Search NASA⌕ Search

SEARCH · Search NASA

Results for “Struts”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Development of an adhesively bonded beryllium propulsion structure for the Mariner Mars 1971 spacecraft

The design, testing, and fabrication of the support truss structure for the propulsion system of the Mariner 9 spacecraft are described. Support is provided by an 8.9-kg (19.5-lbm) truss assembly consisting of beryllium tubes adhesively bonded to magnesium end fittings. Beryllium was selected for the tubular struts in the truss because of its exceptionally high stiffness-to-weight ratio. Adhesive bonding, rather than riveting, was utilized to join the struts to the end fittings because of the low toughness (high notch sensitivity) of beryllium. Magnesium, used in the end fittings, resulted in a 50% weight saving over aluminum since geometric factors in the fitting design resulted in low stress areas where magnesium's lower density is a benefit.

Stevens, J. H.↗
NASA NTRS1972

Solar wind rare gas analysis: Trapped solar wind helium and neon in Surveyor 3 material

The He-4 and Ne-20 contents in sections of the Surveyor 3 support strut samples were determined by optical and scanning electron microscopy and are compared to the results of the Apollo solar wind composition (SWC) experiments. The He-4/Ne-20 ratio in the samples from the sunlit side of the strut was approximately 300; the ratios determined in Apollo 12 lunar fines and SWC foil were below 100. The He-4/He-3 ratios were also determined, and the ratio obtained from Surveyor 3 material is higher than those found with Apollo 11 and 12 SWC experiments. The effects of spallation by cosmic rays or solar protons, stripping by cosmic ray or energetic solar alpha particles, recycling of solar wind He and radiogenic Ne, He from terrestrial atmosphere, mass discrimination near the moon, mass dependence of trapping probability, diffusion, and contamination by lunar dust are considered.

Buehler, F.↗
NASA NTRS1973

Collapsible structure for an antenna reflector

A collapsible support for an antenna reflector for use in supporting spacecraft antennas is described. The support has a regid base and a number of struts which are pivoted at the base. The deployment of the struts and their final configuration for supporting the antenna are illustrated.

Trubert, M. R.↗
NASA NTRS1975

Expandable space frames

Frame consists of struts connected by hinge joint assemblies. Because struts are hinged, entire frame can be collapsed during transportation and expanded at construction site. Frame has two types of hinge joint assemblies; one for three-dimensional space frame expansion and another for two-dimensional expansion.

Schoen, A. H.↗
NASA NTRS1973

Cruise Drag Results from High Speed Wind Tunnel Tests of NASA Refan JT8D Engine Nacelles on the Boeing 727-200

High speed wind tunnel test results are presented showing the cruise drag effect of installing JT8D-109 Refan engines on a Boeing 727-200. Incremental drags of a refan center inlet and side nacelles are presented for several configuration variations. Static pressure distributions were obtained on the side nacelle strut and on the fuselage (above and below the strut). Oil flow photographs of selected configurations are also presented. In general the drag level of the refan installation is slightly better than predicted prior to the test and the drag rise is favorable.

Easterbrook, W. G.↗
NASA NTRS1974

Experimental investigation of the landing dynamics of three-legged spacecraft models

An experimental investigation was conducted to obtain accurate data from two three-legged spacecraft landing systems for purposes of validating current and future computer programs for legged landers. Two landing-gear systems were investigated: an inverted tripod system and a cantilever system. Tests were conducted for eight landing conditions chosen to obtain stability data, maximum loads, and maximum strokes for correlation with analytical results. Data from the two models are not directly comparable because of geometry and mass differences, but both are considered to be typical models of the respective landing-gear systems. Results indicate that maximum accelerations for both models, which occurred during a nearly flat landing on a horizontal surface, were nearly the same (approximately minus 18g). Maximum primary strut forces occurred for landings into a 20 deg slope and were 40 kiloNewtons (9000 lbf) and 47 kiloNewtons (10 500 lbf) for the inverted tripod and cantilever models, respectively; and maximum primary strut strokes for both models were 19 cm (7.4 in.). The inverted tripod model was slightly more stable than the cantilever model because of a larger ratio of footpad radius to center-of-gravity height.

Stubbs, S. M.↗
NASA NTRS1974

Boron/aluminum for space applications

Several experimental boron/aluminum structures have been built for aircraft and space vehicle applications. The success of these structures has led to the decision to use boron/aluminum tubular struts on the mid-fuselage section of the Space Shuttle Orbiter. The suitability of boron/aluminum for this application has been demonstrated in a program that involved fabricating 100 tubes and performing static, fatigue, corrosion, thermal/mechanical fatigue, and damage tolerance tests on them. Other potential applications for boron/aluminum on the Space Shuttle include the wing carry-through panels and side panels for the mid-fuselage, and the landing gear struts. These applications result in significant weight savings over conventional non-composite designs at moderate costs. Boron/aluminum can now be considered a production material that, in many cases, is competitive on a weight and/or cost basis with an all-metal or resin composite system.

Robertson, A. R.↗
NASA NTRS1976

Test-section noise of the Ames 7 by 10-foot wind tunnel no. 1

An investigation was made of the test-section noise levels at various wind speeds in the Ames 7- by 10-Foot Wind Tunnel No. 1. No model was in the test section. Results showed that aerodynamic noise from various struts used to monitor flow conditions in the test section dominated the wind-tunnel background noise over much of the frequency spectrum. A tapered microphone stand with a thin trailing edge generated less noise than did a constant-chord strut with a blunt trailing edge. Noise from small holes in the test-section walls was insignificant.

Soderman, P. T.↗
NASA NTRS1976

Evaluation of scramjet combustor performance using cold nonreactive mixing tests

Results of cold supersonic ducted mixing tests are presented and compared with results of hot mixing and combustion tests obtained using the same apparatus. Two strut injectors are evaluated, one with injectors parallel to the free-stream direction and one with perpendicular injectors. Detailed flow surveys are used to determine the degree of mixing accomplished in the cold flow tests. In the hot flow tests, the amount of mixing and reaction is inferred from survey data and comparison of wall static pressures with one-dimensional flow calculations. These comparisons show that cold mixing results can be used to predict combustion results. In some cases, such as the normal injection strut tested, cold mixing efficiency and combustion efficiency are identical. In other cases, transport models developed from cold flow results can be applied to predict the effects of higher temperature mixing and reaction. Cold flow surveys are also used to determine detailed flow characteristics not readily measured in hot flows.

Mcclinton, C. R.↗
NASA NTRS1976

Results of a landing gear loads test using a 0.0405-scale model (16-0) of the space shuttle orbiter in the Rockwell International NAAL wind tunnel (OA163), volume 1

Experimental aerodynamic investigations were conducted on a sting mounted scale representation of the 140C outer mold line space shuttle orbiter configuration in the low speed wind tunnel. The primary test objectives were to define the orbiter landing gear system pressure loading and to record landing gear door and strut hingemoment levels. Secondary objectives included recording the aerodynamic influence of various landing gear configurations on orbiter force data as well as investigating 40 x 80 ft. Ames Wind Tunnel strut simulation effects on both orbiter landing gear loads and aerodynamic characteristics. Testing was conducted at a Mach number of 0.17, free stream dynamic pressure of 42.5 PSF, and Reynolds number per unit length of 1.2 million per foot. Angle of attack variation was 0 to 20 while yaw angles ranged from -10 to 10 deg.

Mennell, R. C.↗
NASA NTRS1978

Analysis of a suspension system for a wheel rolling on a flat track

A flexure strut wheel suspension system is described which keeps a wheel flat against the track and maintains a small interface moment. Equations are presented for the evaluation of this moment. A comparison of the flexure strut system is made with a rigid link design containing pivot bearings.

Mcginness, H.↗
NASA NTRS1979

Economical processing of fiber-reinforced components with thermal expansion molding

The concept of economical fabrication of fiber-reinforced structural components is illustrated with an example of a typical control surface (aileron). The concept provides for fabricating struts, ribs, and a cover plate as an integral structure in a hardening device and then joining the closure cover plate mechanically. Fabrication of the integral structure is achieved by the 'thermal expansion molding' technique. The hardening pressure is produced by silicone rubber cores which expand under the influence of temperature. Test results are presented for several rubber materials as well as for various structural pieces. The technique is demonstrated extensively for an aileron, consisting of five ribs, struts, and a cover plate. Economically, for a large scale technical production of an aileron, cost savings of twenty-five percent can be realized compared to those for a sheet metal structure.

Schneider, K.↗
NASA NTRS1980

Exploratory investigation of the effects of vortex bursting on the high angle-of-attack lateral-directional stability characteristics of highly-swept wings

A recent low-speed wind-tunnel investigation of highly-swept wings has shown that vortex breakdown at high angles of attack can cause large destabilizing effects on static lateral-directional stability characteristics, and that the destabilizing effects of vortex breakdown can be greatly aggravated by model support strut interference effects. The present paper discusses these effects based on the results of static force tests of several highly-swept wing configurations for different wind-tunnel strut setup arrangements. Also included in the paper are photographs obtained during tuft-, smoke-, and helium-bubble flow visualization studies to indicate wing flow behavior patterns

Johnson, J. L., Jr.↗
NASA NTRS1980

Deployable and erectable concepts for large spacecraft

Computerized structural sizing techniques were used to determine structural proportions of minimum mass tetrahedral truss platforms designed for low Earth and geosynchronous orbit. Optimum (minimum mass) deployable and erectable, hexagonal shaped spacecraft are sized to satisfy multiple design requirements and constraints. Strut dimensions characterizing minimum mass designs are found to be significantly more slender than those conventionally used for structural applications. Comparison studies show that mass characteristics of deployable and erectable platforms are approximately equal and that the shuttle flights required by deployable trusses become excessive above certain critical stiffness values. Recent investigations of eractable strut assembly are reviewed. Initial erectable structure assembly experiments show that a pair of astronauts can achieve EVA assembly times of 2-5 min/strut and studies indicate that an automated assembler can achieve times of less than 1 min/strut for around the clock operation.

Bush, H. G.↗
NASA NTRS1981

Numerical analysis of the scramjet inlet flow field using two-dimensional Navier-Stokes equations

A computer code has been developed to solve the full two-dimensional Navier-Stokes equations in a scramjet inlet. The analysis uses a numerical coordinate transformation which generates a set of boundary fitted curvilinear coordinates. The explicit finite-difference algorithm of MacCormack is used to solve the governing equations. A two-layer eddy viscosity model is used for the turbulent flow. The code can analyze both inviscid and viscous flows with multiple struts in the flow field. Detailed results are presented for two model problems and two scramjet inlets with one and two struts. The application of the two-dimensional analysis in the preliminary design of the actual scramjet inlet is briefly discussed.

Kumar, A.↗
NASA NTRS1982

Sequential deployment of truss structures

The geometry investigated most intensively was the triangular tetrahedral truss. A square type truss having the same topology was also investigated. The tetrahedral truss is composed of surface struts and core members. In the deployable form, the entire truss is viewed as being made up of a number of parallel truss ribs connected to each other by interrib struts and members. The packaging efficiency of the truss was evaluated.

Hedgebeth, J. M.↗
NASA NTRS1981

Suspension system for a wheel rolling on a flat track

An improved suspension system for an uncrowned wheel rolling on a flat track is presented. It is characterized by a wheel frame assembly including a wheel frame and at least one uncrowned wheel connected in supporting relation with the frame. It is adapted to be seated in rolling engagement with a flat track, a load supporting bed, and a plurality of flexural struts interconnecting the bed in supported relation with the frame. Each of said struts is disposed in a plane passing through the center of the uncrowned wheel surface along a line substantially bisecting the line of contact established between the wheel surface and the flat surface of the truck and characterized by a modulus of elasticity sufficient for maintaining the axis of rotation for the wheel in substantial parallelism with the line of contact established between the surfaces of the wheel and track.

Mcginness, H. D.↗
NASA NTRS1982

Analysis of the Scramjet inlet flow field using two-dimensional Navier-Stokes equations

A computer code was developed to solve the full two dimensional Navier-Stokes equations in a scramjet inlet. The analysis uses a numerical coordinate transformation which generates a set of boundary-fitted curvilinear coordinates. The explicit finite difference algorithm of MacCormack is used to solve the governing equations. A two-layer eddy viscosity model is used for the turbulent flow. The code can analyze both inviscid and viscous flows with multiple struts in the flow field. Detailed results are presented for two model problems and two scramjet inlets with one and two struts. The application of the two dimensional analysis in the preliminary design of the actual scramjet inlet is briefly discussed.

Kumar, A.↗