Search NASA⌕ Search

SEARCH · Search NASA

Results for “Steel manufacturing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Heat Transfer Characteristics of Particle and Air Flow Through Additively Manufactured Lattice Frame Material Based on Octet-Shape Topology

Particle-to-supercritical carbon dioxide (sCO 2 ) heat exchanger is a critical component in next-generation concentrating solar power (CSP) plants. The inherently low heat transfer between falling particles and sCO 2 imposes a challenge toward economic justification of levelized cost of electricity produced through solar energy. Introduction of integrated porous media with the walls bounding particle flow has the potential to enhance the overall particle-to-sCO 2 heat exchanger performance. Here, this paper presents an experimental study on heat transfer characterization of additively manufactured lattice frame material based on Octet-shaped unit cell with particles and air as working fluids. The lattice structures were additively manufactured in stainless steel (SS) 316L and SS420 (with 40% bronze infiltration) via Binder jetting process, where the lattice porosities were varied between 0.75 and 0.9. The mean particle diameters were varied from 266 μm to 966 μm. The effective thermal conductivity and averaged heat transfer coefficient were determined through steady-state experiments. It was found that the presence of lattice enhances the effective thermal conductivity by 2–4 times when compared to packed bed of particles alone. Furthermore, for gravity-assisted particle flow through lattice panel, significantly high convective heat transfer coefficients ranging from 200 W/m2K to 400 W/m2K were obtained for the range of particle diameters tested. The superior thermal transport properties of Octet-shape-based lattice frame for particle flow makes it a very promising candidate for particle-to-sCO 2 heat exchanger for CSP application.

14 SOLAR ENERGY↗
DOE OSTI2022

Conceptual Design of the Transformational Challenge Reactor

The Transformational Challenge Reactor is a 3-MW(thermal) helium-cooled experimental nuclear reactor designed using an additive manufacturing–informed agile design process. This design process leverages rapid prototyping and advanced materials from emerging additive manufacturing technologies, key characteristics that enable rapid design maturation. The resulting core design incorporates a blend of advanced reactor technologies into an intermediate-spectrum microreactor, including conventionally manufactured tristructural isotropic (TRISO) fuel particles in an advanced manufactured SiC fuel element and a solid yttrium hydride moderator encapsulated in steel. Matured during the design effort, these technologies are incorporated with additively manufactured steel support and fluidic structures to form a 75-cm-outer-diameter cylindrical active core region. Below and above the active core region are axial SiC reflectors, which are housed inside the reactor pressure vessel. The reactor is controlled with an annular shroud actuated external to the pressure vessel in the gap between the pressure vessel and a steel radial reflector. A safety rod is at the center of the core to shut down the reactor when necessary. Helium pressurized at 5 MPa is forced into the pressure vessel below the core and around the core to the top plenum before it is forced down through the axial reflectors and the active core region. The primary pressurized helium loop is operated up to 500°C and includes the pressure vessel, the circulator, and the hot side of a helium-to-air heat exchanger. The secondary loop rejects all heat from the primary loop to ambient air through a heat exchanger. A vented temporary confinement building contains the entire primary loop, with penetrations for a stack, cooling, and the secondary ambient air loop. Finally, this is the first advanced nuclear microreactor designed using additive manufacturing technologies, demonstrating their applicability in an accelerated advanced design process.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2024

Neutron Irradiation Experiments

This presentation discusses the ongoing and upcoming neutron irradiation experiments within the Advanced Materials and Manufacturing Technologies (AMMT) program for the 2024 AMMT program review meeting. Ongoing and upcoming neutron irradiation of additively manufactured 316 stainless steel and A709 in the High Flux Isotope Reactor and Advanced Test Reactor are described.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Feature Based Qualification (FBQ) of Wire Arc Additively Manufactured (WAAM) 17-4PH Martensitic Stainless Steels

The Department of Defense (DOD) programs of records desire to reduce the time and cost of the development and delivery loop in metal additive manufacturing (AM), including establishing forwarded AM capabilities. The success of these efforts relies on a robust and qualified process. To achieve this, the United States Army Combat Capabilities Development Command Ground Vehicle Systems Center Materials Engineering (GVME) needs to be able to quickly evaluate, test, and develop feedstocks, processes, and parts. This report is directed towards demonstrating the need for a framework for metal AM processes, defining and exploring geometries for metal AM process qualification, testing resultant deposition, and delivering actionable data.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Additive manufacturing process parameter determination for a new Fe-C-Cu alloy

As a potential replacement for stainless steel alloys commonly used to print parts with laser powder bed fusion, a new Cu precipitation strengthened ferrous alloy, with composition Fe-0.2C-6Cu (wt%), was recently developed. This material is Co- and Ni-free, printable, has mechanical properties comparable to that of high strength stainless steels (approximately 1300 MPa UTS), and is cost-advantaged relative to existing low-alloy steels for additive manufacturing of parts with complex shapes. To gain traction for broader application, optimal laser powder bed fusion (LPBF) processing conditions to produce nearly defect-free parts without compromising mechanical strength are needed. Here, an optimal processing window based upon laser speeds that achieve minimal porosity was quantified via comparisons of measured melt pool penetration, scan speeds, printed material density and laser beam energy density on a commercial LPBF unit operating at 350 W, 80 μm hatch spacing, and 50 μm layer thickness based upon optimal parameters for 17-4PH. Furthermore, the window is 300 to 500 mm/s to achieve >99.8 % dense Fe-0.2C-6Cu (wt%) specimens. Other defects such as burning, spatter, and lack of fusion were also avoided in this window. The window was validated with in-situ synchrotron X-ray imaging that enabled visualization of the vapor cavity, melting, and solidification during a single laser track scan on a miniature powder bed sample. In addition, in-situ infrared imaging provided temperature fields, cooling rate and solidification range, and confirmed minimal printing defects and spatter within the processing window.

36 MATERIALS SCIENCE↗
DOE OSTI2021

In Situ High Energy X-ray Diffraction Characterization of Phase Transformations and Mechanical Behaviors in Rapidly Solidified Titanium and Stainless Steel Alloys [Thesis]

Advanced manufacturing techniques like additive manufacturing (AM) have poised themselves to revolutionize metal manufacturing. A wide range of AM techniques are capable of manufacturing metal components with unique, complex geometries and hastening the scientific-engineering-development cycle. Metal AM relies on a layer-by-layer rapid manufacturing process to build components from the substrate up. Rapid solidification is a large departure from traditional metal manufacturing due to its complex physics. Characterization of rapid solidification is difficult, stemming from the small volumes used in AM and the fast dynamics of the process. High energy X-ray diffraction (HEXRD) is a solution to the characterization problems of rapidly solidified alloys and AM. HEXRD can probe small volumes at fast rates and provides a wide range of thermomechanical and kinetic information. This thesis presents the application of HEXRD to rapidly solidified titanium and stainless steel alloys through a series of case studies. In the first two studies, HEXRD is applied to rapidly solidified titanium and stainless steel welds. The materials are characterized for their temperature history, phase changes, kinetics, and microstructural evolution. In the next case study, HEXRD is applied to characterize phase changes in elastocaloric NiTi shape memory alloys (SMAs) under thermomechanical load. HEXRD, in conjunction with other tools, is used to explain the superior performance of the additively manufactured SMAs. In the final two case studies, HEXRD is used to measure the mechanical response of AM parts with complex geometries; namely, the octet truss lattice. Diffraction reveals a wide range of materials information about the AM microstructure including unexpected phases, texture, and mechanical response to loading. The mechanical results from HEXRD and then compared with theoretical predictions about the performance of octet truss lattices. Summarily, HEXRD is a diverse tool that is poised to address the complex characterization problems of many aspects of the additive manufacturing process.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Material properties and mechanical behaviour of functionally graded steel produced by wire-arc additive manufacturing

Metal Big Area Additive Manufacturing is an additive manufacturing technique based on Gas Metal Arc Welding (GMAW) with the option to use many shielding gases, and materials. The system is equipped with a dual torch design allowing for printing different materials; in our study, AISI 410 stainless steel and AWS ER70S-6 mild steel are both printed in the same component. Different print strategies were designed to highlight changes in material and mechanical properties. Deformation behaviour of a materials’ interface was analysed by two-dimensional digital image correlation of uniaxial tensile specimens in displacement-controlled tests. Instances of non-homogeneous local strains adjacent to the interface are observed, as well as variability in mechanical behaviour and microstructure based on location within the print. Optical and electron microscopy are used to evaluate three microstructural zones in a 5 mm range of the interface between mild steel and stainless steel. Areas far from the interface produced polygonal ferrite and pearlite, while areas close to the interface produced acicular ferrite and bainite. Chromium redistribution profiles are dependent on the print strategy used, as shown by scanning electron microscopy with Energy dispersive spectroscopy. Evidence produced via electron backscatter diffraction is shown to support the argument that transformation induced plasticity is not the cause for the non-homogeneous deformation.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Data for: Ultrasonic characterization of material heterogeneities in stainless steel parts fabricated by powder bed fusion

These are the raw ultrasonic waveform files and nanoindentation measurements for three additively manufactured 316L stainless steel components with different fabrication parameters. Each part's length is divided into four segmented regions where their fabrication energy densities change. Part V+ begins at 33 J/mm^3 and increases in energy density by 3 J/mm^3 with each segment. Part C remains at a constant 33 J/mm^3 throughout the part. Part V- begins at 33 J/mm^3 and decreases in energy density by 3 J/mm^3 with each segment. We have found that the ultrasonic waves in regions with higher energy densities will traverse more quickly, as shown by the shorter time of flight, and vice versa. Similarly, nanoindentation measurements of reduced modulus and hardness follow this trend. We have measured the direction in which the parts were fabricated (build direction) and the segmented regions that are perpendicular to the build direction (transverse directions). The build direction longitudinal wave velocity measurements are considerably lower than their transverse direction counterparts, indicating anisotropy between the two directions. In Part C, we have removed material from one of its surfaces and recorded its ultrasonic and nanoindentation measurements with each material removal iteration. Changes in the material properties are more prominent by nanoindentation, suggesting material heterogeneity between the part's surface and interior. The README.txt file has information on how to navigate the files and process the data.

Anisotropy↗
DOE OSTI2021

Role of scan strategies and heat treatment on grain structure evolution in Fe-Si soft magnetic alloys made by laser-powder bed fusion

A major goal in printing soft magnetic Fe-Si steels using additive manufacturing is to take advantage of the potential for complex geometric designs and site-specific grain control. One major step in the processing of these alloys is understanding how processing parameters might impact how the as-built microstructure responds to annealing (i.e. the annealing response). The impact of scan strategy on the annealing response for thin wall geometries is specifically explored. Two scan strategies were explored for a thin wall geometry that produced a strongly columnar grain structure and equiaxed grain structure. Additionally, samples from both scan strategies annealed at 1200 °C showed a marked difference in annealing response with the more equiaxed sample seeing full recrystallization and grain growth, while the more columnar grain structure saw little change in microstructure. After analysis through characterization techniques and thermal-mechanical simulations Differences in internal energy within the grains were ruled out because calculated GND density values were similar for both samples. The formation of secondary particles was ruled out as a contributing factor due to the type of oxide formations and their size. It was concluded that the contributing factor to the difference in the annealing response were a difference in the resulting grain size and the density of high angle grain boundaries. These two differences were largely attributed to differences in the thermal gradient conditions due to grains preferentially growing in the direction of the steepest thermal gradient.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Detection of Part Porosity in Additive Manufacturing Using Machining

Monitoring of part porosity in additive manufacturing is critical for part qualification and process parameter development. This article describes the monitoring of porosity in additive manufacturing using machining. Grade 91 steel samples with different levels of porosity were additively manufactured using a laser blown-powder process. The samples were machined, and the tool position and cutting power were monitored using the machine controller and an external power transducer, respectively. Results show that the power transducer is sensitive to machining porosities. A novel approach using the standard deviation of cutting power was developed to determine the location of porosities along the length of the machining pass. Test cuts were completed at different machining process parameters. Results showed that the probability of detection was one for pore volume greater than 0.3 mm 3 at different machining parameters. In conclusion, although the detection of porosity using machining is a destructive method for evaluation, it offers a low-cost and fast approach for monitoring porosity in additive manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Multi-material additive manufacturing of aluminum 6061-T6 alloy with stainless steel 304: Suppression of intermetallic compounds and interface growth mechanism

Fabricating integrated aluminum-steel structures is difficult because of metallurgical incompatibilities that promote intermetallic compound (IMC) formation at their interfaces. This work introduces a practical route for additively manufacturing 6061-T6 aluminum alloy (AA6061-T6) directly onto 304 stainless steel (SS304) using a high shear strain rate-assisted interfacial bonding mechanism. Through the friction extrusion deposition-based additive manufacturing method, both single- and multi-layer deposits of AA6061-T6 were successfully fabricated on SS304, yielding a robust hybrid multi-material structure. Comprehensive analyses of deposition quality, interface porosity, and bonding performance showed that the interface achieved a tensile strength exceeding 154 MPa under quasi-static loading. Microstructural observations revealed that the deposited aluminum layers experienced severe plastic deformation, resulting in pronounced grain refinement. Importantly, the interfacial zone was found to be free of brittle IMCs, instead containing a thin amorphous layer that evolved through a non-linear reaction-zone growth law. This solid-state additive strategy establishes a promising pathway for lightweight structural systems, nuclear energy component cladding, and multifunctional engineering components, redefining how dissimilar metals can be integrated for advanced applications.

Aluminum alloy↗
DOE OSTI2024

Microstructure Optimization and Novel Processing Development of ODS Steels for Fusion Environments (Final ARPA-E Report)

This project aimed to develop scalable, cost-effective fabrication of high-performance, oxide- dispersion-strengthened (ODS) steel using advanced manufacturing methods (AMMs) for fusion blanket-breeding applications. Gas atomization reaction synthesis (GARS) enables the synthesis of precursor ODS steel powders without prolonged mechanical alloying. This process creates a chromium (Cr)-enriched surface oxide with yttrium/titanium (Y/Ti)-enriched intermetallics in powder interiors. GARS powders were consolidated to >99% of the theoretical density using a first-of-a-kind shear assisted processing and extrusion (ShAPE) and laser-based powder bed fusion (L-PBF) AM processes. These processes led to ODS steels containing a high-density of nano-oxide dispersoids that enhance high-temperature mechanical properties. Such scalable, cost-effective fabrication of ODS steels can enable efficient power conversion cycles (=40%) at operating temperatures beyond 900 K in future fusion power plants.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Ultrasonic characterization of material heterogeneities in stainless steel components produced by laser powder bed fusion

We introduce pulse-echo ultrasound as a method for characterizing the impact of powder bed fusion parameters on the properties of additively manufactured stainless-steel components, their material anisotropy, and location-dependent heterogeneity. Our results indicate that accurate characterization requires careful selection of ultrasonic propagation paths, which must consider the direction of additive layering, variations in processing parameters, and the component's geometry. We employed two distinct methods to estimate material properties from ultrasonic data: One assumes isotropy, while the other accounts for anisotropic interactions during the propagation of elastic waves. When applied to samples fabricated with laser energy densities ranging from 24 to 42 J/mm³ , these methods revealed transverse isotropy and weak anisotropy (quantified by small Thomsen parameters, ε = 0.0651 and γ = 0.0092) and less than a ∼6 % change in acoustic impedance. The assumption of isotropy, in this case, leads to small errors (less than 4 % or 1 % for Young's modulus in the build or transverse directions) when estimating orthotropic material properties using ultrasonic data measured along just two orthogonal directions, one of which must align with the build direction. By comparing ultrasonic measurements — which aggregate the spatial variability in material properties along the length of elastic wave propagation into a single value — with localized measurements obtained from surface nanoindentation, we uncovered and spatially profiled significant differences between the surface and interior properties. Specifically, the surface Young's modulus decreased from approximately 210 GPa to 180 GPa within a depth of about 3 mm. We attribute this surface-localized heterogeneity in PBF-fabricated components to distinct thermal histories experienced by the surface and interior regions. Collectively, the results of this study establish a framework for the ultrasonic characterization of material heterogeneity and anisotropy in material properties and demonstrate its application in additively manufactured metal components.

36 MATERIALS SCIENCE↗
DOE OSTI2022

TEM Specimen Manufacturing to Support Analysis of IASCC Mechanisms in Irradiated Austenitic Steels – Light-Water– Relevant Materials

The present report describes the manufacturing of samples for advanced microstructure studies of mechanisms of irradiation-assisted stress corrosion cracking (IASCC) in the materials of light-water reactor (LWR) internal components. The samples were manufactured via FIB (focused ion beam milling) from 4-point-bend specimens subjected to oxidation and mechanical loading in a simulated LWR environment (primary water, PW). The corrosion tests were conducted at the University of Michigan (UM), and the tested specimens were transported to ORNL to perform FIB work. Finally, the manufactured FIB specimens were shipped back to the UM for microstructure characterization. Section 1 in the report provides a brief introduction; Section 2 describes materials, their in-service and irradiation history, and the geometry of specimens for IASCC testing. Section 3 documents typical work steps (specimen mapping) and reports the number of manufactured FIB objects. Section 4 briefly describes the preliminary results of microstructure analysis performed at the University of Michigan and highlights the key findings. The summary and conclusions section discusses future possible future steps and generalizes the obtained results, their unique character, and their importance for the nuclear industry.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗