Search NASA⌕ Search

SEARCH · Search NASA

Results for “Solar Cell”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

Epitaxial Crystal Silicon Absorber Layers and Solar Cells Grown at 1.8 Microns per Minute: Preprint

We have grown device-quality epitaxial silicon thin films at growth rates up to 1.8 ..mu..m/min, using hot-wire chemical vapor deposition from silane at substrate temperatures below 750 degrees C. At these rates, which are more than 30 times faster than those used by the amorphous and nanocrystalline Si industry, capital costs for large-scale solar cell production would be dramatically reduced,even for cell absorber layers up to 10 ?m thick. We achieved high growth rates by optimizing the three key parameters: silane flow, depletion, and filament geometry, based on our model developed earlier. Hydrogen coverage of the filament surface likely limits silane decomposition and growth rate at high system pressures. No considerable deterioration in PV device performance is observed whengrown at high rate, provided that the epitaxial growth is initiated at low rate. A simple mesa device structure (wafer/epi Si/a-Si(i)/a-Si:H(p)/ITO) with a 2.3 um epitaxial silicon absorber layer was grown at 700 nm/min. The finished device had an open-circuit voltage of 0.424 V without hydrogenation treatment.

14 SOLAR ENERGY↗

Indium tin oxide and indium phosphide heterojunction nanowire array solar cells

Heterojunction solar cells were formed with a position-controlled InP nanowire array sputtered with indium tin oxide (ITO). The ITO not only acted as a transparent electrode but also as forming a photovoltaic junction. The devices exhibited an open-circuit voltage of 0.436 V, short-circuit current of 24.8 mA/cm{sup 2}, and fill factor of 0.682, giving a power conversion efficiency of 7.37% under AM1.5 G illumination. The internal quantum efficiency of the device was higher than that of the world-record InP cell in the short wavelength range.

14 SOLAR ENERGY↗

Equivalent circuit analysis of radiative coupling in monolithic tandem solar cells

As solar cell efficiency improves towards the Shockley-Queisser limit, so does the radiative efficiency of the cell. For tandem stacks of cells where energy conversion efficiency now exceeds 46%, radiative coupling between the cells is becoming increasingly important to consider in cell design, measurement, and performance prediction. We show how an equivalent circuit model can capture the complex radiative interactions between cells in such tandem stacks, allowing more insight into the impact on cell performance. The circuit's use is demonstrated by deriving results relevant to the critical step of eliminating coupling effects from measured cell spectral responses.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Interfacial engineering for high performance carbon-based perovskite solar cells

Perovskite solar cells fabricated with carbon-based counter electrodes demonstrate decreased cost, enhanced simplicity and speed of production, and increased stability compared to those produced with standard metallic electrodes. This significant improvement of device stability, cost reduction, and production scalability indicates a promising direction for commercial development and availability of perovskite solar technology. The main limitation of carbon-based perovskite devices is the flawed contact between the carbon electrode and perovskite film which decreases device quality and performance, thereby necessitating treatment of the carbon/perovskite interface. This review provides an overview of the current state of carbon-based perovskite devices, discusses progress in carbon/perovskite interface modification methods, and suggests future directions for the research of carbon electrode/perovskite film interface manipulation.

14 SOLAR ENERGY↗

Mechanically Stacked Four-Junction Concentrator Solar Cells

Multijunction solar cells can be fabricated by bonding together component cells that are grown separately. Because the component cells are each grown lattice-matched to suitable substrates, this technique allows alloys of different lattice constants to be combined without the structural defects introduced when using metamorphic buffers. Here we present results on the fabrication and performance of four-junction mechanical stacks composed of GaInP/GaAs and GaInAsP/GaInAs tandems, grown on GaAs and InP substrates, respectively. The two tandems were bonded together with a low-index, transparent epoxy that acts as an omni-directional reflector to the GaAs bandedge luminescence, while simultaneously transmitting nearly all of the sub-bandgap light. As determined by electroluminescence measurements and optical modeling, the GaAs subcell demonstrates a higher internal radiative limit and thus higher subcell voltage, compared with GaAs subcells without enhanced internal optics; all four subcells exhibit excellent material quality. The device was fabricated with four contact terminals so that each tandem can be operated at its maximum power point, which raises the cumulative efficiency and decreases spectral sensitivity. Efficiencies exceeding 38% at one-sun have been demonstrated. Eliminating the series resistance is the key challenge for the concentrator cells. We will discuss the performance of one-sun and concentrator versions of the device, and compare the results to recently fabricated monolithic four-junction cells.

14 SOLAR ENERGY↗

In situ measurement of power conversion efficiency and molecular ordering during thermal annealing in P3HT:PCBM bulk heterojunction solar cells

Bulk heterojunction organic solar cells hold much promise as commercially viable sources of renewable energy due to their relatively inexpensive fabrication. Developing a fundamental knowledge of how processing conditions influence solar power conversion efficiency will enable rational and efficient design, optimization, and control of new organic solar cell materials. In this report, we use a combination of in situ current–voltage measurements and grazing-incidence wide-angle X-ray scattering experiments at elevated temperature to correlate the changes in photoconversion efficiency to the changes in the molecular ordering of a poly(3-hexylthiophene):[6,6]-phenyl-C₆₁-butyric acid methyl ester (P3HT:PCBM) bulk heterojunction active layer. In situ measurements of current–voltage characteristics were used to optimize the power conversion efficiency and the resulting thermal processing was in agreement with studies from repeated heating and cooling cycles. The improvements in short circuit current with thermal annealing were correlated to an increase in the population of face-on oriented crystallites of P3HT rather than improvements in molecular ordering of PCBM.

14 SOLAR ENERGY↗

Perovskite ink with wide processing window for scalable high-efficiency solar cells

Perovskite solar cells have made tremendous progress using laboratory-scale spin-coating methods in the past few years owing to advances in controls of perovskite film deposition. However, devices made via scalable methods are still lagging behind state-of-the-art spin-coated devices because of the complicated nature of perovskite crystallization from a precursor state. Here we demonstrate a chlorine-containing methylammonium lead iodide precursor formulation along with solvent tuning to enable a wide precursor-processing window (up to ~8 min) and a rapid grain growth rate (as short as ~1 min). Coupled with antisolvent extraction, this precursor ink delivers high-quality perovskite films with large-scale uniformity. The ink can be used by both spin-coating and blade-coating methods with indistinguishable film morphology and device performance. Using a blade-coated absorber, devices with 0.12-cm 2 and 1.2-cm 2 areas yield average efficiencies of 18.55% and 17.33%, respectively. As a result, we further demonstrate a 12.6-cm 2 four-cell module (88% geometric fill factor) with 13.3% stabilized active-area efficiency output.

14 SOLAR ENERGY↗

Effective hole extraction using MoO{sub x}-Al contact in perovskite CH{sub 3}NH{sub 3}PbI{sub 3} solar cells

We report an 11.4%-efficient perovskite CH{sub 3}NH{sub 3}PbI{sub 3} solar cell using low-cost molybdenum oxide/aluminum (i.e., MoO{sub x}/Al) as an alternative top contact to replace noble/precious metals (e.g., Au or Ag) for extracting photogenerated holes. The device performance of perovskite solar cells using a MoO{sub x}/Al top contact is comparable to that of cells using the standard Ag top contact. Analysis of impedance spectroscopy measurements suggests that using 10-nm-thick MoO{sub x} and Al does not affect charge-recombination properties of perovskite solar cells. Using a thicker (20-nm) MoO{sub x} layer leads to a lower cell performance caused mainly by a reduced fill factor. Our results suggest that MoO{sub x}/Al is promising as a low-cost and effective hole-extraction contact for perovskite solar cells.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Nonthermal Site Occupation at the Donor-Acceptor Interface of Organic Solar Cells

Here, we investigate the nature of occupation and relaxation within the charge transfer density of states (CT DOS) for bulk heterojunction organic solar cells consisting of the donor boron subphthalocyanine chloride and the acceptor C 60 . We observe relaxation of geminate CT states on a sub-ns timescale via an approximately 70-meV dynamic redshift in their photoluminescence, whereas free carrier relaxation at longer times leads to the formation of nongeminate CT states at even lower energy. In steady state, we find that thermalization within the DOS is incomplete, resulting in a Boltzmann-like CT state distribution characterized by an effective temperature above that of the ambient. These findings confirm that electron and hole populations can be far from equilibrium in organic solar cells and may prompt a reassessment of analyses that assume the same temperature for their charge-carrier distributions in the dark and under illumination.

14 SOLAR ENERGY↗

π-Extension and chlorination of non-fullerene acceptors enable more readily processable and sustainable high-performance organic solar cells

Organic solar cells (OSCs) processed without halogenated solvents and complex treatments are essential for future commercialization. Herein, we report three novel small molecule acceptors (NFAs) consisting of a Y6-like core but with π-extended naphthalene with progressively more chlorinated end-capping groups and a longer branched chain on the Nitrogen atom. These NFAs exhibit good solubilities in non-chlorinated organic solvents, broad optical absorptions, close π-π stacking distances (3.63–3.84 Å), and high electron mobilities (~10 -3 cm 2 V -1 s -1 ). Further, the o-xylene processed and as-cast binary devices using PM6 as the donor polymer exhibit a PCE increasing upon progressive chlorination of the naphthalene end-capping group from 8.93% for YN to 14.38% for YN-Cl to 15.00% for YN-2Cl. Furthermore similarly processed ternary OSCs were fabricated by employing YN-Cl and YN-2Cl as the third component of PM6:CH1007 blends (PCE = 15.75%). Compared to all binary devices, the ternary PM6:CH1007:YN-Cl (1:1:0.2) and PM6:CH1007:YN-2Cl (1:1:0.2) cells exhibit significantly improved PCEs of 16.49% and 15.88%, respectively, which are among the highest values reported to date for non-halogenated solvent processed OSCs without using any additives and blend post-deposition treatments.

14 SOLAR ENERGY↗

On-device lead absorbing tapes for sustainable perovskite solar cells

Perovskite solar cells are a promising technology that could facilitate and accelerate the energy transition to a sustainable future. However, the toxicity of Pb remains one of the obstacles impeding their commercialization. Here we apply on-device tapes to absorb leaked lead from damaged devices. Furthermore, our chemical approach can capture over 99.9% of leakage without compromising the performance and operation.

14 SOLAR ENERGY↗

Tuning the Intermolecular Electrostatic Interaction toward High-Efficiency and Low-Cost Organic Solar Cells

Organic solar cells (OSCs) have achieved much progress with rapidly increasing power conversion efficiencies (PCEs). It should be noted that the top-performance OSCs are generally consisted of active materials with complex chemical structures, resulting in high costs. Here, combining the material design and morphology control, high-efficiency OSCs are fabricated by a low-cost donor: acceptor blend. A completely non-fused electron acceptor named Tz is designed and synthesized via introducing thiazole units on both sides of a bithiophene core, which shows an outstanding PCE of 13.3% with a typical polythiophene donor. More importantly, optimization guidelines are presented to get excellent morphology for low-cost donor:acceptor systems. Three polythiophenes are selected, poly(3-hexylthiophene) and its two derivatives with electron-withdrawing substitutions (PDCBT and PDCBT-2F), as donors to fabricate the cell devices. The computational and experimental data reveal that decreasing the electrostatic interaction between polythiophene and Tz is the key to getting a suppressed miscibility and thus a high phase purity. Finally, this study provides insight into the molecular design and donor:acceptor matching requirements for high-efficiency and low-cost OSCs.

14 SOLAR ENERGY↗