SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
In this manuscript, we use density functional theory to develop thermodynamic models for super abundant vacancy (SAV) formation in delta-Pu. We find that the formation of a hydride phase will occur before reaching the H pressures needed to form a SAV phase.
Self-compensation in Ge- and Si-doped Al 0.3 Ga 0.7 N has been investigated in terms of the formation of III vacancy and donor-vacancy complexes. Both Ge- and Si-doped AlGaN layers showed a compensation knee behavior with impurity compensation (low doping regime), compensation plateau (medium doping regime), and self-compensation (high doping regime). A maximum free carrier concentration of 4–5 × 10 19 cm –3 was obtained by Ge doping, whereas Si doping resulted in only half of that value, ~2 × 10 19 cm –3 . A DFT calculation with the grand canonical thermodynamics model was developed to support the hypothesis that the difference in self-compensation arises from the difference in the formation energies of the V III -n•donor complexes relative to their onsite configurations. The model suggested that the V III -2•donor and V III -3•donor complexes were responsible for self-compensation for both Ge- and Si-doped AlGaN. However, a lower free carrier concentration in Si-doped samples was due to a high V III -3•Si concentration, resulting from a lower energy of formation of V III -3•Si.
Plutonium metal exhibits an anomalously large softening of its bulk modulus at elevated temperatures that is made all the more extraordinary by the finding that it occurs irrespective of whether the thermal expansion coefficient is positive, negative, or zero—representing an extreme departure from conventional Grüneisen scaling. We show here that the cause of this softening is the compressibility of plutonium’s thermally excited electronic configurations, which has thus far not been considered in thermodynamic models. We show that when compressible electronic configurations are thermally activated, they invariably give rise to a softening of the bulk modulus regardless of the sign of their contribution to the thermal expansion. The electronically driven softening of the bulk modulus is shown to be in good agreement with elastic moduli measurements performed on the gallium-stabilized δ phase of plutonium over a range of temperatures and compositions and is shown to grow rapidly at small concentrations of gallium and at high temperatures, where it becomes extremely sensitive to hydrostatic pressure.
The need for energy-efficient recovery of organic solutes from aqueous streams is becoming more urgent as chemical manufacturing transitions toward nonconventional and bio-based feedstocks and processes. In addition to this, many aqueous waste streams contain recalcitrant organic contaminants, such as pharmaceuticals, industrial solvents, and personal care products, that must be removed prior to reuse. We observe that rigid carbon membrane materials can remove and concentrate organic contaminants via an unusual liquid-phase membrane permeation modality. Surprisingly, detailed thermodynamic calculations on the chemical potential of the organic contaminant reveal that the organic species has a higher chemical potential on the permeate side of the membrane than on the feed side of the membrane. This unusual observation challenges conventional membrane transport theory that posits that all permeating species move from high chemical potential states to lower chemical potential states. Based on experimental measurements, we hypothesize that the organic is concentrated in the membrane relative to water via favorable binding interactions between the organic and the carbon membrane. The concentrated organic is then swept through the membrane via the bulk flow of water in a modality known as “sorp-vection.” We highlight via simplified nonequilibrium thermodynamic models that this “uphill” chemical potential permeation of the organic does not result in second-law violations and can be deduced via measurements of the organic and water sorption and diffusion rates into the carbon membrane. Moreover, this work identifies the need to consider such nonidealities when incorporating unique, rigid materials for the separations of aqueous waste streams.
Guided by thermodynamic modeling, engineering phase transformation pathways via thermo-mechanical processing, in a complex concentrated alloy/high entropy alloy (HEA) of composition Al 0.3 CoFeNi, lead to a novel multi-scale microstructure consisting of fine-scale FCC + L1 2 grains mixed with B2 + BCC grains. The two-step pathway comprises initial decomposition of the parent single-phase FCC to form a fine-grained FCC + B2 microstructure, which further decomposes in the second step into the complex four-phase mixture, exhibiting an excellent combination of tensile yield stress of ~1490 MPa, ultimate tensile strength of ~1663 MPa, with a good ductility of ~12% at room temperature. This paper reports a novel multi-phase microstructure in a HEA/CCA similar to the microstructure observed in dual-phase stainless steel. This report exemplifies the novelty of HEA/CCA compositional space.
A primary goal of molecular physiology is to understand how conformational changes of proteins affect the function of cells, tissues, and organisms. Here, we describe an imaging method for measuring the conformational changes of the voltage sensors of endogenous ion channel proteins within live tissue, without genetic modification. We synthesized GxTX-594, a variant of the peptidyl tarantula toxin guangxitoxin-1E, conjugated to a fluorophore optimal for two-photon excitation imaging through light-scattering tissue. We term this tool EVAP (Endogenous Voltage-sensor Activity Probe). GxTX-594 targets the voltage sensors of Kv2 proteins, which form potassium channels and plasma membrane–endoplasmic reticulum junctions. GxTX-594 dynamically labels Kv2 proteins on cell surfaces in response to voltage stimulation. To interpret dynamic changes in fluorescence intensity, we developed a statistical thermodynamic model that relates the conformational changes of Kv2 voltage sensors to degree of labeling. We used two-photon excitation imaging of rat brain slices to image Kv2 proteins in neurons. We found puncta of GxTX-594 on hippocampal CA1 neurons that responded to voltage stimulation and retain a voltage response roughly similar to heterologously expressed Kv2.1 protein. Our findings show that EVAP imaging methods enable the identification of conformational changes of endogenous Kv2 voltage sensors in tissue.
Abstract We study the effect of degenerate parametric down-conversion (DPDC) in an ensemble of two-level quantum emitters (QEs) coupled via near-field interactions to a single surface plasmon (SP) mode of a nonlinear plasmonic cavity. For this purpose, we develop a quantum driven-dissipative model capturing non-equilibrium dynamics of the system in which incoherently pumped QEs have transition frequency tuned near the second-harmonic response of the SPs. Considering the strong coupling regime, i.e. the SP-QE interaction rate exceeds system dissipation rates, we find a critical SP-QE coupling attributed to the phase transition between normal and lasing steady states. Examining fluctuations above the system’s steady states, we predict new elementary excitations, namely, the exciton-plasmon polaritons formed by the two-SP quanta and single-exciton states of QEs. The contribution of two-SP quanta results in the linear scaling of the SP-QE interaction rate with the number of QEs, o , as opposed to the o -scaling known for the Dicke and Tavis–Cummings models. We further examine how SP-QE interaction scaling affects the polariton dispersions and power spectra in the vicinity of the critical coupling. For this purpose, we compare the calculation results assuming a finite ensemble of QEs and the model thermodynamic limit. The calculated power spectra predict an interplay of coherent photon emission by QEs near the second-harmonic frequency and correlated photon-pair emission at the fundamental frequency by the SPs (i.e. the photonic DPDC effect).
Askival is a light-toned, coarsely crystalline float rock, which was identified near the base of Vera Rubin Ridge in Gale crater. We have studied Askival, principally with the ChemCam instrument but also using APXS compositional data and MAHLI images. Askival and an earlier identified sample, Bindi, represent two rare examples of feldspathic cumulate float rocks in Gale crater with >65% relict plagioclase. Bindi appears unaltered whereas Askival shows textural and compositional signatures of silicification, along with alkali remobilization and hydration. Askival likely experienced multiple stages of alteration, occurring first through acidic hydrolysis of metal cations, followed by deposition of silica and possible phyllosilicates at low T and neutral-alkaline pH. Through laser-induced breakdown spectroscopy compositional analyses and normative calculations, we suggest that an assemblage of Fe-Mg silicates including amphibole and pyroxene, Fe phases, and possibly Mg-rich phyllosilicate are present. Thermodynamic modeling of the more pristine Bindi composition predicts that amphibole and feldspar are stable within an upper crustal setting. This is consistent with the presence of amphibole in the parent igneous rocks of Askival and suggests that the paucity of amphiboles in other known Martian samples reflects the lack of representative samples of the Martian crust rather than their absence on Mars.
Ejector-driven systems have the ability to operate at high efficiencies, utilizing recycled thermal energy as a power source. For a typical ejector heat pump (EHP) system, the increase of the condenser temperature reduces the coefficient of performance (COP). In addition, if the condenser temperature is higher than the critical temperature, the ejector may not function. In this situation, the condenser temperature must be reduced, and an additional heater will be utilized to heat the production water from the condenser temperature to the desired temperature. In this study, a single-stage gas-fired EHP is investigated and thermodynamically modeled to optimize the system COP for the purpose of heating water by utilizing the thermal energy from the ambient air. The effects of the high-temperature evaporator (HTE) and low-temperature evaporator (LTE) on the ejector critical back pressure and the EHP system performance are examined for a HTE temperature range of 120–180 °C and LTE temperatures of 15.5, 17.5, and 19.5 °C. Our results show that an optimized COP for the EHP system exists and is dependent on HTE and LTE temperatures and the primary nozzle throat diameter. In addition, it is found that the peak EHP COP does not necessarily coincide with a large ejector COP. From this study, a maximum EHP COP of 1.31 is achieved at a HTE temperature of 170 °C and LTE temperature of 19.5 °C with a total heating capacity of 15.98 kW.
Abstract Ni- and Co-based M–Cr–Al–Y (M = Ni and/or Co), dual phase β and γ/γ′, β—Ni–Al, γ—Ni(Co, Cr), and γ′—Ni3–Al superalloys exhibit several beneficial high-temperature (>1000 °C) (2012 °F) strength and corrosion resistance properties. Our study investigates the feasibility of fabricating a commercially available Ni–Co–Cr–AlY alloy (tradename “Amdry 386”) using laser directed energy deposition (laser-DED). A significant challenge for laser fabrication of bulk Amdry 386 (A386) structures stems from the presence of relatively higher amounts of the β phase than γ/γ′ phases. While prior studies report laser fabrication of these materials in coating and cladding configurations, bulk structures have not been realized. To investigate these challenges, this study was developed to systematically evaluate the effects of modifying the A386 alloy by adding 10, 20, and 30% by weight of a Ni–20%Cr (Ni–Cr) alloy (mainly γ/γ′). Laser-DED-fabricated A386 coupons exhibited a metastable, rapidly solidified β-rich microstructure typical to laser processes. The A386 + Ni–Cr mixtures were processed using laser-DED, and small coupons from each composition were evaluated using SEM, XRD, and microhardness to characterize the as-processed microstructure. Thermodynamic modeling was performed to determine the phase evolution as a function of the alloy composition. The dominating phase switches from β to γ/γ’ between the A386 and A386 + 10% Ni–Cr mixtures, but the increase in structural integrity is not observed until the Ni–Cr additions reach a minimum of 20%. Our results show that the alloy chemistry can be successfully modified to improve the structural integrity of laser-processed structures.
Ejector driven systems have the ability to operate at high efficiencies, utilizing recycled thermal energy as a power source. For a typical ejector heat pump system, the increase of the condenser temperature reduces the coefficient of performance (COP). In addition, if the condenser temperature is higher than the critical temperature, the ejector may not function. In this situation, the condenser temperature must be reduced, and an additional heater will be utilized to heat the production water from the condenser temperature to the desired temperature. In this investigation, a single-stage gas-fired ejector heat pump (EHP) is investigated and thermodynamically modeled in order to optimize the system COP for the purpose of heating water by utilizing the thermal energy from the ambient air. The effects of the high-temperature evaporator (HTE) and low-temperature evaporator (LTE) temperatures on the ejector critical back pressure and the EHP system performance are examined for a HTE temperature range of 120–180 °C and LTE temperatures of 15.5, 17.5, and 19.5 °C. Results show that an optimized COP of the EHP system exists which depends on HTE and LTE temperatures, primary nozzle throat diameters. In addition, it is found that the EHP COP is independent of the ejector COP. From this investigation a maximum EHP COP of 1.31 is able to be achieved for a HTE temperature of 160 °C and a LTE temperature of 19.5 °C with a total heat capacity of 15.98 kW.
Equilibrium condensation of solar gas is often invoked to explain the abundance of refractory elements in planets and meteorites. This is partly motivated, by the observation that the depletions in both the least and most refractory rare earth elements (REEs) in meteoritic group II calcium-aluminum–rich inclusions (CAIs) can be reproduced by thermodynamic models of solar nebula condensation. We measured the isotopic compositions of Ce, Nd, Sm, Eu, Gd, Dy, Er, and Yb in eight CAIs to test this scenario. Contrary to expectation for equilibrium condensation, we find light isotope enrichment for the most refractory REEs and more subdued isotopic variations for the least refractory REEs. This suggests that group II CAIs formed by a two-stage process involving fast evaporation of preexisting materials, followed by near-equilibrium recondensation. The calculated time scales are consistent with heating in events akin to FU Orionis– or EX Lupi–type outbursts of eruptive pre–main-sequence stars.
The production of precious metals from Cu-rich sources such as ore products or secondary sources is slow and complex largely due to limited solubility in aqueous electrolytes. This results in sequential processing with various electrolytes and chemistries, where first Cu is electrorefined, followed by Ag, followed by Au and the platinum group metals. These are separate processes, often conducted in separate electrorefining and electrowinning facilities. The chemical properties of molten sulfides, and their ability to operate at a temperature where liquid metal cathodes are used, suggest the possibility of an alternative, streamlined processing route for Cu and precious metals. Unfortunately, little thermodynamic or electrochemical information is available regarding the behavior of Cu and precious metal sulfides in molten sulfide electrolytes. Herein, the relative activity of the Cu 2 S-Ag 2 S pseudobinary dissolved in a BaS-La 2 S 3 supporting electrolyte is measured at 1523 K. It was found that the supporting electrolyte favors mixing with Ag 2 S over Cu 2 S. Molten sulfide electrolysis of Cu and Ag was conducted, with results in good agreement with the thermodynamic model. It is found that the Ag-Cu cathode chemistry will influence the electrochemical selectivity in the Ag-Cu-Ba-La-S system.
Uranyl ion, UO 2 2+ , and its aqueous complexes with organic and inorganic ligands can be the dominant species for uranium transport on the Earth surface or in a nuclear waste disposal system if an oxidizing condition is present. As an important biodegradation product, oxalate, C 2 O 4 2– , is ubiquitous in natural environments and is known for its ability to complex with the uranyl ion. Oxalate can also form solid phases with uranyl ion in certain environments thus limiting uranium migration. Therefore, the determination of stability constants for aqueous and solid uranyl oxalate complexes is important not only to the understanding of uranium mobility in natural environments, but also to the performance assessment of nuclear waste disposal. In this work, we developed a thermodynamic model for the UO 2 2+ –Na + –H + –Cl – –ClO 4 – –C 2 O 4 2– –NO 3 – –H 2 O system to ionic strength up to ~11 mol•kg –1 . We constrained the stability constants for UO 2 C 2 O 4 (aq) and UO 2 (C 2 O 4 ) 2 2– at infinite dilution based on our evaluation of the literature data over a wide range of ionic strengths up to ~11 mol•kg –1 . We also obtained the solubility constants at infinite dilution for solid uranyl oxalates, UO 2 C 2 O 4 •3H 2 O, based on the solubility data over a wide range of ionic strengths. The developed model will enable for the accurate stability assessment of oxalate complexes affecting uranium mobility under a wide range of conditions including those in deep geological repositories.
This progress report (Level 4 Milestone Number M4SF-20LL010301042) summarizes research conducted at Lawrence Livermore National Laboratory (LLNL) within the Argillite Activity Number SF-20LL010301041. LLNL is leading efforts in the development of thermodynamic databases in support of the Spent Fuel and Waste Science Technology (SFWST) program. Thermodynamic models provide the basis for understanding the stability of solid phases and speciation of aqueous species and modeling the evolution of repository conditions. The LLNL effort is being performed in coordination with other US database development efforts. The effort includes a review of available thermochemical databases and a path forward for database integration. International coordination with the NEA-TDB is supported through crystalline international work package.
Given the steady growth in world population and the ever-increasing fresh water demand, the only sustainable water supply option is desalination. Conceptually, desalination is very simple - just separate dissolved salts from water. While desalination research programs have existed since the 1960s and have resulted in a multitude of approaches, realizing affordable desalination has proven to be a challenge. Our goal is to meet this challenge using low cost heat sources to drive a liquid-discharge-free desalination process that can be co-mingled with the extraction of economically valuable co-products. High temperatures and pressures will be used to manipulate water’s properties, such as the dielectric constant, and hence its ability to solvate ions. Selective precipitation/recovery of valuable metal co-products creates new revenue streams (i.e., cost offsets). We will develop the scientific understanding necessary to control salt precipitation from supercritical seawater, inland brines, and water commonly co-produced with oil and gas. Atomistic simulations will be used to understand at a molecular level the changes in hydrogen bonding and ion solvation that occur as we increase the temperature and/or pressure and change the density and ion concentration. Our simulation results will also aid in the interpretation of experimental data and guide the development of applied thermodynamic models for engineering design calculations.
This is the final technical report for the DOE MURI project on developing high-operating temperature heat transfer fluids for solar thermal power generation. This project aimed to evaluate liquid metals as a heat-transport fluid and potential energy storage medium for concentrated solar powered (CSP) systems. The project consisted of five phases, starting with fluid selection and screen and ending with potential CSP integration. The initial fluid selection arrived at heavy liquid metals as candidate fluids such as lead bismuth eutectic (LBE) as the prime liquid-alloy candidate to be studied, given the conditions above. Fifty-seven liquid compositions were initially identified with liquidus temperatures lower than 200°C, composed of elements that provide no driving force to the reduction of Cr 2 O 3 or Al 2 O 3 passivation layers in pipe material which is required for corrosion prevention. LBE was identified as the primary candidate fluid after these compositions were compared against computational thermodynamic modeling to screen all of the selected systems that would be compatible with our design objectives. Twenty-eight of these compositions were also investigated with the rapid characterization methods; the accuracies of the liquidus temperature and the specific heats predicted by the computations were better than 3 percent and 9 percent, respectively. We conducted numerus corrosion tests of various Fe-Cr-Al based steels in LBE and its variants at temperate as high as 800°C. It was found that minor additions to the liquid did not provide sufficient corrosion protection to warrant their use in real applications. Furthermore, we investigated the detailed mechanism of corrosion between heavy liquid metal and the pipe material at these very high temperatures. A liquid metal loop was constructed to operate at these high temperatures. The loop construction and operation lead to valuable lessons learned that will be needed for industrial scale loops. Furthermore, we learned that electromagnetic pumps at these extreme temperatures will have to be reengineered and redesigned to be used for CSP applications.
Thermochemical and thermophysical properties of several molten salt systems of interest to molten salt reactor (MSR) developers are being measured at Argonne National Laboratory. These properties are needed by developers to design, license, and operate their reactors. Thermochemical properties being measured at Argonne include thermal transitions, phase behavior, and heat capacity. Thermophysical properties being measured at Argonne include liquid density, surface tension, volumetric thermal expansion of the liquid phase, thermal diffusivity, thermal conductivity, and viscosity. Properties of the ternary NaCl-KCl-UCl 3 system that may be used as a fuel bearing salt are being measured. Low-melting eutectic salt compositions are of interest to developers owing to the thermal efficiency. Using salts with low melting temperatures allow reactors to be operated at a lower temperature to improve operation and decrease safety concerns. Confirming low melting behaviors are maintained during composition changes that occur during fission is also an important factor. It is essential to any molten salt reactor developer utilizing a fuel bearing salt to have a complete understanding of the behavior of that fuel salt at a variety of compositions near the eutectic composition they plan to use. This kind of stability is indicated on a phase diagram by low liquidus slopes at compositions bordering the eutectic. Therefore, a thermodynamic model was constructed to determine what compositions of the ternary NaCl, KCl, and UCl 3 system should be studied to support MSR developers.