Search NASA⌕ Search

SEARCH · Search NASA

Results for “anchoring”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS2009

Development of a Methodology to Gather Seated Anthropometry in a Microgravity Environment

The Constellation Program's Crew Exploration Vehicle (CEV) is required to accommodate the full population range of crewmembers according to the anthropometry requirements stated in the Human-Systems Integration Requirement (HSIR) document (CxP70024). Seated height is one of many critical dimensions of importance to the CEV designers in determining the optimum seat configuration in the vehicle. Changes in seated height may have a large impact to the design, accommodation, and safety of the crewmembers. Seated height can change due to elongation of the spine when crewmembers are exposed to microgravity. Spinal elongation is the straightening of the natural curvature of the spine and the expansion of inter-vertebral disks. This straightening occurs due to fluid shifts in the body and the lack of compressive forces on the spinal vertebrae. Previous studies have shown that as the natural curvature of the spine straightens, an increase in overall height of 3% of stature occurs which has been the basis of the current HSIR requirements. However due to variations in the torso/leg ratio and impact of soft tissue, data is nonexistent as to how spinal elongation specifically affects the measurement of seated height. In order to obtain this data, an experiment was designed to collect spinal elongation data while in a seated posture in microgravity. The purpose of this study was to provide quantitative data that represents the amount of change that occurs in seated height due to spinal elongation in microgravity environments. Given the schedule and budget constraints of ISS and Shuttle missions and the uniqueness of the problem, a methodology had to be developed to ensure that the seated height measurements were accurately collected. Therefore, simulated microgravity evaluations were conducted to test the methodology and procedures of the experiment. This evaluation obtained seat pan pressure and seated height data to a) ensure that the lap restraint provided sufficient restraint to eliminate any gap between the subject s gluteal surface and the seat pan and b) to document any necessary design and procedural changes needed due to the microgravity environment. The methodology and setup used during the simulated microgravity evaluations was replicable to the proposed methodology and setup for in-space missions. A flight-like Shuttle seat, pressure sensors, anthropometer, and existing hardware was used to measure seated height and contact area while experiencing microgravity. The outlying buttock and thigh surface contact areas were collected to determine if the subjects were in contact with the seat pan, while a measurer recorded their seated height with an anthropometer. The Anthropometry and Biomechanics Facility (ABF) completed data collection from three microgravity flights to assess the restraint methods and techniques to be used for the in-flight procedures performed by the crewmembers in orbit. The first flight demonstrated that the restraint system on the seat, used in a nominal configuration, did not sufficiently restrain a person in the seat. The results showed the subjects were not in full contact with the seat pan, resulting in inaccurate sitting height data. Thus, a second flight was conducted to test different restraint system options. The results showed that by 1) changing the restraint system from the nominal 3-points of the 5-point harness, which is used for crewmembers when fully suited with emergency equipment, and 2) rerouting the lap straps around the joint of the backrest, where the backrest and seat pan are joined, resulted in the optimal method to restrain a subject. This rerouting method allowed for the anchor location to change and pull the subjects back into the seat instead of being anchored at the side of the subjects thighs. The results from the third flight validated the final restraint system, which resulted in a verified methodology for collecting seated anthropometry to ultimately determine the amount of spil elongation in a microgravity environment.

Rajulu, Sudhakar↗
NASA NTRS2010

Combustion Stability Analyses for J-2X Gas Generator Development

The National Aeronautics and Space Administration (NASA) is developing a liquid oxygen/liquid hydrogen rocket engine for upper stage and trans-lunar applications of the Ares vehicles for the Constellation program. This engine, designated the J-2X, is a higher pressure, higher thrust variant of the Apollo-era J-2 engine. Development was contracted to Pratt & Whitney Rocketdyne in 2006. Over the past several years, development of the gas generator for the J-2X engine has progressed through a variety of workhorse injector, chamber, and feed system configurations. Several of these configurations have resulted in injection-coupled combustion instability of the gas generator assembly at the first longitudinal mode of the combustion chamber. In this paper, the longitudinal mode combustion instabilities observed on the workhorse test stand are discussed in detail. Aspects of this combustion instability have been modeled at the NASA Marshall Space Flight Center with several codes, including the Rocket Combustor Interaction Design and Analysis (ROCCID) code and a new lumped-parameter MatLab model. To accurately predict the instability characteristics of all the chamber and injector geometries and test conditions, several features of the submodels in the ROCCID suite of calculations required modification. Finite-element analyses were conducted of several complicated combustion chamber geometries to determine how to model and anchor the chamber response in ROCCID. A large suite of sensitivity calculations were conducted to determine how to model and anchor the injector response in ROCCID. These modifications and their ramification for future stability analyses of this type are discussed in detail. The lumped-parameter MatLab model of the gas generator assembly was created as an alternative calculation to the ROCCID methodology. This paper also describes this model and the stability calculations.

Hulka, J. R.↗
NASA NTRS2010

Robotic Lunar Landers for Science and Exploration

NASA Marshall Space Flight Center and The Johns Hopkins University Applied Physics Laboratory has been conducting mission studies and performing risk reduction activities for NASA s robotic lunar lander flight projects. In 2005, the Robotic Lunar Exploration Program Mission #2 (RLEP-2) was selected as a Exploration Systems Mission Directorate precursor robotic lunar lander mission to demonstrate precision landing and definitively determine if there was water ice at the lunar poles; however, this project was canceled. Since 2008, the team has been supporting NASA s Science Mission Directorate designing small lunar robotic landers for diverse science missions. The primary emphasis has been to establish anchor nodes of the International Lunar Network (ILN), a network of lunar science stations envisioned to be emplaced by multiple nations. This network would consist of multiple landers carrying instruments to address the geophysical characteristics and evolution of the moon. Additional mission studies have been conducted to support other objectives of the lunar science community and extensive risk reduction design and testing has been performed to advance the design of the lander system and reduce development risk for flight projects. This paper describes the current status of the robotic lunar mission studies that have been conducted by the MSFC/APL Robotic Lunar Lander Development team, including the ILN Anchor Nodes mission. In addition, the results to date of the lunar lander development risk reduction efforts including high pressure propulsion system testing, structure and mechanism development and testing, long cycle time battery testing and combined GN&C and avionics testing will be addressed. The most visible elements of the risk reduction program are two autonomous lander test articles: a compressed air system with limited flight durations and a second version using hydrogen peroxide propellant to achieve significantly longer flight times and the ability to more fully exercise flight sensors and algorithms. Robotic Lunar Lander design and development will have significant feed-forward to other missions to the Moon and, indeed, to other airless bodies such as Mercury, asteroids, and Europa, to which similar science and exploration objectives are applicable.

Cohen, B. A.↗
NASA NTRS2005

Ex Vivo Growth of Bioengineered Ligaments and Other Tissues

A method of growing bioengineered tissues for use in surgical replacement of damaged anterior cruciate ligaments has been invented. An anterior cruciate ligament is one of two ligaments (the other being the posterior cruciate ligament) that cross in the middle of a knee joint and act to prevent the bones in the knee from sliding forward and backward relative to each other. Anterior cruciate ligaments are frequently torn in sports injuries and traffic accidents, resulting in pain and severe limitations on mobility. By making it possible to grow replacement anterior cruciate ligaments that structurally and functionally resemble natural ones more closely than do totally synthetic replacements, the method could create new opportunities for full or nearly full restoration of functionality in injured knees. The method is also adaptable to the growth of bioengineered replacements for other ligaments (e.g., other knee ligaments as well as those in the hands, wrists, and elbows) and to the production of tissues other than ligaments, including cartilage, bones, muscles, and blood vessels. The method is based on the finding that the histomorphological properties of a bioengineered tissue grown in vitro from pluripotent cells within a matrix are affected by the direct application of mechanical force to the matrix during growth generation. This finding provides important new insights into the relationships among mechanical stress, biochemical and cell-immobilization methods, and cell differentiation, and is applicable to the production of the variety of tissues mentioned above. Moreover, this finding can be generalized to nonmechanical (e.g., chemical and electromagnetic) stimuli that are experienced in vivo by tissues of interest and, hence, the method can be modified to incorporate such stimuli in the ex vivo growth of replacements for the various tissues mentioned above. In this method, a three-dimensional matrix made of a suitable material is seeded with pluripotent stem cells. The patient s bone-marrow stromal cells are preferably used as the pluripotent cells in this method. Suitable matrix materials are materials to which cells can adhere for example, collagen type I. The seeded matrix is attached to anchors at opposite ends and then the cells in the matrix are cultured under conditions appropriate for the growth and regeneration of cells. Suitable anchor materials are materials to which the matrix can attach; examples include demineralized bone and Goinopra coral that has been treated to convert its calcium carbonate to calcium phosphate.

Altman, Gregory↗
NASA NTRS2005

Growing Aligned Carbon Nanotubes for Interconnections in ICs

A process for growing multiwalled carbon nanotubes anchored at specified locations and aligned along specified directions has been invented. Typically, one would grow a number of the nanotubes oriented perpendicularly to a silicon integrated-circuit (IC) substrate, starting from (and anchored on) patterned catalytic spots on the substrate. Such arrays of perpendicular carbon nanotubes could be used as electrical interconnections between levels of multilevel ICs. The process (see Figure 1) begins with the formation of a layer, a few hundred nanometers thick, of a compatible electrically insulating material (e.g., SiO(x) or Si(y)N(z) on the silicon substrate. A patterned film of a suitable electrical conductor (Al, Mo, Cr, Ti, Ta, Pt, Ir, or doped Si), having a thickness between 1 nm and 2 m, is deposited on the insulating layer to form the IC conductor pattern. Next, a catalytic material (usually, Ni, Fe, or Co) is deposited to a thickness between 1 and 30 nm on the spots from which it is desired to grow carbon nanotubes. The carbon nanotubes are grown by plasma-enhanced chemical vapor deposition (PECVD). Unlike the matted and tangled carbon nanotubes grown by thermal CVD, the carbon nanotubes grown by PECVD are perpendicular and freestanding because an electric field perpendicular to the substrate is used in PECVD. Next, the free space between the carbon nanotubes is filled with SiO2 by means of CVD from tetraethylorthosilicate (TEOS), thereby forming an array of carbon nanotubes embedded in SiO2. Chemical mechanical polishing (CMP) is then performed to remove excess SiO2 and form a flat-top surface in which the outer ends of the carbon nanotubes are exposed. Optionally, depending on the application, metal lines to connect selected ends of carbon nanotubes may be deposited on the top surface. The top part of Figure 2 is a scanning electron micrograph (SEM) of carbon nanotubes grown, as described above, on catalytic spots of about 100 nm diameter patterned by electron-beam lithography. These and other nanotubes were found to have lengths ranging from 2 to 10 m and diameters ranging from 30 to 200 nm, the exact values of length depending on growth times and conditions and the exact values of diameter depending on the diameters and thicknesses of the catalyst spots. The bottom part of Figure 2 is an SEM of an embedded array of carbon nanotubes after CMP.

Li, Jun↗
NASA NTRS2005

Alternative Way of Shifting Mass to Move a Spherical Robot

The method proposed calls for suspending a payload by use of four or more cables that would be anchored to the inner surface of the sphere. In this method, the anchor points would not be diametrically opposite points defining Cartesian axes. The payload, which includes the functional analog of the aforementioned control box, would contain winches that would shorten or lengthen the cables in a coordinated manner to shift the position of the payload within the shell.

Lux, James↗
NASA NTRS2011

Analyses of Longitudinal Mode Combustion Instability in J-2X Gas Generator Development

The National Aeronautics and Space Administration (NASA) and Pratt & Whitney Rocketdyne are developing a liquid oxygen/liquid hydrogen rocket engine for future upper stage and trans-lunar applications. This engine, designated the J-2X, is a higher pressure, higher thrust variant of the Apollo-era J-2 engine. The contract for development was let to Pratt & Whitney Rocketdyne in 2006. Over the past several years, development of the gas generator for the J-2X engine has progressed through a variety of workhorse injector, chamber, and feed system configurations on the component test stand at the NASA Marshall Space Flight Center (MSFC). Several of the initial configurations resulted in combustion instability of the workhorse gas generator assembly at a frequency near the first longitudinal mode of the combustion chamber. In this paper, several aspects of these combustion instabilities are discussed, including injector, combustion chamber, feed system, and nozzle influences. To ensure elimination of the instabilities at the engine level, and to understand the stability margin, the gas generator system has been modeled at the NASA MSFC with two techniques, the Rocket Combustor Interaction Design and Analysis (ROCCID) code and a lumped-parameter MATLAB(TradeMark) model created as an alternative calculation to the ROCCID methodology. To correctly predict the instability characteristics of all the chamber and injector geometries and test conditions as a whole, several inputs to the submodels in ROCCID and the MATLAB(TradeMark) model were modified. Extensive sensitivity calculations were conducted to determine how to model and anchor a lumped-parameter injector response, and finite-element and acoustic analyses were conducted on several complicated combustion chamber geometries to determine how to model and anchor the chamber response. These modifications and their ramification for future stability analyses of this type are discussed.

Hulka, J. R.↗
NASA NTRS2012

The Development and Hover Test Application of a Projection Moire Interferometry Blade Displacement Measurement System

Projection moir interferometry (PMI) was employed to measure blade deflections during a hover test of a generic model-scale rotor in the NASA Langley 14x22 subsonic wind tunnel s hover facility. PMI was one of several optical measurement techniques tasked to acquire deflection and flow visualization data for a rotor at several distinct heights above a ground plane. Two of the main objectives of this test were to demonstrate that multiple optical measurement techniques can be used simultaneously to acquire data and to identify and address deficiencies in the techniques. Several PMI-specific technical challenges needed to be addressed during the test and in post-processing of the data. These challenges included developing an efficient and accurate calibration method for an extremely large (65 inch) height range; automating the analysis of the large amount of data acquired during the test; and developing a method to determinate the absolute displacement of rotor blades without a required anchor point measurement. The results indicate that the use of a single-camera/single-projector approach for the large height range reduced the accuracy of the PMI system compared to PMI systems designed for smaller height ranges. The lack of the anchor point measurement (due to a technical issue with one of the other measurement techniques) limited the ability of the PMI system to correctly measure blade displacements to only one of the three rotor heights tested. The new calibration technique reduced the data required by 80 percent while new post-processing algorithms successfully automated the process of locating rotor blades in images, determining the blade quarter chord location, and calculating the blade root and blade tip heights above the ground plane.

Sekula, Martin K.↗
NASA NTRS2011

Manned NEO Mission EVA Challenges

The President has proposed to land astronauts on an asteroid by 2025. However, Manned NEO (Near Earth Objects) Missions will present a host of new and exciting problems that will need to be better defined and solved before such a mission is launched. Here I will focus on the challenges for conducting asteroidal EVAs. Specfically, crew locomotion, sampling, drilling, documentation, and instrument deployment issues arising from the micro gravity environments associated with NEOs. Therefore, novel methods and techniques will need to be developed and tested in order to achieve specific mission science objectives. Walking or driving on the surface will not be a realistic option due to the small sizes (10 s to 100 s of meters in diameter) and hence extremely low gravity of the present day known candidate NEOs. EVAs will have to be carried out with crew members either using a self propelled device (akin to the MMU and SAFER units used on Shuttle/ISS) and or tethers. When using tethers a grid system could be deployed which is anchored to the asteroid. These anchor points could be inserted by firing penetrators into the surface from the spacecraft while it is still at a safe standoff distance. These penetrators would pull double duty by being laden with scientific instrumentation to probe the subsurface. Dust and debris generated by sample collection and locomotion in a microgravity environment could also pose some problems that will require forethought.

Source record↗
NASA NTRS2012

Antenna Deployment for a Pathfinder Lunar Radio Observatory

A first step in the development of a large radio observatory on the moon for cosmological or other astrophysical and planetary goals is to deploy a few antennas as a pathfinder mission. In this presentation, we describe a mechanism being developed to deploy such antennas from a small craft, such as a Google Lunar X-prize lander. The antenna concept is to deposit antennas and leads on a polyimide film, such as Kapton, and to unroll the film on the lunar surface. The deployment technique utilized is to launch an anchor which pulls a double line from a reel at the spacecraft. Subsequently, the anchor is set by catching on the surface or collecting sufficient regolith. A motor then pulls in one end of the line, pulling the film off of its roller onto the lunar surface. Detection of a low frequency cutoff of the galactic radio background or of solar radio bursts by such a system would determine the maximum lunar ionospheric density at the time of measurement. The current design and testing, including videos of the deployment, will be presented. These activities are funded in part by the NASA Lunar Science Institute as an activity of the Lunar University Network for Astrophysical Research (LUNAR) consortium. Part of this research was carried out at the Jet Propulsion Laboratory, California Institute of Technology, under a contract with the National Aeronautics and Space Administration.

MacDowall, Robert J.↗
NASA NTRS2012

CRYogenic Orbital TEstbed Ground Test Article Thermal Analysis

The purpose of this study was to anchor thermal and fluid system models to CRYOTE ground test data. The CRYOTE ground test artide was jointly developed by Innovative Engineering Solutions, United Launch Alliance and NASA KSC. The test article was constructed out of a titanium alloy tank, Sapphire 77 composite skin (similar to G10), an external secondary payload adapter ring, thermal vent system, multi layer insulation and various data acquisition instrumentation. In efforts to understand heat loads throughout this system, the GTA (filled with liquid nitrogen for safety purposes) was subjected to a series of tests in a vacuum chamber at Marshall Space Flight Center. By anchoring analytical models against test data, higher fidelity thermal environment predictions can be made for future flight articles which would eventually demonstrate critical cryogenic fluid management technologies such as system chilldown, transfer, pressure control and long term storage. Significant factors that influenced heat loads included radiative environments, multi-layer insulation performance, tank fill levels and pressures and even contact conductance coefficients. This report demonstrates how analytical thermal/fluid networks were established and includes supporting rationale for specific thermal responses.

Piryk, David↗
NASA NTRS2011

Modeling and Simulation for Multi-Missions Space Exploration Vehicle

Asteroids and Near-Earth Objects [NEOs] are of great interest for future space missions. The Multi-Mission Space Exploration Vehicle [MMSEV] is being considered for future Near Earth Object missions and requires detailed planning and study of its Guidance, Navigation, and Control [GNC]. A possible mission of the MMSEV to a NEO would be to navigate the spacecraft to a stationary orbit with respect to the rotating asteroid and proceed to anchor into the surface of the asteroid with robotic arms. The Dynamics and Real-Time Simulation [DARTS] laboratory develops reusable models and simulations for the design and analysis of missions. In this paper, the development of guidance and anchoring models are presented together with their role in achieving mission objectives and relationships to other parts of the simulation. One important aspect of guidance is in developing methods to represent the evolution of kinematic frames related to the tasks to be achieved by the spacecraft and its robot arms. In this paper, we compare various types of mathematical interpolation methods for position and quaternion frames. Subsequent work will be on analyzing the spacecraft guidance system with different movements of the arms. With the analyzed data, the guidance system can be adjusted to minimize the errors in performing precision maneuvers.

Multi-Mission Space Exploration Vehicle [MMSEV]↗
NASA NTRS2012

Methods for Improving Long-Range Wireless Communication Between Extreme Terrain Vehicles

Axel is an extreme terrain, two-wheeled rover designed to traverse rocky surface and sub-surface landscapes in order to conduct remote science experiments in hard-to-reach locations. The rover's design meets many requirements for a mobile research platform capable of reaching water seeps on Martian cliff sides. Axel was developed by the Mobility and Robotic Systems section at the Caltech Jet Propulsion Laboratory. Unique design criteria associated with extreme terrain mobility led to a unique rover solution, consisting of a central module, which provides long-term energy storage and space for large-scale science payloads, and two detachable Axels that can detach and explore extreme terrain locations that are inaccessible to conventional rovers. The envisioned mission could involve a four-wheeled configuration of Axel called 'DuAxel' that is able to traverse the benign, flattened terrain of a landing site and approach the edge of the targeted crater or cave where it would deploy anchoring legs and detach one of the Axel rovers [1]. A tether provides a secure link between the Axel rover and the central module, acting as an anchor to allow Axel to descend along steep crater walls to collect data from the scientifically relevant sites along the water seeps or crater ledges. After completing its scientific mission Axel would hoist itself up to the central module and dock autonomously (using its on-board stereo cameras), allowing the once-again recombined DuAxel to travel to another location to repeat data collection.

wireless communication↗
NASA NTRS2012

Curb Mounting, Vertical Mobility, and Inverted Mobility on Rough Surfaces Using Microspine-Enabled Robots

Three robots that extend microspine technology to enable advanced mobility are presented. First, the Durable Reconnaissance and Observation Platform (DROP) and the ReconRobotics Scout platform use a new rotary configuration of microspines to provide improved soldier-portable reconnaissance by moving rapidly over curbs and obstacles, transitioning from horizontal to vertical surfaces, climbing rough walls and surviving impacts. Next, the four-legged LEMUR robot uses new configurations of opposed microspines to anchor to both manmade and natural rough surfaces. Using these anchors as feet enables mobility in unstructured environments, from urban disaster areas to deserts and caves.

microspines↗
NASA NTRS2015

Deployable Emergency Shutoff Device Blocks High-Velocity Fluid Flows

NASA's Marshall Space Flight Center has developed a device and method for blocking the flow of fluid from an open pipe. Motivated by the sea-bed oil-drilling catastrophe in the Gulf of Mexico in 2010, NASA innovators designed the device to plug, control, and meter the flow of gases and liquids. Anchored with friction fittings, spikes, or explosively activated fasteners, the device is well-suited for harsh environments and high fluid velocities and pressures. With the addition of instrumentation, it can also be used as a variable area flow metering valve that can be set based upon flow conditions. With robotic additions, this patent-pending innovation can be configured to crawl into a pipe then anchor and activate itself to block or control fluid flow.

Nabors, Sammy A.↗
NASA NTRS2016

Seismic Exploration of Small Bodies

As a result of the Phase I study, we have demonstrated that a mission to a smallbody (asteroid, comet) whose objective is to conduct a seismic experiment to understandthe interior structure, can be accomplished with small (<200 kg) spacecraft launched on asmall launch vehicle (Athena IIc).We modeled the seismic response of a small body and calculated that the energynecessary to propagate through the body and be detected by a seismometer. Thesecalculations provide guidance as to the type of energy source that is required. A simpleenergy source similar to a NASA standard initiator (NSI) can be used, although a singleNSI is insufficient. An NSI is an explosive pyrotechnic that is used to sever connectionson spacecraft. Use of such an energy source has illustrated two additional areas of study -anchoring of the source and sensor to the surface and understanding the efficiency ofenergy propagation from the source into the surface.The spacecraft has the ability to carry and deploy a series of source/sensors toconduct the experiment by placing them on the surface. We identified a suite of candidatenear-Earth asteroids as targets and used one 1991VG as the target to calculate the missiontrajectory and ∆V requirements. Spacecraft and launch vehicle performance are launchthat any of the candidates could be reached with appropriate mass and launch margins.Sources and sensors are deployed from arm attached to the spacecraft. Thespacecraft maneuvers next to the target body and presses the sensor against the surfaceand releases it. After emplacing all of the surface packages, the sensors are monitored fora period of time to measure the seismic noise. Finally, the active seismic experiment isconducted.The work conducted during Phase I demonstrates that a small mission can be designed to conduct an active seismic experiment on a small near-Earth body. Whileother targets may require more performance, the basic architecture is viable for anytarget.We have identified a number of specific technical areas that require more detailed study. Those areas are largely focused on the detailed analysis and design of the source mechanism and anchoring it to the surface. Such topics will be part of a Phase IIproposal.

Spacecraft↗
NASA NTRS2019

Towards Articulated Mobility and Efficient Docking for the DuAxel Tethered Robot System

Sites of increasing interest for planetary science,such as craters, cold traps, and vents lie in terrains that are inaccessible to state-of-the-art rovers. The Jet Propulsion Laboratory, in collaboration with Caltech, is actively developing a tethered mobile robot, Axel, for traversing and exploring extremely steep terrain, such as Recurring Slope Lineae on Mars and vertical pits on the Moon. However, on Mars, where landing-site uncertainty is high due to the presence of an atmosphere, Axel may need to traverse several kilometers from its lander untethered due to a finite tether carrying capacity (⇠300m). This paper proposes a novel design for a hybrid mobility system that allows a pair of Axel rovers to dock, lock, and drive long distances as a four-wheeled, articulated steering vehicle. The design improves upon prior efforts to achieve DuAxel mobility by leveraging two actuated docking mechanisms attached on opposite ends of a central module to enable ‘sit/stand’ functionality; the prior DuAxel system was limited to skid steering, which was inefficient due to Axel’s grouser-style, high-friction wheels. In the proposed system, the ‘sit’ configuration is achieved by aligning each dock parallel to the surface, allowing one Axel to detach and explore while the other remains docked and serves as a backup. While ‘sitting’, the central module rests on the ground and is outfitted with shovel-style wedges for passive anchoring to sandy terrain (an optional drill can be integrated for anchoring to rock). In order to ‘stand’, the exploring Axel reattaches, locks, and both docks are rotated until Axel’s tether caster arm is upright and the central module is lifted off the ground. Once upright, each Axel rotates about a pivot point for articulated, all-wheel steering, which is accomplished by applying differential wheel torques. The main contributions of this paper are i) a detailed systems design of the docking mechanism and central module, ii) kinematic modeling of articulated mobility and ‘sit/stand’ docking functionality, and iii) initial testing in a relevant environment to characterize the mobility of the proposed system.

Nesnas, Issa↗
NASA NTRS2021

Confronting Future Models with Future Satellite Observations of Clouds and Aerosols

The NASA Aerosol, Clouds, Convection and Precipitation (ACCP) Study convened a workshop in November 2020 to understand the future of modeling aerosols, clouds, convection and precipitation, and how satellite data can contribute to that future. ACCP is a project to define a satellite mission to be launched late in the 2020’s to advance cloud and aerosol science, following the recommendations of the latest NASA Decadal Survey. The ACCP modeling workshop goal was to answer the following questions: 1. What will be the critical science questions for clouds and aerosols in 10 years? 2. Where will simulations of clouds and aerosols across scales of space (process models to global) and time (nowcasting to climate prediction) be in 10 years? 3. What data will be available from space? What data would provide the most benefit? 4. What are the state of the art methods for confronting models with cloud and aerosol observations, including assimilation and climatological analysis techniques? The virtual workshop was anchored by a series of pre-recorded talks. Two days of synchronous sessions focused on discussion of the talks, along with small group breakout exercises. After an introduction to the ACCP concept came a panel discussing the future of modeling clouds and aerosols across scales. Participants were then asked to contribute their ideas. On the second day, there were two panel discussions. First came a discussion of the future of satellite observing systems. Second was a discussion of model-data synthesis methods. Finally, participants were asked to develop their own model-data synthesis proposal. The meeting began with an overview of the ACCP mission concept by Graeme Stephens (NASA-JPL). ACCP is a satellite mission for clouds and aerosols, likely anchored by advanced active lidar and radar systems in space, designed to observe detailed aerosol profile and type information, as well as cloud microphysics and dynamics. ACCP will integrate across sensors and observational types to get multi-spectral views of the same scenes, with better resolution than is available today. Launch is scheduled for 2027 or 2029. ACCP is being thought of as a comprehensive mission that may comprise more than one platform and more than one orbit plane (i.e., inclined and polar), with multiple combinations of sensors.

Future Models↗