Search NASA⌕ Search

SEARCH · Search NASA

Results for “ballistic performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS1961

ANALYSIS OF QUARTZ AND TEFLON SHIELDS FOR A PARTICULAR RE-ENTRY MISSION

The transient performance of ablation type heat protection shields is treated herein for the surface of a vehicle returning from outer space to the earth. The vehicle weighs 8640 kg, has a ballistic factor of 500 lb/ft2, re-enters with a speed of 11 km/sec at 120 km altitude, has a lift over drag ratio of -0.5, and is subjected to a maximum deceleration of 7.7 times the gravity constant. By use of well-known equations for the heat transfer and the mass transfer at a heated surface, a numerical calculation method is derived which, for the investigated ablation processes, yields exact transient solutions of the fundamental system of partial differential equations. The method is applied to various quartz shields and to one Teflon shield, which all evaporate so readily under the conditions of the problem at hand that practically no flow of molten shield material exists. The solutions also show comparatively small temperature changes parallel to the surface. The results show that the nose of the vehicle is cooled predominantly by the evaporation of the quartz or the Teflon; the rest of the vehicle's surface is cooled by radiation of the quartz or evaporation of the Teflon. The large mass transfer effects on the nose of the vehicle are detrimental since the resulting low surface temperatures prevent the radiative heat transfer out of the shield, which does not involve any mass loss, from being the desirable governing cooling factor.

ABLATING MATERIAL↗
NASA NTRS1980

Uranus mission options

Options for delivery of Uranus payloads are covered extensively. Launch energy charts are supplied for ballistic trajectories to Uranus for direct, Jupiter gravity-assist, and Saturn gravity-assist missions launching from 1982 to 1995. Both early reconnaissance (flyby) and orbiter missions are considered. Performance charts for low-thrust, Delta Vega, planetary gravity-assist, and combinations of these modes are plotted in terms of net orbited mass and trip time to Uranus. Discussion and illustration of the effects of the unique Uranus system oritentation on Uranus encounter geometry with trajectory arrival date is covered. Example mission designs are characterized for several delivery modes.

Wallace, R. A.↗
DOE OSTI2026

Measuring quasiparticle dynamics for particle impact reconstruction in a superconducting qubit chip

Quasiparticle poisoning following particle impacts poses a significant challenge to the development of fault-tolerant superconducting quantum computers, as a sudden excess of quasiparticles can simultaneously degrade the coherence of multiple qubits across large device arrays. In this work, we present a statistical analysis that models the time evolution of radiation-induced qubit energy relaxation through quasiparticle density dynamics. This study provides insight into quasiparticle loss processes by distinguishing between recombination and trapping decay channels and assessing their respective impact on qubit performance. We precisely measure quasiparticle recombination in multiple transmon qubits and uncover an unexpected dependence of qubit relaxation dynamics on deposited energy. By linking correlated relaxation events across qubits to ballistic phonon propagation, we introduce a statistical localization approach to extract the energy deposited in the substrate, which is in good agreement with Monte Carlo simulation. This work establishes the quantitative framework for using an arbitrary subset of superconducting transmon qubits in a QPU as energy-resolving witness particle detectors.

Celi, E. [Northwestern U.]↗
NASA NTRS2005

Fusion Ignition Rocket Engine with Ballistic Ablative Lithium Liner

Thermo-nuclear fusion may be the key to a high Isp, high specific power (low alpha) propulsion system. In a fusion system energy is liberated within, and imparted directly to, the propellant. In principle, this can overcome the performance limitations inherent in systems that require thermal power transfer across a material boundary, and/or multiple power conversion stages (NTR, NEP). A thermo-nuclear propulsion system, which attempts to overcome some of the problems inherent in the ORION concept, is described. A passive tapered liner is launched behind a vehicle, through a hole in a pusher-plate, that is connected to the vehicle by a shock-absorbing mechanism. A dense FRC plasmoid is then accelerated to high velocity (in excess of 1,000 km/s) and shot through the hole into the liner, when it has reached a given point down-range. The kinetic energy of the FRC is converted into thermal and magnetic-field energy, igniting a fusion bum in the magnetically confined plasma. The fusion reaction serves as an ignition source for the liner, which is made out of detonable materials. The energy liberated in this process is converted to thrust by the pusher-plate, as in the classic ORION concept. However with this concept, the vehicle does not carry a magazine of pre-fabricated pulse-units. A magnetic nozzle may also be used, in place of the pusher-plate. Estimates of the conditions needed to achieve a sufficient gain will be presented, along with a description of the driver characteristics. The incorporation of this concept into the propulsion system of a spacecraft will also be discussed.

Martin, Adam↗
DOE OSTI2023

Sound Velocity and Equation of State of Ballistic Gelatin by Brillouin Scattering

Brillouin scattering spectroscopy with diamond anvil cells was used by measuring the pressure dependence of the sound-relevant polymer material, glass-forming liquid, and H 2 O (water and ice VII) velocities of the material from ambient pressure to 12 GPa at room temperature. Measurements of 20%, 10%, and 4% gelatin solutions were performed. For comparison purposes, we also measured the pressure dependence of the sound velocity of animal tissue up to 10 GPa. We analyzed the Brillouin data using the Tait and Vinet equations of state. We discussed the possible influence of frequency dispersion on bulk modulus at low pressure. We compared the elastic moduli obtained for gelatin to those of several other polymers.

36 MATERIALS SCIENCE↗
NASA NTRS2000

A Characterization of the Terrestrial Environment of Kodiak Island, Alaska for the Design, Development and Operation of Launch Vehicles

A quantitative characterization of the terrestrial environment is an important component in the success of a launch vehicle program. Environmental factors such as winds, atmospheric thermodynamics, precipitation, fog, and cloud characteristics are among many parameters that must be accurately defined for flight success. The National Aeronautics and Space Administration (NASA) is currently coordinating weather support and performing analysis for the launch of a NASA payload from a new facility located at Kodiak Island, Alaska in late 2001 (NASA, 1999). Following the first launch from the Kodiak Launch Complex, an Air Force intercontinental ballistic missile on November 5, 1999, the site's developer, the Alaska Aerospace Development Corporation (AADC), is hoping to acquire a sizable share of the many launches that will occur over the next decade. One such customer is NASA, which is planning to launch the Vegetation Canopy Lidar satellite aboard an Athena I rocket, the first planned mission to low earth orbit from the new facility. To support this launch, a statistical model of the atmospheric and surface environment for Kodiak Island, AK has been produced from rawinsonde and surface-based meteorological observations for use as an input to future launch vehicle design and/or operations. In this study, the creation of a "reference atmosphere" from rawinsonde observations is described along with comparisons between the reference atmosphere and existing model representations for Kodiak. Meteorological conditions that might result in a delay on launch day (cloud cover, visibility, precipitation, etc.) are also explored and described through probabilities of launch by month and hour of day. This atmospheric "mission analysis" is also useful during the early stages of a vehicle program, when consideration of the climatic characteristics of a location can be factored into vehicle designs. To be most beneficial, terrestrial environment definitions should a) be available at the inception of the program and based on the desired operational performance of the launch vehicle, b) be issued under the signature of the program manager and be part of the controlled program definition and requirements documentation, and c) specify the terrestrial environment for all phases of activity including prelaunch, launch, ascent, on-orbit, decent, and landing. Since the beginning of the space era, NASA has utilized some of the most detailed assessments of the terrestrial climatic environment in design, development, and operations of both expendable and reusable launch vehicles.

Rawlins, Michael A.↗
NASA NTRS1986

Space Station gas-grain simulation facility - Application to exobiology

The technical issues involved in performing experiments on the behavior and properties of aerosols in a microgravity environment provided by the Space Station are reviewed. The displacement of a particle resulting from g-jitter for ballistic, Knudsen, and Stokes flow regimes is examined in detail, and the radiation, acoustic, electrostatic, and electromagnetic mechanisms for the control of this motion are described. The simulation of organic haze production on Titan has been selected as an example experiment for detailed study. The purpose of this experiment was to simulate the photolysis of methane and the subsequent formation of the organic haze particles in the Titan upper atmosphere.

Mckay, C. P.↗
NASA NTRS1990

Survivability characteristics of composite compression structure

Test and evaluation was performed to determine the compression residual capability of graphite reinforced composite panels following perforation by high-velocity fragments representative of combat threats. Assessments were made of the size of the ballistic damage, the effect of applied compression load at impact, damage growth during cyclic loading and residual static strength. Several fiber/matrix systems were investigated including high-strain fibers, tough epoxies, and APC-2 thermoplastic. Additionally, several laminate configurations were evaluated including hard and soft laminates and the incorporation of buffer strips and stitching for improved damage resistance of tolerance. Both panels (12 x 20-inches) and full scale box-beam components were tested to assure scalability of results. The evaluation generally showed small differences in the responses of the material systems tested. The soft laminate configurations with concentrated reinforcement exhibited the highest residual strength. Ballistic damage did not grow or increase in severity as a result of cyclic loading, and the effects of applied load at impact were not significant under the conditions tested.

Avery, John G.↗
NASA NTRS2005

Uncertainty Considerations for Ballistic Limit Equations

The overall risk for any spacecraft system is typically determined using a Probabilistic Risk Assessment (PRA). A PRA attempts to determine the overall risk associated with a particular mission by factoring in all known risks (and their corresponding uncertainties, if known) to the spacecraft during its mission. The threat to mission and human life posed by the mircro-meteoroid & orbital debris (MMOD) environment is one of the risks. NASA uses the BUMPER II program to provide point estimate predictions of MMOD risk for the Space Shuttle and the International Space Station. However, BUMPER II does not provide uncertainty bounds or confidence intervals for its predictions. With so many uncertainties believed to be present in the models used within BUMPER II, providing uncertainty bounds with BUMPER II results would appear to be essential to properly evaluating its predictions of MMOD risk. The uncertainties in BUMPER II come primarily from three areas: damage prediction/ballistic limit equations, environment models, and failure criteria definitions. In order to quantify the overall uncertainty bounds on MMOD risk predictions, the uncertainties in these three areas must be identified. In this paper, possible approaches through which uncertainty bounds can be developed for the various damage prediction and ballistic limit equations encoded within the shuttle and station versions of BUMPER II are presented and discussed. We begin the paper with a review of the current approaches used by NASA to perform a PRA for the Space Shuttle and the International Space Station, followed by a review of the results of a recent sensitivity analysis performed by NASA using the shuttle version of the BUMPER II code. Following a discussion of the various equations that are encoded in BUMPER II, we propose several possible approaches for establishing uncertainty bounds for the equations within BUMPER II. We conclude with an evaluation of these approaches and present a recommendation regarding which of them would be the most appropriate to follow.

Schonberg, W. P.↗
NASA NTRS2019

Materials and Processes for New Propulsion Systems with Reduced Environmental Impact

Aeronautics research at NASA Glenn Research Center includes development, characterization and modeling of high temperature, lightweight materials and fabrication processes for aircraft propulsion systems with increased efficiency and reduced emissions, fuel burn and noise. Current propulsion materials research includes Ceramic Matrix Composites and Environmental Barrier Coatings, Polymer Matrix Composites and Additive Manufacturing processes. This presentation will summarize recent progress and plans in these areas. Ceramic Matrix Composites for Turbine Components: As part of NASA's Aeronautics research, Glenn Research Center has developed Ceramic Matrix Composites for 2700 degrees Fahrenheit turbine engine applications in the next generation of ultra-efficient aircraft. In this presentation, the development of advanced fiber and matrix constituents that enabled this advancement will be reviewed, and characterization of the resulting improvements in mechanical properties and durability will be summarized. Progress toward the development and validation of models predicting the effects of the engine environment on durability of Ceramic Matrix Composites and Environmental Barrier Coatings will be summarized. Progress and plans for collaborative research with industry and other government agencies will be reviewed. Polymer Matrix Composites for Powertrain and Impact Protection: A lightweight, hybrid polymer matrix composite/steel gear concept for rotorcraft power transmission applications was evaluated at realistic speed, torque, and power conditions. Dynamic testing was performed at 5000 horsepower and 5400 revolutions per minute with no performance degradation. Test results demonstrated the potential of hybrid composite / metal gears to reduce gear weight by approximately 15 percent, enabling the implementation of multi-speed drive systems, which would otherwise have a weight penalty, for increased speed and efficiency. Results of post-test inspection and endurance tests will be presented. Separately, ballistic impact tests demonstrated improved damage tolerance in polymer matrix composites by incorporating lightweight, thermoplastic veil materials between selected composite plies during the composite fabrication process. Results of impact tests and post-test inspection will be presented. Additive Manufacturing for Electric Propulsion: Additive Manufacturing processes offer the potential to fabricate new, high power density electric motor designs with complex geometries, multi-material components and optimally designed components that would not be feasible with traditional manufacturing processes. High performance stator components using advanced 3-phase conductive coils were fabricated using direct printing with optimized silver pastes. Additional additive manufacturing methods are being used to fabricate rotors and motor housing components. Systems studies show that the higher performance and lower weight motors offer improved energy efficiency and reduced emissions. Improvements to motor performance resulting from optimized materials and component designs will be presented.

Additive Manufacturing↗
NASA NTRS2019

Observations of Non-Spherical, Graphite-Epoxy Projectiles Impacting a Thermally-Insulated, Double-Wall Shield

The DebriSat hypervelocity impact experiment, performed at the Arnold Engineering Development Center (U.S.A.F. Arnold Air Force Base), is intended to update the catastrophic break-up models for modern satellites. To this end, the DebrisSat was built with many modern materials including structural panels of carbon-fiber, reinforced polymer (CFRP). Subsequent to the experiment, fragments of the DebrisSat have been extracted from porous, catcher panels used to gather the debris from the impact event. Thus far, one of the key observations from the collected fragments is that CFRP represents a large fraction of the fragments and that these fragments tend to be thin, flake-like structures or long, needle-like structures; whereas, debris with nearly equal dimensions is less prevalent. As current ballistic-limit models are all developed based upon spherical impacting particles, the experiment has pointed to a missing component in the current approach that must be considered. To begin to understand the implications of this observation, simulations like those shown in Fig. 1 have been performed using cylindrical structures at a representative orbital speed into an externally-insulated, double-wall shield that is representative of shielding of International-Space-Station-visiting vehicles. These simulations have been performed for normal impacts to the surface with three different angles-of-attack (AOA) to capture the effect on the shield performance. This paper documents the simulated shield and the models developed to study the effect of non-spherical fragments, as well as, derives the critical characteristics of CFRP impacting particles for the selected shield as shown in Fig. 2. To assist with the design of the updated debris models, this work summarizes the simulated results into a deployable form for evaluating the relative importance of fragment structures.

Miller, Joshua E.↗
NASA NTRS1974

Ballistic mode Mercury orbiter mission opportunity handbook extension

Interplanetary trajectory characteristics are presented, for Venus swingbys to Mercury, where multiple revolutions about the Sun are permitted. Additional consideration is given to the use of multiple Venus swingbys and/or to midcourse, near perilhelion, propulsive maneuvers to improve the performance of the mission as measured in terms of payload in Mercury orbit. Missions in 1980, 1983, 1985 and 1988 were analyzed with navigation results also developed. An exploratory investigation established the availability of low energy mission opportunities in 1991, 1994, 1996 and 1999.

Hollenbeck, G. R.↗
NASA NTRS2013

Thermal and Structural Performance of Woven Carbon Cloth For Adaptive Deployable Entry and Placement Technology

Arcjet testing and analysis of a three-dimensional (3D) woven carbon fabric has shown that it can be used as a thermal protection system and as a load bearing structural component for a low ballistic coefficient hypersonic decelerator called ADEPT (Adaptive Deployable Entry and Placement Technology). Results of arcjet tests proved that the 3D woven carbon fabric can withstand flight-like heating while under flight-like biaxial mechanical loads representative of those encountered during shallow entry flight path angles into the atmosphere of Venus. Importantly, the arcjet test results have been used to extend a preliminary material thermal response model based on previous testing of the same 3D woven carbon fabric under uni-axial mechanical loading.

Carbon fabric↗
DOE OSTI2023

Anomalous electronic transport in high-mobility Corbino rings

We report low-temperature electronic transport measurements performed in two multi-terminal Corbino samples formed in GaAs/Al-GaAs two-dimensional electron gases (2DEG) with both ultra-high electron mobility ( ≳ 20 × 10 6 cm 2 / Vs) and with distinct electron density of 1.7 and 3.6 × 10 11 cm -2 . In both Corbino samples, a non-monotonic behavior is observed in the temperature dependence of the resistance below 1 K. Surprisingly, a sharp decrease in resistance is observed with increasing temperature in the sample with lower electron density, whereas an opposite behavior is observed in the sample with higher density. To investigate further, transport measurements were performed in large van der Pauw samples having identical heterostructures, and as expected they exhibit resistivity that is monotonic with temperature. Finally, we discuss the results in terms of various lengthscales leading to ballistic and hydrodynamic electronic transport, as well as a possible Gurzhi effect.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
NASA NTRS1971

Mars surface sample return missions via solar electric propulsion

The characteristics and capabilities are described of solar electric propulsion (SEP) for performing Mars Surface Sample Return (MSSR) missions. The scope of the study emphasizes trajectory/payload analysis and the comparison of mission/system tradeoff options. The MSSR mission is examined only for the 1981-82 launch opportunity. Several other study constraints which bear directly on the results obtained are: (1) return samples in the range 5-25 kg, (2) use of lifting (offset C.G.) atmospheric entry at Mars which allows a low ratio (1.25) of entry weight to landed weight, and (3) rendezvous and docking in Mars orbit. Major results of the study are presented as performance curves of earth departure mass versus sample size for a number of different mission/system options. These options represent a spectrum of trip time, launch vehicle capability, combinations of low-thrust and ballistic maneuvers, chemical retro type, and earth recovery mode.

Spadoni, D. J.↗
NASA NTRS1973

Thermoelectric Outer Planets Spacecraft (TOPS)

The research and advanced development work is reported on a ballistic-mode, outer planet spacecraft using radioisotope thermoelectric generator (RTG) power. The Thermoelectric Outer Planet Spacecraft (TOPS) project was established to provide the advanced systems technology that would allow the realistic estimates of performance, cost, reliability, and scheduling that are required for an actual flight mission. A system design of the complete RTG-powered outer planet spacecraft was made; major technical innovations of certain hardware elements were designed, developed, and tested; and reliability and quality assurance concepts were developed for long-life requirements. At the conclusion of its active phase, the TOPS Project reached its principal objectives: a development and experience base was established for project definition, and for estimating cost, performance, and reliability; an understanding of system and subsystem capabilities for successful outer planets missions was achieved. The system design answered long-life requirements with massive redundancy, controlled by on-board analysis of spacecraft performance data.

Source record↗
NASA NTRS1993

BMDO electric space-propulsion program

Electric propulsion (EP) applications being considered include: orbit insertion, orbit repositioning, station keeping, and elusive maneuvering. Typically, 1 to 5 kW are available for EP. A class of thrusters, the Hall-effect thrusters, is extensively researched, developed and flown by Russia. These thrusters, using xenon propellant, perform reliably, e.g., at 1.35 kW, 600 s specific impulse, 50 percent efficiency and greater than 2000 hr life. This specific impulse and efficiency combination is superior to the present arcjets for several Ballistic Missile Defense Organization (BMDO) applications. Three versions of the Hall thrusters are part of the experimental evaluation. Since today's goals are within reach of available thrusters and power sources, emphasis is being placed on such topics as: thruster lifetime, spacecraft interactions, electromagnetic interference, and erosion product deposition. Facilities in U.S. laboratories are being specially configured to achieve these goals.

Caveny, Leonard H.↗
NASA NTRS1980

Design study of prestressed rotor spar concept

Studies on the Bell Helicopter 540 Rotor System of the AH-1G helicopter were performed. The stiffness, mass and geometric configurations of the Bell blade were matched to give a dynamically similar prestressed composite blade. A multi-tube, prestressed composite spar blade configuration was designed for superior ballistic survivability at low life cycle cost. The composite spar prestresses, imparted during fabrication, are chosen to maintain compression in the high strength cryogenically stretchformed 304-L stainless steel liner and tension in the overwrapped HTS graphite fibers under operating loads. This prestressing results in greatly improved crack propagation and fatigue resistance as well as enhanced fiber stiffness properties. Advantages projected for the prestressed composite rotor spar concept include increased operational life and improved ballistic survivability at low life cycle cost.

Gleich, D.↗