Search NASA⌕ Search

SEARCH · Search NASA

Results for “dislocation density”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

Effect of dislocations on properties of heteroepitaxial InP solar cells

The apparently unrelated phenomena of temperature dependency, carrier removal and photoluminescence are shown to be affected by the high dislocation densities present in heteroepitaxial InP solar cells. Using homoepitaxial InP cells as a baseline, it is found that the relatively high dislocation densities present in heteroepitaxial InP/GaAs cells lead to increased volumes of dVoc/dt and carrier removal rate and substantial decreases in photoluminescence spectral intensities. With respect to dVoc/dt, the observed effect is attributed to the tendency of dislocations to reduce Voc. Although the basic cause for the observed increase in carrier removal rate is unclear, it is speculated that the decreased photoluminescence intensity is attributable to defect levels introduced by dislocations in the heteroepitaxial cells.

Weinberg, I.↗

Assessment of dislocation reduction on 100 mm diameter bulk GaN grown by the NEAT method

X-ray topography measurements on a 100 mm diameter GaN boule grown by the Near Equilibrium AmmonoThermal method revealed an improvement in dislocation density from >1 × 10 6 cm -2 to between 2 × 10 5 and 5 × 10 5 cm -2, an improvement greater than two to five times from seed to growth. This data builds on previous X-ray diffraction and defect selective etching to quantify the reduction in defect density that is closely associated with increasing growth thickness. This result indicates that there is a pathway to further dislocation reduction by increasing growth thickness for GaN crystals including those of 100 mm or larger diameter. Further reduction of the dislocation density of large-area substrates will lead to GaN power devices with reduced leakage current under reverse bias and better device performance.

36 MATERIALS SCIENCE↗

Single-crystal sapphire microstructure for high-resolution synchrotron X-ray monochromators

We report on the growth and characterization of several sapphire single crystals for the purpose of x-ray optics applications. Structural defects were studied by means of laboratory double-crystal X-ray diffractometry and white beam synchrotron-radiation topography. The investigations confirmed that the main defect types are dislocations. The best quality crystal was grown using the Kyropoulos technique with a dislocation density of 10 2 -10 3 cm -2 and a small area with approximately 2*2 mm 2 did not show dislocation contrast in many reflections and has suitable quality for application as a backscattering monochromator. As a result, a clear correlation between growth rate and dislocation density is observed, though growth rate is not the only parameter impacting the quality.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Part 1: Silicon ingot casting. Heat Exchanger Method (HEM)

Directional solidification by the Heat Exchanger Method (HEM) is a viable approach for directional solidification of silicon ingots used for terrestrial solar cell applications. Some of the significant advances made during this phase of the program were: ingot size, 34 cm x 34 cm x 17 cm - 45 kg, usable material yield - 90%, solar cell efficiency averaged over the whole ingot - 85% of control CZ (35 kg ingot), very uniform resistivity over the boule, and cycle time for 36 kg ingots - 56 hours. Some of the problems encountered were growth rate decrease with increased ingot height, silicon carbide precipitates, and high dislocation density in HEM material. The silicon carbide is attributed to backstreaming of oil vapors from the vacuum pump; the high dislocation density is associated with the thermal history of the boule.

Source record↗

A micro-alloyed ferritic steel strengthened by nanoscale precipitates

A ferritic steel with finely dispersive precipitates was investigated to reveal the fundamental strengthening mechanisms. The steel has a yield strength of 760 MPa, approximately three times higher than that of conventional Ti-bearing high strength hot-rolled sheet steels, and its ultimate tensile strength reaches 850 MPa with an elongation-to-failure value of 18%. Using energy dispersive X-ray spectroscopy (EDXS) and transmission electron microscope (TEM), fine carbides TiC with an average diameter of 10 nm were observed in the ferrite matrix of the 0.08%Ti steel, and some cubic M23C6 precipitates were also observed at the grain boundaries and the interior of the grains. The finely dispersive TiC precipitates in the matrix provide matrix strengthening. The estimated magnitude of precipitation strengthening is around 458 MPa, depending on the average size of the nanoscale precipitates. Dislocation densities increased from 3.42×1013 m-2 to 1.69 × 1014 m-2, respectively, with increasing tensile strain from 5.5% to 22%. The measured work-hardening behavior can be related to the observed dislocation accumulations resulting from the dispersive nano-scale precipitates.

36 MATERIALS SCIENCE↗

High energy X-ray characterization of the microstructure of PuGa alloy samples at macroscopic depths and non-ambient conditions

High energy (95 keV) X-rays were utilized to characterize the microstructure of eight PuGa alloy samples at room temperature and during cooling to ∼10 K. The samples had different Ga content (nominally 0-3.4 at.%), age, and history. A ninth sample, similarly characterized with neutron diffraction, was included to extend the Ga range to 7 at.%. The samples span the range from single phase α (monoclinic) to δ (face-centered cubic) PuGa, as well as a two-phase α′/δ sample. The crystallographic textures, phase fractions, lattice parameters and dislocation densities of each sample were evaluated through distinct analysis techniques. The textures of the samples were modest. In each case, the dislocation densities were relatively high, comparable to cold worked metals and metals exposed to similar radiation dose. At room temperature, the lattice parameters determined in the predominantly single-phase samples were larger than expected based on the nominal Ga concentration. The observed lattice thermal expansions of the single-phase δ samples to 10 K are self-consistent across the samples and consistent with previous measurements reported in the literature. Significantly larger thermal lattice strain is observed in the δ phase of the two-phase material due to mechanical constraint from the α′ phase, which has a three times larger thermal expansion and is much harder than the δ phase. In conclusion, the results demonstrate the unique value of high-energy X-rays for relatively routine microstructural characterization of Pu alloy samples.

36 MATERIALS SCIENCE↗

Concentration and relaxation depth profiles of In{sub x}Ga{sub 1-x}As/GaAs and GaAs{sub 1-x}P{sub x}/GaAs graded epitaxial films studied by x-ray diffraction

A method is proposed to determine the concentration and relaxation depth profiles in graded epitaxial films from x-ray reciprocal space maps (RSMs). Various approximations in the kinematical x-ray diffraction from epitaxial films with the misfit dislocation density depth profile are developed. We show that a symmetric and an asymmetric RSM, or two asymmetric RSMs, contain enough information to obtain the concentration, relaxation, and lattice tilt depth profiles without any additional assumptions. The proposed approach is applied to In{sub x}Ga{sub 1-x}As/GaAs and GaAs{sub 1-x}P{sub x}/GaAs epitaxial graded films. The reconstructed concentration and dislocation density depth profiles are found to be in an agreement with the ones expected from the growth conditions.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

In situ synchrotron tensile investigations on 14YWT, MA957, and 9-Cr ODS alloys

Advanced ODS alloys provide exceptional radiation tolerance and high-temperature mechanical properties when compared to traditional ferritic and ferritic/martensitic 9F/M) steels. Their remarkable properties result from ultrahigh density and ultrafine size of Y-Ti-O nanoclusters within the ferritic matrix. In this work, we applied a high-energy synchrotron radiation X-ray to study the deformation process of three advanced ODS materials including 14YWT, MA957, and 9-Cr ODS steel. Only the relatively large nanoparticles in the 9-Cr ODS were observed in the synchrotron X-ray diffraction. The nanoclusters in both 14YWT and MA957 were invisible in the measurement due to their non-stoichiometric nature. Due to the different sizes of nanoparticles and nanoclusters in the materials, the Orowan looping was considered to be the major strengthening mechanism in the 9-Cr ODS, while the dispersed-barrier-hardening is dominant strengthening mechanism in both 14YWT and MA957, This analysis was inferred from the different build-up rates of dislocation density when plastic deformation was initiated. Finally, the dislocation densities interpreted from the X-ray measurements were successfully modeled using the Bergstrom's dislocation models. (C) 2016 Elsevier B.V. All rights reserved.

Lin, Jun-Li↗

Dislocation dynamics of web type silicon ribbon

Silicon ribbon grown by the dendritic web process passes through a rapidly changing thermal profile in the growth direction. This rapidly changing profile induces stresses which produce changes in the dislocation density in the ribbon. A viscoplastic material response function (Haasen-Sumino model) is used herein to calculate the stresses and the dislocation density at each point in the silicon ribbon. The residual stresses are also calculated.

Dillon, O. W., Jr.↗

In Situ Synchrotron Tensile Investigations on 14YWT, MA957 and 9-Cr ODS Alloys

Nanostructured ferritic alloys (NFAs) provide exceptional radiation tolerance and high-temperature mechanical properties when compared to traditional ferritic and ferritic/martensitic (F/M) steels. Their remarkable properties result from ultrahigh density and ultrafine size of Y-Ti-O nanoclusters within the ferritic matrix. In this work, we applied a high-energy synchrotron radiation X-ray to study the deformation process of two NFAs including 14YWT and MA957, and a 9-Cr ODS steel. Only the relatively large nanoparticles in the 9-Cr ODS were observed in the synchrotron X-ray diffraction. The nanoclusters in both 14 YWT and MA957 were invisible in the measurement due to their non-stoichiometric nature. Due to the different sizes of nanoparticles and nanoclusters in the materials, the Orowan looping was considered to be the major strengthening mechanism in the 9-Cr ODS, while the dispersed-barrier-hardening is dominant strengthening mechanism in both 14YWT and MA957, respectively. This analysis was inferred from the different build-up rates of dislocation density when plastic deformation was initiated. Finally, the dislocation densities interpreted from the X-ray measurements were successfully modeled using the Bergstr m s dislocation models.

Lin, Jun-Li↗

Microstructure-sensitive modeling of high temperature creep in grade-91 alloy

Predicting the effects of microstructure on high-temperature creep responses of steel components is critical to minimize the risks of failure and maximize economic viability in the energy sector. In this research, a recently developed advanced mechanistic constitutive model is employed to study the effect of microstructure on the creep responses and to rationalize experimentally reported variability in the performances of grade-91 alloy. Hundreds of experimental creep tests from the literature are used to assess the predictability of the model. The model proposed is shown to accurately predict the steady-state creep rates and also the less commonly considered, yet important, primary-to-secondary transients for a wide range of creep conditions. Further, the model is capable of extrapolating the creep response of grade 91 alloy even outside of the calibration regime. Using this model, the roles of initial microstructure described in terms of grain size, dislocation density, and precipitate content, on the creep responses are investigated. The effect of initial microstructure on the steady-state creep rates and creep-strain is found to vary with stress and temperature. Grain size plays a significant role in the low-stress creep, where the diffusional creep is dominant. On the other hand, the effects of dislocation densities and precipitate content are significant in the dislocation-plasticity-dominated high-stress and temperature regimes. Furthermore, by comparing model predictions against a large experimental creep database, it is found that variability in the creep responses can be rationalized on the basis of differences in the initial microstructure. Overall, this work provides a robust pathway for microstructure-aware engineering design, verification, and validation of metallic components for energy applications.

36 MATERIALS SCIENCE↗

Coalescence of GaP on V-Groove Si

In recent years, better understanding and control over the formation of crystalline defects during the direct epitaxy of III-V semiconductors on Si substrates via metal organic vapor phase epitaxy (MOVPE) has enabled large gains in III-V-on-Si solar cell efficiency, pointing to pathway to lower-cost, high-performance III-V solar cells. However, such results have only been achieved on costly chemo-mechanically-polished (CMP) Si wafers. The use of V-groove nanopatterned Si substrates has demonstrated similarly high-crystalline-quality III-V-on-Si epitaxy, but also can be combined with lower-cost polishing techniques. Although they offer a potential cost advantage, growth on V-groove substrates adds challenges not present for epitaxy on planar wafers (the III-V material must be coalesced into a thin film after an initial nucleation stage). MOVPE growth conditions that promote highly facet-selective lateral growth needed for coalescence are generally actively avoided for conventional thin fim growth, so growth conditions need to be re-developed for V-groove-based epitaxy. Additionally, coalescence add complexity to the dislocation dynamics related to lattice relaxation, so strategies used to keep threading dislocation density (TDD) low on planar substrates need to be re-tuned for V-grooves. We have studied the morphological evolution and dislocation dynamics of GaP grown on V-groove Si by MOVPE. Growth conditions of V/III=5,000 and Tg=800 degrees C were uniquely found to produce extremely smooth coalesced thin films, with an RMS roughness of 0.2 nm measured by AFM. Additionally, at this growth condition, we identified two regimes of growth determined by the width of the SiNx cap (a remnant of the nanopatterning process) at the top of the V-grooves. For narrow caps, the GaP coalesces into a thin film, and for wide caps, the GaP evolves into {1 1 1}-faceted diamonds that do not coalesce. We suggest the influence of Si from the sidewalls of the V-grooves on the surface reconstruction of the GaP as the mechanism for this effect, with reflection difference spectroscopy (RDS) and Si doping experiments supporting this theory. In addition to morphology, the dislocation dynamics of the system were studied with electron channeling contrast imaging (ECCI) and transmission electron microscopy (TEM). The TDD of the coalesced GaP films was found to be 5 x 10^7 cm^-2 after coalescence via ECCI, a level still too high for high-quality solar cells. However, misfit dislocations crossing multiple grooves greater than 20 micrometers long were observed in ECCI, suggesting that the V-grooves do not block dislocation glide. TEM prior to and after coalescence was used to distinguish between dislocation creation driven by growth conditions and coalescence. Finally, strategies to reduce the dislocation density to levels acceptable for solar cells will be discussed.

GaP↗

Gradient Plasticity Model and its Implementation into MARMOT

The influence of strain gradient on deformation behavior of nuclear structural materials, such as body-centered cubic (bcc) iron alloys has been investigated. We have developed and implemented a dislocation based strain gradient crystal plasticity material model. A mesoscale crystal plasticity model for inelastic deformation of metallic material, bcc steel, has been developed and implemented numerically. Continuum Dislocation Dynamics (CDD) with a novel constitutive law based on dislocation density evolution mechanisms was developed to investigate the deformation behaviors of single crystals, as well as polycrystalline materials by coupling CDD and crystal plasticity (CP). The dislocation density evolution law in this model is mechanism-based, with parameters measured from experiments or simulated with lower-length scale models, not an empirical law with parameters back-fitted from the flow curves.

continuous dislocation dynamics↗

Chromium doping effects on structural and dielectric properties of Mn-Zn cobaltites

The effect of transition metal Cr{sup 2+} ion as a dopant of Zn{sup 2+} in Mn{sub 0.5}Zn{sub 0.5}Co{sub 2}O{sub 4} is investigated. Co-doped Mn{sub 0.5}Zn{sub 0.5-x}Cr{sub x}Co{sub 2}O{sub 4} (x = 0, 0.3 and 0.5) cobaltites were prepared by solid-state reaction route. X-ray powder diffraction (XRD) analysis reveals that the samples prepared are polycrystalline single-phase cubic spinel in structure having a space group Fd3m. An increase in average particle size observed with Cr{sup 2+} doping. However other structural parameters such as X-ray density, micro strain and dislocation density shows almost a similar decreasing trend with increase in Cr{sup 2+}. High value of permittivity ∼10{sup 5} is observed for the parent Mn{sub 0.5}Zn{sub 0.5}Co{sub 2}O{sub 4} and shows a substantial decrease with increase in the Cr{sup 2+} doping. Higher doping of Cr{sup 2+} also increases the dielectric loss and hence limits its technological importance. At lower frequencies ac conductivity has been found to increase with increase in Cr{sup 2+} content.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Dislocation dynamics during the growth of silicon ribbon

The thermal viscoplastic stresses and the dislocation densities in silicon ribbon are computed for an axially changing thermal profile by using an iterative finite difference method. A material constitutive equation (Haasen-Sumino model) which involves an internal variable (mobile dislocation density) is used. The results are interpreted as showing that there is a maximum width of silicon ribbon that can be grown when viscoplasticity and dislocations are considered. This maximum width limitation does not exist if the material behavior is elastic.

Dillon, O. W., Jr.↗

The impact of nickel concentration and stacking fault energy on deformation mechanisms in high-purity austenitic Fe-Cr-Ni alloys

Understanding how composition affects deformation mechanisms in austenitic stainless steels is essential for developing accurate predictive models of stress-induced failures and stress corrosion cracking. Nickel (Ni), an element classified as a critical element, plays a crucial role in these processes. It is important to examine how Ni concentration influences stacking fault energy (SFE) and, consequently, the deformation mechanisms of austenitic stainless steels. However, in commercial stainless steels, the effects of other alloying elements and impurities can obscure Ni's role, complicating efforts to isolate its impact. Here, in this study, we use two high-purity Fe-Cr-Ni alloys to investigate how Ni concentration and SFE interact to alter deformation mechanisms and induce martensitic transformation. By combining in situ synchrotron X-ray diffraction (XRD) tensile testing and post-mortem electron microscopy with density functional theory simulations, we gain precise insights into these phenomena. We find that the Fe18Cr10Ni (wt%) alloy, with its low SFE, exhibits higher stacking fault probability, deformation-induced martensitic transformation, and a lesser increase in dislocation density with plastic strain. In contrast, the Fe18Cr14Ni (wt%) alloy, with its higher SFE, shows enhanced deformation twinning and greater dislocation density with increasing strain. These findings from high-purity ternary alloys provide valuable insights that can guide the search for alternative elements to replace Ni while achieving similar effects on phase stability and deformation behavior.

36 MATERIALS SCIENCE↗

Structure And Radiation Damage Behavior Of Epitaxial CrxMo1-x Alloy Thin Films On MgO

Phenomena related to the interaction of point defects and dopants with grain boundaries and interfaces have been very well documented. However, a quantitative understanding of such an interaction is still missing. In this paper we explore the correlation between radiation damage and interface structure. In doing so, CrxMo1-x(001) films of thickness ~100 nm were epitaxially grown on MgO (001) using molecular beam epitaxy. The interface dislocation density can be systematically varied by controlling the composition of the film. This system allows us to probe the response of the defects generated during the irradiation to the interface dislocation density. The microstructural features of these films before and after irradiation are carefully studied using high resolution scanning/transmission electron microscopy and electron diffraction. It has been found that the film/substrate system is very resistant to ion-induced irradiation damage. No visible point defect clusters, dislocation network or amorphization has been identified, which is contrasted with other materials of either metallic or ionic bonding. We conclude that the defects in the present system appear to be either sub-microscopic and highly dispersed or are annihilated during the irradiation process. Further detailed work is needed to identify the spatial distribution of the defects.

Environmental Molecular Sciences Laboratory↗

Effect of emitter parameter variation on the performance of heteroepitaxial indium phosphide solar cells

Metallorganic chemical-vapor-deposited heteroepitaxial indium phosphide (InP) solar cell experimental results were simulated by using a PC-1D computer model. The effect of emitter parameter variation on the performance of n(+)/p/p(+) heteroepitaxial InP/GaAs solar cell was presented. The thinner and lighter doped emitters were observed to offer higher cell efficiencies. The influence of emitter thickness and minority carrier diffusion length on the cell efficiency with respect to dislocation density was studied. Heteroepitaxial cells with efficiencies similar to present day homojunction InP efficiencies (greater than 16 percent AMO) were shown to be attainable if a dislocation density lower than 10(exp 6)/sq cm could be achieved. A realistic optimized design study yielded InP solar cells of over 22 percent AMO efficiency at 25 C.

Jain, Raj K.↗