Search NASA⌕ Search

SEARCH · Search NASA

Results for “bearings”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Unbalance response of a two spool gas turbine engine with squeeze film bearings

This paper presents a dynamic analysis of a two-spool gas turbine helicopter engine incorporating intershaft rolling element bearings between the gas generator and power turbine rotors. The analysis includes the nonlinear effects of a squeeze film bearing incorporated on the gas generator rotor. The analysis includes critical speeds and forced response of the system and indicates that substantial dynamic loads may be imposed on the intershaft bearings and main bearing supports with an improperly designed squeeze film bearing. A comparison of theoretical and experimental gas generator rotor response is presented illustrating the nonlinear characteristics of the squeeze film bearing. It was found that large intershaft bearing forces may occur even though the engine is not operating at a resonant condition.

Gunter, E. J.↗
NASA NTRS1982

Past Performance analysis of HPOTP bearings

The past performance analysis conducted on three High Pressure Oxygen Turbopump (HPOTP) bearings from the Space Shuttle Main Engine is presented. Metallurgical analysis of failed bearing balls and races, and wear track and crack configuration analyses were carried out. In addition, one bearing was tested in laboratory at very high axial loads. The results showed that the cracks were surface initiated and propagated into subsurface locations at relatively small angles. Subsurface cracks were much more extensive than was appeared on the surface. The location of major cracks in the races corresponded to high radial loads rather than high axial loads. There was evidence to suggest that the inner races were heated to elevated temperatures. A failure scenario was developed based on the above findings. According to this scenario the HPOTP bearings are heated by a combination of high loads and high coefficient of friction (poor lubrication). Different methods of extending the HPOTP bearing life are also discussed. These include reduction of axial loads, improvements in bearing design, lubrication and cooling, and use of improved bearing materials.

Bhat, B. N.↗
NASA NTRS1982

Evaluation of bearing mounting design and excessive wear phenomena

The effect of bearing thermal growth on the effectiveness of the bearing preload springs on the space shuttle main engine high pressure oxygen turbopump (SSME HPTOP) were examined. The SSME HPTOP turbine end bearings, preload spring, and bearing mounting design were evaluated relative to spalling, excessive ball wear, possible thermal problems, and cage delamination. The magnitude of the thermal stresses required to cause high levels of ball wear were calculated. Plots of maximum sheer stress and maximum reversing shear versus the axial load for the 57 mm SSME HPTOP bearing were created. A plot of the bearing thermal growth versus preload spring deflection was generated. It was determined that metallic wear, rather than thermal growth, caused enlargement of the contact zone between ball and races, that high fatigue-inducing shear stresses are generated under increased loads, and that at temperatures between 100 and 150 deg C, the springs bottom out and very high loads are developed in the bearing. Allowance for adequate spring movement after assembly is recommended.

Kannel, J. W.↗
NASA NTRS1981

Endurance tests with large-bore tapered-roller bearings to 2.2 million DN

Endurance life tests were run with standard-design bearings of vacuum-melted AISI 4320 and CBS-1000M at 12,500 rpm, and high-speed bearings of CBS-1000M and trough-hardened AISI M-50 at 18,500 rpm. Both sets of bearings were of 120.65 mm bore-tapered roller type, and were run under heavy combined radial and thrust loads until either fatigue failure or a preset cutoff time of 1100 hours was reached. It was found that: (1) the CBS-1000M standard-design bearings ran to a 10% life approximately six times that of the rated catalog life; (2) twelve identical bearings of AISI 4320 ran to ten times rated catalog life without failure; (3) cracking and fracture of the cones of AISI M-50 high-speed design bearings occurred at 18,500 rpm due to high tensile hoop stresses; and (4) four CBS 1000M high-speed bearings ran to twenty-four times rated catalog life without spalling, cracking or fracture failures.

Parker, R. J.↗
NASA NTRS1982

Determination of ball bearing dynamic stiffness

The dynamic radial stiffness characteristics of rolling element bearings are currently determined by analytical methods that have not been experimentally verified. These bearing data are vital to rotating machinery design integrity because accurate critical speeds and rotor stability predictions are highly dependent on the bearing stiffness. A tester was designed capable of controlling the bearing axial preload, speed, and rotor unbalance. The rotor and support structures were constructed to permit critical speeds that are predominantly determined by a 57 mm test bearing. A curve of calculated critical speed versus stiffness was used to determine the actual bearing stiffness from the empirical data. The results of extensive testing are used to verify analytical predictions, increase confidence in existing bearing computer programs, and to serve as a data base for efforts to correct these programs.

Beatty, R. F.↗
NASA NTRS1983

Lubrication of 35-millimeter-bore ball bearings of several designs to 2.5 million DN

Parametric tests were conducted with 35mm bore, angular contact ball bearings with either a single or double outer and guided cage. The bearings were either lubricated by oil jets or employed inner ring lubrication. Outer ring cooling was added in selected tests. Lubricant flow to the bearing ranged from 300 to 1900 cc/min. All bearings were successfully run at speeds to 2.5 million DN. Increasing the lubricant flow decreased bearing ring temperatures but increased bearing power lines. The power loss and race temperatures of a jet lubricated with double outer land guided cage were always higher than those of the single land guided design at similar test conditions. The lowest bearing operating temperatures were achieved when inner ring lubrication and outer ring cooling were combined. It is found that cage slip of a double outer land guided cage is approximately twice that of a single outer land guided cage.

Schuller, F. T.↗
NASA NTRS1983

The performance and application of high speed long life LH2 hybrid bearings for reusable rocket engine turbomachinery

Data are presented for two different experimental programs which were conducted to investigate the characteristics of a hybrid (hydrostatic/ball) bearing operating in liquid hydrogen. The same bearing design was used in both programs. Analytical predictions were made of the bearing characteristics and are compared with the experimental results when possible. The first program used a bearing tester to determine the steady state, transient, and cyclic life characteristics of the bearing over a wide range of operating conditions. The second program demonstrated the feasibility of applying hybrid bearings to an actual high speed turbopump by retrofitting and then testing an existing liquid hydrogen turbopump with the bearings.

Hannum, N. P.↗
NASA NTRS1983

Rolling-Element Bearings

Rolling element bearings are a precision, yet simple, machine element of great utility. A brief history of rolling element bearings is reviewed and the type of rolling element bearings, their geometry and kinematics, as well as the materials they are made from and the manufacturing processes they involve are described. Unloaded and unlubricated rolling element bearings, loaded but unlubricated rolling element bearings and loaded and lubricated rolling element bearings are considered. The recognition and understanding of elastohydrodynamic lubrication covered, represents one of the major development in rolling element bearings.

Hamrock, B. J.↗
NASA NTRS1982

Advances in high-speed rolling-element bearings

The research program begun by NASA in 1959 in order to investigate the projected temperature and speed requirements of large bore ball and roller bearings was expanded in the 1970s to include tapered roller and small bore bearings. In the course of the program, bearing speeds as high as 3 million DN and 2.4 million DN, respectively, were achieved for ball and tapered roller bearings with fatigue lives exceeding those common in commercial aircraft. The computer analysis of rolling element bearings operation have yielded reasonably accurate performance predictions for speeds up to 3 million DN. It was found that under-race bearing lubrication improved operational performance over that achieved with conventional jet lubrication methods at high bearing speeds.

Zaretsky, E. V.↗
NASA NTRS1983

The performance and application of high speed long life LH2 hybrid bearings for reusable rocket engine turbomachinery

Data are presented for two different experimental programs which were conducted to investigate the characteristics of a hybrid (hydrostatic/ball) bearing operating in liquid hydrogen. The same bearing design was used in both programs. Analytical predictions were made of the bearing characteristics and are compared with the experimental results when possible. The first program used a bearing tester to determine the steady state, transient, and cyclic life characteristics of the bearing over a wide range of operating conditions. The second program demonstrated the feasibility of applying hybrid bearings to an actual high speed turbopump by retrofitting and then testing an existing liquid hydrogen turbopump with the bearings.

Hannum, N. P.↗
NASA NTRS1984

Comparison of predicted and experimental thermal performance of angular-contact ball bearings

Predicted bearing heat generation and bearing temperature were verified by experimental data for ball bearings over a range of sizes, shaft speeds, and lubricant flow rates. The computer program Shaberth requires, as input, a factor which describes the air-oil mixture in the bearing cavity for calculation of the ball drag contribution to bearing heat generation. An equation for this lubricant percent volume in the bearing cavity was derived and appears to be valid over the range of test conditions including bearing bore sizes from 35 to 167 mm and shaft speeds from 1.0 to 3.0 million DN.

Parker, R. J.↗
NASA NTRS1985

Design and lubrication of high-speed rolling-element bearings

The speed capability of rolling element bearings has increased from speeds of less than two million DN to speeds of three million DN. The life and reliability of these bearings also increased where they are equal to, or greater than, those of bearings with limited speed capability. Design parameters must be carefully chosen and optimized based upon sophisticated bearing computer programs. Material and lubricant selection must be integrated into the bearing design. Bearing thermal management must be implemented through proper lubrication and cooling. Parameters which can be used to design, specify, and lubricate high speed bearings are discussed.

Zaretsky, E. V.↗
NASA NTRS1986

Selection of rolling-element bearing steels for long-life application

Nearly four decades of research in bearing steel metallurgy and processing have resulted in improvements in bearing life by a factor of 100 over that obtained in the early 1940's. For critical applications such as aircraft, these improvements have resulted in longer lived, more reliable commercial aircraft engines. Material factors such as hardness, retained austenite, grain size and carbide size, number, and area can influence rolling-element fatigue life. Bearing steel processing such as double vacuum melting can have a greater efect on bearing life than material chemistry. The selection and specification of a bearing steel is dependent on the integration of all these considerations into the bearing design and application. The paper reviews rolling-element fatigue data and analysis which can enable the engineer or metallurgist to select a rolling-element bearing steel for critical applications where long life is required.

Zaretsky, E. V.↗
NASA NTRS1986

MSFC cryogenic turbopump bearing tester results and analysis

A full scale High Pressure Oxidizer Turbopump (HPOTP) bearing tester has been developed, and an existing test stand modified, to simulate turbopump operating conditions for Space Shuttle Main Engine HPOTP design. Following a description of test facilities and procedures, design certification and calibration tests, and tests at a moderate axial load, are discussed. Results show that a bearing life of about 4500 seconds is comparable to the life experienced in the engine pump at nominal high power level operating conditions, and that although increased coolant flow increased fluid viscous work and bearing loads, a net decrease in bearing temperature was noted. Increased coolant flow is found to improve bearing cooling for marginal conditions, and bearing temperatures are shown to become more sensitive to coolant flow as shaft speed is increased. For the 6.4 lbs/s test conditions, the heat generated in a bearing pair is determined to be about 67 percent viscous work and 33 percent contact friction.

Dolan, F. J.↗
NASA NTRS1989

Selection of rolling-element bearing steels for long-life applications

Nearly four decades of research in bearing steel metallurgy and processing have resulted in improvements in bearing life by a factor of 100 over that obtained in the early 1940s. For critical applications such as aircraft, these improvements have resulted in longer lived, more reliable commercial aircraft engines. Material factors such as hardness, retained austenite, grain size and carbide size, number, and area can influence rolling-element fatigue life. Bearing steel processing such as double vacuum melting can have a greater effect on bearing life than material chemistry. The selection and specification of a bearing steel is dependent on the integration of all these considerations into the bearing design and application. The paper reviews rolling-element fatigue data and analysis which can enable the engineer or metallurgist to select a rolling-element bearing steel for critical applications where long life is required.

Zaretsky, Erwin V.↗
NASA NTRS1988

Tribological composition optimization of chromium-carbide-based solid lubricant coatings for foil gas bearings at temperatures to 650 C

The determination of the tribilogically optimum composition of chromium-carbide-based solid lubricant coatings using a foil gas bearing test apparatus is described. The coatings contain a wear resistant chromium carbide `base stock' with the lubricant additives silver and BaF2-CaF2 eutectic. The coating composition is optimized for air-lubricated foil gas bearings at temperatures ranging from 25 to 650 C. The various compositions were prepared by powder blending, then plasma sprayed onto Inconel 718 test journals and diamond ground to the desired coating thickness and surface finish. The journals were operated against preoxidized Ni-Cr alloy foils, and the test bearings were subjected to repeated start-stop cycles under a bearing unit of 14 kPa. Sliding contact between the coated journal and the smooth foil occurs during bearing start-up before lift-off or hydrodynamic lubrication by the air film and during bearing coast-down. The bearings were tested for 9000 start-stop cycles or until specimen reached a predetermined failure level.

Dellacorte, Christopher↗
NASA NTRS1988

Cryogenic, high speed, turbopump bearing cooling requirements

Although the Space Shuttle Main Engine (SSME) has repeatedly demonstrated the capability to perform during launch, the High Pressure Oxidizer Turbopump (HPOTP) main shaft bearings have not met their 7.5 hour life requirement. A tester is being employed to provide the capability of subjecting full scale bearings and seals to speeds, loads, propellants, temperatures, and pressures which simulate engine operating conditions. The tester design permits much more elaborate instrumentation and diagnostics than could be accommodated in an SSME turbopump. Tests were made to demonstrate the facilities; and the devices' capabilities, to verify the instruments in its operating environment and to establish a performance baseline for the flight type SSME HPOTP Turbine Bearing design. Bearing performance data from tests are being utilized to generate: (1) a high speed, cryogenic turbopump bearing computer mechanical model, and (2) a much improved, very detailed thermal model to better understand bearing internal operating conditions. Parametric tests were also made to determine the effects of speed, axial loads, coolant flow rate, and surface finish degradation on bearing performance.

Dolan, Fred J.↗
NASA NTRS1988

Pratt and Whitney cryogenic turbopump bearing experience

Successful, reusable bearings require lubrication, traditionally, a transfer film from sacrificial cage wear. Early testing included materials screening programs to identify suitable cryogenic cage materials. A specially developed element tester that simulated the function of a ball bearing cage was used. Suitable materials must provide lubrication with an acceptably low wear rate, without abrading contacting surfaces. The most promising materials were tested in full scale bearings at speeds up to 4 MDN. Teflon, filled with 40 percent bronze powder, was the best performing material. A variety of bearings were designed and successfully tested in LH2 and LOX. Bearings with bronze filled Teflon cages were successfully tested for 150 hrs. In overload tests, the same design was tested for 5 hrs at maximum Hertz stresses above 450 ksi and an additional 5 hrs with a maximum Hertz stress exceeding 500 ksi. Four bearings were tested in LOX for 25 hrs, with a maximum time per bearing of 10 hrs.

Poole, W. E.↗