Search NASA⌕ Search

SEARCH · Search NASA

Results for “Thermodynamic Data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Chemical and Thermal Nonequilibrium Heat-Transfer Analysis for Hypervelocity, Low Reynolds Number Flow

Chemical and thermal nonequilibrium phenomena are studied in the stagnation region of a hypervelocity blunt body. This investigation is motivated by the need to predict the heat-transfer rate to the leading edge of aeromaneuvering orbital transfer vehicles. Flight speeds of approximately 10 km/s at altitudes of approximately 80 km are considered for body radii of 1-50 cm. The analysis is based on continuum theory and is applicable to the viscous and incipient merged layer regimes of rarefied flow. A two-species, two-temperature gas model is assumed. Comparisons are made with previous theories, experimental data, and results based on the thermodynamic equilibrium assumption. The equation accounting for vibrational nonequilibrium is presented and its effects on flow properties are discussed. Parameters requiring further investigation are identified. Preliminary results indicate that the inclusion of vibrational relaxation has little effect on the heat-transfer rate for a fully catalytic surface. However, vibrational nonequilibrium may increase the heat-transfer rate to a noncatalytic surface, depending on the degree of nonequilibrium.

Brown, Kevin G.↗
NASA NTRS1999

The Lightning Imaging Sensor

The Lightning Imaging Sensor (LIS) is a NASA Earth Observing System (EOS) instrument on the Tropical Rainfall Measuring Mission (TRMM) platform designed to acquire and investigate the distribution and variability of total lightning (i.e., cloud-to-ground and intracloud) between q35' in latitude. Since lightning is one of the responses of the atmosphere to thermodynamic and dynamic forcing, the LIS data is being used to detect deep convection without land-ocean bias, estimate the precipitation mass in the mixed phased region of thunderclouds, and differentiate storms with strong updrafts from those with weak vertical motion.

Christian, Hugh J.↗
NASA NTRS1999

Thermodynamic Modeling and Analysis of Human Stress Response

A novel approach based on the second law of thermodynamics is developed to investigate the psychophysiology and quantify human stress level. Two types of stresses (thermal and mental) are examined. A Unified Stress Response Theory (USRT) is developed under the new proposed field of study called Engineering Psychophysiology. The USRT is used to investigate both thermal and mental stresses from a holistic (human body as a whole) and thermodynamic viewpoint. The original concepts and definitions are established as postulates which form the basis for thermodynamic approach to quantify human stress level. An Objective Thermal Stress Index (OTSI) is developed by applying the second law of thermodynamics to the human thermal system to quantify thermal stress or dis- comfort in the human body. The human thermal model based on finite element method is implemented. It is utilized as a "Computational Environmental Chamber" to conduct series of simulations to examine the human thermal stress responses under different environmental conditions. An innovative hybrid technique is developed to analyze human thermal behavior based on series of human-environment interaction simulations. Continuous monitoring of thermal stress is demonstrated with the help of OTSI. It is well established that the human thermal system obeys the second law of thermodynamics. Further, the OTSI is validated against the experimental data. Regarding mental stress, an Objective Mental Stress Index (OMSI) is developed by applying the Maxwell relations of thermodynamics to the combined thermal and cardiovascular system in the human body. The OMSI is utilized to demonstrate the technique of monitoring mental stress continuously and is validated with the help of series of experimental studies. Although the OMSI indicates the level of mental stress, it provides a strong thermodynamic and mathematical relationship between activities of thermal and cardiovascular systems of the human body.

Boregowda, S. C.↗
NASA NTRS2001

A Nanometer Aerosol Size Analyzer (nASA) for Rapid Measurement of High-Concentration Size Distributions

We have developed a fast-response Nanometer Aerosol Size Analyzer (nASA) that is capable of scanning 30 size channels between 3 and 100 nm in a total time of 3 seconds. The analyzer includes a bipolar charger (P0210), an extended-length Nanometer Differential Mobility Analyzer (Nano-DMA), and an electrometer (TSI 3068). This combination of components provides particle size spectra at a scan rate of 0.1 second per channel free of uncertainties caused by response-time-induced smearing. The nASA thus offers a fast response for aerosol size distribution measurements in high-concentration conditions and also eliminates the need for applying a de-smearing algorithm to resulting data. In addition, because of its thermodynamically stable means of particle detection, the nASA is useful for applications requiring measurements over a broad range of sample pressures and temperatures. Indeed, experimental transfer functions determined for the extended-length Nano-DMA using the Tandem Differential Mobility Analyzer (TDMA) technique indicate the nASA provides good size resolution at pressures as low as 200 Torr. Also, as was demonstrated in tests to characterize the soot emissions from the J85-GE engine of a T38 aircraft, the broad dynamic concentration range of the nASA makes it particularly suitable for studies of combustion or particle formation processes. Further details of the nASA performance as well as results from calibrations, laboratory tests and field applications are presented.

Han, Hee-Siew↗
NASA NTRS2013

Chemical Heterogeneity of a Large Cluster IDP: Clues to its Formation History Using X-ray Fluorescence Mapping and XANES Spectroscopy

Chondritic porous IDPs may be among the most primitive objects found in our solar system [1]. They consist of many micron to submicron minerals, glasses and carbonaceous matter [2,3,4,5,6,7] with > 10(exp 4) grains in a 10 micron cluster [8]. Speculation on the environment where these fine grained, porous IDPs formed varies with possible sources being presolar dusty plasma clouds, protostellar condensation, solar asteroids or comets [4,6,9]. Also, fine grained dust forms in our solar system today [10,11]. Isotopic anomalies in some particles in IDPs suggest an interstellar source[4,7,12]. IDPs contain relic particles left from the dusty plasma that existed before the protostellar disk formed and other grains in the IDPs formed later after the cold dense nebula cloud collapsed to form our protostar and other grains formed more recently. Fe and CR XANES spectroscopy is used here to investigate the oxygen environment in a large (>50 10 micron or larger sub-units) IDP. Conclusions: Analyzing large (>50 10 micron or larger sub-units) CP IDPs gives one a view on the environments where these fine dust grains formed which is different from that found by only analyzing the small, 10 micron IDPs. As with cluster IDP L2008#5 [3], L2009R2 cluster #13 appears to be an aggregate of grains that sample a diversity of solar and perhaps presolar environments. Sub-micron, grain by grain measurement of trace element contents and elemental oxidation states determined by XANES spectroscopy offers the possibility of understanding the environments in which these grains formed when compared to standard spectra. By comparing thermodynamic modeling of condensates with analytical data an understanding of transport mechanisms operating in the early solar system may be attained.

Wirick, S.↗
NASA NTRS2015

The Prospective Search for Highly Ionized Technetium in Hot (pre-) White Dwarfs

The discovery of technetium (Tc) in the atmospheres of red giants by Merrill (1952, ApJ, 116, 21) constituted convincing proof that s-process nucleosynthesis is indeed occurring in evolved stars. In principle, Tc should still be present in the atmospheres of hot post-AGB stars and (pre-) white dwarfs although, due to radioactive decay, it should be present in decreasing quantities along post-AGB evolution. The recent discovery of a large number of trans-iron group elements in hot white dwarfs with atomic numbers in the range A = 30-56 (Zn to Ba) raises the prospect that Tc (A = 43) may also be detected. However, this is currently not feasible because no atomic data exist for ionization stages beyond Tc ii. As an initial step, we calculated atomic energy levels and oscillator strengths of Tc iv-vi and used these data to compute non-local thermodynamic equilibrium (NLTE) model atmospheres to estimate at which minimum abundance level Tc could be detected. We show that Tc lines can be found in ultraviolet spectra of hot white dwarfs provided Tc is as abundant as other detected trans-Fe elements. We find that radiative levitation can keep Tc in large, easily detectable quantities in the atmosphere. A direct identification of Tc lines is still not feasible because wavelength positions cannot be computed with necessary precision. Laboratory measurements are necessary to overcome this problem. Our results suggest that such efforts are beneficial to the astrophysical community.

prospective↗
NASA NTRS2016

Improving Free-Piston Stirling Engine Power Density

Analyses and experiments demonstrate the potential benefits of optimizing piston and displacer motion in a free piston Stirling Engine. Isothermal analysis shows the theoretical limits of power density improvement due to ideal motion in ideal Stirling engines. More realistic models based on nodal analysis show that ideal piston and displacer waveforms are not optimal, often producing less power than engines that use sinusoidal piston and displacer motion. Constrained optimization using nodal analysis predicts that Stirling engine power density can be increased by as much as 58% using optimized higher harmonic piston and displacer motion. An experiment is conducted in which an engine designed for sinusoidal motion is forced to operate with both second and third harmonics, resulting in a maximum piston power increase of 14%. Analytical predictions are compared to experimental data showing close agreement with indirect thermodynamic power calculations, but poor agreement with direct electrical power measurements.

Stirling engines↗
NASA NTRS2017

Climatological Study of the Short-Term Variation of the 0 C, -10 C, AND -20 C Altitude Levels Over the Florida Spaceport

For evaluation of the potential of cloud electrification, it is necessary to know the altitude of the 0, -10 and -20 degree Celsius levels. Cape Canaveral Air Force Station has recorded balloon launch data back to 1989. In support of rocket launches, often multiple balloons are launched within minutes of each other in the 4-6 hours leading up to launch. In the past, temperature data from sondes was typically available every hour or so through the launch countdown, allowing for frequent updates of these critical temperature thresholds. Recently, launch customers are relying on jimsphere and wind profiler data that do not have a thermodynamic component in the latter 4-6 hours of a countdown. This study compares the altitude differences of the 0, -10 and -20 degree Celsius levels from GPS-tracked consecutive balloon pairs not to exceed 6 hours apart. The analysis uses 3,198 soundings from 2001 to 2013. Approximately 20, 17, and 13 percent of the time the altitude of the temperature level in question (0, -10, -20 degrees C respectively), varies by more than 500 feet (operationally significant threshold) within 6 hours. This study analyzes the altitude variability as a function of several meteorological parameters, such as dew point depression and solar zenith angle. Additionally, the study concludes with impacts to launch operations.

altitude of 0 degree C temperature level↗
NASA NTRS2016

Improving Power Density of Free-Piston Stirling Engines

Analyses and experiments demonstrate the potential benefits of optimizing piston and displacer motion in a free piston Stirling Engine. Isothermal analysis shows the theoretical limits of power density improvement due to ideal motion in ideal Stirling engines. More realistic models based on nodal analysis show that ideal piston and displacer waveforms are not optimal, often producing less power than engines that use sinusoidal piston and displacer motion. Constrained optimization using nodal analysis predicts that Stirling engine power density can be increased by as much as 58 using optimized higher harmonic piston and displacer motion. An experiment is conducted in which an engine designed for sinusoidal motion is forced to operate with both second and third harmonics, resulting in a maximum piston power increase of 14. Analytical predictions are compared to experimental data showing close agreement with indirect thermodynamic power calculations, but poor agreement with direct electrical power measurements.

space technology↗
NASA NTRS2017

Climatological Study of the Short-Term Variation of the 0 C, -10 C, and -20 C Altitude Levels over the Florida Spaceport

For evaluation of the potential of cloud electrification, it is necessary to know the altitude of the 0, -10 and -20 degree Celsius levels. Cape Canaveral Air Force Station has recorded balloon launch data back to 1989. In support of rocket launches, often multiple balloons are launched within minutes of each other in the 4-6 hours leading up to launch. In the past, temperature data from sondes was typically available every hour or so through the launch countdown, allowing for frequent updates of these critical temperature thresholds. Recently, launch customers are relying on Jimsphere and wind profiler data that do not have a thermodynamic component in the latter 4-6 hours of a countdown. This study compares the altitude differences of the 0, -10 and -20 degree Celsius levels from consecutive balloon pairs not to exceed 6 hours apart. The analysis uses 9685 soundings from 1989 to 2013. Approximately 5 of the time the altitude of the temperature level in question (0, -10, -20 degrees C), varies by more than 500 feet (operationally significant threshold) within 6 hours. This study analyzes the altitude variability as a function of several meteorological parameters, such as change in sonde type, dew point depression, and solar zenith angle. Additionally, the study concludes with impacts to launch operations.

Huddleston, Lisa L.↗
NASA NTRS2018

Analysis of the Honeywell Uncertified Research Engine (HURE) with Ice Crystal Cloud Ingestion at Simulated Altitudes: Public Version

The Honeywell Uncertified Research Engine (HURE), a research version of a turbofan engine that never entered production, was tested in the NASA Propulsion System Laboratory (PSL), an altitude test facility at the NASA Glenn Research Center. The PSL is a facility that is equipped with water spray bars capable of producing an ice cloud consisting of ice particles, having a controlled particle diameter and concentration in the air flow. In preparation for testing of the HURE, numerical analysis of flow and ice particle thermodynamics was performed on the compression system of the turbofan engine to predict operating conditions that could potentially result in a risk of ice accretion due to ice crystal ingestion. The results of those analyses formed the basis of the test matrix. The goal of the test matrix was to have ice accrete in two regions of the compression system: region one, which consists of the fan-stator through the inlet guide vane (IGV), and region two which is the first stator within the high pressure compressor. The predictive analyses were performed with the mean line compressor flow modeling code (COMDES-MELT) which includes an ice particle model. Together these comprise a one-dimensional icing tool. The HURE engine was tested in PSL with the ice cloud over the range of operating conditions of altitude, ambient temperature, simulated flight Mach number, and fan speed with guidance from the analytical predictions. The engine was fitted with video cameras at strategic locations within the engine compression system flow path where ice was predicted to accrete, in order to visually confirm ice accretion when it occurred. In addition, traditional compressor instrumentation such as total pressure and temperature probes, static pressure taps, and metal temperature thermocouples were installed in targeted areas where the risk of ice accretion was expected. The current research focuses on the analysis of the data that was obtained after testing the HURE engine in PSL with ice crystal ingestion. The computational method was enhanced by computing key parameters through the fan-stator at multiple spanwise locations, in order to increase the fidelity with the current mean-line method. In addition, other sources of heat (non-adiabatic walls) were suspected to be the cause of accretion near the splitter-lip and shroud. Since there were no thermocouples near the splitter, a simple order of magnitude heat transfer model was implemented to estimate the wall temperature. Future analyses will require a higher fidelity thermal analysis of the compression system metal walls to accurately calculate the total heat flux to the ice particle. For many data points analyzed, there were differences between the thermodynamic system model and the measured test data that may partially be responsible for uncertainties with the results of the current analyses.

Turbomachinery↗
NASA NTRS1992

Comparing the results of an analytical model of the no-vent fill process with no-vent fill test results for a 4.96 cu m (175 cu ft) tank

NASA-Lewis has been investigating a no-vent fill method for refilling cryogenic storage tanks in low gravity. Analytical modeling based on analyzing the heat transfer of a droplet has successfully represented the process in 0.034 and 0.142 sq m commercial dewars using liquid nitrogen and hydrogen. Recently a large tank (4.96 sq m) was tested with hydrogen. This lightweight tank is representative of spacecraft construction. This paper presents efforts to model the large tank test data. The droplet heat transfer model is found to overpredict the tank pressure level when compared to the large tank data. A new model based on equilibrium thermodynamics has been formulated. This new model is compared to the published large scale tank's test results as well as some additional test runs with the same equipment. The results are shown to match the test results within the measurement uncertainty of the test data except for the initial transient wall cooldown where it is conservative (i.e., overpredicts the initial pressure spike found in this time frame).

Taylor, William J.↗
NASA NTRS1993

Comparing the results of an analytical model of the no-vent fill process with no-vent fill test results for a 4.96 cubic meters (175 cubic feet) tank

The NASA Lewis Research Center (NASA/LeRC) have been investigating a no-vent fill method for refilling cryogenic storage tanks in low gravity. Analytical modeling based on analyzing the heat transfer of a droplet has successfully represented the process in 0.034 m and 0.142 cubic m commercial dewars using liquid nitrogen and hydrogen. Recently a large tank (4.96 cubic m) was tested with hydrogen. This lightweight tank is representative of spacecraft construction. This paper presents efforts to model the large tank test data. The droplet heat transfer model is found to over predict the tank pressure level when compared to the large tank data. A new model based on equilibrium thermodynamics has been formulated. This new model is compared to the published large scale tank's test results as well as some additional test runs with the same equipment. The results are shown to match the test results within the measurement uncertainty of the test data except for the initial transient wall cooldown where it is conservative (i.e., overpredicts the initial pressure spike found in this time frame).

Taylor, William J.↗
NASA NTRSDate not supplied

Calcium and Magnesium Distribution Between Sulfide and Silicate Melts: Thermodynamic Modeling and Insights into Mercury's Mantle-Crust Differentiation

Mercury stands out as the terrestrial planet with the lowest degree of oxidation among all planets of our solar system. It is characterized by a high abundance of sulfur, which is expected to replace oxygen in silicate melts. This sulfur enrichment could lead to sulfide saturation in its mantle, potentially resulting in the formation of sulfides rich in calcium and magnesium. Utilizing experimental data from the literature, we constructed a thermodynamic model to explore the partitioning of calcium and magnesium between sulfide and silicate melts. This model aims to improve our comprehension of the chemical equilibria driving the process of mantle-crust differentiation on Mercury. Our models indicate that increased temperature, decreased pressure, and low concentrations of iron, oxygen, and carbon within the sulfide phase, along with low sulfur concentrations in the silicate phase, favor calcium’s partitioning into the sulfide. Additionally, magnesium partitioning into the sulfide melt is favored with decreased pressure, decreased temperature, low concentrations of iron and calcium within the sulfide, and low concentrations of sulfur within the silicate. Our results suggest that up 9.4% and 5.6% Ca and Mg, respectively, can be present in sulfides equilibrated with sulfide-saturated silicate melts during mantle-crust differentiation. Further investigation will focus on the distribution of sulfide phases within the mantle and crust to better constrain Mercury’s internal structure.

Taylor McCombs↗
NASA NTRSDate not supplied

A General Model for the Electrochemical Double Layer in Solids

It has long been clear that electrochemical double layer / space charge zone in the vicinity of interfaces and other extended defects greatly influences transport and reactivity. Over the past several years, multiple microscopic measurements of defect concentrations in the vicinity of solid-solid interfaces made clear that dilute-case thermodynamic theories to describe the behavior of charged species in space charge zones are untenable. Inhomogeneous thermodynamics – i.e., phase field models – have delivered the most success in describing both microscopic and macroscopic experiments. We still need a generalized approach that quantitatively reproduces the microscopic and macroscopic evidence, while remaining accessible to a wide range of researchers and engineers. In my talk I will present such a framework, which builds on the previously introduced Poisson-Cahn theory but utilizes data science methods which come into the thermodynamic framework in a well-defined way. I will review recent applications to both microscopic and macroscopic datasets while previewing our plans for connecting the theory to atomistic / first principles calculations and experiment simultaneously. I will also review plans for releasing open source code that runs on desktop-level computational resources.

David Mebane↗
NASA NTRS1972

Binary chromatographic data and estimation of adsorbent porosities

Data for the system n-pentane/n-heptane on porous Chromosorb-102 adsorbent were obtained at 150, 175, and 200 C for mixtures containing zero to 100% n-pentane by weight. Prior results showing limitations on superposition of pure component data to predict multicomponent chromatograms were verified. The thermodynamic parameter MR0 was found to be a linear function of sample composition. A nonporous adsorbent failed to separate the system because of large input sample dispersions. A proposed automated data processing scheme involving magnetic tape recording of the detector signals and processing by a minicomputer was rejected because of resolution limitations of the available a/d converters. Preliminary data on porosity and pore size distributions of the adsorbents were obtained.

Meisch, A. J.↗
NASA NTRS2011

Diagnosing AIRS Sampling with CloudSat Cloud Classes

AIRS yield and sampling vary with cloud state. Careful utilization of collocated multiple satellite sensors is necessary. Profile differences between AIRS and ECMWF model analyses indicate that AIRS has high sampling and excellent accuracy for certain meteorological conditions. Cloud-dependent sampling biases may have large impact on AIRS L2 and L3 data in climate research. MBL clouds / lower tropospheric stability relationship is one example. AIRS and CloudSat reveal a reasonable climatology in the MBL cloud regime despite limited sampling in stratocumulus. Thermodynamic parameters such as EIS derived from AIRS data map these cloud conditions successfully. We are working on characterizing AIRS scenes with mixed cloud types.

model analyses↗
NASA NTRS1989

Thermodynamic properties of the heliospheric plasma

A global-scale study is conducted of the radial evolution of the solar wind's temperature (T), number density (n), and entropy (s) thermodynamic properties, on the basis of plasma data from such sources as IMP and ISEE 3, in conjunction with an MHD simulation model. The radial evolution of T and s indicates that the heliospheric plasma is subjected to a heating process; this heating is interpreted to be largely due to the cumulative effect of the shock process with increasing distance from the sun. This simulation model is also used to extrapolate the thermodynamic properties of the solar wind from Voyager 2 to the region of the outer heliosphere that is bounded by the termination shock.

Whang, Y. C.↗