Search NASA⌕ Search

SEARCH · Search NASA

Results for “Stability and transition”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Mars - Photodesorption from mineral surfaces and its effects on atmospheric stability

Kinetic constraints are employed to identify the reactive chemisorbed complexes, to describe the mechanism of UV-accelerated desorption from Fe (+2) on mineral surfaces, and to estimate the photodesorption rate on Mars. In particular, it is proposed that gases such as O2, CO2, CO, H2O and N2 undergo an adsorption-desorption process at octahedrally coordinated Fe (+2) surface sites to produce seven-coordinate transition-state complexes. The ligand field stabilization energy acquired by these complexes lies between 16 and 18 kcal per mole. Published photocatalysis data are used to assess the role of photodesorption in Martian atmospheric chemistry and stability.

Huguenin, R. L.↗
NASA NTRS2009

Roughness Based Crossflow Transition Control: A Computational Assessment

A combination of parabolized stability equations and secondary instability theory has been applied to a low-speed swept airfoil model with a chord Reynolds number of 7.15 million, with the goals of (i) evaluating this methodology in the context of transition prediction for a known configuration for which roughness based crossflow transition control has been demonstrated under flight conditions and (ii) of analyzing the mechanism of transition delay via the introduction of discrete roughness elements (DRE). Roughness based transition control involves controlled seeding of suitable, subdominant crossflow modes, so as to weaken the growth of naturally occurring, linearly more unstable crossflow modes. Therefore, a synthesis of receptivity, linear and nonlinear growth of stationary crossflow disturbances, and the ensuing development of high frequency secondary instabilities is desirable to understand the experimentally observed transition behavior. With further validation, such higher fidelity prediction methodology could be utilized to assess the potential for crossflow transition control at even higher Reynolds numbers, where experimental data is currently unavailable.

Li, Fei↗
NASA NTRS1990

Design optimization of natural laminar flow fuselages in compressible flow

An optimization method has been developed to design axisymmetric body shapes such as fuselages, nacelles, and external fuel tanks with increased transition Reynolds numbers in subsonic compressible flow. The new design method involves a constraint minimization procedure coupled with analysis of the inviscid and viscous flow regions, and linear stability analysis of the compressible boundary layer. Boundary-layer transition is predicted by a 'hybrid' transition criterion based on Granville's transition criterion and a criterion using linear stability theory coupled with the e(n)-method. A tiptank of a business-jet is used as an example to illustrate that the method can be utilized to design an axisymmetric body shape with extensive natural laminar flow. Boundary layer transition is predicted to occur at a transition Reynolds number of 6.04 x 10 to the 6th on the original tiptank. On the designed body shape, a transition Reynolds number of 7.22 x 10 to the 6th is predicted using compressible linear stability theory coupled with e(n)-method.

Dodbele, Simha S.↗
NASA NTRSDate not supplied

Laminar-Turbulent Transition in High Mach-Number Flows

Accurate prediction of laminar-turbulent transition is critical for the design and characterization of high-speed flight systems. Presently, laminar-turbulent transition prediction in computational fluid dynamics (CFD) is accomplished using PDE-based models coupled to the governing equations of the flow system. Current industrial models suffer significant performance issues when analyzing high-speed systems because they were developed for lower speed flows. Current research focuses on multiple solutions to this problem. The coupling of physics-based stability analysis tools which produce quality transition predictions for high-speed flows to NASA’s OVERFLOW CFD solver is being pursued, as well as the implementation and improvement of emerging models developed specifically for high-speed flow.

High-Speed Flow↗
NASA NTRS1959

Boundary-Layer Transition on Hollow Cylinders in Supersonic Free Flight as Affected by Mach Number and a Screwthread Type of Surface Roughness

The effects of Mach number and surface-roughness variation on boundary-layer transition were studied using fin-stabilized hollow-tube models in free flight. The tests were conducted over the Mach number range from 2.8 to 7 at a nominally constant unit Reynolds number of 3 million per inch, and with heat transfer to the model surface. A screwthread type of distributed two-dimensional roughness was used. Nominal thread heights varied from 100 microinches to 2100 microinches. Transition Reynolds number was found to increase with increasing Mach number at a rate depending simultaneously on Mach number and roughness height. The laminar boundary layer was found to tolerate increasing amounts of roughness as Mach number increased. For a given Mach number an optimum roughness height was found which gave a maximum laminar run greater than was obtained with a smooth surface.

James, Carlton S.↗
NASA NTRS2004

Transition from Ignition to Flame Growth under External Radiation in Three Dimensions (TIGER-3D)

This study focuses on localized ignition by external radiant flux and subsequent flame growth over thin polymeric materials (plastic and paper) in microgravity. Two transition stages were observed. The first transition stage covers the period from the onset of ignition to the formation of stabilized flame near the ignited area. This is followed by the second transition of the flame growth stage from the initial stabilized flame to sustained fire growth away from the ignited area. For the first stage, ignition experiments of thin PMMA sheets were conducted using a CO2 laser as an external source in the 10 s drop tower. The results of front side surface ignition and of backside surface ignition were observed. The effects of imposed flow velocity, sample thickness, and ambient oxygen concentration on ignition are obtained. Numerical study was conducted to investigate to understand and predict ignition behavior observed in the experiments. For the second stage, numerical study is being conducted to describe the effects of gravity on heat release rate of a PMMA sheet. The gravity level was varied from zero to normal gravity. The preliminary results show that the maximum heat release occurs at around 0.02 g.

Kashiwagi, Takashi↗
NASA NTRS2004

Transition from Ignition to Flame Growth under External Radiation in 3D

This study focuses on localized ignition by external radiant flux and subsequent flame growth over thin polymeric materials (plastic and paper) in microgravity. Two transition stages were observed. The first transition stage covers the period from the onset of ignition to the formation of stabilized flame near the ignited area. This is followed by the second transition of the flame growth stage from the initial stabilized flame to sustained fire growth away from the ignited area. For the first stage, ignition experiments of thin PMMA sheets were conducted using a CO2 laser as an external source in the 10 s drop tower. The results of front side surface ignition and of backside surface ignition were observed. The effects of imposed flow velocity, sample thickness, and ambient oxygen concentration on ignition are obtained. Numerical study was conducted to investigate to understand and predict ignition behavior observed in the experiments. For the second stage, numerical study is being conducted to describe the effects of gravity on heat release rate of a PMMA sheet. The gravity level was varied from zero to normal gravity. The preliminary results show that the maximum heat release occurs at around 0.02 g.

Kashiwagi, Takashi↗
NASA NTRS1989

The effect of Mach number on the stability of a plane supersonic wave

The influence of compressibility on the mechanisms governing the various stages of transition in a supersonic wake is investigated. Results from linear stability theory are used to provide physical insights into the observed reduction in growth rate at high Mach numbers. A newly developed hybrid algorithm is used to solve the compressible inviscid linear disturbance equations. Growth rates for both antisymmetric and symmetric modes of two-dimensional and oblique waves are computed for a wide range of Mach numbers. Results from two and three-dimensional direct numerical simulations of a forced compressible time-developing wake are presented in order to understand the nonlinear stages of transition at high Mach numbers. Observed nonlinear growth rate comparisons are made for wakes at two different Mach numbers. The reduction in growth rate at high Mach numbers is explained by examining contour plots of baroclinic torques and the product of dilatation and vorticity.

Chen, Jacqueline H.↗
NASA NTRSDate not supplied

Development of Physics-Based Transition Models for Unstructured-Mesh CFD Codes Using Deep Learning Models

Predicting transition locations over a vehicle surface is of fundamental importance for many engineering applications. With the transition information, the Reynolds-averaged Navier-Stokes (RANS) computations can turn on the turbulence model at the right locations so that drag, lift and other aerodynamic quantities can be accurately predicted. In contrast to the popularity of RANS-based transition modeling in which transition onset is governed by the turbulence equations, physics-based transition models that account for instability waves within the boundary layer, thus more compliant to flow physics, only gained more attention in recent years. This paper describes the development of a new physics-based transition model based on either the linear stability theory (LST) or parabolized stability equations (PSE). The model is designed to communicate with a structured or unstructured-mesh RANS solver back and forth in order to more accurately compute transition fronts over a three-dimensional body. In the developed model, the Python suite of interface codes in conjunction with the LASTRAC software can be executed autonomously to produce transition onset locations for a given laminar or RANS-computed transitional state. In addition, as a proof of concept, the tool set consists of a deep learning neural network model that has been designed and trained to predict instability wave evolutions inside the boundary layer for various instability wave mechanisms across a selected speed range. A machine-learned intelligent profile interpolation model has also been devised to enable reliable instability-wave spectra predictions with just a few points in the mean flow profiles.

Transition Modeling↗
NASA NTRS2012

Stability Analysis for HIFiRE Experiments

The HIFiRE-1 flight experiment provided a valuable database pertaining to boundary layer transition over a 7-degree half-angle, circular cone model from supersonic to hypersonic Mach numbers, and a range of Reynolds numbers and angles of attack. This paper reports selected findings from the ongoing computational analysis of the measured in-flight transition behavior. Transition during the ascent phase at nearly zero degree angle of attack is dominated by second mode instabilities except in the vicinity of the cone meridian where a roughness element was placed midway along the length of the cone. The growth of first mode instabilities is found to be weak at all trajectory points analyzed from the ascent phase. For times less than approximately 18.5 seconds into the flight, the peak amplification ratio for second mode disturbances is sufficiently small because of the lower Mach numbers at earlier times, so that the transition behavior inferred from the measurements is attributed to an unknown physical mechanism, potentially related to step discontinuities in surface height near the locations of a change in the surface material. Based on the time histories of temperature and/or heat flux at transducer locations within the aft portion of the cone, the onset of transition correlated with a linear N-factor, based on parabolized stability equations, of approximately 13.5. Due to the large angles of attack during the re-entry phase, crossflow instability may play a significant role in transition. Computations also indicate the presence of pronounced crossflow separation over a significant portion of the trajectory segment that is relevant to transition analysis. The transition behavior during this re-entry segment of HIFiRE-1 flight shares some common features with the predicted transition front along the elliptic cone shaped HIFiRE-5 flight article, which was designed to provide hypersonic transition data for a fully 3D geometric configuration. To compare and contrast the crossflow dominated transition over the HIFiRE-1 and HIFiRE-5 configurations, this paper also analyzes boundary layer instabilities over a subscale model of the HIFiRE-5 flight configuration that was tested in the Mach 6 quiet tunnel facility at Purdue University.

Li, Fei↗
NASA NTRS2022

Stability Analysis of Streaks Induced by Optimized Vortex Generators

Numerical computations are performed to investigate the potential for transition control in an axisymmetric boundary layer via fully realizable, streamwise stationary streaks induced by an azimuthally periodic array of surface mounted vortex generators (VGs). Previous work has shown that suitable streaks of this type can significantly reduce the growth of Mack’s second mode instabilities, but large streak amplitudes can make the flow susceptible to previously absent streak instabilities that can become the leading cause of transition. Here, we use the adjoint capabilities of the SU2 flow solver to optimize the VG shape to maximize the reduction in the growth of second-mode disturbances while also preventing the streak amplitudes from reaching large enough values to precipitate an earlier onset of transition via streak instabilities. The geometry and the freestream flow conditions are selected to match a relevant trajectory lo-cation from the HIFiRE-1 flight experiment. Results show that the optimized VGs can increase the mean streak amplitude by 117% with respect to a manually developed baseline design. The stability of this optimized basic state is analyzed via the plane-marching parabolized stability equations, predicting a fully laminar flow over the entire cone, or equivalently, yielding transition delay of 130% versus the 17% for the baseline VGs.

Boundary layer transition↗
NASA NTRS2022

Stability Analysis of Streaks Induced By Optimized Vortex Generators

Numerical computations are performed to investigate the potential for transition control in an axisymmetric boundary layer via fully realizable, streamwise stationary streaks induced by an azimuthally periodic array of surface mounted vortex generators (VGs). Previous work has shown that suitable streaks of this type can significantly reduce the growth of Mack’s second mode instabilities, but large streak amplitudes can make the flow susceptible to previously absent streak instabilities that can become the leading cause of transition. Here, we use the adjoint capabilities of the SU2 flow solver to optimize the VG shape to maximize the reduction in the growth of second-mode disturbances while also preventing the streak amplitudes from reaching large enough values to precipitate an earlier onset of transition via streak instabilities. The geometry and the freestream flow conditions are selected to match a relevant trajectory lo-cation from the HIFiRE-1 flight experiment. Results show that the optimized VGs can increase the mean streak amplitude by 117% with respect to a manually developed baseline design. The stability of this optimized basic state is analyzed via the plane-marching parabolized stability equations, predicting a fully laminar flow over the entire cone, or equivalently, yielding transition delay of 130% versus the 17% for the baseline VGs.

Boundary layer transition↗
NASA NTRS1972

A flight evaluation of VTOL jet transport under visual and simulated instrument conditions

A flight investigation was performed with the Dornier DO-31 VTOL to evaluate the performance, handling qualities, and operating characteristics that are considered to be important in the operation of a commerical VTOL transport in the terminal area. The DO-31, a 20,000 kilogram transport, has a mixed jet propulsion system; main engines with nozzles deflect from a cruise to a hover position, and vertical lift engines operated below 170 knots. This VTOL mode incorporates pitch and roll attitude and yaw rate stabilization. The tests concentrated on the transition, approach, and vertical landing. The mixed jet propulsion system provided a large usable performance envelope that enabled simulated IFR approaches to be made on 7 deg and 12 deg glide slopes. In these approaches management of thrust magnitude and direction was a primary problem, and some form of integrating the controls will be necessary. The handling qualities evaluation pointed out the need for additional research of define flight path criteria. The aircraft had satisfactory control and stability in hover out of ground effect. The recirculation effects in vertical landing were large below 15 meters.

Holzhauser, C. A.↗
NASA NTRS1990

Design of laminar flow bodies in compressible flow

An optimization method was developed to design axisymmetric body shapes such as fuselages, nacelles, and external fuel tanks with increased transition Reynolds numbers in subsonic compressible flow. The method involves a constraint minimization procedure coupled with analysis of the inviscid and viscous flow regions, and linear stability analysis of the compressible boundary-layer. Boundary-layer transition is predicted by a 'hybrid' transition criterion based on Granville's transition criterion and a criterion using linear stability theory coupled with the e(sup n)-method. A tiptank of a business jet is used as an example to illustrate that the method can be utilized to design an axisymmetric body shape with extensive natural laminar flow. On the original tiptank boundary layer transition is predicted to occur at a transition Reynolds number of 6.04 x 10 6 on the original tiptank. On the designed body shape a transition Reynolds number of 7.22 x 10 6 is predicted using compressible linear stability theory coupled with e n -method.

Simha S. Dodbele↗
NASA NTRSDate not supplied

Shock-Wave/Boundary-Layer Interaction (SWBLI) Experiments in the Presence of Transition-to-Turbulence on a Flat Plate Model in the NASA LaRC 31-Inch Mach 10 Air Tunnel

Historically, there have been a limited number of studies involving Transitional Shock-Wave/Boundary-Layer Interactions (XSWBLI) in hypersonic flows, the majority of which have been performed at Mach Numbers of 7.5 and below. Additionally, there have been even fewer such experiments which incorporate non-intrusive and optical diagnostics. NASA Langley Research Center (NASA LaRC), in collaboration with The University of Texas at San Antonio (UTSA) and The University of Tennessee Space Institute (UTSI), is currently planning and preparing for a series of experimental aerodynamic tests using the NASA LaRC 31-inch Mach 10 Air Tunnel. The experiments will primarily focus on studying the dynamics of Shock-Wave/Boundary-Layer Interactions (SWBLI) in the presence of transition (XSWBLI) and turbulence (SWTBLI) on a large, flat plate model at a freestream Mach number of 10. Besides continued interest in understanding the flow at high Mach numbers, executing such tests at Mach 10 avoids some known concerns and will aid in solving new problems. XSWBLI are a highly unsteady phenomena and the generation of XSWBLI at lower Mach numbers can prove to be a significant challenge. This concern will be somewhat mitigated in the Mach 10 flow, as boundary layers become increasingly stabilized, but some difficulty in achieving transition is still expected. Modelling SWBLI in the presence of transitional and turbulent boundary layers has also proven to be difficult, so a high-Mach number experiment which applies non-intrusive and optical diagnostics will aid in solving a unique problem as well as advancing the understanding and characterization of an aerodynamic surface at Mach 10.The NASA LaRC 31-inch Wind Tunnel incorporates a test section having a cross-section of 31-inches × 31-inches and provides optical access to the test section via three (3) ultra-violet (UV) transmitting windows on the top, side, and bottom. The Mach 10 operating conditions will consist of pressures (P0) ranging from 2.4 to 10MPa (348 to 1,450 psi) at a temperature (T0) of 1,000 K (1,800 °R). The NASA LaRC 31-inch wind tunnel will deliver 1-minute blow-down runs, of which 30-45 seconds will be consumed to reach the aforementioned test conditions. The pump down time between runs will be approximately 45-60 minutes, which will provide for 6-10 test runs per day over the course of a weeklong entry. The proposed flat plate model will be constructed of stainless steel with geometry consisting of a10-inch × 30-inch upper surface and a 2-inch thickness. The model will be designed to support multiple leading-edge inserts in order to examine blunt, round, and sharp leading edges at Mach 10. Adjustments will be made to manage boundary layer thickness as well as the strength and size of the shock interaction region for each test. Measurements and diagnostics will be performed though high-speed Schlieren, on-body high-speed pressure transducers, IR thermography, and oil flow visualization. Hypersonic vehicle applications have and will continue to emerge at the forefront of aerospace. The NASA-UTSA-UTSI team realizes the value of characterizing SWBLI, XSWBLI, and SWTBLI behaviors well beyond single-digit hypersonic Mach numbers. As hypersonic vehicle speed capabilities continue to increase, measurement and diagnostic methods for Mach numbers of 10 and beyond will provide the foundation for a firm understanding of flow field behavior which will directly influence the advancement of technologies towards the design and manufacturing of high-speed aerodynamic surfaces, controls, thermal protection systems, acoustic treatments, and structural components. The use of non-intrusive and optical diagnostic methods in such experimentation is pivotal in developing the visualization and empirical data necessary to advance the aforementioned technology areas.

Shockwave/Boundary-Layer Interactions↗
NASA NTRS1994

Aromatic Polyimides Containing Meta-Biphenoxy Moieties

Synthesis of two novel monomers and subsequent incorporation into aromatic polyimides yields polyimides containing meta-biphenoxy moieties exhibiting stability at high temperatures and having glass-transition temperatures lower than state-of-the-art polyimides containing para-biphenoxy moieties. Because of outstanding thermal stability, low density, resistance to radiation, electrical-insulating capability, toughness, and flexibility, linear aromatic polyimides used increasingly for applications in aerospace and electronics industries and possibly in others.

St. Clair, Terry L.↗