The 16-foot transonic tunnel laser velocimeter system
The Langley 16-foot transonic wind tunnel is described. The system configuration, optical layout, laser color separator, optical receiver, and tunnel window are discussed.
Franke, J. M.↗
SEARCH · Search NASA
Results for “Transonic wind tunnel”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Evaluation of moire techniques for wind tunnel metrology
The development of a moire technique suitable for the analysis of object deflections in a cryogenically cooled, transonic wind tunnel is described. The operating environment for the wind tunnel has a temperature range of 77 to 3390 k, pressure to 91390 Kgs/sq m, and noise to 150 dB SPL. Efforts were made to accomplish the following: to demonstrate projection moire as it would be used to study structural deflections; to use optical processing to multiply the sensitivity of the moire; and to investigate a system design based on the requirements of the wind tunnel geometry.
Harris, J. S.↗
Aerodynamic characteristics from mach 0.22 to 4.65 of a two-stage rocket vehicle having an unusual nose shape high power, high voltage, audio frequency transformer design manual final report, 1 jul. 1962 - 31 aug. 1964
Transonic and supersonic aerodynamic characteristics for two-stage rocket vehicle with blunted nose cone on square body with conical flare termination
ROCKET VEHICLE↗
Investigation of the interference effects of mixed flow long duct nacelles on a DC-10 wing
Wind tunnel test results utilizing a 4.7 percent scale semispan model in the 11 foot transonic wind tunnel are presented. A low drag long duct nacelle installation for the DC-10 jet transport was developed. A long duct nacelle representative of a CF6-50 mixed flow configuration was investigated on the DC-10-30. The results showed that the long duct nacelle installation located in the same position as the current short duct nacelle and with the current production symmetrical pylon is a relatively low risk installation for the DC-10 aircraft. Tuft observations and analytical boundary layer analysis confirmed that the flow on the nacelle afterbody was attached. A small pylon fairing was evaluated and found to reduce channel peak suction pressures, which resulted in a small drag improvement. The test also confirmed that the optimum nacelle incidence angle is the same as for the short duct nacelle, thus the same engine mount as for the production short duct nacelle can be used for the long duct nacelle installation. Comparison of the inboard wing pylon nacelle channel pressure distributions, with flow through and powered long duct nacelles showed that the power effects did not change the flow mechanism; hence, power effects can be considered negligible.
Patel, S. P.↗
Influence of Strain-Gage Balance Characteristics on the Precision Error of the Drag Coefficient
Improvements and results of a new method are presented that computes a pre-test estimate of the precision error of the drag coefficient of a wind tunnel model. The error estimate is defined as the part of the drag coefficient's precision error that is primarily associated with the precision error of the angle of attack measurement and physical characteristics of the chosen strain-gage balance. The method indirectly describes the precision error of the angle of attack measurement by using an assumed balance gage output variation of one microV/V. The physical characteristics of the balance, on the other hand, are described by partial derivatives of the axial and normal forces with respect to the strain-gage outputs. These derivatives can directly be obtained from the data reduction matrix of the balance. The precision error estimate itself is calculated by applying a simple explicit equation that uses the model reference area, the dynamic pressure, the angle of attack, the coefficients of the linear terms of the data reduction matrix, and the electrical output variation of one microvolt per volt as input. Precision errors at constant angle of attack may be visualized as contour plots by plotting them, for example, versus the Mach number and the total pressure. Characteristics of NASA's MC60E balance are used in combination with the reference area of a generic wind tunnel model in order to demonstrate that error estimates are independent of both the balance load format and the units chosen for the description of balance loads, model reference area, and the dynamic pressure. Finally, experimental data from a wind tunnel test of the Ames Check Standard Model in the NASA Ames 11-foot Transonic Wind Tunnel illustrates the application of the method to real-world test data.
precision error↗
Improved Correction System for Vibration Sensitive Inertial Angle of Attack Measurement Devices
Inertial angle of attack (AoA) devices currently in use at NASA Langley Research Center (LaRC) are subject to inaccuracies due to centrifugal accelerations caused by model dynamics, also known as sting whip. Recent literature suggests that these errors can be as high as 0.25 deg. With the current AoA accuracy target at LaRC being 0.01 deg., there is a dire need for improvement. With other errors in the inertial system (temperature, rectification, resolution, etc.) having been reduced to acceptable levels, a system is currently being developed at LaRC to measure and correct for the sting-whip-induced errors. By using miniaturized piezoelectric accelerometers and magnetohydrodynamic rate sensors, not only can the total centrifugal acceleration be measured, but yaw and pitch dynamics in the tunnel can also be characterized. These corrections can be used to determine a tunnel's past performance and can also indicate where efforts need to be concentrated to reduce these dynamics. Included in this paper are data on individual sensors, laboratory testing techniques, package evaluation, and wind tunnel test results on a High Speed Research (HSR) model in the Langley 16-Foot Transonic Wind Tunnel.
Crawford, Bradley L.↗
An exploratory wind-tunnel investigation of the wake effect of a panel tip-mounted fan-jet engine on the lift-induced vortex
Transonic wind tunnel tests to determine wake effect of tip-mounted fan-jet engine on reducing tip vorticity of unswept symmetrical panel
Flechner, S. G.↗
Wind tunnel wall interference effects on a supercritical airfoil at transonic speeds
Wind tunnel tests of a 10% supercritical airfoil have been conducted in the Lockheed Compressible Flow Facility at transonic speeds to determine the effects of varying wind tunnel wall porosity on airfoil performance. Wall configurations ranging in porosity from 1.3% to 10% were investigated at Reynolds numbers of 7 to 30 million. Experimental data presented to show the effect of varying wall porosity include airfoil surface pressures, airfoil forces, and wind tunnel wall pressures. Utilizing the experimental results, an assessment of the applicability of current subcritical theoretical methods to predict wall interference corrections in subsonic and transonic flows is made.
Blackwell, J. A., Jr.↗
Aerodynamic coefficient estimation for dynamic wind tunnel models
Maximum likelihood parameter identification is used to estimate the aerodynamic coefficients of a 'flying' aircraft model which is mounted in a transonic wind tunnel by a system of cables and pulleys. The model's motion is governed by both cable and aerodynamic forces, where the parameters to be identified are functions of the aerodynamic forces but cable forces greatly predominate. The test data were successfully processed assuming a linear equation model in the identification procedure. In one instance, the procedure was able to detect a failing measurement instrument. The final parameter estimates are compared to estimates obtained in independent tests of a similar aircraft model.
Mohr, R. L.↗
Wind tunnel tests of an F-8 airplane model equipped with an oblique wing
An experimental investigation was conducted in an 11- by 11-foot transonic wind tunnel to study the lift, drag and stability characteristics of a 0.087-scale model of an operational airplane fitted with an oblique wing. The model wing was of elliptical planform with an unswept aspect ratio of 12.7 and a thickness of 10 percent. All other external geometric features of the model were scaled to the basic full size operational airplane with the engine inlet faired closed. Longitudinal and lateral-directional stability data were obtained with the wing at sweep angles of 0 deg, 45 deg and 60 deg Test Mach numbers ranged from 0.6 to 1.4 deg Angles of attack were between minus 4 deg and 8 deg at zero sideslip. Angles of sideslip were between plus and minus 4 degrees for two angles of attack depending upon the wing configuration. Tests were conducted at a Reynolds number of 6 million per foot except for a few runs when balance capacity limited the Reynolds number to 4 million per foot.
Graham, L. A.↗
Comparison of Force and Moment Coefficients for the Same Test Article in Multiple Wind Tunnels
This paper compares the results of force and moment measurements made on the same test article and with the same balance in three transonic wind tunnels. Comparisons are made for the same combination of Reynolds number, Mach number, sideslip angle, control surface configuration, and angle of attack range. Between-tunnel force and moment differences are quantified. An analysis of variance was performed at four unique sites in the design space to assess the statistical significance of between-tunnel variation and any interaction with angle of attack. Tunnel to tunnel differences too large to attribute to random error were detected were observed for all forces and moments. In some cases these differences were independent of angle of attack and in other cases they changed with angle of attack.
Deloach, Richard↗
Improved Aerodynamic Analysis for Hybrid Wing Body Conceptual Design Optimization
This paper provides an overview of ongoing efforts to develop, evaluate, and validate different tools for improved aerodynamic modeling and systems analysis of Hybrid Wing Body (HWB) aircraft configurations. Results are being presented for the evaluation of different aerodynamic tools including panel methods, enhanced panel methods with viscous drag prediction, and computational fluid dynamics. Emphasis is placed on proper prediction of aerodynamic loads for structural sizing as well as viscous drag prediction to develop drag polars for HWB conceptual design optimization. Data from transonic wind tunnel tests at the Arnold Engineering Development Center s 16-Foot Transonic Tunnel was used as a reference data set in order to evaluate the accuracy of the aerodynamic tools. Triangularized surface data and Vehicle Sketch Pad (VSP) models of an X-48B 2% scale wind tunnel model were used to generate input and model files for the different analysis tools. In support of ongoing HWB scaling studies within the NASA Environmentally Responsible Aviation (ERA) program, an improved finite element based structural analysis and weight estimation tool for HWB center bodies is currently under development. Aerodynamic results from these analyses are used to provide additional aerodynamic validation data.
Gern, Frank H.↗
A critical assessment of UH-60 main rotor blade airfoil data
Many current comprehensive rotorcraft analyses employ lifting-line methods that require main rotor blade airfoil data, typically obtained from wind tunnel tests. In order to effectively evaluate these lifting-line methods, it is of the utmost importance to ensure that the airfoil section data are free of inaccuracies. A critical assessment of the SC1095 and SC1094R8 airfoil data used on the UH-60 main rotor blade was performed for that reason. Nine sources of wind tunnel data were examined, all of which contain SC1095 data and four of which also contain SC1094R8 data. Findings indicate that the most accurate data were generated in 1982 at the 11-Foot Wind Tunnel Facility at NASA Ames Research Center and in 1985 at the 6-inch by 22-inch transonic wind tunnel facility at Ohio State University. It has not been determined if data from these two sources are sufficiently accurate for their use in comprehensive rotorcraft analytical models of the UH-60. It is recommended that new airfoil tables be created for both airfoils using the existing data. Additional wind tunnel experimentation is also recommended to provide high quality data for correlation with these new airfoil tables.
Totah, Joseph↗
Hot-film system for transition detection in cryogenic wind tunnels
It is well known that the determination of the location of boundary-layer transition is necessary for the correct interpretation of aerodynamic data in transonic wind tunnels. In the late 1970s the Douglas Aircraft Company developed a vapor deposition hot-film system for transition detection in cryogenic wind tunnels. Tests of the hot-films in a low-speed tunnel demonstrated the ability to obtain on-line transition data with an enhanced simultaneous hot-film data acquisition system. The equipment design and specifications are described.
Johnson, Charles B.↗
Investigation to optimize the passive shock wave/boundary layer control for supercritical airfoil drag reduction
The passive shock wave/boundary layer control for reducing the drag of 14%-thick supercritical airfoil was investigated in the 3 in. x 15.4 in. RPI Transonic Wind Tunnel with and without the top wall insert at transonic Mach numbers. Top wall insert was installed to increase the flow Mach number to 0.90 with the model mounted on the test section bottom wall. Various porous surfaces with a cavity underneath were positioned on the area of the airfoil where the shock wave occurs. The higher pressure behind the shock wave circulates flow through the cavity to the lower pressure ahead of the shock wave. The effects from this circulation prevent boundary layer separation and enthropy increase hrough the shock wave. The static pressure distributions over the airfoil, the wake impact pressure survey for determining the profile drag and the Schlieren photographs for porous surfaces are presented and compared with the results for solid surface airfoil. With a 2.8% uniform porosity the normal shock wave for the solid surface was changed to a lambda shock wave, and the wake impact pressure data indicate a drag coefficient reduction as much as 45% lower than for the solid surface airfoil at high transonic Mach numbers.
Nagamatsu, H. T.↗
A critical assessment of UH-60 main rotor blade airfoil data
Many current comprehensive rotorcraft analyses employ lifting-line methods that require main rotor blade airfoil data, typically obtained from wind tunnel tests. In order to effectively evaluate these lifting-line methods, it is of the utmost importance to ensure that the airfoil section data are free of inaccuracies. A critical assessment of the SC1095 and SC1094R8 airfoil data used on the UH-60 main rotor blade was performed for that reason. Nine sources of wind tunnel data were examined, all of which contain SC1095 data and four of which also contain SC1094R8 data. Findings indicate that the most accurate data were generated in 1982 at the 11-Foot Wind Tunnel Facility at NASA Ames Research Center and in 1985 at the 6-inch-by-22-inch transonic wind tunnel facility at Ohio State University. It has not been determined if data from these two sources are sufficiently accurate for their use in comprehensive rotorcraft analytical models of the UH-60. It is recommended that new airfoil tables be created for both airfoils using the existing data. Additional wind tunnel experimentation is also recommended to provide high quality data for correlation with these new airfoil tables.
Totah, Joseph↗
Remote detection of boundary-layer transition by an optical system
This instrument development program was funded because of the urgent need to measure boundary-layer transition in wind tunnels. In the course of this development program, a prototype was designed, built, and tested. Recent transonic experiments in the Boeing Model Transonic Wind Tunnel show that the interferometer results correlate very well with sublimating chemical tests.
Hall, Robert M.↗
Investigation of minimum operating temperatures for cryogenic wind tunnels
Total temperatures corresponding to the onset of condensation effects were determined for flow over a 0.137-m NACA 0012-64 airfoil mounted in the Langley 1/3-m transonic wind tunnel. Tests were carried out at a total pressure range from 1.2 to 4.5 atm and at free-stream Mach numbers of 0.75, 0.85, and 0.95. No condensation effects were found to occur until total temperatures were below those associated with free-stream saturation. Significant increases in Reynolds number may apparently be obtained by operation at wind tunnel temperatures below those associated with local saturation over the airfoil but above those where effects first occur. For the 0.85 and 0.95 Mach numbers the increase in Reynolds number was at least 15% over those achieved at local saturation conditions for the same pressure range. Higher pressures may have had some detrimental effect in the 0.95 Mach number test.
Hall, R. M.↗