Search NASA⌕ Search

SEARCH · Search NASA

Results for “attack modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

Wind-Tunnel Measurements of Effect of Dive-Recovery Flaps at Transonic Speeds on Models of a Seaplane and a Transport

The effects of wing-lower-surface dive-recovery flaps on the aero- dynamic characteristics of a transonic seaplane model and a transonic transport model having 40 deg swept wings have been investigated in the Langley 16-foot transonic tunnel. The seaplane model had a wing with an aspect ratio of 5.26, a taper ratio of 0.333, and NACA 63A series airfoil sections streamwise. The transport model had a wing with an aspect ratio of 8, a taper ratio of 0.3, and NACA 65A series airfoil sections perpendicular to the quarter-chord line. The effects of flap deflection, flap longitudinal location, and flap sweep were generally investigated for both horizontal-tail-on and horizontal-tail-off configurations. Model force and moment measurements were made for model angles of attack from -5 deg to 14 deg in the Mach number range from 0.70 to 1.075 at Reynolds numbers of 2.95 x 10(exp 6) to 4.35 x 10(exp 6). With proper longitudinal location, wing-lower-surface dive-recovery flaps produced lift and pitching-moment increments that increased with flap deflection. For the transport model a flap located aft on the wing proved to be more effective than one located more forward., both flaps having the same span and approximately the same deflection. For the seaplane model a high horizontal tail provided added effectiveness for the deflected-flap configuration.

Heath, Atwood R., Jr.↗

Unsteady Pressure Measurements on a Simplified High-Lift Configuration of the Common Research Model using Active Flow Control

The High-Lift Common Research Model (CRM-HL) is a product of the NASA Advanced Air Transport Technology (AATT) Project intended to study various high-lift aerodynamic phenomena including enhanced lift, acoustic noise generation, and optimum placement of leading and trailing-edge devices. The current study was conducted in the NASA Langley 14-by 22-Foot Subsonic Tunnel (14x22) for the purpose of evaluating enhanced lift through the use of active flow control (AFC). The current paper documents the effect of sweeping-jet actuation combined with steady blowing on a simplified high-lift configuration using unsteady pressure measurements. The time-series parameters for the measurements are documented as well as the data acquisition system used to acquire the data. An uncertainty analysis will be presented in order to document the system performance and provide an estimate of the data quality. Repeatability of the data will be shown along with trends associated with model angle of attack, and also those associated with changes in the nozzle pressure ratio (NPR) of the AFC system.

Active Flow Control↗

STOVL CFD model test case

The transitional flight characteristics of a geometrically simplified Short Take-Off Vertical Landing (STOVL) aircraft configuration have been measured in the NASA Ames 7- by 10-Foot Wind Tunnel. The experiment is the first in a sequence of tests designed to provide detailed data for evaluating the capability of computational fluid dynamics methods to predict the important flow parameters for powered lift. The model consists of a 60 deg cropped delta wing platform, blended fuselage and two circular in-line jets that exit perpendicularly from the flat lower surface. The measured flows have a maximum freestream Mach number of 0.2. Model angle of attack is varied between -10 and +20 deg. The flow is ambient temperature in both jet exits and the nozzle pressure ratios are varied between 1 and 3. The data presented includes forces and moments, pressures measured at 281 surface pressure ports and the pressures of the jets. Measurements of the flow are also made in the tunnel test section upstream and downstream of the model and at the jet exits to guide boundary condition selection for the planned computations. Flow visualization and total pressure measurements in the jet plumes provide a description of the three-dimensional jet efflux flowfield.

Roth, Karlin R.↗

Evaluating cyber-risk in synchrophasor systems

Technology related to evaluating cyber-risk for synchrophasor systems is disclosed. In one example of the disclosed technology, a method includes generating an event tree model of a timing-attack on a synchrophasor system architecture. The event tree model can be based on locations and types of timing-attacks, an attack likelihood, vulnerabilities and detectability along a scenario path, and consequences of the timing-attack. A cyber-risk score of the synchrophasor system architecture can be determined using the event tree model. The synchrophasor system architecture can be adapted in response to the cyber-risk score.

Pal, Seemita↗

An Artificially Intelligent Physical Model-Checking Approach to Detect Switching-Related Attacks on Power Systems

Decentralized and hierarchical microgrid control strategies have lain the groundwork for shaping the future smart grid. Such control approaches require the cooperation between microgrid operators in control centers, intelligent microcontrollers, and remote terminal units via secure and reliable communication networks. In order to enhance the security and complement the work of network intrusion detection systems, this paper presents an artificially intelligent physical model-checking that detects tampered-with circuit breaker switching control commands whether, due to a cyber-attack or human error. In this technique, distributed agents, which are monitoring sectionalized areas of a given microgrid, will be trained and continuously adapted to verify that incoming control commands do not violate the physical system operational standards and do not put the microgrid in an insecure state. The potential of this approach has been tested by deploying agents that monitor circuit breakers status commands on a 14-bus IEEE benchmark system. The results showed the accuracy of the proposed framework in characterizing the power system and successfully detecting malicious and/or erroneous control commands.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Supersonic aerodynamic characteristics of a circular body Earth-to-Orbit vehicle

The circular body configuration is a generic single- or multi-stage reusable Earth-to-orbit transport. A thick clipped-delta wing is the major lifting surface. For directional control, three different vertical fin arrangements were investigated: a conventional aft-mounted center fin, wingtip fins, and a nose-mounted fin. The tests were conducted in the Langley Unitary Plan Wind Tunnel. The configuration is longitudinally stable about the estimated center of gravity of 0.72 body length up to a Mach number of about 3.0. Above Mach 3.0, the model is longitudinally unstable at low angles of attack but has a stable secondary trim point at angles of attack above 30 deg. The model has sufficient pitch control authority with elevator and body flap to produce stable trim over the test range. The model with the center fin is directionally stable at low angles of attack up to a Mach number of 3.90. The rudder-like surfaces on the tip fins and the all-movable nose fin are designed as active controls to produce artificial directional stability and are effective in producing yawing moment. The wing trailing-edge aileron surfaces are effective in producing rolling moment, but they also produce large adverse yawing moment.

Ware, George M.↗

A prediction model for lift-fan simulator performance

The performance characteristics of a model VTOL lift-fan simulator installed in a two-dimensional wing are presented. The lift-fan simulator consisted of a 15-inch diameter fan driven by a turbine contained in the fan hub. The performance of the lift-fan simulator was measured in two ways: (1) the calculated momentum thrust of the fan and turbine (total thrust loading), and (2) the axial-force measured on a load cell force balance (axial-force loading). Tests were conducted over a wide range of crossflow velocities, corrected tip speeds, and wing angle of attack. A prediction modeling technique was developed to help in analyzing the performance characteristics of lift-fan simulators. A multiple linear regression analysis technique is presented which calculates prediction model equations for the dependent variables.

Yuska, J. A.↗

Experimental and numerical study of the effects of solution concentration and temperature on concrete under external sulfate attack

The work reports on an experimental programme, conducted to validate comprehensively our previously proposed coupled chemo-transport model for external sulfate attack on concrete. Specifically, the effects of the concentration of sulfate solution and temperature on the distribution of sulfate ions in concrete are experimentally investigated and used to demonstrate the accuracy of the modeling framework. Further, the profile of aluminate depletion and the leaching depth numerically are investigated. For all cases the model predictions are in good agreement with the experimental results, showing increases of the concentration of sulfate ions in concrete with higher concentrations of sulfate solution and higher temperatures. It is concluded that higher sulfate solution concentration and temperature enhance the processes involved in the external sulfate attack on concrete, namely diffusion of sulfate ions and their chemical reactions with concrete. It is found that these parameters affect the external sulfate attack predominantly via the chemical reaction process.

36 MATERIALS SCIENCE↗

Low-speed wind tunnel performance of high-speed counterrotation propellers at angle-of-attack

The low-speed aerodynamic performance characteristics of two advanced counterrotation pusher-propeller configurations with cruise design Mach numbers of 0.72 were investigated in the NASA Lewis 9- by 15-Foot Low-Speed Wind Tunnel. The tests were conducted at Mach number 0.20, which is representative of the aircraft take/off/landing flight regime. The investigation determined the effect of nonuniform inflow on the propeller performance characteristics for several blade angle settings and a range of rotational speeds. The inflow was varied by yawing the propeller mode to angle-of-attack by as much as plus or minus 16 degrees and by installing on the counterrotation propeller test rig near the propeller rotors a model simulator of an aircraft engine support pylon and fuselage. The results of the investigation indicated that the low-speed performance of the counterrotation propeller configurations near the take-off target operating points were reasonable and were fairly insensitive to changes in model angle-of-attack without the aircraft pylon/fuselage simulators installed on the propeller test rig. When the aircraft pylon/fuselage simulators were installed, small changes in propeller performance were seen at zero angle-of-attack, but fairly large changes in total power coefficient and very large changes of aft-to-forward-rotor torque ratio were produced when the propeller model was taken to angle-of-attack. The propeller net efficiency, though, was fairly insensitive to any changes in the propeller flowfield conditions near the take-off target operating points.

Hughes, Christopher E.↗

Noise of the SR-6 propeller model at 2 deg and 4 deg angles of attack

The noise generated by supersonic-tip-speed propellers creates a cabin noise problem for future airplanes powered by these propellers. Noise of a number of propeller models were measured in the NASA Lewis 8- by 6-Foot Wind Tunnel with flow parallel to the propeller axis. In flight, as a result of the induced upwash from the airplane wing, the propeller is at an angle of attack with respect to the incoming flow. Therefore, the 10-blade SR-6 propeller was operated at angle of attack to determine its noise behavior. Higher blade passage tones were observed for the propeller operating at angle of attack in a 0.6 axial Mach number flow. The noise increase was not symmetrical, with one wall of the wind tunnel showing a larger noise increase than the other wall. No noise increase was observed at angle of attack in a 0.8 axial Mach number flow. For this propeller the dominance of thickness noise, which does not increase with angle of attack, explains the lack of noise increase at the higher 0.8 Mach number.

Dittmar, J. H.↗

The hemisphere-cylinder in dynamic pitch-up motions

Laser-Doppler velocimetry and seven-hole probes were employed to map out the velocity and vorticity field along a plane downstream of a hemisphere-cylinder. Steady flow data were obtained over a fixed model at a range of angles of attack, as well as over a model pitching through ramp motions to a final angle of attack. Attention was focused on the dynamic development of induced vortex asymmetry. It was found that the wake develops first in a symmetric fashion and asymmetry is generated with some time delay.

Panzer, E. C.↗

Hypersonic Boundary-Layer Instabilities over Ogive-Cylinder Models

Computational investigations of an ogive-cylinder geometry with varying nosetips at zero degrees angle of attack are presented. The model geometry and conditions are selected to match experiments conducted in the Air Force Research Laboratory (AFRL) Mach 6 Ludwieg Tube. Five nosetips of interest were selected for the computational studies herein: two sharp ogives, two blunt ogives, and one hemispherical nosetip. Computations are performed at a freestream Reynolds number of 7.01 × 10 6 m -1 . Each sharp and blunt tip ogives had a 14 and 28 degree version for the tip angles. A cylindrical section follows the nosetip, resulting in a meter long model such as in the experiments. The laminar flow solutions are analyzed. The boundary-layer-edge properties and the velocity and temperature profiles are compared across streamwise locations aft of the ogive-cylinder junction. The blunt nosetips induce an entropy layer that envelopes the boundary-layer profiles. Modal stability analysis identifies most amplified frequencies corresponding to Mack’s second modes that agree with experimental results for the sharp tips. Similar to the experimental measurements based on wall-mounted pressure sensors, no unstable modes are found for the blunt models. Nonmodal analysis revealed a broadband set of disturbances present for the blunter tips, in agreement with experimental observations. Flow perturbation contours of most amplified planar and oblique disturbances are shown to qualitatively match wind tunnel Schlieren images, with a switch from rope-like to elongated structures, i.e., from high frequency Mack’s second modes to low frequency Mack’s first modes, as the nosetip angle is increased for the sharp tip, and from boundary-layer to entropy-layer disturbances as the bluntness is increased.

Boundary layer transition↗

Hypersonic Boundary-Layer Instabilities over Ogive-Cylinder Models

Computational investigations of an ogive-cylinder geometry with varying nosetips at zero degrees angle of attack are presented. The model geometry and conditions are selected to match experiments conducted in the Air Force Research Laboratory (AFRL) Mach 6 Ludwieg Tube. Five nosetips of interest were selected for the computational studies herein: two sharp ogives, two blunt ogives, and one hemispherical nosetip. Computations are performed at a freestream Reynolds number of 7.01 × 10 6 m -1 . Each sharp and blunt tip ogives had a 14 and 28 degree version for the tip angles. A cylindrical section follows the nosetip, resulting in a meter long model such as in the experiments. The laminar flow solutions are analyzed. The boundary-layer-edge properties and the velocity and temperature profiles are compared across streamwise locations aft of the ogive-cylinder junction. The blunt nosetips induce an entropy layer that envelopes the boundary-layer profiles. Modal stability analysis identifies most amplified frequencies corresponding to Mack’s second modes that agree with experimental results for the sharp tips. Similar to the experimental measurements based on wall-mounted pressure sensors, no unstable modes are found for the blunt models. Nonmodal analysis revealed a broadband set of disturbances present for the blunter tips, in agreement with experimental observations. Flow perturbation contours of most amplified planar and oblique disturbances are shown to qualitatively match wind tunnel Schlieren images, with a switch from rope-like to elongated structures, i.e., from high frequency Mack’s second modes to low frequency Mack’s first modes, as the nosetip angle is increased for the sharp tip, and from boundary-layer to entropy-layer disturbances as the bluntness is increased.

Boundary layer transition↗

Resilient Control of Networked Microgrids Using Vertical Federated Reinforcement Learning: Designs and Real-Time Test-Bed Validations

Improving system-level resiliency of networked microgrids against adversarial cyber-attacks is an important aspect in the current regime of increased inverter-based resources (IBRs). To achieve that, this paper contributes in designing a hierarchical control layer, in conjunction with the existing control layers, resilient to adversarial attack signals. Considering model complexities, unknown dynamical behaviors of IBRs, and privacy issues regarding data sharing in multi-party-owned microgrids, designing such a control layer is non-trivial. Here, to tackle these issues, a novel federated reinforcement learning (Fed-RL) method is proposed. To grasp the interconnected dynamics of networked microgrids, the paper develops Federated Soft Actor-Critic (FedSAC) algorithm following the vertical structure of implementing Fed-RL. Next, utilizing the OpenAI Gym interface, we built a custom set-up in GridLAB-D/HELICS co-simulation platform, named Resilient RL Co-simulation (ResRLCoSIM), to train the RL agents with IEEE 123-bus benchmark comprising 3 interconnected microgrids. Finally, the learned policies in the simulation are transferred to the real-time hardware-in-the-loop (HIL) test-bed developed using the high-fidelity Hypersim platform. Finally, experiments show that the simulator-trained RL controllers achieve desirable performance with the test-bed platform, validating the minimization of the sim-to-real gap.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Development of a Thin Film Primary Surface Heat Exchanger for Advanced Power Cycles

This project objective is to develop a high-temperature design upgrade for an existing primary surface heat exchanger so that the redesigned hardware is capable of operation in CO 2 at temperatures up to 1,510°F (821°C) and pressure differentials up to 130 psi (9 bar). The heat exchanger is proposed for use as a recuperator in an advanced low-pressure oxy-fuel Brayton cycle that is predicted to achieve over 50% thermodynamic efficiency, although the heat exchanger could also be used in other high-temperature, low-differential pressure cycles. This report describes the progress to date, which includes continuing work performed to select and test new candidate materials for the recuperator redesign, final mechanical and thermal performance analysis results of various redesign concepts, and the preliminary design of a test loop for the redesigned recuperator including a budgetary estimate for detailed test loop design, procurement, and test operation. A materials search was performed in order to investigate high-temperature properties of many candidate materials, including high-temperature strength and nickel content. These properties were used to rank the candidate materials, resulting in a reduced list of nine materials for corrosion testing. Multiple test rigs were considered and analyzed for short-term corrosion testing and Thermal Gravimetric Analysis (TGA) was selected as the most cost-effective option for evaluating corrosion resistance of the candidate materials. In addition, tantalum, niobium, and chromium coatings were identified as potential options for increased corrosion resistance. The test results show that many materials exhibit relatively low weight gain rates, and that niobium and tantalum coatings may improve corrosion resistance for many materials, while chromium coatings appear to oxidize and debond quickly. Metallurgical analysis of alloys was also performed, showing evidence of intergranular attack in 282 that may cause long-term reliability problems in CO 2 service at these temperatures. However, long-term testing in a flowing environment is recommended in order to understand accurately the severity of the attack. Detailed economic modeling of the existing air cycle recuperator and CO 2 cycle recuperator options was also completed, including costs for material, fabrication, fuel, maintenance, and operation. The analysis results show that the increased capital cost for high-temperature materials may be offset by higher cycle efficiencies, decreasing the overall lifetime cost of the system. The economic analysis also examines costs associated with increased pressure drop and material changes for two redesign options. These results show that, even with slightly reduced performance and/or higher material costs, the lifetime cost per energy production may still be reduced by over 12%. The existing recuperator design information was provided by Solar Turbines, Inc. via several models, drawings, and design handoff meetings. Multiple fluid/thermal and structural models were created in order to analyze critical recuperator performance and mechanical strength in critical areas throughout the redesign process. These models were analyzed for a baseline condition (consistent with current Mercury 50 operation) for validation purposes. Results are presented for heat transfer coefficients and pressure drops, matching well with the existing operational data. Simulation of higher-temperature CO 2 conditions was also performed, showing a slight expected increase in both heat transfer and pressure drop. Mechanical analysis results for critical areas on the cross-flow and counter-flow sheets have also been obtained for air and CO 2 cases. These results show similar stresses in both cases but significantly reduced safety factors for the CO 2 case due to reduced yield and creep rupture strengths of alloy 625 at the higher temperatures. A concept brainstorm session and initial down-selection were completed in order to identify promising redesign options for further analysis. Detailed analysis of all promising redesign options was performed via finite element and computational fluid dynamic simulations in order to characterize mechanical and thermal-fluid performance of each option. These options included material change, various sheet thickness configurations, pitch and phasing of cross-flow and counter-flow sheets, and separator sheets. The analysis results have identified two viable redesign options that maintain existing safety margins optimally through a material change to Haynes 282 and (A) sheet thickness increases of 40% on the counter-flow sheet and 75% on the hot side cross-flow corrugation sheet or (B) addition of a separator sheet in the counter-flow section while maintaining the original counter-flow sheet thickness and increasing the cross-flow corrugation sheet thickness by 90% to account for the increase in cell height. While both options satisfy mechanical stress constraints, the separator sheet design has a higher part count, slightly reduced heat transfer, and slightly higher pressure drop than the first option and is not preferred. Finally, several test loop concepts have been developed for different full-scale and reduced-scale recuperator testing options. For each option, various loop components, such as heat exchangers, valves, heaters, and compressors, were evaluated in an effort to maximize utilization of existing resources. All concepts utilize an existing 3-MW CO 2 compressor, heater, and loop coolers, but the concepts vary by incorporating different amounts of new equipment for achieving various flow rates (all concepts operate at design pressure and temperature). The third concept achieves a 1 kg/s test without purchasing any costly equipment (coolers, heaters, blowers, etc.). Since the stacked cell design of the recuperator results in the same flow conditions at each core cell (even for a reduced-scale test). Thus, test loop Concept #3 was selected for the preliminary design. This loop design is detailed within the report, culminating in a budgetary estimate of $1,013,000.00 for the detailed design, construction, commissioning, and operation of a high-temperature recuperator test loop.

03 NATURAL GAS↗

Degradation Mechanisms and Development of Protective Coatings for Thermal Energy Storage and High Temperature Fluid Containment Materials

This research addresses cost savings to achieve the SETO target of $15/kWh th for thermal energy storage and 6¢/kWh for levelized cost of energy. Next-generation solar power conversion systems require high-temperature, advanced fluids in the range of 600° to 900°C. The three major advanced fluid groups—supercritical CO 2 , liquid metal alloys, and molten salts—are very corrosive to common alloys used in vessels, heat exchangers, and piping at these temperatures. Understanding degradation mechanisms is essential for making recommendations on proper working conditions and suitable cost-effective coating materials for CSP applications at high temperatures. The implementation of the findings from this research will significantly reduce investment risk by increasing the lifetime of the CSP plant components. In the past, the majority of the hot corrosion evaluations have been performed for waste incinerators, gas turbine engines, and electric power generation (steam-generating equipment) applications for different materials, molten-salt systems, and coatings. Containment materials and resistant coatings for supercritical CO 2 , molten salts and liquid metal alloys have not being evaluated for CSP applications. We plan to understand the underlying degradation mechanisms to select protective approaches such as anodic passivation, cathodic protection, and coating designs.The novelty of the proposed research is the development of protective coatings and working conditions for materials in contact with high temperature TES and HTF. Current state-of-the-art materials and protection methods are non-existent. Novel approaches are: the use of graphite nanomaterials to enhance the non-wettability of the aggressive fluids with the coating; self-healing behavior of Si-coatings in liquid Al-Si alloys; anodic passivation in molten salts to protect metallic substrates and the modeling prediction of attack in liquid metal alloys.

14 SOLAR ENERGY↗

Wind-tunnel investigation at low speeds of a model of the Kestrel (XV-6A) vectored-trust V/STOL airplane

Longitudinal and lateral stability data were obtained with the model out of and in ground effect over a moving ground plane for a range of model angles of attack and sideslip at various thrust coefficients. These data were taken primarily at thrust coefficients which simulate transition speeds on the airplane between hover and 200 knots. Some data, however, represent the effect of thrust deflection at speeds up to 350 knots. Also presented are the effects of control-surface deflections and interference between the jets and free stream.

Margason, R. J.↗

Results of oil flow visualization tests of an 0.010-scale model (52-OT) of the space shuttle orbiter-tank mated and orbiter configurations in the AEDC VKF tunnel B (IA17B)

An 0.010-scale model of the space shuttle (orbiter-tank mated and orbiter configurations) was tested in the AEDC VKF Tunnel B to investigate aerodynamic flow patterns. The tests utilized oil flow techniques to visualize the flow patterns. Tunnel free stream Mach number was 7.95 and nominal unit Reynolds number was 3.7 million per foot. Model angle of attack was varied from -5 deg through 10 deg and angle of sideslip was 0 deg and 2 deg. Photographs of resulting oil flow patterns are presented.

Daileda, J. J.↗