Search NASA⌕ Search

SEARCH · Search NASA

Results for “Screw”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Effect of hydrogen on plasticity of $α$-Fe: A multi-scale assessment

A multi-scale study was carried out to quantify the effect of interstitial hydrogen concentration on plasticity in $α$-Fe. Here, in this work, the influence of hydrogen on the screw dislocation glide behavior was examined across several length-scales. The insights obtained were integrated to provide an accurate continuum description for the effect of hydrogen on the dislocation based plasticity in polycrystalline $α$-Fe. At the outset of this work, a new Fe—H interatomic potential was formulated that enhanced the atomistic estimation of the variation in dislocation glide behavior in presence of hydrogen. Next, the dislocation core reconstruction observed due to the addition of hydrogen using atomistic simulations was validated with the help of large-scale DFT calculations based on the DFT-FE framework. Several atomistic simulations were carried out to comprehensively quantify the effect of hydrogen on the non-Schmid behavior exhibited during the dislocation glide in $α$-Fe. Finally, crystal plasticity simulations were carried out to understand the effect of hydrogen on the meso-scale deformation behavior of polycrystalline $α$-Fe.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Compression molding of anisotropic NdFeB bonded magnets in a polycarbonate matrix

Anisotropic bonded Nd 2 Fe 14 B (NdFeB) magnets in a polycarbonate (PC) binder matrix are fabricated using a compression molding process. The weight fractions (w.f.) of NdFeB in PC on the batch mixer are 20, 50, 75, 85 and 95% compared to the twin screw extruder with 20, 50 and 75% respectively. The density of the 95% batch mixed magnets fabricated was 5.34 g/cm 3 and the magnetic properties are, intrinsic coercivity H ci = 942.99 kA/m, remanence B r = 0.86 T, and energy product (BH) max = 120.96 kJ/m 3 . Furthermore, the measured tensile properties are in the range of 27-59 MPa, comparable to that of polyamide (PA), polyphenylene sulfide (PPS) bonded magnets and demonstrating potential for bonded magnet applications. Scanning electron microscopy showed that the onset of failure occurs in the magnetic particle- matrix interface. This study demonstrates that compression additive molding technique can be used to fabricate high performance NdFeB polycarbonate composite magnets with improved mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Melt Processing Pretreatment Effects on Enzymatic Depolymerization of Poly(ethylene terephthalate)

Poly(ethylene terephthalate) (PET) is a common thermoplastic material, used in a wide variety of applications (i.e., bottles, fabrics, packaging, electronics, and automotive components). Increasing demand for PET has precipitated a need for improved recycling technology, especially for single-use PET waste. Recently, enzymatic depolymerization has shown promise as an environmentally responsible alternative for PET chemical recycling that yields economically useful products (e.g., terephthalic acid, adipic acid, and ethylene glycol). However, the depolymerization system still suffers from low rates on crystalline PET substrates, and effects of realistic waste streams are not known. In our work, PET waste is pretreated using an ultra-high-speed twin-screw extruder system. PET substrates were modified by various processing pretreatments to allow enzymes better access to depolymerize substrate materials. The effect of varying throughput and mechanical shear on structural properties of the PET waste was analyzed using molecular weight and thermal characterizations. These pretreated samples exhibit modifications in molecular weight, glass transition temperature, crystallinity, and specific surface area. The unpurified leaf-branch compost cutinase enzyme produced from the fed-batch fermentation of Escherichia coli BL21(DE3) was used in enzymatic depolymerization, where a faster reaction was observed as crystallinity was decreased and the specific surface area was increased. The rate of terephthalic acid production was also significantly higher for samples processed at lower mechanical shear with higher throughputs. As a result, this work demonstrates the potential for tailoring pretreatments in pursuit of faster and more energy efficient PET recycling using enzymes, with facile adaptation to the industrial scale for the circular economy.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Design of a Continuous Pellet Fueling System for Wendelstein 7-X

A continuous pellet fueling system (CPFS) is currently being designed at the Oak Ridge National Laboratory (ORNL) for the long pulse operation of the Wendelstein 7-X (W7-X) stellarator. The purpose of the CPFS is to provide deep continuous fueling for feedback-controlled high-density operation and mitigation of predicted hollow density profiles. As described here, the system will provide the capability to inject cylindrical pellets of solid hydrogen or deuterium into the plasma core, with flexibility to vary the pellet size, velocity, and injection frequency. Pellets are nominally of 3 mm in diameter and have a length between 1 and 4 mm. The heart of the CPFS is a vertically oriented, twin-screw extruder, cooled by three Gifford-McMahon cryocoolers in parallel, designed to form a continuous filament of hydrogen or deuterium. The filament width, which determines the pellet length, can be adjusted by means of a variable nozzle driven by a linear actuator at the base of the extruder. Coupled to the nozzle is a solenoid-operated gas gun and cutter assembly. A pneumatic propellant valve pulses a burst of ~60 bar helium to accelerate the cut pellet into W7-X. Three gaps in the guide tubes provide pumping locations to remove the helium propellant before it reaches the plasma. The maximum velocity of the pellet is limited by its ability to survive navigating the guide tube trajectory intact. A microwave cavity located within the guide tube provides the capability to measure the pellet size and velocity. The mechanical and thermal designs of the W7-X extruder, adjustable nozzle, and gun and cutter assembly design are described. A guide tube design and experimental pellet survivability test results are presented.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

RITE Gen5 KHPS Levelized Cost of Energy

Levelized Cost of Energy analysis for Verdant Power Gen5 KHPS utilizing annualized AEP based on actual energy generation at the RITE Project during 2020-21. The WEC devices analyzed include attenuator, point absorber, oscillating wave surge converter, oscillating water column, overtopping/terminator device, submerged pressure differential, bulge wave, and rotating mass type wave energy converter devices. The CEC devices analyzed include horizontal axis turbine, vertical axis turbine, oscillating hydrofoil, enclosed tips (Venturi), Archimedes screw, and tidal kite type current energy converter devices.

16 TIDAL AND WAVE POWER↗
DOE OSTI2020

Harnessing the Hydroelectric Potential of Engineered Drops (Final Technical Report)

The potential for low-head hydropower in the engineered drops in both federal and private irrigation system is well known and significant. The environmental and socio/recreational impacts of harnessing this renewable energy resource in man-made conduits are much less, and often insignificant, compared with comparable hydro-electric potential in natural water features on rivers, lakes, and streams. Yet, few new plants have been commissioned in more than two decades. Over the same time period, low head hydro installations in Germany have more than doubled. The challenge is in finding economical ways to harness the hydro-electric potential in the engineered drops, and efficiently deliver the power to the grid. The objectives of Percheron Power, LLC's (Percheron Power) Project were to design, develop, permit, and operate an innovative low-head hydro-electric generation facility on an existing engineered drop of a large irrigation canal system. The hydro-electric generation facility was designed to employ a new type of turbine and technology, called an Archimedes Hydrodynamic Screw (AHS), to harness the existing potential of the engineered drop. The goal was to demonstrate the new lower cost AHS technology system to federal agencies, irrigation districts and other system owners and to support further development of new small hydropower projects at previously marginal low-head sites in the U.S. The objective of this funding opportunity of the Department of Energy Water Power Technologies Office was to reduce the Levelized Cost of Energy (LCOE) for small hydropower to less than ${$}$0.07/kWh (${$}$70/MWh) to be competitive with existing base-load power sources such as coal-powered power plants.

13 HYDRO ENERGY↗
NASA NTRS1965

Cosmic chemistry.

Chemical nature and origin of solid particles formed in primordial solar nebula, examining growth mechanism based on screw dislocations present in preplanetary nebula

INTERPLANETARY DUST↗
DOE OSTI2020

Van der Waals Nanowires with Continuously Variable Interlayer Twist and Twist Homojunctions

Abstract Moiré patterns at van der Waals interfaces between twisted 2D crystals give rise to distinct optoelectronic excitations, as well as, narrowly dispersive bands responsible for correlated electron phenomena. Contrasting with the conventional, mechanically stacked planar twist moirés, recent work shows twisted van der Waals interfaces spontaneously formed in nanowires of layered crystals, where Eshelby twist due to axial screw dislocations stabilizes a chiral structure with small interlayer rotation. Here, the realization of tunable twist in germanium(II) sulfide (GeS) van der Waals nanowires is reported. Tapered nanowires host continuously variable interlayer twist. Homojunctions between dislocated (chiral) and defect‐free (achiral) segments are obtained by triggering the emission of axial dislocations during growth. Measurements across such junctions, implemented here using local absorption and luminescence spectroscopy, provide a convenient tool for detecting twist effects. The results identify a versatile system for 3D twistronics, probing moiré physics, and for realizing moiré architectures without equivalent in planar systems.

Sutter, Peter↗
DOE OSTI2021

Superior High-Temperature Strength in a Supersaturated Refractory High-Entropy Alloy

Refractory high-entropy alloys (RHEA) show promising applications at high temperatures. However, achieving high strengths at elevated temperatures above 1,173K is still challenging due to heat softening. Using intrinsic material characteristics as the alloy-design principles, a single-phase body-centered-cubic (BCC) CrMoNbV RHEA with high-temperature strengths (beyond 1,000 MPa at 1,273 K) is designed, superior to other reported RHEAs as well as conventional superalloys. The origin of the high-temperature strength is revealed by in-situ neutron scattering, transmission-electron microscopy, and first-principles calculations. The CrMoNbV’s elevated-temperature strength retention up to 1,273 K arises from its large atomic-size and elastic-modulus mismatches, the insensitive temperature dependence of elastic constants, and the dominance of non-screw character dislocations caused by the strong solute pinning, which makes the solid-solution strengthening pronounced. The alloy-design principles and the insights in this study pave the way to design RHEAs with outstanding high-temperature strength.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Circular Reprocessing of Thermoset Polyurethane Foams

Thermoset polyurethane (PU) foams are widely used in industrial applications, but they cannot be recycled by conventional melt reprocessing because of their cross-linked structures. The introduction of carbamate exchange catalysts converts thermoset PU into covalent adaptable networks (CANs), which are amenable to reprocessing at elevated temperatures. However, this approach has produced solid PU films, which have fewer uses and lower commercial demand. In this work, simultaneous reprocessing and refoaming of thermoset PU foams is demonstrated by leveraging the melt-processability of PU CANs and allowing cell growth by gas generation in a twin-screw extruder. The optimal operating temperature of the refoaming process is determined through chemical, thermal, and structural analysis of PU foam extrudates. The foam-to-foam extrusion process produces controllable, continuous, and uniform foam structures, as characterized by cell diameter and cell number density. Low-density PU foams are obtained through a process simulating injection molding. The compression properties of reprocessed PU foam are compared with as-synthesized PU foam to demonstrate efficacy of the refoaming processes. These results demonstrate that PU foams can be prepared through recycling while maintaining microstructural and chemical integrity. In the future, this strategy may be applied to thermoset PU foams of various chemical compositions and shows promise for scalability.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Pseudotunnel Magnetoresistance in Twisted van der Waals Fe 3 GeTe 2 Homojunctions

Abstract Twistronics, a novel engineering approach involving the alignment of van der Waals (vdW) integrated two‐dimensional materials at specific angles, has recently attracted significant attention. Novel nontrivial phenomena have been demonstrated in twisted vdW junctions (the so‐called magic angle), such as unconventional superconductivity, topological phases, and magnetism. However, there have been only few reports on integrated vdW layers with large twist angles θ t , such as twisted interfacial Josephson junctions using high‐temperature superconductors. Herein, vdW homojunctions of the thin‐magnetic flakes, Fe 3 GeTe 2 (FGT), with large θ t ranging from 0° to 90°, without inserting any tunnel barriers are assembled. Nevertheless, these vdW homojunctions exhibit tunnel‐magnetoresistance (TMR) like behavior (pseudo‐TMR (PTMR) effect) with the ratios highly sensitive to the θ t values, revealing that the vdW gap at the junction interface between the twisted FGT layers behaves like a tunnel barrier and the θ t serves a control parameter for PTMR by drastically varying magnitudes of the lattice‐mismatch and the subsequent appearance of antiferromagnetic (AFM) spin alignment. First‐principles calculations considering vacuum gaps indicate strong dependence of TMR on the θ t driven by the sixfold screw rotational symmetry of bulk FGT. The present homojunctions hold promise as a platform for novel AFM spin‐dependent phenomena and spintronic applications.

Obata, Reiji [Faculty of Science and Engineering A↗
DOE OSTI2025

Electronic Excitation‐Driven β‐Ga 2 O 3 Metastability Transformation and Self‐Organization Mechanism: β→κ/γ/δ Phases

Here, irradiation-driven multiphase self-organization presents emergent opportunities for the customization of nanoscale engineering properties, dynamically tuning strain-field distributions and interfacial electronic structures. Responding to intense electronic excitation-induced energy deposition, the dominant phase transformations, with varying Gibbs free energy $Δ,G^o_f$ are confirmed as β → κ → γ → δ that are located in specific microregions for Gallium (III) oxide (Ga 2 O 3 ), as follows: (i) Surface-localized interstitial accumulation under compressive stress triggers β → δ via semi-coherent interface formation. (ii) Tensile stress within latent tracks drives vacancy-mediated oxygen layer truncation (4/12 periodicity along ⟨0001⟩), stabilizing coherent 4H (ABCB) κ and 3C (ABC) β (ABC) interfaces through strain-compensated octahedral distortion. (iii) Screw dislocation-mediated lattice relaxation induces β → γ via cation disordering (Ga 3+ occupancy at β-interstitial sites), forming metastable spinel γ with mixed occupancy across 16d/8a Wyckoff sites. Irradiation-driven β-Ga 2 O 3 →κ/γ/δ transitions, as mechanistically revealed via inelastic thermal spike (i-TS) calculations and molecular dynamics simulations, induce defect-mediated nonlinear photoresponse, critical for optoelectronic engineering.

Han, Xinqing [Shandong Univ., Jinan (China)]↗
DOE OSTI2025

Polypropylene Composites Reinforced With Recycled Waste Cellulosic Fiber/Fine Mixture: The Impact of Cellulose Sieving on Performance

This study explores how a sieving step of waste cellulosic fiber and fine (WCFF) mixture affects the performance of WCFF‐loaded polypropylene (PP) composites and whether the separation of fines from fibers offers an added benefit. The WCFF samples were downsized, and four different filler size ranges were sieved using a series of mesh sizes from 4 to 0.85 mm. The WCFF/PP composites were then compounded at 20 wt.% loading of WCFF using a twin‐screw extruder. Incorporating WCFF increased the tensile strength to 41.28 MPa and the modulus to 3207 MPa, accounting for 28% and 38% enhancements, respectively. Interestingly, the greatest improvements were associated with the nonsieved WCFF case, and the sieved WCFF fibers provided only marginal enhancements over virgin PP. The outperformance of nonsieved WCFF was attributed to the synergistic reinforcement of hybrid fibers and fines as well as the maintenance of longer fibers in the system. However, the strain at break and impact strength of PP decreased after introducing WCFF. Moreover, the complex viscosity and storage modulus increased with an increase in the filler size, due to the formation of a more effective percolative network. The PP's crystallinity exhibited a relatively strong dependency on the sieving, where WCFF samples with short‐aspect‐ratio fillers promoted the crystallinity significantly. It was also found that the WCFF degradation onset temperature increased once it was incorporated into PP. This study suggests that waste cellulosic feedstocks can be utilized as a reinforcement without additional sieving to manufacture high‐performance and cost‐effective composites.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Correlating processing variables to material properties in recycled polypropylene: A data‐driven approach

Abstract Polypropylene (PP) is one of the most widely used plastics, yet its recycling remains limited, with less than 1% of solid waste PP being reprocessed. Mechanical recycling through extrusion is the most practical method, but inconsistent reprocessing conditions introduce variability in material properties. While temperature, screw speed, and residence time influence the thermomechanical stress applied during reprocessing, there are no standardized guidelines for optimizing these parameters. This study examines how these factors shape the properties of recycled PP, using conditions designed to mimic post‐industrial recycled (PIR) scrap. Residence time was measured using colorimetric tracking and correlated with molecular weight, viscosity, and mechanical properties over multiple extrusion cycles. Data‐driven modeling, including response surface methodology, support vector machines, and artificial neural networks, identified processing temperature as the dominant factor in material degradation, followed by residence time. Mechanical properties remained stable, while viscosity decreased predictably with increasing residence time. By linking reprocessing conditions to property evolution, this study provides a method to optimize processing parameters and reduce variability in recycled PP. These findings help manufacturers improve process control, making recycled PP more predictable for reuse in manufacturing. Highlights Study of PIR‐quality PP without additives or compatibilizers. Residence time analysis shows processing temperature drives PP property changes. Mark‐Houwink enables quick molecular weight checks for quality control. Models predict mechanical and rheological shifts in reprocessing. Optimized processing parameters minimize property degradation in recycling.

Estela‐García, John E. [Polymer Engineering Center↗
DOE OSTI2020

Tubulin Double Helix: Lateral and Longitudinal Curvature Changes of Tubulin Protofilament

By virtue of their native structures, tubulin dimers are protein building blocks that are naturally pre-programmed to assemble into cytoskeletal polymers known as microtubules (MTs). Here we demonstrate polycation-directed (i.e. electrostatically tunable) assembly of tubulins through tubulin protofilament conformational changes in the longitudinal and lateral directions, creating novel tubulin double helices and various tubular architectures. Synchrotron small angle X-ray scattering and transmission electron microscopy reveal a remarkable range of nanoscale assembly structures: single- and double-layered double-helix tubulin tubules. The phase transitions from MTs into the new assemblies are dependent on the size and concentration of polycations. Two characteristic scales that determine the number of observed phases are the size of polycation compared to the size of tubulin (≈4 nm) and MT diameter (≈25 nm). This work suggests the feasibility of “programmable breakdown” of protein nanotubes, tearing MTs into double-stranded tubulins and building up previously undiscovered nanostructures, by using polycations with scissor- and glue-like properties. Importantly, we define a new role of tubulins as two-dimensionally shape-controllable building blocks for novel supramolecular architectures. Furthermore, these findings provide insight into the design of protein-based functional materials, for example, as metallization templates for nanoscale electronic devices, kinesin motor-driving molecular screws, and anticancer drug delivery vehicles.

2D shape‐control↗
DOE OSTI2023

Functional group effect of chemically modified microcrystalline methyl cellulose on thermoplastic polyurethane composites

Microcrystalline cellulose (MCC) is a promising bio-based filler for lightweight yet mechanically high-performance eco-polymer composites because of its low density and high biocompatibility. However, intermolecular hydrogen bonding among MCC is stronger than the polymer–filler interactions, which deteriorate the mechanical properties of the composites. Herein, we investigated the effects of functional groups on the mechanical properties of composites by scrutinizing chemically modified microcrystalline methyl cellulose (m-MMC) with three different substitution levels of hydroxyl group to hydroxypropyl (HP) group: no-, low-, and high-level substitution (HP-0, HP-low, and HP-high). The degree of HP substitution of m-MMC was quantitatively measured by CP/MAS NMR analysis. The relatively bulky HP groups interrupted the filler–filler intermolecular interactions and reduced the crystallinity and density of m-MMC, as evident from X-ray diffractometer and pycnometer data, respectively. For scalable production of the composites, the m-MMC were compounded with thermoplastic polyurethane (TPU) by a twin-screw extruder at concentrations between 0.5 and 10 wt%. Despite its low filler concentration, the toughness of m-MMC/TPU composites was remarkably enhanced, up to 28% (229.2 to 294.4 MJ/m 3 ) at 0.5 wt% loading of HP-low, owing to the enhanced polymer–filler interactions. In conclusion, the fundamental understanding on structure–property relationships will provide insights for designing of mechanically robust yet eco-friendly polymer composites.

composites↗
DOE OSTI2024

Melt compounding of spray-dried cellulose nanofibrils/polypropylene and their application in 3D printing

Abstract Micro- and nano-scale cellulosic fillers exhibit excellent dispersion and distribution within a thermoplastic matrix during the process of melt compounding or injection molding. In this study, spray-dried cellulose nanofiber (SDCNF) powders were manufactured using a pilot-scale rotating disk atomizer spray dryer. Bleached Kraft pulp (BKP), unbleached Kraft pulp (UKP), and old corrugated cardboard pulp (OCC) fibrillated at a fines level of 90% were used as feedstock materials for spray-drying. BKP-, UKP-, and OCC- SDCNFs were compounded with polypropylene using a twin screw co-rotating extruder. Maleic anhydride grafted polypropylene (MAPP) was used as a coupling agent in the composite formulations. The tensile, flexural, and impact properties of SDCNF-filled PP composites increased at 10 wt% SDCNF loading. The presence of SDCNFs in the PP matrix resulted in faster crystallization and a 12% reduction in the degree of crystallinity of the neat PP. The coefficient of thermal expansion (CTE) of neat PP was reduced by up to 31% attributable to the presence of the SDCNFs. Application of the SDCNF-reinforced PP composites in 3D printing reduced the shrinkage rate of the printed neat PP by 39%, and the printability of the PP was significantly improved with the addition of the SDCNFs.

Materials Science↗