Search NASA⌕ Search

SEARCH · Search NASA

Results for “TELLURIDE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Robust passivation of CdSeTe based solar cells using reactively sputtered magnesium zinc oxide

Magnesium zinc oxide (MZO, Mg x Zn 1-x O) is a leading emitter for CdTe-based solar cells due to its transparency and the ability to tune its conduction band offset with the absorber. Devices employing alloyed cadmium selenide telluride (CST, CdSe y Te 1-y ) absorbers achieved high efficiency (>19%) using MZO deposited by reactive sputtering over a broad composition range (3.68–3.92 eV, x: 0.20–0.35). Minimal differences in implied and measured open circuit voltage indicate that the contacts are well passivated and highly selective across the spectrum of MZO employed. Device performance insensitivity to MZO composition, which is not observed in CdTe devices, is attributed to the formation of an oxygenated interface layer. Se volatility creates a group VI deficiency at the interface that drives O migration from the MZO into the absorber. This introduces conductivity in the emitter not present in its as-deposited state, contributing to the exceptional performance observed. It is shown that the quality of device passivation depends on the oxidation state of the as-deposited MZO such that intelligent control and management of the reactive sputtering process is required.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Sputter-deposited CdMgTe for rear contact to CdSeTe/CdTe solar cells

CdTe-based photovoltaic device performance improvement is predominantly limited by open-circuit voltage. This work approaches the voltage deficit challenge through the incorporation of a cadmium magnesium telluride (CdMgTe) electron reflector layer at the back of 1.5- μm CdSeTe/CdTe absorbers to reduce back-surface recombination through a conduction band offset. A sputtered CdMgTe electron reflector layer permitted low fabrication temperatures and circumvented the intolerance of CdMgTe to thermal processing present in traditional close-space sublimation (CSS)-deposited CdMgTe devices. Here, we demonstrate that sputtered CdMgTe simultaneously promotes the retention of chlorine passivation and magnesium which is not feasible with CSS fabrication. We also show the importance of the Cu and Te back contact order in CdMgTe devices. Through the optimization of the sputtered CdMgTe substrate temperature, doping, and back structure configuration, 1.5 μm CdSeTe/CdTe devices with a sputtered CdMgTe layer achieved an efficiency of 16.0%, significantly higher than with CSS CdMgTe, and demonstrated partial enactment of electron-reflector behavior.

14 SOLAR ENERGY↗
DOE OSTI2022

Technoeconomic Analysis of High-Value, Crystalline Silicon Photovoltaic Module Recycling Processes

Recycling is an important circular economy strategy, and for photovoltaics (PV), the one that has received the greatest research attention. Recycling of PV modules is required in Europe; everywhere else it competes in the market of end-of-life options, where cost is a primary decision factor. The vast majority of PV modules sold globally are crystalline-silicon (c-Si); most of the rest of the market are cadmium telluride thin film modules whose primary manufacturer runs its own commercial-scale recycling program. While many different c-Si recycling approaches and technologies have been proposed, they generally lack accompanying cost estimates or enough process information to model costs. Herein we develop detailed estimates of seven categories of capital and operating costs along with estimates of revenue from recovered materials for each step in two proposed recycling processes for c-Si PV modules. Using these results, we develop a hypothetical third recycling process merging process steps from the original two, estimate surcharges required to achieve minimum sustainable prices for each recycling process, as well as consider how economies of scale could reduce costs. Increasing the purity of and identifying higher-value markets for recovered materials are approaches to reducing costs and increasing recycling rates in voluntary markets.

crystalline silicon↗
DOE OSTI2022

Impact of acetic acid exposure on metal contact degradation of different crystalline silicon solar cell technologies

Degradation due to acetic acid in photovoltaic (PV) modules has been a commonly observed phenomenon for both damp-heat exposure and outdoor operations. Acetic acid is a degradation byproduct of ethylene-vinyl acetate (EVA), a common module encapsulant. To address this issue, robust metallization pastes and cell technologies are being developed. However, it is important to assess how these technologies perform in an acetic acid environment and withstand degradation before they are implemented in the solar market. In this work, we investigate the impact of acetic acid exposure on four different cell groups: monofacial passivated emitter and rear contact (PERC) cells with advanced telluride-based front contact pastes, bifacial PERC cells with novel aluminum rear contact pastes, bifacial tunnel oxide passivated contacts (TOPCon) cells, and silicon heterojunction (SHJ) cells. These cells were exposed to acetic acid for different time increments. The recombination losses were characterized by Suns-VOC, and multi-variate regression analysis of intensity-dependent photoluminescence (PL) images with Griddler AI. Resistive losses were tracked with the transmission line method (TLM). Samples showing severe performance degradation were selected for further materials characterization to understand the root cause. Top-down and cross-sectional scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and X-ray photoelectron spectroscopy (XPS) were performed to investigate the change in materials properties. Our study shows that the front contacts of the bifacial TOPCon cells and monofacial PERC cells were significantly affected by acetic acid exposure. Here, the SHJ cells were found to be the most stable.

14 SOLAR ENERGY↗
DOE OSTI2021

Understanding and design of spin-driven thermoelectrics

While progress in thermoelectric materials based on the engineering of electronic and phononic characteristics is reaching a plateau, the addition of the spin degree of freedom has the potential to open a new landscape for alternative thermoelectric materials. Here, we present the concepts, current understanding, and guidelines for designing spin-driven thermoelectrics. We show that the interplay between the spin and heat currents in entropy transport via charge carriers can offer a path to enhance the electronic thermopower. The classical antiferromagnetic semiconductor manganese telluride (MnTe) is chosen as the case study due to its significant spin-mediated thermoelectric properties. We show that, although the spin-disorder scattering reduces the carrier mobility in magnetic materials, spin entropy, magnon, and paramagnon carrier drags can dominate and significantly enhance the thermoelectric power factor, and hence zT. Finally, several guidelines are drawn based on the current understanding for designing high-performance spin-driven thermoelectric materials.

42 ENGINEERING↗
DOE OSTI2022

ACuZrQ 3 (A = Rb, Cs; Q = S, Se, Te): Direct Bandgap Semiconductors and Metals with Ultralow Thermal Conductivity

ACuZrQ 3 (A = Rb, Cs; Q = S, Se, Te) were synthesized as black platelet crystals. RbCuZrS 3 , RbCuZrSe 3 , and CsCuZrS 3 crystallize in the KCuZrSe 3 structure type with space group Cmcm, and RbCuZrTe 3 and CsCuZrTe 3 crystallize in the lower symmetry space group Pnma. The tellurides exhibit a second order Jahn-Teller distortion with off-centering of Zr in its octahedral environment. The magnitude of the distortion is larger in RbCuZrTe 3 than in CsCuZrTe 3 . The structures of beta-CsCuS 4 and Rb 2 Cu 5 Te 5 were also determined. CsCuZrS 3 melts at 910 C-circle and exhibits partial decomposition upon heating at 275 C-circle, while CsCuZrTe 3 melts incongruently. Our DFT calculations of RbCuZrQ 3 (Q = S, Se) and CsCuZrS 3 indicate direct gap semiconductors in agreement with experiments. ACuZrTe 3 (A = Rb, Cs) were calculated to be metals which was confirmed for RbCuZrTe 3 with variable temperature conductivity measurements and consistent with heat capacity measurements. Spectroscopic measurements found a bandgap and work function of 1.44(5) eV and 4.89(5) eV for RbCuZrS 3 and 0.95(5) eV and 4.67(5) eV for RbCuZrSe 3 , respectively. Finally, RbCuZrTe 3 did not exhibit an optical bandgap and has a work function of 4.64(5) eV. RbCuZrTe 3 exhibits a low thermal conductivity under 0.5 W m -1 K -1 at room temperature.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Identifying Band Inversions in Topological Materials Using Diffusion Monte Carlo

Topological insulators are characterized by insulating bulk states and robust metallic surface states. Band inversion is a hallmark of topological insulators. At time-reversal invariant points in the Brillouin zone, spin–orbit coupling (SOC) induces a swapping of orbital character at the bulk band edges. Reliably detecting band inversion in solid-state systems with many-body methods would aid in identifying possible candidates for spintronics and quantum computing applications and improve our understanding of the physics behind topologically nontrivial systems. Density functional theory (DFT) methods are a well-established means of investigating these interesting materials due to their favorable balance of computational cost and accuracy but often struggle to accurately model the electron–electron correlations present in the many materials containing heavier elements. In this work, we develop a novel method to detect band inversion within continuum quantum Monte Carlo (QMC) methods that can accurately treat the electron correlation and spin–orbit coupling that are crucial to the physics of topological insulators. Our approach applies a momentum-space-resolved atomic population analysis throughout the first Brillouin zone utilizing the Löwdin method and the one-body reduced density matrix produced with diffusion Monte Carlo (DMC). We integrate this method into QMCPACK, an open source ab initio QMC package, so that these ground-state methods can be used to complement experimental studies and validate prior DFT work on predicting the band structures of correlated topological insulators. Here, we demonstrate this new technique on the topological insulator bismuth telluride, which displays band inversion between its Bi-p and Te-p states at the Γ-point. We show an increase in charge on the bismuth-p orbital and a decrease in charge on the tellurium-p orbital when comparing band structures with and without SOC. Additionally, we use our method to compare the degree of band inversion present in monolayer Bi 2 Te 3 , which has no interlayer van der Waals interactions, to that seen in the bilayer and bulk. The method presented here will enable future many-body studies of band inversion that can shed light on the delicate interplay between correlation and topology in correlated topological materials.

Band structure↗
DOE OSTI2021

Dielectric Screening Modulates Semiconductor Nanoplatelet Excitons

The influence of external dielectric environments is well understood for 2D semiconductor materials but overlooked for colloidally grown II–VI nanoplatelets (NPLs). In this work, we synthesize MX (M = Cd, Hg; X = Se, Te) NPLs of varying thicknesses and apply the Elliott model to extract exciton binding energies—reporting values in good agreement with prior methods and extending to less studied cadmium telluride and mercury chalcogenide NPLs. Here, we find that the exciton binding energy is modulated both by the relative effect of internal vs external dielectric and by the thickness of the semiconductor material. An analytical model shows dielectric screening increases the exciton binding energy relative to the bulk by distorting the Coulombic potential across the NPL surface. We further confirm this effect by decreasing and recovering the exciton binding energy of HgTe NPLs through washing in polarizable solvents. Our results illustrate NPLs are colloidal analogues of van der Waals 2D semiconductors and point to surface modification as an approach to control photophysics and device properties.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Synthesis of Tunable SnS-TaS 2 Nanoscale Superlattices

Nanoscale superlattices represent a compelling platform for designed materials as the specific identity and spatial arrangement of constituent layers can lead to tunable properties. A number of kinetically stabilized, nonepitaxial superlattices with almost limitless structural tunability have been reported in telluride and selenide chemistries but have not yet been extended to sulfides. Here, we present SnS-TaS 2 nanoscale superlattices with tunable layer architecture. Layered amorphous precursors are prepared as thin films programmed to mimic the targeted superlattice; subsequent low temperature annealing activates self-assembly into crystalline nanocomposites. We investigate structure and composition of superlattices comprised of monolayers of TaS 2 and 3–7 monolayers of SnS per repeating unit. Furthermore, a graded precursor preparation approach is introduced, allowing stabilization of superlattices with multiple stacking sequences in a single preparation. Controlled synthesis of the architecture of nanoscale superlattices is a critical path toward tuning their exotic properties and enabling integration with electronic, optical, or quantum devices.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Sputtered p-Type Cu x Zn 1– x S Back Contact to CdTe Solar Cells

As thin-film cadmium telluride (CdTe) solar cells gain prominence, one particular challenge is optimizing contacts and their interfaces to transfer charge without losses in efficiency. Back contact recombination is still significant and will prevent CdTe solar technology from reaching its full potential in device efficiency, and transparent back contacts have not been developed for bifacial solar technology or multijunction solar cells. To address these challenges, here we investigate sputtered Cu x Zn 1– x S as a p-type semi-transparent back contact material to thin-film polycrystalline CdTe solar cells at Cu concentrations x = 0.30, 0.45, and 0.60. This material is selected for its high hole conductivity (160–2120 S cm –1 ), wide optical band gap (2.25–2.75 eV), and variable ionization potential (approximately 6–7 eV) that can be aligned to that of CdTe. We report that without device optimization, CdTe solar cells with these Cu x Zn 1– x S back contacts perform as well as control cells with standard ZnTe:Cu back contacts. We observe no reduction in external quantum efficiency, low contact barrier heights of approximately 0.3 eV, and carrier lifetimes on par with those of baseline CdTe. These cells are relatively stable over one year in air, with V OC and efficiency of the x = 0.30 cell decreasing by only 1 and 3%, respectively. Using scanning electron microscopy and scanning transmission electron microscopy to investigate the Cu x Zn 1– x S/CdTe interface, we demonstrate that the Cu x Zn 1– x S layer segregates into a bilayer of Cu-Te-S and Zn-Cd-S, and thermodynamic reaction calculations support these findings. Despite its bilayer formation, the back contact still functions well. This investigation explains some of the physical mechanisms governing the device stack, inspires future work to understand interfacial chemistry and charge transfer, and elicits optimization to achieve higher-efficiency CdTe cells.

14 SOLAR ENERGY↗
DOE OSTI2025

Doping in Efficient Polycrystalline CdSeTe Solar Cells via AsCl 3 Vapor Annealing

Doping in cadmium telluride (CdTe) thin-film solar cells is a critical step in producing highly efficient CdTe solar modules. To date, copper (Cu) ex-situ diffusion doping and group V in situ doping (such as arsenic, As) have been effectively used in manufacturing CdTe solar modules. However, Cu doping is prone to rapid degradation, whereas the low activation ratio of the dopants constrains group V in situ doping. Recently, ex-situ group V doping has been developed, showing an improved doping activation ratio through a solution process. Here, in this study, we developed a vapor-based AsCl 3 doping method for diffusion doping of polycrystalline CdSeTe devices. AsCl 3 vapor annealing can promote the diffusion of As into the bulk CdSeTe through a surface chemical reaction between CdTe and AsCl 3 . This approach has led to a long carrier lifetime of over 72 ns, V oc of 850 mV, and power conversion efficiency of ~18% with Au metal electrodes. The vapor-based ex situ group V doping approach offers an effective means to perform group V diffusion doping into the CdSeTe device.

14 SOLAR ENERGY↗
DOE OSTI2025

Atomic Structure, Dynamics, Changes in Chemical Bonding and Semiconductor-Metal Transition in Sb 2 Se 3 : A Remarkable Material for Quantum Networks and Energy Applications

Antimony sesquiselenide has become an outstanding functional material for photovoltaics, energy storage and transformation, memory and photonic applications. Sb 2 Se 3 is one of the most successful emerging solar light absorbers and has also been identified as a highly promising ultralow-loss phase-change material (PCM) for next-generation coherent nanophotonic processors, photonic tensor cores, quantum and neuromorphic networks. Unlike benchmark telluride PCMs, Sb 2 Se 3 features a quasi-one-dimensional (1D) crystalline structure consisting of (Sb 4 Se 6 ) ∞ ribbons, lacks the typical PCM chemical bonding, and undergoes an extended semiconductor-metal transition above the melting point. Consequently, the origin of high optical contrast between crystalline (SET) and amorphous (RESET) logic states remains elusive and presents a significant challenge. Using high-energy X-ray diffraction and Raman spectroscopy over a wide temperature range, supported by first-principles simulations and complemented by thermal, optical and electrical measurements, as well as by 121 Sb-Mossbauer spectroscopy, the quasi-1D network of orthorhombic antimony sesquiselenide was found to undergo significant evolution in amorphous and supercooled Sb 2 Se 3 , leading to lower coordination, shorter interatomic distances and a higher p-electron density on antimony, indicating changes in chemical bonding. The observed novel Sb 2 Se 3 nanocrystalline polymorph, characterized by trigonal antimony coordination and more isolated Sb-Se ribbons, could help reduce multiple trapping defect states in the bandgap, which are typical of orthorhombic Sb 2 Se 3 , thereby enhancing the power-conversion efficiency of photovoltaic devices. Semimetallic and metallic liquid Sb 2 Se 3 exhibit a gradual transformation into a denser 2D and/or 3D network with higher antimony coordination. Localized electron states in the pseudogap are becoming extended, leading to an increase in electronic conductivity σ following the relationship σ ∝ N(E F ) 2 . Liquid Sb 2 Se 3 also appears to be strongly fragile, with a nonmonotonic change in viscosity and higher atomic mobility in the metallic liquid. Furthermore, these results explain extraordinary functionalities of Sb 2 Se 3 for photonic and energy applications.

antimony↗
DOE OSTI2025

Magnetic Proximity Effects in Iron Germanium Telluride/Platinum Heterostructures

Van der Waals (vdW) magnetic materials have attracted considerable attention for use in spintronic devices such as those controlled by spin–orbit torque (SOT). Such SOT-driven devices are typically fabricated by bringing a vdW magnet in proximity to a spin–charge conversion layer to achieve current-driven magnetization switching. Here, we show that such structures fabricated with iron germanium telluride (FGT) and platinum can exhibit emergent magnetic properties, which we attribute to magnetic proximity effects at the FGT/Pt interface. These changes manifest as increased perpendicular magnetic anisotropy and the emergence of additional magnetization reversal steps as probed by magneto-transport, with the most significant changes appearing in thinner flakes. The behavior was found to be robust and consistently appeared in samples made with crystals from different vendors. In conclusion, our results demonstrate the potential for engineering vdW spintronic systems through magnetic proximity effects.

2D magnet↗
DOE OSTI2025

Quantum Imaging of Ferromagnetic van der Waals Magnetic Domain Structures at Ambient Conditions

Recently discovered 2D van der Waals magnetic materials, and specifically iron–germanium–telluride (Fe5GeTe2), have attracted significant attention both from a fundamental perspective and for potential applications. Key open questions concern their domain structure and magnetic phase transition temperature as a function of sample thickness and external field, as well as implications for integration into devices such as magnetic memories and logic. Here we address key questions using a nitrogen-vacancy center based quantum magnetic microscope, enabling direct imaging of the magnetization of Fe5GeTe2 at submicrometer spatial resolution as a function of temperature, magnetic field, and thickness. This quantum imaging technique provides noninvasive, high-sensitivity measurements with high spatial resolution under ambient conditions, making it particularly well suited for probing 2D magnets. We employ spatially resolved measures, including magnetization variance and cross-correlation, and find a significant spread in transition temperature yet with no clear dependence on thickness down to 15 nm. We also identify previously unknown stripe features in the optical as well as magnetic images, which we attribute to modulations of the constituting elements during crystal synthesis and subsequent oxidation. Our results suggest that the magnetic anisotropy in this material does not play a crucial role in their magnetic properties, leading to a magnetic phase transition of Fe5GeTe2 which is largely thickness-independent down to 15 nm. Our findings could be significant in designing future spintronic devices, magnetic memories, and logic with 2D van der Waals magnetic materials.

Bindu, Bindu [Hebrew University of Jerusalem, Isra↗
DOE OSTI2024

Evaporated CdSe for Efficient Polycrystalline CdSeTe Thin-Film Solar Cells

Recent progress has shown that alloying cadmium telluride (CdTe) with cadmium selenide (CdSe) to create a CdSexTe1-x (CdSeTe) gradient region can significantly boost the performance of polycrystalline CdSeTe thin-film solar cells. However, improper CdSeTe alloying might introduce problematic band alignment and deleterious voids at the front interface, limiting the benefit maximization of this technique. Here, we show that the CdSe layers deposited by thermal evaporation result in CdSeTe cells with a higher performance than the sputtered CdSe. This is because evaporated CdSe can avoid the formation of voids at the front interface, producing improved front junction quality with suppressed front junction nonradiative recombination. The champion cell using evaporated CdSe demonstrated a power conversion efficiency (PCE) of 19.7%, much higher than 18.1% in the cell using sputtered CdSe.

cadmium selenide↗
DOE OSTI2021

High-specific-power flexible transition metal dichalcogenide solar cells

Abstract Semiconducting transition metal dichalcogenides (TMDs) are promising for flexible high-specific-power photovoltaics due to their ultrahigh optical absorption coefficients, desirable band gaps and self-passivated surfaces. However, challenges such as Fermi-level pinning at the metal contact–TMD interface and the inapplicability of traditional doping schemes have prevented most TMD solar cells from exceeding 2% power conversion efficiency (PCE). In addition, fabrication on flexible substrates tends to contaminate or damage TMD interfaces, further reducing performance. Here, we address these fundamental issues by employing: (1) transparent graphene contacts to mitigate Fermi-level pinning, (2) MoO x capping for doping, passivation and anti-reflection, and (3) a clean, non-damaging direct transfer method to realize devices on lightweight flexible polyimide substrates. These lead to record PCE of 5.1% and record specific power of 4.4 W g −1 for flexible TMD (WSe 2 ) solar cells, the latter on par with prevailing thin-film solar technologies cadmium telluride, copper indium gallium selenide, amorphous silicon and III-Vs. We further project that TMD solar cells could achieve specific power up to 46 W g −1 , creating unprecedented opportunities in a broad range of industries from aerospace to wearable and implantable electronics.

42 ENGINEERING↗
DOE OSTI2024

Anomalous lattice thermal conductivity increase with temperature in cubic GeTe correlated with strengthening of second-nearest neighbor bonds

Understanding thermal transport mechanisms in phase change materials is critical to elucidating the microscopic picture of phase transitions and advancing thermal energy conversion and storage. Experiments consistently show that cubic phase germanium telluride (GeTe) has an unexpected increase in lattice thermal conductivity with rising temperature. Despite its ubiquity, resolving its origin has remained elusive. In this work, we carry out temperature-dependent lattice thermal conductivity calculations for cubic GeTe through efficient, high-order machine-learned models and additional corrections for coherence effects. We corroborate the calculated phonon properties with our inelastic X-ray scattering measurements. Our calculated lattice thermal conductivity values agree well with experiments and show a similar increasing trend. Through additional bonding strength calculations, we propose that a major contributor to the increasing lattice thermal conductivity is the strengthening of second-nearest neighbor interactions. The findings herein serve to deepen our understanding of thermal transport in phase-change materials.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Understanding What Limits the Voltage of Polycrystalline CdSeTe Solar Cells

The origin of voltage deficits in polycrystalline cadmium selenide telluride (CdSeTe) solar cells is unclear. Here, we present a comprehensive voltage loss analysis performed on state-of-the-art CdSeTe devices - fabricated at Colorado State University and First Solar - using photoluminescence techniques, including external radiative efficiency (ERE) measurements. More specifically, we report the thermodynamic voltage limit Voc,ideal, internal voltage iVoc and external voltage Voc of partially and fully finished cells fabricated with different dopant species, dopant concentrations and back contacts. Arsenic-doped aluminium-oxide-passivated cells made at Colorado State University present remarkably high ERE (>1%) - translating into iVoc above 970 mV - but suffer from poor back-contact selectivity. On the other hand, arsenic-doped devices from First Solar present almost perfect carrier selectivity (Voc=iVoc), leading to Voc above 840 mV, and are limited by recombination in various parts of the device. Thus, development of contact structures that are both passivating and selective in combination with highly luminescent absorbers is key to reducing voltage losses.

CdSeTe devices↗