar echo scattering, to constrain any influence these factors may have on the propagation of radio waves and detectability of the base. Approximately 33% of the area in which the basal interface is observed in Mars Advanced Radar for Subsurface and Ionosphere Sounding data is also detected in SHARAD data. As expected, basal power shows a negative correlation with ice thickness, but the effects of radar fog are less clear. Areas of “column” radar fog patterns exhibit higher average basal power values than regions without radar fog, and areas with only near-surface radar fog have the lowest average basal power values. Our study results suggest that these diffuse echoes may not be associated with radio wave attenuation. Average loss tangent for the SPLD (0.0019 ± 0.0012) indicates no distinguishable difference from previously reported NPLD values in terms of bulk loss properties. We speculate that the SPLD's infrequent reflections compared to the NPLD may be due to the former's dust being less densely packed together to facilitate radar detection.

N Abu Hashmeh↗

NASA NTRS1979

Modeling of thin, back-wall silicon solar cells

The performance of silicon solar cells with p-n junctions on the nonilluminated surface (i.e., upside-down or back-wall cells) was calculated. These structures consisted of a uniformly shaped p-type substrate layer, a p(+)-type field layer on the front (illuminated) surface, and a shallow, n-type junction on the back (nonilluminated) surface. A four-layer solar cell model was used to calculate efficiency, open-circuit voltage, and short-circuit current. The effect on performance of p-layer thickness and resistivity was determined. The diffusion length was varied to simulate the effect of radiation damage. The results show that peak initial efficiencies greater than 15 percent are possible for cell thicknesses or 100 micrometers or less. After 10 years of radiation damage in geosynchronous orbit, thin (25 to 50 micrometers thick) cells made from 10 to 100 ohm cm material show the smallest decrease (approximately 10 percent) in performance.

Baraona, C. R.↗

NASA NTRS1984

A generalized behavioral model for rotating short period comets with spectral orbital elements and axial orientation

A generalized model for short period comets is developed which integrates in a fairly rigorous manner the isolation history of regions on rotating comets with specified axial orientation and the complex feedback processes involving heat, gas and dust transport, dust mantle development and coma opacity. Attention is focused on development, reconfiguration and partial or complete launching of dust mantles and the reciprocal effects of these three processes on ice surface temperature and gas and dust production. The dust mantle controls the H2O flux not only by its effect on the temperature at the ice interface but (dominantly) by its dynamic stability which strongly influences vapor diffusivity. The model includes the effects of latitude, rotation and spin axis orientation are included and applied to an initially homogeneous sphere of H2O ice and silicate using the orbital parameters of comet Encke. Numerous variations of the model, using combinations of grain size distribution, dust-to-ice ratio, latitude and spin axis orientation, are presented and discussed. Resulted for a similar nonrotating, constant Sun orientation models are also included.

Fanale, F. P.↗

NASA NTRS1999

A Validated All-Pressure Fluid Drop Model and Lewis Number Effects for a Binary Mixture

The differences between subcritical liquid drop and supercritical fluid drop behavior are discussed. Under subcritical, evaporative high emission rate conditions, a film layer is present in the inner part of the drop surface which contributes to the unique determination of the boundary conditions; it is this film layer which contributes to the solution's convective-diffusive character. In contrast, under supercritical condition as the boundary conditions contain a degree of arbitrariness due to the absence of a surface, and the solution has then a purely diffusive character. Results from simulations of a free fluid drop under no-gravity conditions are compared to microgravity experimental data from suspended, large drop experiments at high, low and intermediary temperatures and in a range of pressures encompassing the sub-and supercritical regime. Despite the difference between the conditions of the simulations and experiments (suspension vs. free floating), the time rate of variation of the drop diameter square is remarkably well predicted in the linear curve regime. The drop diameter is determined in the simulations from the location of the maximum density gradient, and agrees well with the data. It is also shown that the classical calculation of the Lewis number gives qualitatively erroneous results at supercritical conditions, but that an effective Lewis number previously defined gives qualitatively correct estimates of the length scales for heat and mass transfer at all pressures.

Harstad, K.↗

NASA NTRS1973

ERTS-1 anomalous dark patches

The author has identified the following significant results. Through combined use of imagery from ERTS-1 and NOAA-2 satellites was found that when the sun elevation exceeds 55 degrees, the ERTS-1 imagery is subject to considerable contamination by sunlight even though the actual specular point is nearly 300 nautical miles from nadir. Based on sea surface wave slope information, a wind speed of 10 knots will theoretically provide approximately 0.5 percent incident solar reflectance under observed ERTS multispectral scanner detectors. This reflectance nearly doubles under the influence of a 20 knot wind. The most pronounced effect occurs in areas of calm water where anomalous dark patches are observed. Calm water at distances from the specular point found in ERTS scenes will reflect no solar energy to the multispectral scanner, making these regions stand out as dark areas in all bands in an ocean scene otherwise comprosed by a general diffuse sunlight from rougher ocean surfaces. Anomalous dark patches in the outer parts of the glitter zones may explain the unusual appearance of some scenes.

Strong, A. E.↗

NASA NTRS1962

Pitfalls in thermal emission studies

Attention is called to several pitfalls that often beset investigators who make thermal emittance studies. The pitfalls mentioned include the following: (1) conflicting meanings of several frequently used terms as found in the literature, each meaning having authoritative sponsorship; (2) incomplete and hence potentially misleading descriptions of specimens on which reported data arc based; (3) reference to emissivity or remittance as a property of a surface rather than a volume property (influenced by the surface); (4) occasional omission of diffuse reflection from analyses of the optical properties of inhomogeneous bodies; (5) failure to observe the restrictions upon conditions that are required for validity of basic equations; (6)uncertainties as to the effective temperature, peculiar to specimens having low absorption indices; and (7) lack of suitable physical standards. Several suggestions are made for avoiding or minimizing the consequences of the pitfalls discussed.

THERMAL RADIATION↗

NASA NTRS1990

Solar radiation on Mars: Update 1990

Detailed information on solar radiation characteristics on Mars are necessary for effective design of future planned solar energy systems operating on the surface of Mars. The authors present a procedure and solar radiation related data from which the diurnally and daily variation of the global, direct beam and diffuse insolation on Mars are calculated. The radiation data are based on measured optical depth of the Martian atmosphere derived from images taken of the Sun with a special diode on the Viking Lander cameras and computation based on multiple wavelength and multiple scattering of the solar radiation. This work is an update to NASA-TM-102299 and includes a refinement of the solar radiation model.

Appelbaum, Joseph↗

NASA NTRS1993

Uncertainty analysis of diffuse-gray radiation enclosure problems: A hypersensitive case study

An uncertainty analysis of diffuse-gray enclosure problems is presented. The genesis was a diffuse-gray enclosure problem which proved to be hypersensitive to the specification of view factors. This genesis is discussed in some detail. The uncertainty analysis is presented for the general diffuse-gray enclosure problem and applied to the hypersensitive case study. It was found that the hypersensitivity could be greatly reduced by enforcing both closure and reciprocity for the view factors. The effects of uncertainties in the surface emissivities and temperatures are also investigated.

Taylor, Robert P.↗

NASA NTRS2005

Experimental Investigation of a Morphing Nacelle Ducted Fan

The application of Circulation Control to the nacelle of a shrouded fan is proposed as a means to enhance off-design performance of the shrouded fan. Typically, a fixed geometry shroud is efficient at a single operating condition. Modifying circulation about the fixed geometry is proposed as a means to virtually morph the shroud without moving surfaces. This approach will enhance off-design-point performance with minimal complexity, weight, and cost. Termed the Morphing Nacelle, this concept provides an attractive propulsion option for Vertical Take-off and Landing (VTOL) aircraft, such conceptual Personal Air Vehicle (PAV) configurations proposed by NASA. An experimental proof of concept investigation of the Morphing Nacelle is detailed in this paper. A powered model shrouded fan model was constructed with Circulation Control (CC) devices integrated in the inlet and exit of the nacelle. Both CC devices consisted of an annular jet slot directing a jet sheet tangent to a curved surface, generally described as a Coanda surface. The model shroud was tailored for axial flight, with a diffusing inlet, but was operated off-design condition as a static lifting fan. Thrust stand experiments were conducted to determine if the CC devices could effectively improve off-design performance of the shrouded fan. Additional tests were conducted to explore the effectiveness of the CC devices a means to reduce peak static pressure on the ground below a lifting fan. Experimental results showed that off-design static thrust performance of the model was improved when the CC devices were employed under certain conditions. The exhaust CC device alone, while effective in diffusing the fan exhaust and improving weight flow into shroud inlet, tended to diminish performance of the fan with increased CC jet momentum. The inlet CC device was effective at reattaching a normally stalled inlet flow condition, proving an effective means of enhancing performance. A more dramatic improvement in static thrust was obtained when the inlet and exit CC devices were operated in unison, but only over a limited range of CC jet momentum. Operating the nacelle inlet and exit CC devices together proved very effective in reducing peak ground plane static pressure, while maintaining static thrust. The Morphing Nacelle concept proved effective at enhancing off-design performance of the model; however, additional investigation is necessary to generalize the results.

Kondor, Shayne A.↗

NASA NTRS2002

Modelling the effect of diffuse light on canopy photosynthesis in controlled environments

A layered canopy model was used to analyze the effects of diffuse light on canopy gross photosynthesis in controlled environment plant growth chambers, where, in contrast to the field, highly diffuse light can occur at high irradiance. The model suggests that high diffuse light fractions (approximately 0.7) and irradiance (1400 micromoles m-2 s-1) may enhance crop life-cycle canopy gross photosynthesis for hydroponic wheat by about 20% compared to direct light at the same irradiance. Our simulations suggest that high accuracy is not needed in specifying diffuse light fractions in chambers between approximately 0.7 and 1, because simulated photosynthesis for closed canopies plateau in this range. We also examined the effect of leaf angle distribution on canopy photosynthesis under growth chamber conditions, as these distributions determine canopy extinction coefficients for direct and diffuse light. We show that the spherical leaf angle distribution is not suitable for modeling photosynthesis of planophile canopies (e.g., soybean and peanut) in growth chambers. Also, the absorption of the light reflected from the surface below the canopy should generally be included in model simulations, as the corresponding albedo values in the photosynthetically active range may be quite high in growth chambers (e.g., approximately 0.5). In addition to the modeling implications, our results suggest that diffuse light conditions should be considered when drawing conclusions from experiments in controlled environments.

Non-NASA Center↗

NASA NTRS1973

A new electric field effect in silicon solar cells.

The phenomenon of high-resistivity silicon solar cells manifesting high open-circuit voltages previously observed only for cells made from low-resistivity silicon is shown to be caused by the presence of a shallow diffused region at the back surface of the cell. The basic cell structure is either n+, p, p+ or p+, n, n+. The high open-circuit voltage arises from the injection and accumulation of excess majority carriers in the bulk upon illumination or application of forward bias to the structure. A working model for the cell, designated a back surface field (BSF) cell, is described, and recent developments are cited.

Mandelkorn, J.↗

NASA NTRS1975

Flow visualization of discrete hole film cooling for gas turbine applications

Film injection from discrete holes in a three row staggered array with 5-diameter spacing is studied for three different hole angles: (1) normal, (2) slanted 30 deg to the surface in the direction of the mainstream, and (3) slanted 30 deg to the surface and 45 deg laterally to the mainstream. The boundary layer thickness-to-hole diameter ratio and Reynolds number are typical of gas turbine film cooling applications. Two different injection locations are studied to evaluate the effect of boundary layer thickness on film penetration and mixing. Detailed streaklines showing the turbulent motion of the injected air are obtained by photographing very small neutrally buoyant helium filled 'soap' bubbles which follow the flow field. Unlike smoke, which diffuses rapidly in the high turbulent mixing region associated with discrete hole blowing, the bubble streaklines passing downstream injection locations are clearly identifiable and can be traced back to their origin. Visualization of surface temperature patterns obtained from infrared photographs of a similar film cooled surface are also included.

Colladay, R. S.↗

NASA NTRS1979

Reduction of intensity variations on a photovoltaic array with compound parabolic concentrators

The reduction of nonuniformities in the intensity distribution of light focused on a photovoltaic array by a compound parabolic concentrator is investigated. The introduction of small distortions into the surfaces of the reflector in order to diffuse the incident collimated light to fill the angular acceptance of the concentrator is calculated by means of ray tracing to decrease the irradiance nonuniformity at the cost of a lowered effective concentration of the concentrator. Measurements of the intensity distribution on a scale test model in terrestrial sunlight with corrugated aluminized mylar reflectors are shown to be in good agreement with the ray tracing results. A two-stage concentrator consisting of a focusing primary and a nonimaging secondary is also shown to result in a fairly uniform intensity distribution except in the case of a 4-deg incidence angle, which may be corrected by the introduction of distortions into one or both concentration stages.

Greenman, P.↗