SEARCH · Search NASA

Results for “computation fluid dynamics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

All sources NASA NTRS DOE OSTI

NASA NTRS1995

Evaluation of Aircraft Platforms for SOFIA by Computational Fluid Dynamics

The selection of an airborne platform for the Stratospheric Observatory for Infrared Astronomy (SOFIA) is based not only on economic cost, but technical criteria, as well. Technical issues include aircraft fatigue, resonant characteristics of the cavity-port shear layer, aircraft stability, the drag penalty of the open telescope bay, and telescope performance. Recently, two versions of the Boeing 747 aircraft, viz., the -SP and -200 configurations, were evaluated by computational fluid dynamics (CFD) for their suitability as SOFIA platforms. In each configuration the telescope was mounted behind the wings in an open bay with nearly circular aperture. The geometry of the cavity, cavity aperture, and telescope was identical in both platforms. The aperture was located on the port side of the aircraft and the elevation angle of the telescope, measured with respect to the vertical axis, was 500. The unsteady, viscous, three-dimensional, aerodynamic and acoustic flow fields in the vicinity of SOFIA were simulated by an implicit, finite-difference Navier-Stokes flow solver (OVERFLOW) on a Chimera, overset grid system. The computational domain was discretized by structured grids. Computations were performed at wind-tunnel and flight Reynolds numbers corresponding to one free-stream flow condition (M = 0.85, angle of attack alpha = 2.50, and sideslip angle beta = 0 degrees). The computational domains consisted of twenty-nine(29) overset grids in the wind-tunnel simulations and forty-five(45) grids in the simulations run at cruise flight conditions. The maximum number of grid points in the simulations was approximately 4 x 10(exp 6). Issues considered in the evaluation study included analysis of the unsteady flow field in the cavity, the influence of the cavity on the flow across empennage surfaces, the drag penalty caused by the open telescope bay, and the noise radiating from cavity surfaces and the cavity-port shear layer. Wind-tunnel data were also available to compare to the CFD results; the data permitted an assessment of CFD as a design tool for the SOFIA program.

Klotz, S. P.↗

NASA NTRS1993

Experience in using SIMD and MIMD parallelism for computational fluid dynamics

One of the key objectives of the Applied Research Branch in the Numerical Aerodynamic Simulation (NAS) Systems Division at NASA Ames Research Center is the accelerated introduction of highly parallel machines into a fully operational environment. In this report we summarize some of the experiences with the parallel testbed machines at the NAS Applied Research Branch. We discuss the performance results obtained from the implementation of two computational fluid dynamics (CFD) applications, an unstructured grid solver and a particle simulation, on the Connection Machine CM-2 and the Intel iPSC/860.

Simon, Horst D.↗

NASA NTRS2013

A Computational Fluid Dynamics Study of Swirling Flow Reduction by using Anti-vortex Baffle

An anti-vortex baffle is a liquid propellant management device placed adjacent to an outlet of the propellant tank. Its purpose is to substantially reduce or eliminate the formation of free surface dip and vortex, as well as prevent vapor ingestion into the outlet, as the liquid drains out through the flight. To design an effective anti-vortex baffle, Computational Fluid Dynamic (CFD) simulations were undertaken for the NASA Ares I vehicle LOX tank subjected to the simulated flight loads with and without the anti-vortex baffle. The Six Degree-Of-Freedom (6- DOF) dynamics experienced by the Crew Launch Vehicle (CLV) during ascent were modeled by modifying the momentum equations in a CFD code to accommodate the extra body forces from the maneuvering in a non-inertial frame. The present analysis found that due to large moments, the CLV maneuvering has significant impact on the vortical flow generation inside the tank. Roll maneuvering and side loading due to pitch and yaw are shown to induce swirling flow. The vortical flow due to roll is symmetrical with respect to the tank centerline, while those induced by pitch and yaw maneuverings showed two vortices side by side. The study found that without the anti-vortex baffle, the swirling flow caused surface dip during the late stage of drainage and hence early vapor ingestion. The flow can also be non-uniform in the drainage pipe as the secondary swirling flow velocity component can be as high as 10% of the draining velocity. An analysis of the vortex dynamics shows that the swirling flow in the drainage pipe during the Upper Stage burn is mainly the result of residual vortices inside the tank due to conservation of angular momentum. The study demonstrated that the swirling flow in the drainage pipe can be effectively suppressed by employing the anti-vortex baffle.

Yang, H. Q.↗

NASA NTRS2017

A Computational Fluid Dynamics Study of Swirling Flow Reduction by Using Anti-Vortex Baffle

An anti-vortex baffle is a liquid propellant management device placed adjacent to an outlet of the propellant tank. Its purpose is to substantially reduce or eliminate the formation of free surface dip and vortex, as well as prevent vapor ingestion into the outlet, as the liquid drains out through the flight. To design an effective anti-vortex baffle, Computational Fluid Dynamic (CFD) simulations were undertaken for the NASA Ares I vehicle LOX tank subjected to the simulated flight loads with and without the anti-vortex baffle. The Six Degree-Of-Freedom (6-DOF) dynamics experienced by the Crew Launch Vehicle (CLV) during ascent were modeled by modifying the momentum equations in a CFD code to accommodate the extra body forces from the maneuvering in a non-inertial frame. The present analysis found that due to large moments, the CLV maneuvering has a significant impact on the vortical flow generation inside the tank. Roll maneuvering and side loading due to pitch and yaw are shown to induce swirling flow. The vortical flow due to roll is symmetrical with respect to the tank centerline, while those induced by pitch and yaw maneuverings showed two vortices side by side. The study found that without the anti-vortex baffle, the swirling flow caused surface dip during the late stage of drainage and hence early vapor ingestion. The flow can also be non-uniform in the drainage pipe as the secondary swirling flow velocity component can be as high as 10% of the draining velocity. An analysis of the vortex dynamics shows that the swirling flow in the drainage pipe during the Upper Stage burn is mainly the result of residual vortices inside the tank due to the conservation of angular momentum. The study demonstrated that the swirling flow in the drainage pipe can be effectively suppressed by employing the anti-vortex baffle.

Yang, H. Q.↗

NASA NTRS2017

A Computational Fluid Dynamics Study of Swirling Flow Reduction by Using Anti-Vortex Baffle

An anti-vortex baffle is a liquid propellant management device placed adjacent to an outlet of the propellant tank. Its purpose is to substantially reduce or eliminate the formation of free surface dip and vortex, as well as prevent vapor ingestion into the outlet, as the liquid drains out through the flight. To design an effective anti-vortex baffle, Computational Fluid Dynamic (CFD) simulations were undertaken for the NASA Ares I vehicle LOX tank subjected to the simulated flight loads with and without the anti-vortex baffle. The Six Degree-Of-Freedom (6-DOF) dynamics experienced by the Crew Launch Vehicle (CLV) during ascent were modeled by modifying the momentum equations in a CFD code to accommodate the extra body forces from the maneuvering in a non-inertial frame. The present analysis found that due to large moments, the CLV maneuvering has a significant impact on the vortical flow generation inside the tank. Roll maneuvering and side loading due to pitch and yaw are shown to induce swirling flow. The vortical flow due to roll is symmetrical with respect to the tank centerline, while those induced by pitch and yaw maneuverings showed two vortices side by side. The study found that without the anti-vortex baffle, the swirling flow caused surface dip during the late stage of drainage and hence early vapor ingestion. The flow can also be non-uniform in the drainage pipe as the secondary swirling flow velocity component can be as high as 10% of the draining velocity. An analysis of the vortex dynamics shows that the swirling flow in the drainage pipe during the Upper Stage burn is mainly the result of residual vortices inside the tank due to the conservation of angular momentum. The study demonstrated that the swirling flow in the drainage pipe can be effectively suppressed by employing the anti-vortex baffle.

Yang, H. Q.↗

NASA NTRS1987

Computational fluid dynamics: Transition to design applications

The development of aerospace vehicles, over the years, was an evolutionary process in which engineering progress in the aerospace community was based, generally, on prior experience and data bases obtained through wind tunnel and flight testing. Advances in the fundamental understanding of flow physics, wind tunnel and flight test capability, and mathematical insights into the governing flow equations were translated into improved air vehicle design. The modern day field of Computational Fluid Dynamics (CFD) is a continuation of the growth in analytical capability and the digital mathematics needed to solve the more rigorous form of the flow equations. Some of the technical and managerial challenges that result from rapidly developing CFD capabilites, some of the steps being taken by the Fort Worth Division of General Dynamics to meet these challenges, and some of the specific areas of application for high performance air vehicles are presented.

Bradley, R. G.↗

NASA NTRSDate not supplied

Integrated Computational Fluid Dynamics and Thermal Desktop Thermal Modeling for Assessment of the EMU in Support of ISS EVA 80

Following the reports of water accumulation in the Extravehicular Mobility Unit (EMU) helmet during the ISS US EVA-80, various efforts for mitigation and further understanding of this phenomenon have been undertaken with the goal of prevention and to ensure crew safety in future EVAs. In support of this goal, a combination of Thermal Desktop thermal modeling and Computational Fluid Dynamics (CFD) has been performed in order to characterize the performance of the EMU components, specifically those within the ventilation/cooling water loops. This modeling effort evaluates the dry/wet gas pressure drop and flow distribution through gas and liquid flow paths using CFD, as well as a two-phase flow assessment of condensation production and water separation/removal performance using an integrated Thermal Desktop model of important EMU ventilation loop components. The models assess this overall thermal-fluid performance in comparison with previous existing models, design points, and historical EVA data using their inputs.

Blain Ryan Lancaster↗

NASA NTRSDate not supplied

Integrated Computational Fluid Dynamics and Thermal Desktop Thermal Modeling for Assessment of the EMU in Support of ISS EVA 80

EVA 80↗

NASA NTRSDate not supplied

Computational Fluid Dynamics Simulation of the Swordfish Oxygen/Methane Rotating Detonation Rocket Engine

Rotating Detonation Rocket Engines (RDREs) provide several theoretical performance benefits over traditional deflagration combustion rocket engines. RDREs can potentially generate higher specific impulse (ISP) for a given propellant combination enabling significant consumable mass savings for a spaceflight vehicle. Conversely, RDREs are a relatively new technology with a shallower analytical modeling base compared to traditional combustion engine architectures. In this work, we utilize time-accurate, Computational Fluid Dynamics (CFD) modeling to simulate the complex fluid environment inside an RDRE combustion chamber and propellant manifolds. The selected engine of study is the Swordfish RDRE which was developed and tested and at the National Aeronautics and Space Administration (NASA) Marshall Space Flight Center (MSFC). CFD simulations were conducted using the as-tested Swordfish geometry and conditions to facilitate comparison between the analytical predictions and experimental results.

Brian R. Richardson↗

DOE OSTI2025

Comparison of a Full-Scale and a 1:10 Scale Low-Speed Two-Stroke Marine Engine Using Computational Fluid Dynamics

International marine shipping is a growing component of international trade; a vast majority of all the world’s goods are being transported on large ocean-going vessels. The International Maritime Organization (IMO) introduced the Energy Efficiency Design Index in 2013, a regulatory framework of associated metrics for reducing emissions of CO 2 per tonne-mile from shipping by approximately 10% each decade. Therefore, decarbonizing the maritime sector requires the development of new fuel sources. Because of the extremely large physical size of the internal combustion engines present in shipping vessels, experimental iterative development of the engine and fuel system is cost-prohibitive. Thus, the ability to perform combustion system development in a scaled platform that can be more easily operated and modeled computationally is of interest. To that end, scaling relationships are needed to translate the results from a smaller engine to a larger counterpart. Scaling studies to date have been restricted to low scaling ratios, four-stroke light-duty engines, and under-resolved computational fluid dynamic simulations that likely do not accurately capture the physics of scaling. In this work, computational models of a 1:10 scale and a full-scale two-stroke crosshead low-speed marine engine were created and validated against experiments obtained in a real 1:10 scale engine installed at Oak Ridge National Laboratory. Further, due to the large size of the full-scale engine, the model required large high-performance computing resources to be evaluated. The availability of high-performance computing resources at the Department of Energy’s Leadership Computing Facilities is an enabler of the current work. The results of the small- and large-scale engine simulations were compared to analyze the effectiveness of the appropriate scaling laws under these extreme scaling ratio conditions.

33 ADVANCED PROPULSION SYSTEMS↗

DOE OSTI2021

Computational Fluid Dynamic Simulation for Electrolyte Flow in Horizontal EP of Nb SRF Elliptical Cavities

An electrolyte flow velocity on an electropolishingsurface affects a material removal rate where higherremoval is observed with a higher velocity of theelectrolyte. In horizontal EP (HEP) of an ellipticalcavity, an electrolyte flow near the equator positionmight remain slow and responsible for a lowerremoval compared to that on the iris and beam pipepositions. In order to understand the flow dynamicon an elliptical cavity surface in the horizontal EPprocess, a computational fluid dynamic simulationwas conducted. This study was conducted on 1.3GHz cavity with different cathodes and acid flowrates. Final aim of the study is to improve the flowuniformity to attain uniform removal especially inmulticell cavities.

Chouhan, V.↗

DOE OSTI2020

A space-time parallel algorithm with adaptive mesh refinement for computational fluid dynamics

This work describes a space-time parallel algorithm with space-time adaptive mesh refinement (AMR). AMR with subcycling is added to multigrid reduction-in-time (MGRIT) in order to provide solution efficient adaptive grids with a reduction in work performed on coarser grids. This algorithm is achieved by integrating two software libraries: XBraid (Parallel time integration with multigrid. https://computation.llnl.gov/projects/parallel-timeintegration-multigrid) and Chombo (Chombo software package for AMR applications—design document, 2014). The former is a parallel time integration library using multigrid and the latter is a massively parallel structured AMR library. Employing this adaptive space-time parallel algorithm is Chord (Comput Fluids 123:202–217, 2015), a computational fluid dynamics (CFD) application code for solving compressible fluid dynamics problems. For the same solution accuracy, speedups are demonstrated from the use of space-time parallelization over the time-sequential integration on Couette flow and Stokes’ second problem. On a transient Couette flow case, at least a 1.5× speedup is achieved, and with a time periodic problem, a speedup of up to 13.7× over the time-sequential case is obtained. In both cases, the speedup is achieved by adding processors and exploring additional parallelization in time. The numerical experiments show the algorithm is promising for CFD applications that can take advantage of the time parallelism. Future work will focus on improving the parallel performance and providing more tests with complex fluid dynamics to demonstrate the full potential of the algorithm.

97 MATHEMATICS AND COMPUTING↗

NASA NTRS1992

Computational fluid dynamics analysis of SSME phase 2 and phase 2+ preburner injector element hydrogen flow paths

Phase 2+ Space Shuttle Main Engine powerheads, E0209 and E0215 degraded their main combustion chamber (MCC) liners at a faster rate than is normal for phase 2 powerheads. One possible cause of the accelerated degradation was a reduction of coolant flow through the MCC. Hardware changes were made to the preburner fuel leg which may have reduced the resistance and, therefore, pulled some of the hydrogen from the MCC coolant leg. A computational fluid dynamics (CFD) analysis was performed to determine hydrogen flow path resistances of the phase 2+ fuel preburner injector elements relative to the phase 2 element. FDNS was implemented on axisymmetric grids with the hydrogen assumed to be incompressible. The analysis was performed in two steps: the first isolated the effect of the different inlet areas and the second modeled the entire injector element hydrogen flow path.

Ruf, Joseph H.↗

DOE OSTI2022

A Computational Fluid Dynamic Study on Polymer Heat Exchangers

Polymer heat exchangers have been developed for the applications involving weight restrictions or chemical compatibility and fouling issues owing to the low density, anticorrosive properties, and low thermal expansion of polymers. Recently development of additive manufacturing also brings new opportunities to make polymer heat exchangers with desired design that was hard to realize before. However, due to the lower thermal conductivity polymer composite, the overall heat transfer performance is still a challenge in the polymer heat exchanger technology. In present work, a computational fluid dynamic (CFD) model has been developed to study the overall heat transfer performance of additively manufactured polymer heat exchangers. The CFD results offer an insight of fluid flow and temperature distribution in the polymer heat exchangers. This study provides a guidance not only on the polymer material selection but also on the design of polymer heat exchangers. The conclusions will be helpful to design a polymer heat exchanger whose overall heat transfer performance is comparable to a metal heat exchanger.

Zhang, Mingkan↗

NASA NTRS2005

MRI-Based Computational Fluid Dynamics in Experimental Vascular Models: Toward the Development of an Approach for Prediction of Cardiovascular Changes During Prolonged Space Missions

A priority of NASA is to identify and study possible risks to astronauts health during prolonged space missions [l]. The goal is to develop a procedure for a preflight evaluation of the cardiovascular system of an astronaut and to forecast how it will be affected during the mission. To predict these changes, a computational cardiovascular model must be constructed. Although physiology data can be used to make a general model, a more desirable subject-specific model requires anatomical, functional, and flow data from the specific astronaut. MRI has the unique advantage of providing images with all of the above information, including three-directional velocity data which can be used as boundary conditions in a computational fluid dynamics (CFD) program [2,3]. MRI-based CFD is very promising for reproduction of the flow patterns of a specific subject and prediction of changes in the absence of gravity. The aim of this study was to test the feasibility of this approach by reconstructing the geometry of MRI-scanned arterial models and reproducing the MRI-measured velocities using CFD simulations on these geometries.

Spirka, T. A.↗

NASA NTRSDate not supplied

Coupling a Computational Fluid Dynamics Model to a Spacecraft Thermal System Model for the DraMS Instrument Thermal Analysis

The Dragonfly Mass Spectrometer (DraMS) is an instrument on the Dragonfly mission, which will spend 7 years in deep space cruise before landing and operating on the surface of Titan. Vacuum thermal analyses are required for deep space cruise, and convection analyses are required for the Titan surface operations. Model exchanges across multiple thermal teams are needed for all phases of the mission. For DraMS, Thermal Desktop® (TD) has been the main thermal analytical tool of choice due to its capability in modeling complex thermal systems with relatively low computational power and for its availability across thermal teams. However, TD does not have computational fluid dynamics (CFD) capability and struggles to accurately capture complex convective behavior. DraMS has fans operating in tandem and gas flow behaviors are not easily predicted due to its complex flow paths. CFD software, such as Fluent, can model and predict such complex flow behaviors, but CFD models are computationally expensive, and its workflow processes are not tailored towards simulating large and complex systems. Therefore, a coupled modeling approach was chosen for DraMS: A TD model was used for simulating all the conductive, radiative, and source terms, while a Fluent CFD model was added on, as needed, to the TD model to provide the convective boundary conditions using the System Coupling software. The coupling software allows the TD and Fluent models to communicate data and arrive at a co-solved and co-converged solution. Furthermore, Thermal Iso-value Exchange (TIE) method was developed to facilitate and improve the TD-Fluent data exchange process. This paper will discuss the analytical studies that were done to verify the accuracy and usability of the coupled approach and the challenges associated, which lead to the development of the TIE approach. DraMS thermal design and co-solved analysis results will also be discussed.

Heat transfer↗

NASA NTRSDate not supplied

Coupling a Computational Fluid Dynamics (CFD) Model to a Spacecraft Thermal System Model for the DraMS Instrument Thermal Analysis

The Dragonfly Mass Spectrometer (DraMS) is an instrument on the Dragonfly mission, which will spend 7 years in deep space cruise before landing and operating on the surface of Titan. Vacuum thermal analyses are required for deep space cruise, and convection analyses are required for the Titan surface operations. Model exchanges across multiple thermal teams are needed for all phases of the mission. For DraMS, Thermal Desktop (TD) has been the main thermal analytical tool of choice due to its capability in modeling complex thermal systems with relatively low computational power and for its availability across thermal teams. However, TD does not have computational fluid dynamics (CFD) capability and struggles to accurately capture complex convective behavior. DraMS has fans operating in tandem and gas flow behaviors are not easily predicted due to its complex flow paths. CFD software, such as Fluent, can model and predict such complex flow behaviors, but CFD models are computationally expensive, and its workflow processes are not tailored towards simulating large and complex systems. Therefore, a coupled modeling approach was chosen for DraMS: A TD model was used for simulating all the conductive, radiative, and source terms, while a Fluent CFD model was added on, as needed, to the TD model to provide the convective boundary conditions using the System Coupling software. The coupling software allows the TD and Fluent models to communicate data and arrive at a co-solved and co-converged solution. Furthermore, Thermal Iso-value Exchange (TIE) method was developed to facilitate and improve the TD-Fluent data exchange process. This paper will discuss the analytical studies that were done to verify the accuracy and usability of the coupled approach and the challenges associated, which lead to the development of the TIE approach. DraMS thermal design and co-solved analysis results will also be discussed.

heat transfer↗

NASA NTRS2010

Computational Fluid Dynamics (CFD) Simulations of Jet Mixing in Tanks of Different Scales

For long-duration in-space storage of cryogenic propellants, an axial jet mixer is one concept for controlling tank pressure and reducing thermal stratification. Extensive ground-test data from the 1960s to the present exist for tank diameters of 10 ft or less. The design of axial jet mixers for tanks on the order of 30 ft diameter, such as those planned for the Ares V Earth Departure Stage (EDS) LH2 tank, will require scaling of available experimental data from much smaller tanks, as well designing for microgravity effects. This study will assess the ability for Computational Fluid Dynamics (CFD) to handle a change of scale of this magnitude by performing simulations of existing ground-based axial jet mixing experiments at two tank sizes differing by a factor of ten. Simulations of several axial jet configurations for an Ares V scale EDS LH2 tank during low Earth orbit (LEO) coast are evaluated and selected results are also presented. Data from jet mixing experiments performed in the 1960s by General Dynamics with water at two tank sizes (1 and 10 ft diameter) are used to evaluate CFD accuracy. Jet nozzle diameters ranged from 0.032 to 0.25 in. for the 1 ft diameter tank experiments and from 0.625 to 0.875 in. for the 10 ft diameter tank experiments. Thermally stratified layers were created in both tanks prior to turning on the jet mixer. Jet mixer efficiency was determined by monitoring the temperatures on thermocouple rakes in the tanks to time when the stratified layer was mixed out. Dye was frequently injected into the stratified tank and its penetration recorded. There were no velocities or turbulence quantities available in the experimental data. A commercially available, time accurate, multi-dimensional CFD code with free surface tracking (FLOW-3D from Flow Science, Inc.) is used for the simulations presented. Comparisons are made between computed temperatures at various axial locations in the tank at different times and those observed experimentally. The affect of various modeling parameters on the agreement obtained are assessed.

Breisacher, Kevin↗