Search NASA⌕ Search

SEARCH · Search NASA

Results for “Wind Speed”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Results of an aerodynamic investigation of a space shuttle orbiter/747 carrier flight test configuration to determine separation characteristics utilizing 0.0125-scale models (48-0/AX1318I-1) in the LTV 4 x 4 foot high speed wind tunnel (CA26), volume 1

Results of tests conducted on a 0.0125-scale model of the Space Shuttle Orbiter and a 0.0125-scale model of the 747 CAM configuration in a 4 x 4-foot High Speed Wind Tunnel were presented. Force and moment data were obtained for each vehicle separately at a Mach number of 0.6 and for each vehicle in proximity to the other at Mach numbers of 0.3, 0.5, 0.6 and 0.7. The proximity effects of each vehicle on the other at separation distances (from the mated configuration) ranging from 1.5 feet to 75 feet were presented; 747 Carrier angles of attack from 0 deg to 6 deg and angles of sideslip of 0 deg and -5 deg were tested. Model variables included orbiter elevon, aileron and body flap deflections, orbiter tailcone on and off, and 747 stabilizer and rudder deflections.

Gillins, R. L.↗
NASA NTRS1990

Hot gas ingestion test results of a two-poster vectored thrust concept with flow visualization in the NASA Lewis 9- x 15-foot low speed wind tunnel

A 9.2 percent scale Short Takeoff and Vertical Landing (STOVL) hot gas ingestion model was designed and built by McDonnell Douglas Corporation (MCAIR) and tested in the Lewis Research Center 9 x 15 foot Low Speed Wind Tunnel (LSWT). Hot gas ingestion, the entrainment of heated engine exhaust into the inlet flow field, is a key development issure for advanced short takeoff and vertical landing aircraft. Flow visualization from the Phase 1 test program, which evaluated the hot ingestion phenomena and control techniques, is covered. The Phase 2 test program evaluated the hot gas ingestion phenomena at higher temperatures and used a laser sheet to investigate the flow field. Hot gas ingestion levels were measured for the several forward nozzle splay configurations and with flow control/life improvement devices (LIDs) which reduced the hot gas ingestion. The model support system had four degrees of freedom - pitch, roll, yaw, and vertical height variation. The model support system also provided heated high-pressure air for nozzle flow and a suction system exhaust for inlet flow. The test was conducted at full scale nozzle pressure ratios and inlet Mach numbers. Test and data analysis results from Phase 2 and flow visualization from both Phase 1 and 2 are documented. A description of the model and facility modifications is also provided. Headwind velocity was varied from 10 to 23 kn. Results are presented over a range of nozzle pressure ratios at a 10 kn headwind velocity. The Phase 2 program was conducted at exhaust nozzle temperatures up to 1460 R and utilized a sheet laser system for flow visualization of the model flow field in and out of ground effects. The results reported are for nozzle exhaust temperatures up to 1160 R. These results will contain the compressor face pressure and temperature distortions, the total pressure recovery, the inlet temperature rise, and the environmental effects of the hot gas. The environmental effects include the ground plane contours, the model airframe heating, and the location of the ground flow separation.

Johns, Albert L.↗
NASA NTRS2019

Flow Quality Survey of the 9- by 15-Foot Low Speed Wind Tunnel (2015 and 2016 Tests) Prior to Acoustic Improvement Modifications

A flow quality survey (FQS) was conducted in December 2015 and January 2016 to characterize the flow quality of the 9- by 15-Foot Low-Speed Wind Tunnel (9×15 LSWT) test section prior to the start of significant structural and acoustic modifications. The data from this FQS will be compared with data collected during a replicated FQS after completion of the acoustic improvement modifications. This document contains only the FQS data collected in December 2015 and January 2016 using the 15-ft survey rake and the 18-in. boundary layer rakes in the 9×15 LSWT. The spatial variation at one axial test section station (TSTA), nominally TSTA 198, and five vertical heights of the 15-ft survey rake was computed for Mach number, velocity, total and static pressure, total temperature, and flow angularity (pitch and yaw). Three hot-wire probes mounted to the 15-ft survey rake were used to measure turbulence intensity; however, data from a previous test entry were used as the mean turbulence intensity baseline value, as there were issues with the hot-wire performance. The boundary layer pressure profiles around the perimeter of the test section at TSTA 199 were also measured and the boundary layer heights computed. All calculated results are tabulated for each facility condition set point.

Johnson, Aaron M.↗
NASA NTRS2020

9- by 15-Foot Low-Speed Wind Tunnel Acoustic Free-Field Evaluation After Renovation Part 1: Test Report Summary Part 2: Anechoic Environment Characterization: Field Test Report

This report describes test results from an assessment of the acoustically treated 9- by 15-Foot Low Speed Wind Tunnel at the NASA Glenn Research Center in Cleveland, Ohio in June of 2019. The tests were conducted in accordance with the recently adopted international standard ISO 26101-2012 on Qualification of Free Field Test Environments. This method involves moving a microphone relative to a source and comparing the sound pressure level versus distance measurements with theoretical inverse square law spreading.

wind tunnel↗
NASA NTRS1982

A statistical examination of Nimbus 7 SMMR data and remote sensing of sea surface temperature, liquid water content in the atmosphere and surfaces wind speed

Nimbus 7 Scanning Multichannel Microwave Radiometer (SMMR) brightness temperature measurements over the global oceans have been examined with the help of statistical and empirical techniques. Such analyses show that zonal averages of brightness temperature measured by SMMR, over the oceans, on a large scale are primarily influenced by the water vapor in the atmosphere. Liquid water in the clouds and rain, which has a much smaller spatial and temporal scale, contributes substantially to the variability of the SMMR measurements within the latitudinal zones. The surface wind not only increases the surface emissivity but through its interactions with the atmosphere produces correlations, in the SMMR brightness temperature data, that have significant meteorological implications. It is found that a simple meteorological model can explain the general characteristics of the SMMR data. With the help of this model methods to infer over the global oceans, the surface temperature, liquid water content in the atmosphere, and surface wind speed are developed. Monthly mean estimates of the sea surface temperature and surface winds are compared with the ship measurements. Estimates of liquid water content in the atmosphere are consistent with earlier satellite measurements.

Prabhakara, C.↗
NASA NTRS1983

A statistical examination of Nimbus-7 SMMR data and remote sensing of sea surface temperature, liquid water content in the atmosphere and surface wind speed

Nimbus 7 Scanning Multichannel Microwave Radiometer (SMMR) brightness temperature measurements over the global oceans have been examined with the help of statistical and empirical techniques. Such analyses show that zonal averages of brightness temperature measured by SMMR over the oceans on a large scale are primarily influenced by the water vapor in the atmosphere. Liquid water in the clouds and rain, which has a much smaller spatial and temporal scale, contributes substantially to the variability of the SMMR measurements within the latitudinal zones. The surface wind not only increases the surface emissivity, but through its interactions with the atmosphere produces correlations in the SMMR brightness temperature data that have significant meteorological implications. It is found that a simple meteorological model can explain the general characteristics of the SMMR data. With the help of this model, methods to infer over the global oceans, the surface temperature, liquid water content in the atmosphere, and surface wind speed are developed. Monthly mean estimates of the sea surface temperature and surface winds are compared with the ship measurements. Estimates of liquid water content in the atmosphere are consistent with earlier satellite measurements. Previously announced in STAR as N83-19187

Prabhakara, C.↗
NASA NTRS1974

Continued investigations in the NAAL low speed wind tunnel into the effects of the air breathing propulsion system on orbiter subsonic stability and control characteristics (OA62A)

Experimental aerodynamic investigations were conducted on a stingmounted 0.0405-scale representation (model 43-0) of the 140A/B Space Shuttle Orbiter in a Low Speed Wind Tunnel. The NASA designation for this test was 0A62A. The primary test objective was to continue studies, initiated on tests 0A16 and 0A71A and 0A71C, in optimizing the air breathing propulsion system (ABPS) and investigating the aerodynamic effects of various nacelle number/location configurations on the orbiter stability and control characteristics. Orbiter stability and control characteristics, both with and without ABPS, were investigated at elevon deflections of 0, + or -5, + or -19, + or -5, and -20 deg; aileron deflections of 0 and 10 deg (about 0 deg elevon); and rudder deflections of 0, -7.5, and -15 deg. Aerodynamic force and moment data was measured in the body axis system by a 2.5-inch task type internal balance. The model was sting supported through the base region with a nominal angle of attack range of -4 to 30 deg. Yaw polars were recorded over the beta range of -10 to 10 deg at fixed angles of attack of 0, 5, 10, and 15 deg.

Mennell, R.↗
NASA NTRS1974

Results of low speed wind tunnel tests on a .0405 scale model Rockwell Space Shuttle Orbiter tested both in free air and in the presence of a ground plane (OA16)

Experimental aerodynamic investigations were conducted on a .0405 scale representation of the space shuttle orbiter in a 7.75 x 11 foot low speed wind tunnel during the time period March 21, to April 17, 1973. The primary test objectives were to investigate both the aerodynamic and propulsion effects of various air breathing engine systems in free air and in the presence of the ground. The free air portion of this test investigated the aerodynamic effects of engine nacelle number, nacelle grouping, and nacelle location. For this testing the model was sting mounted on a six component internal strain gage balance entering through the model base. The ground plane portion of the aerodynamic test investigated the same nacelle effects at ground plane locations of full scale W.P. = 239.9, 209.3, 158.9, 108.5, and 7.78 in. At the conclusion of the aerodynamic test period the propulsion effects of various nacelle locations and freestream orientations in the presence of the ground were investigated.

Mennell, R. C.↗
NASA NTRS1989

The annual and interannual variabilities of precipitable water, surface wind speed, and sea surface temperature over the tropical Pacific

The Nimbus-7 Scanning Multichannel Microwave Radiometer (SSMR) provided simultaneous measurements of three geophysical parameters, each of which describing a certain aspect of the evolution of the 1982-1983 ENSO: the sea-surface temperature (T), precipitable water (W), and surface-wind speed (U). In this paper, values derived from the SSMR were compared with in situ measurements from ships, research buoys, and operational island stations in the tropical Pacific between January 1980 and October 1983, demonstrating the temporal and spatial coherence of the SSMR measurements. The results show that the variabilities of the surface convergence, sea surface temperature, and precipitable water are related. It was found that W anomalies were not always colocated with T anomalies, and that W anomalies were often associated with negative U anomalies, interpreted as surface convergence.

Liu, W. Timothy↗
NASA NTRS1999

Wind Speed Measurement from Bistatically Scattered GPS Signals

Instrumentation and retrieval algorithms are described which use the forward, or bistatically scattered range-coded signals from the Global Positioning System (GPS) radio navigation system for the measurement of sea surface roughness. This roughness is known to be related directly to the surface wind speed. Experiments were conducted from aircraft along the TOPEX ground track, and over experimental surface truth buoys. These flights used a receiver capable of recording the cross correlation power in the reflected signal. The shape of this power distribution was then compared against analytical models derived from geometric optics. Two techniques for matching these functions were studied. The first recognized the most significant information content in the reflected signal is contained in the trailing edge slope of the waveform. The second attempted to match the complete shape of the waveform by approximating it as a series expansion and obtaining the nonlinear least squares estimate. Discussion is also presented on anomalies in the receiver operation and their identification and correction.

Garrison, James L.↗
NASA NTRS2006

A Comparison of Wind Speed Data from Mechanical and Ultrasonic Anemometers

This study compared the performance of mechanical and ultrasonic anemometers at the Eastern Range (ER; Kennedy Space Center and Cape Canaveral Air Force Station on Florida's Atlantic coast) and the Western Range (WR; Vandenberg Air Force Base on California's Pacific coast). Launch Weather Officers, forecasters, and Range Safety analysts need to understand the performance of wind sensors at the ER and WR for weather warnings, watches, advisories, special ground processing operations, launch pad exposure forecasts, user Launch Commit Criteria (LCC) forecasts and evaluations, and toxic dispersion support. The current ER and WR weather tower wind instruments are being changed from the current propeller-and-vane (ER) and cup-and-vane (WR) sensors to ultrasonic sensors through the Range Standardization and Automation (RSA) program. The differences between mechanical and ultrasonic techniques have been found to cause differences in the statistics of peak wind speed in previous studies. The 45th Weather Squadron (45 WS) and the 30th Weather Squadron (30 WS) requested the Applied Meteorology Unit (AMU) to compare data between RSA and current sensors to determine if there are significant differences. Approximately 3 weeks of Legacy and RSA wind data from each range were used in the study, archived during May and June 2005. The ER data spanned the full diurnal cycle, while the WR data was confined to 1000-1600 local time. The sample of 1-minute data from numerous levels on 5 different towers on each range totaled more than 500,000 minutes of data (482,979 minutes of data after quality control). The 10 towers were instrumented at several levels, ranging from 12 ft to 492 ft above ground level. The RSA sensors were collocated at the same vertical levels as the present sensors and typically within 15 ft horizontally of each another. Data from a total of 53 RSA ultrasonic sensors, collocated with present sensors were compared. The 1-minute average wind speed/direction and the 1-second peak wind speed/direction were compared.

Short, D.↗
NASA NTRS1973

Low-speed wind tunnel investigation of a semispan STOL jet transport wing body with an upper surface blown jet flap

An investigation of the static longitudinal aerodynamic characteristics of a semispan STOL jet transport wing-body with an upper-surface blown jet flap for lift augmentation was conducted in a low-speed wind tunnel having a 12-ft octagonal test section. The semispan swept wing had an aspect ratio of 3.92 (7.84 for the full span) and had two simulated turbofan engines mounted ahead of and above the wing in a siamese pod equipped with an exhaust deflector. The purpose of the deflector was to spread the engine exhaust into a jet sheet attached to the upper surface of the wing so that it would turn downward over the flap and provide lift augmentation. The wing also had optional boundary-layer control provided by air blowing through a thin slot over a full-span plain trailing-edge flap.

Phelps, A. E., III↗
NASA NTRS1974

The results of a low-speed wind tunnel test to investigate the effects of the Refan JT8D engine target thrust reverser on the stability and control characteristics of the Boeing 727-200 airplane

The effects of the Refan JT8D side engine target thrust reverser on the stability and control characteristics of the Boeing 727-200 airplane were investigated using the Boeing-Vertol 20 x 20 ft Low-Speed Wind Tunnel. A powered model of the 727-200 was tested in groud effect in the landing configuration. The Refan target reverser configuration was evaluated relative to the basic production 727 airplane with its clamshell-deflector door thrust reverser design. The Refan configuration had slightly improved directional control characteristics relative to the basic airplane. Clocking the Refan thrust reversers 20 degrees outboard to direct the reverser flow away from the vertical tail, had little effect on directional control. However, clocking them 20 degrees inboard resulted in a complete loss of rudder effectiveness for speeds greater than 90 knots. Variations in Refan reverser lip/fence geometry had a minor effect on directional control.

Kupcis, E. A.↗
NASA NTRS1976

Low speed wind tunnel investigation of the aerodynamic and acoustic performance of several sonic inlet takeoff and approach geometries

A series of tests was conducted to determine the aerodynamic and acoustic performance of several sonic inlet takeoff and approach geometries. The effects of inlet lip shape and diffuser length were also investigated. The tests were conducted in a low-speed wind tunnel at free-stream velocities of 0 and 45 meters per second. Inlet incidence angle was varied from 0 deg to 50 deg. The inlets were sized to fit a 13.97-centimeter-diameter fan. In terms of the highest level of inlet total pressure recovery for a given amount of noise suppression, a cylindrical centerbody takeoff geometry and a bulb-shaped centerbody approach geometry provided the best results over all conditions of free-stream velocity and incidence angle. Increasing inlet lip contraction ratio extended the maximum incidence angle for attached lip flow, while increasing inlet diffuser length resulted in a higher total pressure recovery for a given amount of noise suppression.

Abbott, J. M.↗
DOE OSTI2023

The Diurnal Cycle of East Pacific Convection, Moisture, and CYGNSS Wind Speed and Fluxes

The far eastern tropical Pacific is one of the rainiest locations on Earth. This region is characterized by a robust diurnal cycle with precipitation initiating over the Andes mountains in Colombia in the late afternoon and moving offshore overnight while organizing into mesoscale convective systems (MCSs). As the MCSs move westward, they can seed tropical easterly waves that develop into tropical cyclones. Novel measurements of near-surface wind speeds and latent heat flux (LHFLX) from the Cyclone Global Navigation Satellite System (CYGNSS) mission and ERA5 reanalysis are used to evaluate changes to regional flow patterns, moisture, and LHFLX that favor a strong westward propagating diurnal cycle of precipitation in this region. Days with strongly versus weakly westward propagating diurnal precipitation are compared during the extended boreal summer of the CYGNSS era (May–October 2018–2021). Strongly propagating days have a more moist lower troposphere with stronger vertically integrated moisture flux convergence than days with weakly propagating precipitation. The enhanced low-level moisture is supported by increased wind-driven LHFLX from stronger regional flows including the Choco and Caribbean Low-Level Jets and Panama and Papagayo gap winds. Increased offshore convergence and vorticity also help sustain convection during the days with strongly propagating precipitation. Background variations in the physical environment, as opposed to diurnal variations, seem more important for supporting a robust diurnal cycle of precipitation in the region.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1985

ROWS estimates of wave height, wind speed, and directional wave spectra for SIR-B underflights off Chile, October 11 and 12, 1984

An account is given of the successful operation of the Goddard Ku-band Radar Ocean Wave Spectrometer (ROWS) on four out of five of the NASA Wallops' P-3 underflights of the Shuttle Imaging Radar-B (SIR-B) off the coast of southern Chile during the period of October 7-12, 1984. ROWS provided surface wind speed, wave height, and directional wave height spectrum estimates from the instrument's nadir altimeter mode and off-nadir spectrometer mode. ROWS estimates of the directional spectra of 300-400-m wavelength swell-dominated 3-5 m seas on October 11 and 12 are presented and compared to SCR (Surface Contour Radar), SIR-B, and Navy GSOWM spectra. Good agreement is found with SCR height spectra for the 12th (when the SCR was operable). Also, surprisingly good agreement is found between ROWS slope spectra and SIR-B image spectra for both the 11th and 12th for both swell and local wind-sea components. ROWS altimeter mode estimates of maximum winds of about 10 m/s on the 11th and 12th are seen to be consistent with the ROWS spectrometer mode observed local wind-sea peak frequencies of about 0.12-0.14 Hz.

Jackson, F. C.↗
NASA NTRS1992

The Split Window Microwave Radiometer (SWMR) for hurricane wind speed measurement from space

The monitoring of hurricanes demands considerable resources each year by the National Oceanic and Atmospheric Administration. Even with the extensive use of satellite and airborne probing of those storms, there is still much uncertainty involved in predicting landfall for timely evacuation of people subject to the threat. The concept of the Split Window Microwave Radiometer (SWMR) is to add an additional capability of remotely measuring surface winds to hopefully improve prediction capabilities or at least define the severity of the storm while it is far from land. Some of the present science and observational needs are addressed in this report as are remote sensing limitations which impact the design of a minimal system which can be launched into low earth orbit by a low cost launch system. This study has concluded that wind speed and rain rate maps of hurricanes can be generated with an X-Band radiometer system with an antenna whose aperture is 2 m on a side.

Swift, Calvin T.↗