Search NASA⌕ Search

SEARCH · Search NASA

Results for “composite optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

Stress Analysis and Structural Optimization of a Three-Layer Composite Cladding Tube Under Thermo-Mechanical Loads

A general solution for the stress and strain fields in a three-layer composite tube subjected to internal and external pressures and temperature changes is first derived using thermo-elasticity. The material in each layer is treated as orthotropic, and the composite tube is regarded to be in a generalized plane strain state. A three-layer ZRY4-SiCf/SiCSiC composite cladding tube under a combined pressure and thermal loading is then analyzed and optimized by applying the general solution. The effects of temperature changes, applied pressures, and layer thickness on the mechanical behavior of the tube are quantitatively studied. The von Mises failure criterion for isotropic materials and the Tsai-Wu's failure theory for composites are used, respectively, to predict the failure behavior of the monolithic ZRY4 (i.e., Zircaloy-4) inner layer and SiC outer layer and the composite SiCf/SiC core layer of the three-layer tube. The numerical results reveal that the maximum radial and circumferential stresses in each layer always occur on the bonding surfaces. By adjusting the thickness of each layer, the effective stress in the three-layer cladding tube under the prescribed thermal-mechanical loading can be changed, thereby making it possible to optimally design the cladding tube.

36 MATERIALS SCIENCE↗

DPC Cement Filler Development (Progress Report)

The fillers research and development (R&D) program, mostly experimental, is part of a broader R&D program that includes new process modeling and performance assessment of criticality effects and the overall importance of criticality to repository performance (consequence screening). A literature research and consultation effort with experts by Hardin and Brady (2018) identified several potentially effective and workable filler materials including cements (primarily phosphate based), moltenmetal alloys, and low-temperature glasses. Filler attributes were defined, and the preliminary lists were compared qualitatively. Further comparative analysis will be done (e.g., cost estimates) after experimental screening has narrowed the list of alternatives. The following cement filler compositions were selected for experimental development work and accelerated testing in FY20: Aluminum phosphate cements (APCs); more specifically aluminum oxide / aluminum phosphate (Al 2 O 3 / AlPO 4 ) cements in which Al 2 O 3 serves as the filler material bound by an AlPO 4 binder formed by the reaction of Al 2 O 3 with H 3 PO 4 ; Calcium phosphate cements (CPCs); more specifically composed of pure or nearly pure hydroxyapatite or HAP (Ca 5 (PO 4 ) 3 (OH)); Wollastonite phosphate cements (WPC), specifically wollastonite and aluminum or calcium aluminum phosphates in which CaSiO 3 serves as the filler material and the phosphate serves as the binder. The FY20 effort focused on the optimization of compositions and subsequent processing of these three materials to achieve dense and well-consolidated monolithic samples with 30 to 40% porosity and permeabilities of 1 millidarcy. At the close of this progress report the aluminum phosphate cements (APCs) and the wollastonite phosphate cements (WPCs) appear to show the most promise for continued development. Less progress has been made with the calcium phosphate cements (CPCs); their slurry viscosities are high (and difficult to measure) and they exhibit relatively short cure times of 2 to 3 hours with concomitant and excessive volatile (e.g. CO 2 ) generation.

36 MATERIALS SCIENCE↗

Effect of Mixed Working Fluid Composition on Binary Cycle Condenser Heat Transfer Coefficients

Effect of Mixed Working Fluid Composition on Binary Cycle Condenser Heat Transfer Coefficients Dan Wendt, Greg Mines Idaho National Laboratory The use of mixed working fluids in binary power plants can provide significant increases in plant performance, provided the heat exchangers are designed to take advantage of these fluids non-isothermal phase changes. In the 1980's testing was conducted at DOE's Heat Cycle Research Facility (HCRF) where mixtures of different compositions were vaporized at supercritical pressures and then condensed. This testing had focused on using the data collected to verify that Heat Transfer Research Incorporated (HTRI) codes were suitable for the design of heat exchangers that could be used with mixtures. The HCRF data includes mixture compositions varying from 0% to 40% isopentane and condenser tube orientations of 15{sup o}, 60{sup o}, and 90{sup o} from horizontal. Testing was performed over a range of working fluid and cooling fluid conditions. Though the condenser used in this testing was water cooled, the working fluid condensation occurred on the tube-side of the heat exchanger. This tube-side condensation is analogous to that in an air-cooled condenser. Tube-side condensing heat transfer coefficient information gleaned from the HCRF testing is used in this study to assess the suitability of air-cooled condenser designs for use with mixtures. Results of an air-cooled binary plant process model performed with Aspen Plus indicate that that the optimal mixture composition (producing the maximum net power for the scenario considered) is within the range of compositions for which data exist. The HCRF data is used to assess the impact of composition, tube orientation, and process parameters on the condensing heat transfer coefficients. The sensitivity of the condensing coefficients to these factors is evaluated and the suitability of air-cooled condenser designs with mixtures is assessed. This paper summarizes the evaluation of the HCRF data and discusses the next steps in the project evaluation of air-cooled condenser designs that can take advantage of the performance gains possible with these fluids.

15 GEOTHERMAL ENERGY↗

Boosting Big National Lab Data

Introduction: Big data. Love it or hate it, solving the world’s most intractable problems requires the ability to make sense of huge and complex sets of data and do it quickly. Speeding up the process – from hours to minutes or from weeks to days – is key to our success. One major source of such big data are physical experiments. As many will know, these physical experiments are commonly used to solve challenges in fields such as energy security, manufacturing, medicine, pharmacology, environmental protection and national security. Experiments use different instruments and sensor types to research for example the validity of new drugs, the base cause for diseases, more efficient energy sources, new materials for every day goods, effective methods for environmental cleanup, the optimal ingredients composition for chocolate or determine how to preserve valuable antics. This is done by experimentally determining the structure, properties and processes that govern biological systems, chemical processes and materials. The speed and quality at which we can acquire new insights from experiments directly influences the rate of scientific progress, industrial innovation and competitiveness. And gaining new groundbreaking insights, faster, is key to the economic success of our nations. Recent years have seen incredible advances in sensor technologies, from house size detector systems in large experiments such as the Large Hadron Collider and the ‘Eye of Gaia’ billion pixel camera detector to high throughput genome sequencing. These developments have led to an exponential increase in data volumes, rates and variety produced by instruments used for experimental work. This increase is coinciding with a need to analyze the experimental results at the time they are collected. This speed is required to optimize the data taking and quality, and also to enable new adaptive experiments, where the sample is manipulated as it is observed, e.g. a substance is injected into a tissue sample and the gradual effect is observed as more of the substance is injected, providing better insights into the natural processes that are occurring, as well as result driven sampling adjustment to capture particularly interesting features --- as they emerge. The Department of Energy’s Pacific Northwest National Laboratory (PNNL) is recognized for it’s expertise in the development of new measurement techniques and their application to challenges of national importance. So it was obvious to us to address the need for in-situ analysis of large scale experimental data. We have a wide range of experimental instruments on site, in facilities such as DOE’s national scientific user facility, the William R. Wiley Environmental Molecular Sciences Laboratory (EMSL). Commonly, scientists would create an individual analysis pipeline for each of those instruments; but even the same type of instrument would not necessarily share the same analysis tools. With the rapid increase of data volumes and rates we were facing two key challenges: how to bring a wider set of capabilities to bear to achieve in-situ analysis, and how to do so across a wide range of heterogeneous instruments at affordable costs and in a reasonable timeframe. We decided to take an unconventional approach to the problem, rather than developing customized, one-off solutions for specific instruments we wanted to explore if a more common solution could be found that would go beyond shared, basic infrastructures such as data movement and workflow engines.

97 MATHEMATICS AND COMPUTING↗

High-Throughput Combinatorial Development of High-Entropy Alloys For Light-Weight Structural Applications

The primary limitation of today’s lightweight structural alloys is that specific yield strengths (SYS) higher than 200MPa x cc/g (typical value for titanium alloys) are extremely difficult to achieve. This holds true especially at a cost lower than 5dollars/kg (typical value for magnesium alloys). Recently, high-entropy alloys (HEA) have shown promising SYS, yet the large composition space of HEA makes screening compositions complex and time-consuming. Over the course of this 2-year project we started from 150 billion compositions and reduced the number of potential low-density (<5g/cc), low-cost (<5dollars/kg) high-entropy alloy (LDHEA) candidates that are single-phase, disordered, solid-solution (SPSS) to a few thousand compositions. This was accomplished by means of machine learning to guide design for SPSS LDHEA based on a combination of recursive partitioning, an extensive, experimental HEA database compiled from 24 literature sources, and 91 calculated parameters serving as phenomenological selection rules. Machine learning shows an accuracy of 82% in identifying which compositions of a separate, smaller, experimental HEA database are SPSS HEA. Calculation of Phase Diagrams (CALPHAD) shows an accuracy of 71-77% for the alloys supported by the CALPHAD database, where 30% of the compiled HEA database is not supported by CALPHAD. In addition to machine learning, and CALPHAD, a third tool was developed to aid design of SPSS LDHEA. Phase diagrams were calculated by constructing the Gibbs-free energy convex hull based on easily accessible enthalpy and entropy terms. Surprisingly, accuracy was 78%. Pursuing these LDHEA candidates by high-throughput experimental methods resulted in SPSS LDHEA composed of transition metals (e.g. Cr, Mn, Fe, Ni, Cu) alloyed with Al, yet the high concentration of Al, necessary to bring the mass density below 5.0g/cc, makes these materials hard and brittle, body-centered-cubic (BCC) alloys. A related, yet multi-phase BCC alloy, based on Al-Cr-Fe-Ni, shows compressive strain >10% and specific compressive yield strength of 229 MPa x cc/g, yet does not show ductility in tensile tests due to cleavage. When replacing Cr in Al-Cr-Fe-based 4- and 5-element LDHEA with Mn, hardness drops 2x. Combined with compression test results, including those on the ternaries Al-Cr-Fe and Al-Mn-Fe suggest that Al-Mn-Fe-based LDHEA are still worth pursuing. These initial results only represent one compressive stress-strain curve per composition without any property optimization. As such, reproducibility needs to be followed by optimization to show their full potential. When including Li, Mg, and Zn, single-phase Li-Mg-Al-Ti-Zn LDHEA has been found with a specific ultimate compressive strength of 289MPa x cc/g. Al-Ti-Mn-Zn showed a specific ultimate compressive strength of 73MPa x cc/g. These initial results after hot isostatic pressing (HIP) of the ball-milled powders represent the lower end of what is possible, since no secondary processing (e.g. extrusion) has been performed to optimize strength and ductility. Compositions for multi-phase (e.g. dual-phase) LDHEA were identified largely by automated searches through CALPHAD databases, while screening for large face-centered-cubic (FCC) volume fractions, followed by experimental verification. This resulted in several new alloys. Li-Mg-Al-Mn-Fe and Mg-Mn-Fe-Co ball-milled powders upon HIP show specific ultimate compressive strengths of 198MPa x cc/g and 45MPa x cc/g, respectively. Several malleable quarternary Al-Zn-based alloys have been found upon arc/induction melting, yet with limited specific compressive yield strength (<75 MPa x cc/g). These initial results are all without any optimization for strength and/or ductility. High-throughput experimentation allowed us to triple the existing experimental HEA database as published in the past 10 years in less than 2 years which happened at a rate 10x higher than previous methods. Furthermore, we showed that high-throughput thin-film combinatorial methods can be used to get insight in isothermal phase diagram slices. Although it is straightforward to map hardness as a function of composition for sputtered, thin-film, compositional gradients by nano-indentation and compare the results to micro-indentation on bulk samples, the simultaneous impact of composition, roughness, film density, and microstructure on hardness requires monitoring all these properties as a function of location on the compositional gradient, including dissecting the impact of these 4 factors on the hardness map. These additional efforts impact throughput significantly. This work shows that a lot of progress has been made over the years in predicting phase formation that aids the discovery of new alloys, yet that a lot of work needs to be done to predict phases more accurately for LDHEA, whether done by CALPHAD or by other means. More importantly, more work needs to be done to predict mechanical properties of novel alloys, like yield strength, and ductility. Furthermore, this work shows that there is a need for the generation of an empirical alloy database covering strategic points in a multi-dimensional composition space to allow for faster and more accurate predictive interpolations to identify the oasis in the dessert more quickly. Finally, this work suggests that it is worth pursuing a ductile alloy with a SYS > 300 MPa x cc/g in a mass density range of 6-7 g/cc, since the chances for a single-phase or majority-phase FCC increase significantly. Today’s lightweight steels are in this density range.

36 MATERIALS SCIENCE↗

Accelerated Testing of Selected Filler Compositions

The fillers R&D program, mostly experimental, is part of a broader R&D program that includes new process modeling and performance assessment of criticality effects and the overall importance of criticality to repository performance (consequence screening). A literature research and consultation effort with experts by Hardin and Brady (2018) identified several potentially effective and workable filler materials including cements (primarily phosphate based), molten-metal alloys, and low-temperature glasses. Filler attributes were defined and the preliminary lists were compared qualitatively. Further comparative analysis will be done (e.g., cost estimates) after experimental screening has narrowed the list of alternatives. The following cement filler compositions were selected for experimental development work and accelerated testing in FY19: Aluminum phosphate cements (APCs); more specifically aluminum oxide / aluminum phosphate (Al 2 O 3 / AlPO 4 ) cements in which Al 2 O 3 serves as the filler material bound by an AlPO 4 binder formed by the reaction of Al 2 O 3 with H 3 PO 4 ; Calcium phosphate cements (CPCs); more specifically composed of pure or nearly pure hydroxyapatite (Ca 5 (PO 4 ) 3 (OH)); Magnesium potassium phosphate cements (MKPs) composed of magnesium oxide / magnesium potassium phosphate (MgO / MgKPO 4 ) cements in which MgO serves as the filler and MgKPO 4 serves as the binder formed by the reaction of MgO with monopotassium phosphate (KH 2 PO 4 ) and tricalcium phosphate ((Ca 3 (PO 4 ) 2 ); Two additional potential cement materials were explored preliminarily as the result of: (1) continued literature investigations into other filler candidates (wollastonite-based phosphate ceramic) and (2) the experimental discovery of a well-consolidated fly ash phosphate cement during the evaluation of fly ash as a potential filler material with Al 2 O 3 in APCs. Fly ash phosphate cements, more specifically in which a fly ash material composed primarily of mullite and quartz serves as the filler and is reacted with H 3 PO 4 to form amorphous phosphate phase(s) as the binder; Wollastonite aluminum phosphate cements (WAPC), specifically wollastonite / aluminum phosphate (CaSiO 3 / AlPO 4 ) in which CaSiO 3 serves as the filler material and AlPO 4 serves as the binder formed by Al(OH) 3 or metakaolin as Al sources and H 3 PO 4 or ammonium dihydrogen phosphate (ADP) (NH 4 H 2 PO 4 ) as phosphate sources. The FY19 effort focused on the optimization of compositions and subsequent processing of these five materials to achieve dense and well-consolidated monolithic samples with relatively low porosity. Once these goals were met basic material properties screening evaluations were performed including an assessment of dissolution resistance in water at elevated temperature (200 °C) and mechanical testing including unconfined compressive strength (UCS) testing. To date, the aluminum phosphate cements (APCs) appear to show the most promise for continued development. They are easily prepared and form smooth pourable slurries that remain stable for days with relatively low viscosities of several thousand centipoise (cP). They are then set at elevated temperatures (e.g., 170 °C) under ambient (0.1 MPa) or elevated pressure (~1MPa). Overall, they demonstrate the best dissolution resistance in water at elevated temperature (200 °C) and good compressive strengths. However, additional effort is required to optimize the APC slurry formulations and the process used for thermal curing these materials. The calcium phosphate cements (CPCs) can be formed at room temperature to produce a well-consolidated body. However, their slurry viscosities are very high (and difficult to measure) and they exhibit relatively short cure times of 2 to 3 hours. Also, dissolution resistance is very poor, the poorest of all the cements examined The same is the case for the small number of MKP cements fabricated; they cure very quickly (10 minutes or less) and disintegrate within a few hours upon immersion in distilled water. Surprisingly, fly ash reacts with phosphoric acid to form dense and well-consolidated cements but the mixture rapidly sets at room temperature (less than 30 minutes) and the subsequent conversion of the binder to an amorphous phosphate phase(s) as a function of temperature is complicated. Finally, the wollastonite aluminum phosphate cements (WAPC) are easily prepared and form smooth pourable slurries that remain stable for several hours. They are then set at 130 °C. A WAPC sample exhibited the highest compressive strengths of all the materials we evaluated but in general their dissolution resistance to water is poor.

36 MATERIALS SCIENCE↗

Optimized aperiodic multilayer structures for use as narrow-angular absorbers

In this paper, we investigate aperiodic multilayer structures for use as narrow-angular absorbers. The layer thicknesses and materials are optimized using a genetic global optimization algorithm coupled to a transfer matrix code to maximize the angular selectivity in the absorptance at a single or multiple wavelengths. We first consider structures composed of alternating layers of tungsten and silicon or silica, and find that it is not possible to achieve angular selectivity in the absorptance with such structures. We next consider structures composed of alternating layers of silicon and silica, and show that when optimized they exhibit high angular selectivity in absorptance. In addition, as the angular selectivity in absorptance increases, the wavelength range of high angular selectivity also decreases. Optimizing the material composition of the multilayer structures, in addition to optimizing the layer thicknesses, leads to marginal improvement in angular selectivity. Finally, we show that by optimizing the absorptance of the multilayer structures at multiple wavelengths, we can obtain structures exhibiting almost perfect absorptance at normal incidence and narrow angular width in absorptance at these wavelengths. Similar to the structures optimized at a single wavelength, the wavelength range of high angularly selective absorptance is narrow.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Protein intake is more stable than carbohydrate or fat intake across various US demographic groups and international populations

The optimal macronutrient composition of the diet is controversial and many adults attempt to regulate the intake of specific macronutrients for various health-related reasons. The objective was to compare stability and ranges of intakes of different macronutrients across diverse adult populations in the USA and globally. US dietary intake data from NHANES 2009–2014 were used to determine macronutrient intake as a percentage of total energy intake. Variability in macronutrient intake was estimated by calculating the difference between 75th and 25th percentile (Q3–Q1) IQRs of macronutrient intake distributions. In addition, intake data from 13 other countries with per capita gross domestic product (GDP) over $10,000 US dollars (USD) were used to assess variability of intake internationally since there are large differences in types of foods consumed in different countries. Protein, carbohydrate, and fat intake (NHANES 2009–2014) was 15.7 ± 0.1, 48.1 ± 0.1, and 32.9 ± 0.1% kcal, respectively, in US adults. The IQR of protein intake distribution (3.73 ± 0.11% kcal) was 41% of carbohydrate intake distribution (9.18 ± 0.20% kcal) and 58% of fat intake distribution (6.40 ± 0.14% kcal). The IQRs of carbohydrate and fat intake distributions were significantly (P <0.01) influenced by age and race; however, the IQR of protein intake was not associated with demographic and lifestyle factors including sex, race, income, physical activity, and body weight. International mean protein intake was 16.3 ± 0.2% kcal, similar to US intake, and there was less variation in protein than carbohydrate or fat intake. Protein intake of the US population and multiple international populations, regardless of demographic and lifestyle factors, was consistently ~16% of total energy, suggesting biological control mechanism(s) tightly regulate protein intake and, consequently, influence intake of other macronutrients and food constituents. Substantial differences in intake of the other macronutrients observed in US and international populations had little influence on protein intake. This trial was registered at the ISRCTN registry as ISRCTN46157745

dietary preferences↗

3D Printing of Highly Porous Polypropylene Separators for Lithium‐Ion Batteries Using Fused Deposition Modeling and Thermally Induced Phase Separation

Appearing as one of the key-components of lithium-ion batteries (LIBs), this work specifically focuses on the additive manufacturing (AM) of custom-shape separators, facilitated by the filament material extrusion process, also called fused deposition modeling (FDM). The development and optimization of composite thermoplastic filament feedstocks combining polypropylene and paraffin wax, followed by the 3D printing of the separator membranes is shown. A post-processing step, based on thermal induced phase separation (TIPS), is introduced to promote porosity formation through removal of the paraffin wax sacrificial phase within the 3D printed items. Separators with different polypropylene/paraffin wax ratios are developed and the impact on printability, mechanical strength, porosity, and electrochemical performances, is thoroughly discussed. X-ray micro-computed tomography is employed to assess the geometric fidelity and to detect printing defects in a complex 3D lattice structure. The performance of the 3D printed porous separators is also compared to a commercial separator. This pioneering research establishes a foundation for the creation of porous separators that can adapt to and conform into 3D printed battery architectures with novel form factors, and also creates opportunities for the use of FDM and TIPS for a wide range of applications that employ porous structures beyond the energy storage field.

3D printing↗

Deep Learning for Rapid Analysis of Spectroscopic Ellipsometry Data

High‐throughput experimental approaches to rapidly develop new materials require high‐throughput data analysis methods to match. Spectroscopic ellipsometry is a powerful method of optical properties characterization, but for unknown materials and/or layer structures the data analysis using traditional methods of nonlinear regression is too slow for autonomous, closed‐loop, high‐throughput experimentation. Herein, three methods (termed spectral, piecewise, and pointwise) of spectroscopic ellipsometry data analysis based on deep learning are introduced and studied. After initial training, the incremental time for inferring optical properties can be a thousand times faster than traditional methods. Results for multilayer sample structures with optically isotropic materials are presented, appropriate for high‐throughput studies of thin films of phase‐change materials such as GeSbTe (GST) alloys. Results for studies on highly birefringent layered materials are also presented, exemplified by the transition metal dichalcogenide MoS 2 . How the materials under test and the experimental objectives may guide the choice of analysis methods are discussed. The utility of our approach is demonstrated by analyzing data measured on a composition spread of GeSbTe phase‐change alloys containing 177 distinct compositions, and identifying the composition with optimal phase‐change figure of merit in only 1.4 s of analysis time.

Li, Yifei↗

Simultaneously tuning dense skin and porous substrate of asymmetric hollow fiber membranes for efficient purification of aggressive natural gas

Highly permeable, selective, and stable asymmetric membranes are required to replace the traditional separation approaches for natural gas purification with higher energy efficiency and smaller footprints. In this work, we report on the design and engineering of defect-free asymmetric hollow fiber membranes with a thin dense skin and highly porous substrate to effectively deal with aggressive natural gas. A crosslinkable polymer with rigid molecular structure and high molecular weight was synthesized for developing spinning dope with desirable solution properties. Phase separation behavior of the polymer was carefully controlled by systematic formulation of the dope composition and optimizing spinning conditions, thereby realizing simultaneously tuning dense skins and porous substrates of the spun asymmetric hollow fiber membranes. The crosslinked hollow fiber membrane, with well-preserved delicate asymmetric nanostructures, exhibited unprecedentedly high and stable separation performance for long-term processing extremely aggressive CO 2 /CH 4 mixtures (with pressure up to 820 psi containing C6(+) hydrocarbons), thereby showing great potential for practical application of natural gas purification. This research provides a new platform to create hollow fiber membranes with both high permeance and plasticization resistance in natural gas service.

36 MATERIALS SCIENCE↗

Neutron Gamma-Method for Monitoring Ash Content of Coal

A brief analysis is given of the modern instrumental methods of monitoring the ash content of coal. Their particulars and drawbacks are examined. A neutron gamma-method of monitoring the ash content is proposed on the basis of integrated use of prompt γ-radiation accompanying inelastic scattering of fast neutrons and radiative capture of thermal neutrons by nuclei of the primary elements comprising the organic and mineral components of coal. The instrumental-methodological parameters of monitoring (sizes of the analyzed samples, energy intervals of the detected gamma radiation) making it possible to the increase the sensitivity of the method with respect to the ash content and to minimize the impact of the variability of the moisture content of coal on its material composition, are optimized. The method has been certified and recommended for representative monitoring of the quality of coarse coal.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Phase stability and transformation in a light-weight high-entropy alloy

Light-weight high-entropy alloys (HEAs) with a vast alloy-design space have offered new avenues to explore novel low-cost, high strength-to-weight ratio structural materials. Studying their phase stability and possible transformations is critical for designing microstructures for optimal material properties. However, the complex local atomic environment of HEAs poses challenges to the fundamental understanding of phase stability and transformation behaviors. The present paper investigates the phase stability and transformation behaviors of a newly-designed light-weight Al 1.5 CrFeMnTi HEA by integrated experimental and theoretical approaches. The coherent precipitation of the L2 1 phase within the body-centered-cubic (BCC) matrix at intermediate temperatures was observed, and the size, shape, coherency, and spatial distribution of the L2 1 phase were subsequently altered through selected annealing treatments. Moreover, the CALculation of PHAse Diagrams (CALPHAD) and first-principle calculations successfully optimize the compositions of light-weight HEAs with a coherent BCC/L2 1 two-phase structure. Finally, shed light by the present study, novel light-weight HEAs, featuring the lower density (below 6 g/cm 3 ) and cost, can be designed for high-temperature applications.

36 MATERIALS SCIENCE↗

Coupled effect of Cr and Al on interactions between a prismatic interstitial dislocation loop and an edge dislocation line in Fe-Cr-Al alloy

Segregation of alloying elements to a prismatic dislocation loop under irradiation is an important phenomenon in understanding the role of loops in radiation effects in alloys. In this work, various segregation sequences of Cr and Al atoms to a $\langle$100$\rangle$ and a 1/2 $\langle$111$\rangle$ prismatic dislocation loop in a Fe-Cr-Al alloy are explored using molecular dynamics method and ab initio energy calculation. Here, the results reveal that Cr can readily segregate to the loops while Al atoms cannot by themselves, but the segregated Cr atoms are able to promote Al segregation at the loops, defined as a coupled segregation of Cr and Al. After interacting with Cr and Al, a previously mobile 1/2 $\langle$111$\rangle$ loop becomes sessile. Al segregation through the coupled segregation process can further affect the pinning behavior of a dislocation loop to an edge dislocation motion. By varying the Al fraction in the segregated solutes, a nonlinear dependence of the pinning effect on dislocation motion is determined. At lower fractions, the pinning strength increases with the increasing Al fraction until Al fraction reaches a critical value of about 19%, above which the pinning strength decreases with further increase of Al fraction. All these results suggest that, in addition to the effect of Al on the surface resistance to oxidation, Al effect on the dislocation loop behavior is important to optimize the composition of Fe-Cr-Al alloys for their applications in accident tolerant fuel concepts.

36 MATERIALS SCIENCE↗

Redox oxide@molten salt as a generalized catalyst design strategy for oxidative dehydrogenation of ethane via selective hydrogen combustion

Here, the current study demonstrates a redox oxide @ molten salt core-shell architecture as a generalized redox catalyst design strategy for chemical looping – oxidative dehydrogenation of ethane. 17 combinations of redox active oxides and molten salts were prepared, evaluated, and characterized. X-ray diffraction indicates that the redox oxides and molten salts are fully compatible, forming separate and stable phases. X-ray photoelectron spectroscopy demonstrates that the molten salts aggregate at the redox oxide surface, forming a core-shell structure to block the non-selective sites responsible for CO x formation. Up to ~74% single-pass olefin yields were achieved using the proposed redox catalyst design strategy. Statistical analyses of the performance data indicate the potential to achieve up to 86.7% single-pass yield by simply optimizing the operating conditions using the redox catalysts reported in this study. Meanwhile, the generalizability of the catalyst design strategy offers exciting opportunities to further optimize the composition and performance of the redox catalysts for ethane ODH under a chemical looping scheme with significantly reduced energy consumption and CO 2 emissions.

03 NATURAL GAS↗

Understanding the Origin of Negative Temperature Dependence and Activity of N-Coordinated Cobalt Sites During Ethylene Dimerization

The on-demand production of short-chain linear alpha olefins (LAOs; C4-C8) via C2H4 dimerization and oligomerization is industrially attractive, prompting extensive research on designing active, selective, and stable catalysts for industrial use. Cobalt supported on ammoniated carbon (Co(NH3)x/C) catalysts have shown remarkable activity and selectivity in this process. However, critical aspects such as the active phase, active site structure, the role of the catalyst support, cobalt loading effects, and the inverse correlation of the reaction rate with temperature remain inadequately understood. This study systematically explores these factors using a combination of steady-state differential catalytic tests, in situ molecular characterization including diffuse reflectance UV-Vis (DR-UV-Vis), Infrared, and Raman spectroscopies, and ex situ X-ray diffraction (XRD) and high annular aberration-corrected dark field transmission electron microscopy (HAADF-STEM). Various supports (SiO2, Al2O3, NH4-ZSM-5, g-C3N4, and C) and cobalt loadings (1.0-3.0 Co nm-2) were studied to determine the optimal catalyst composition and identify the active phase and sites. Carbon-supported catalysts uniquely produce C4-8 LAOs during C2H4 dimerization, with site-time-yield remaining constant (~10-3 s-1) for 1.0-4.0 Co nm-2 at prolonged reaction times (24-48?h time-on-stream). At higher loadings of 6.0 Co nm-2, the formation of crystalline CoO and Co3O4 phases reduces catalytic activity and LAO selectivity. Our findings show that active catalysts lack crystalline cobalt oxides and instead feature dispersed Co2+ sites, tetra-coordinated to a mix of N/NH3 and O/H2O ligands, which catalyze C2H4 dimerization via the Cossee-Arlman mechanism, exhibiting 1st order dependence on C2H4 concentration. The observed inverse rate-temperature correlation is attributed to compensation effects (i.e., presence of Cremer-Constable relationship) linked to changes in adsorption enthalpic and entropic factors.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Multiscale metrologies for process optimization of carbon nanotube polymer composites

Carbon nanotube (CNT) polymer nanocomposites are attractive multifunctional materials with a growing range of commercial applications. With the increasing demand for these materials, it is imperative to develop and validate methods for on-line quality control and process monitoring during production. In this work, a novel combination of characterization techniques is utilized, that facilitates the non-invasive assessment of CNT dispersion in epoxy produced by the scalable process of calendering. First, the structural parameters of these nanocomposites are evaluated across multiple length scales (10 -10 m to 10 -3 m) using scanning gallium-ion microscopy, transmission electron microscopy and small-angle neutron scattering. Then, a non-contact resonant microwave cavity perturbation (RCP) technique is employed to accurately measure the AC electrical conductivity of the nanocomposites. Quantitative correlations between the conductivity and structural parameters find the RCP measurements to be sensitive to CNT mass fraction, spatial organization and, therefore, the processing parameters. These results, and the non-contact nature and speed of RCP measurements identify this technique as being ideally suited for quality control of CNT nanocomposites in a nanomanufacturing environment. In conclusion, when validated by the multiscale characterization suite, RCP may be broadly applicable in the production of hybrid functional materials, such as graphene, gold nanorod, and carbon black nanocomposites.

36 MATERIALS SCIENCE↗