SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Wind tunnel investigations of effect on static stability of modifications to swept wing fighter aircraft model
Supersonic wind tunnel testing of antennas
Wind tunnel investigation of steady state aerodynamics of composite lift VTOL aircraft model combining rotary and fixed wings
Wind tunnel test of fan-in-fuselage model of vtol aircraft
Tests at Mach 6 and 8 have been conducted on a model of a wind tunnel sound radiation shield which consists of interchangeable circular and wedge-shaped longitudinal rods with gaps between the rods for boundary layer removal. In view of the large effective sweep angle of the circular rods with respect to the local flow, the boundary layer behavior was surprisingly well represented by swept cylinder theory. Laminar flow was maintained up to a maximum local unit Reynolds number of 8 million per foot which would presumably be independent of model length for a given rod diameter by analogy with results on swept cylinders. Reduction in wind-tunnel sound levels within the shielded region of the circular rod model were about 90% of the maximum possible reduction for an ideal shield.
Over the years aerodynamicists have learned to rely heavily on wind-tunnel-model results in predicting the aerodynamic characteristics of conventional aircraft configurations. With the development of V/STOL configurations which have high slipstream deflection angles. such as the four-propeller tilt-wing XC-142A V/STOL aircraft, the reliability of small-scale wind-tunnel-model results in predicting full-scale airplane characteristics needs to be reexamined. Extensive tests have been made by NASA on several sizes of wind-tunnel models of the XC-142A V/STOL configuration and by Ling-Temco-Vought, Inc., on the airplane. These results show that models predict the slow-speed level-flight characteristics very well but that small models underpredict the descent capability of the airplane. Larger scale wind-tunnel models of approximately half size show better agreement with the airplane descent characteristics. It was found from smoke flow studies that small models can also predict the region in which self-generated disturbances will be encountered by tilt-wing configurations in ground proximity.
Wind tunnel investigation of tail buffet at subsonic and transonic speeds
Aerodynamic excitation of tall structures by ground wind using wind tunnel models
A remote control system for wind-tunnel model control surfaces was developed during the Space Shuttle program to make more efficient use of wind-tunnel occupancy time and to aid in gathering the large force test data base necessary for the definition of the Shuttle aerodynamic characteristics. This paper presents a history of the development of the remote system, details of the system and associated equipment, and results from wind-tunnel tests showing the effect of system improvements on experimental data. Wind-tunnel test rate and cost comparisons are made between conventional models with bracketed control surfaces and remote models.
A remote control system for wind-tunnel model control surfaces was developed during the Space Shuttle program to make more efficient use of wind-tunnel occupancy time and to aid in gathering the large force test data base necessary for the definition of the Shuttle aerodynamic characteristics. A history of the development of the remote system, details of the system and associated equipment, and results from wind-tunnel tests showing the effect of system improvements on experimental data are given. Wind-tunnel test rate and cost comparisons are made between conventional models with bracketed control surfaces and remote models.
The use of pressure sensitive luminescent paints is a viable technique for the measurement of surface pressure on wind tunnel models. This technique requires data reduction of images obtained under known as well as test conditions and spatial transformation of the images. A general transform which registers images to subpixel accuracy is presented and the general characteristics of transforms for image registration and their derivation are discussed. Image resection and its applications are described. The mapping of pressure data to the three dimensional model surface for small wind tunnel models to a spatial accuracy of 0.5 percent of the model length is demonstrated.
Rolling Maneuver Load Alleviation (RMLA) was demonstrated on the Active Flexible Wing (AFW) wind tunnel model in the LaRC Transonic Dynamics Tunnel. The design objective was to develop a systematic approach for developing active control laws to alleviate wing incremental loads during roll maneuvers. Using linear load models for the AFW wind-tunnel model which were based on experimental measurements, two RMLA control laws were developed based on a single-degree-of-freedom roll model. The RMLA control laws utilized actuation of outboard control surface pairs to counteract incremental loads generated during rolling maneuvers and roll performance. To evaluate the RMLA control laws, roll maneuvers were performed in the wind tunnel at dynamic pressures of 150, 200, and 250 psf and Mach numbers of .33, .38, and .44, respectively. Loads obtained during these maneuvers were compared to baseline maneuver loads. For both RMLA controllers, the incremental torsion moments were reduced by up to 60 percent at all dynamic pressures and performance times. Results for bending moment load reductions during roll maneuvers varied. In addition, in a multiple function test, RMLA and flutter suppression system control laws were operated simultaneously during roll maneuvers at dynamic pressures 11 percent above the open-loop flutter dynamic pressure.
Rolling Maneuver Load Alleviation (RMLA) has been demonstrated on the Active Flexible Wing (AFW) wind tunnel model in the NASA Langley Transonic Dynamics Tunnel. The design objective was to develop a systematic approach for developing active control laws to alleviate wing incremental loads during roll maneuvers. Using linear load models for the AFW wind-tunnel model which were based on experimental measurements, two RMLA control laws were developed based on a single-degree-of-freedom roll model. The RMLA control laws utilized actuation of outboard control surface pairs to counteract incremental loads generated during rolling maneuvers and actuation of the trailing edge inboard control surface pairs to maintain roll performance. To evaluate the RMLA control laws, roll maneuvers were performed in the wind tunnel at dynamic pressures of 150, 200, and 250 psf and Mach numbers of 0.33, .38 and .44, respectively. Loads obtained during these maneuvers were compared to baseline maneuver loads. For both RMLA controllers, the incremental torsion moments were reduced by up to 60 percent at all dynamic pressures and performance times. Results for bending moment load reductions during roll maneuvers varied. In addition, in a multiple function test, RMLA and flutter suppression system control laws were operated simultaneously during roll maneuvers at dynamic pressures 11 percent above the open-loop flutter dynamic pressure.
Measurements and analytical extrapolation validity in predicting full scale flight performance from model wind tunnel tests
Wind tunnel studies of scaled model of multijet cargo airplane
The problem of dimensional instability in airfoil models for cryogenic wind tunnels is discussed in terms of the various mechanisms that can be responsible. The interrelationship between metallurgical structure and possible dimensional instability in cryogenic usage is discussed for those steel alloys of most interest for wind tunnel model construction at this time. Other basic mechanisms responsible for setting up residual stress systems are discussed, together with ways in which their magnitude may be reduced by various elevated or low temperature thermal cycles. A standard specimen configuration is proposed for use in experimental investigations into the effects of machining, heat treatment, and other variables that influence the dimensional stability of the materials of interest. A brief classification of various materials in terms of their metallurgical structure and susceptability to dimensional instability is presented.
Aircraft icing occurs when a plane flies through a cloud of supercooled water droplets. When the droplets impinge on aircraft components, ice starts to form and accumulate. This accumulation of ice severely increases the drag and lift of the aircraft, and can ultimately lead to catastrophic failures and even loss of life. Knowledge of the air pressures on the surfaces of ice and models in wind tunnels allows researchers to better predict the effects that different icing conditions will have on the performance of real aircraft. The use of pressure-sensitive paint (PSP) has provided valuable information on similar problems in conventional wind tunnel testing. In NASA Lewis Research Center Icing Research Tunnel, Lewis researchers recently demonstrated the world s first application of PSP on actual ice formed on a wind tunnel model. This proof-of-concept test showed that a new paint formulation developed under a grant by the University of Washington adheres to both the ice shapes and cold aluminum models, provides a uniform coating that preserves the detailed ice shape structure, and responds to simulated pressure changes.
As an alternative to conventional tubing instrumentation for measuring airflow, designers and technicians at Glenn Research Center have been fabricating packaging components and assembling a set of unique probes that contain commercial off-the-shelf (COTS) microelectromechanical systems (MEMS) sensor chips. MEMS sensor chips offer some compelling advantages over standard macroscopic measurement devices. MEMS sensor technology has matured through mass production and use in the automotive and aircraft industries. At present, MEMS are the devices of choice for sensors in such applications as tire-pressure monitors, altimeters, pneumatic controls, cable leak detectors, and consumer appliances. Compactness, minimality of power demand, rugged construction, and moderate cost all contribute to making MEMS sensors attractive for instrumentation for future research. Conventional macroscopic flow-measurement instrumentation includes tubes buried beneath the aerodynamic surfaces of wind-tunnel models or in wind-tunnel walls. Pressure is introduced at the opening of each such tube. The pressure must then travel along the tube before reaching a transducer that generates an electronic signal. The lengths of such tubes typically range from 20 ft (approx.= 6 m) to hundreds of feet (of the order of 100 m). The propagation of pressure signals in the tubes damps the signals considerably and makes it necessary to delay measurements until after test rigs have reached steady-state operation. In contrast, a MEMS pressure sensor that generates electronic output can take readings continuously under dynamic conditions in nearly real time. In order to use stainless-steel tubing for pressure measurements, it is necessary to clean many tubes, cut them to length, carefully install them, delicately deburr them, and splice them. A cluster of a few hundred 1/16-in.- (approx.=1.6-mm-) diameter tubes (such clusters are common in research testing facilities) can be several inches (of the order of 10 cm) in diameter and could weigh enough that two technicians are needed to handle it. Replacing hard tubing with electronic chips can eliminate much of the bulk. Each sensor would fit on the tip of a 1/16-in. tube with room to spare. The Lucas NovaSensor P592 piezoresistive silicon pressure sensor was chosen for this project because of its cost, availability, and tolerance to extreme ambient conditions. The sensor chip is 1 mm square by 0.6 mm thick (about 0.039 by 0.039 by 0.024 in.) and includes 0.12-mm (approx.=0.005-in.) wire connection tabs. The figure shows a flow-angularity probe that was built by use of three such MEMS chips. It is planned to demonstrate this MEMS probe as an alternative to a standard tube-type "Cobra" probe now used routinely in wind tunnels and aeronautical hardware. This MEMS probe could be translated across a flow field by use of a suitable actuator, so that its accuracy and the shortness of its response time could be exploited to obtain precise dynamic measurements of a sort that cannot be made by use of conventional tubing-based instrumentation.