Search NASA⌕ Search

SEARCH · Search NASA

Results for “elastomer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS2000

Polymer-Oxygen Compatibility Testing: Effect of Oxygen Aging on Ignition and Combustion Properties

The oxygen compatibility of six polymers used in oxygen service was evaluated after exposure for 48 hours to oxygen pressures ranging from 350 to 6200 kPa (50 to 900 psia), and temperatures ranging from 50 to 250 C (122 to 302 F). Three elastomers were tested: CR rubber (C873-70), FKM fluorocarbon rubber (Viton A), and MPQ silicone rubber (MIL-ZZ-765, Class 2); and three thermoplastics were tested: polyhexamethylene adipamide (Zytel 42), polytetrafluoroethylene (Teflon TFE), and polychlorotrifluoroethylene (Neoflon CTFE M400H). Post-aging changes in mass, dimensions, tensile strength, elongation at break, and durometer hardness were determined. Also, the compression set was determined for the three elastomers. Results show that the properties under investigation were more sensitive to oxygen pressure at low to moderate temperatures, and more sensitive to temperature at low to moderate oxygen pressures. Inspection of the results also suggested that both chain scissioning and cross-linking processes were operative, consistent with heterogeneous oxidation. Attempts are underway to verify conclusively the occurrence of heterogeneous oxidation using a simple modulus profiling technique. Finally, the effect of aging at 620 kpa (90 psia) and 121 C (250 F) on ignition and combustion resistance was determined. As expected, aged polymers were less ignitable and combustible (had higher AlTs and lower heats of combustion). Special attention was given to Neoflon CTFE. More specifically, the effect of process history (compression versus extrusion molding) and percent crystallinity (quick- versus slow-quenched) on the AIT, heat of combustion, and impact sensitivity of Neoflon CTFE was investigated. Results show the AIT, heat of combustion, and impact sensitivity to be essentially independent of Neoflon CTFE process history and structure.

Waller, Jess M.↗
NASA NTRS2006

Elastomeric Seal Development for Advanced Docking/Berthing System

Elastomeric seals ar Elastomeric seals are being considered for application to the Advanced Docking / Berthing System. Currently, three candidate elastomers are being evaluated. To meet the unique requirements of the ADBS, several test fixtures have been built to determine each elastomer s Environmental and operating temperature compatibility Material stability when exposed to Atomic Oxygen and Ultraviolet radiation Adhesion force required to separate Compression set Leak rate These results will be compared with those from the metallic seal development to determine the final seal design

Daniels, Christopher↗
NASA NTRS1978

Oil Saving Seal

Driven under difficult field conditions, the Army Jeep shown went more than 22,000 miles without an oil change in a test conducted by the U.S. Army Mobility Equipment Research and Development Command. Key to this exceptionally long oil life was a set of piston ring seals made of a new synthetic rubber formula called RC-34; the seal pictured, photographed after its arduous Army trial, shows no signs of deterioration. The seal and the RC-34 material, which may soon be available for use in the family auto, were developed by Ramsey Corporation, St. Louis, Missouri, a division of TRW Automotive Worldwide. The oil in an automobile engine must be I replaced every few thousand miles not because it wears out but because it becomes contaminated. The contamination sources are gasoline and combustion gases which blow by the piston rings to mix with the oil, reducing the oil's ability to lubricate properly. Seeking to prolong oil life by eliminating "blowby," Ramsey Corporation looked for a better way to seal piston rings and used NASA technology as a departure point. The parent company TRW, under contract to NASA's Jet Propulsion Laboratory, had developed seals and bladders from a type of material called elastomers which where designed to withstand the environmental extremes of interplanetary flight. That effort formed a knowledge base for research which culminated in Ramsey's RC-34 elastomer.

Source record↗
NASA NTRS2007

Assessing MMOD Impacts on Seal Performance

The elastomer seal needed to seal in cabin air when NASA s Crew Exploration Vehicle is docked is exposed to space prior to docking. While open to space, the seal might be hit by orbital debris or meteoroids. The likelihood of damage of this type depends on the size of the particle. Our campaign is designed to find the smallest particle that will cause seal failure resulting in loss of mission. We will then be able to estimate environmental risks to the seal. Preliminary tests indicate seals can withstand a surprising amount of damage and still function. Collaborations with internal and external partners are in place and include seal leak testing, modeling of the space environment using a computer code known as BUMPER, and hypervelocity impact (HVI) studies at Caltech. Preliminary work at White Sands Test Facility showed a 0.5 mm diameter HVI damaged areas about 7 times that diameter, boring deep (5 mm) into elastomer specimens. BUMPER simulations indicate there is a 1 in 1440 chance of getting hit by a particle of diameter 0.08 cm for current Lunar missions; and 0.27 cm for a 10 year ISS LIDS seal area exposure.

deGroh, Henry C., III↗
NASA NTRS2011

Fire-Retardant Polymeric Additives

Polyhydroxyamide (PHA) and polymethoxyamide (PMeOA) are fire-retardant (FR) thermoplastic polymers and have been found to be useful as an additive for imparting fire retardant properties to other compatible, thermoplastic polymers (including some elastomers). Examples of compatible flammable polymers include nylons, polyesters, and acrylics. Unlike most prior additives, PHA and PMeOA do not appreciably degrade the mechanical properties of the matrix polymer; indeed, in some cases, mechanical properties are enhanced. Also, unlike some prior additives, PHA and PMeOA do not decompose into large amounts of corrosive or toxic compounds during combustion and can be processed at elevated temperatures. PMeOA derivative formulations were synthesized and used as an FR additive in the fabrication of polyamide (PA) and polystyrene (PS) composites with notable reduction (>30 percent for PS) in peak heat release rates compared to the neat polymer as measured by a Cone Calorimeter (ASTM E1354). Synergistic effects were noted with nanosilica composites. These nanosilica composites had more than 50-percent reduction in peak heat release rates. In a typical application, a flammable thermoplastic, thermoplastic blend, or elastomer that one seeks to render flame-retardant is first dry-mixed with PHA or PMeOA or derivative thereof. The proportion of PHA or PMeOA or derivative in the mixture is typically chosen to lie between 1 and 20 weight percent. The dry blend can then be melt-extruded. The extruded polymer blend can further be extruded and/or molded into fibers, pipes, or any other of a variety of objects that may be required to be fire-retardant. The physical and chemical mechanisms which impart flame retardancy of the additive include inhibiting free-radical oxidation in the vapor phase, preventing vaporization of fuel (the polymer), and cooling through the formation of chemical bonds in either the vapor or the condensed phase. Under thermal stress, the cyclic hydroxyl/ methoxy component forms polybenzoxazole (PBO) in a reaction that absorbs heat from its surroundings. PBO under thermal stress cross-links, forming a protective char layer, which thermally insulates the polymer. Thus, the formation of the char layer further assists to extinguish the fire by preventing vaporization of the polymeric fuel.

Williams, Martha K.↗
NASA NTRS2015

Elastomeric Seal Performance after Terrestrial Ultraviolet Radiation Exposure

Ultraviolet radiation was evaluated to determine its negative effects on the performance of elastomeric gas pressure seals. The leak rates of the silicone elastomer S0383-70 O-ring test articles were used to quantify the degradation of the seals after exposure to vacuum-ultraviolet and/or middle-to-near-ultraviolet wavelength radiation. Three groups of seals were exposed in terrestrial facilities to 115-165 nm wavelength radiation, 230-500 nm wavelength radiation, or both spectrums, for an orbital spaceflight equivalent of 125 hours. The leak rates of the silicone elastomer S0383-70 seals were quantified and compared to samples that received no radiation. Each lot contained six samples and statistical t-tests were used to determine the separate and combined influences of exposure to the two wavelength ranges. A comparison of the mean leak rates of samples exposed to 115-165 nm wavelength radiation to the control specimens showed no difference, suggesting that spectrum was not damaging. The 230-500 nm wavelength appeared to be damaging, as the mean leak rates of the specimens exposed to that range of wavelengths, and those exposed to the combined 115-165 nm and 230-500 nm spectrums, were significantly different from the leak rates of the control specimens. Most importantly, the test articles exposed to both wavelength spectrums exhibited mean leak rates two orders of magnitude larger than any other exposed specimens, which suggested that both wavelength spectrums are important when simulating the orbital environment.

leakage↗
NASA NTRS2017

Relationship of Cure Temperature to Mechanical, Physical, and Dielectric Performance of PDMS Glass Composite for Electric Motor Insulation

Achieving NASAs aggressive fuel burn and emission reduction for N-plus-3 aircraft will require hybrid electric propulsion system in which electric motors driven by either power generated from turbine or energy storage system will power the fan for propulsion. Motors designed for hybrid electric aircraft are expected to operate at medium to high voltages over long durations in a high altitude service environment. Such conditions have driven research toward the development of wire insulation with improved mechanical strength, thermal stability and increased breakdown voltage. The silicone class of materials has been considered for electric wire insulation due to its inherent thermal stability, dielectric strength and mechanical integrity. This paper evaluates the dependence of these properties on the cure conditions of a polydimethyl-siloxane (PDMS) elastomer; where both cure temperature and base-to-catalyst ratio were varied. The PDMS elastomer was evaluated as a bulk material and an impregnation matrix within a lightweight glass veil support. The E-glass support was selected for mechanical stiffness and dielectric strength. This work has shown a correlation between cure conditions and material physical properties. Tensile strength increased with cure temperature whereas breakdown voltage tended to be independent of process variations. The results will be used to direct material formulation based on specific insulation requirements.

insulation↗
DOE OSTI2024

Adaptive materials and systems for manipulation of electromagnetic radiation

Fully artificial, adaptive composite materials and systems, having variable transmittance, reflectance, and/or absorptance to radiation in visible, infrared, or other desired region of the electromagnetic spectrum, and methods of the manufacture and use thereof are provided. The adaptive composite materials and systems possess an unprecedented combination of properties and are, therefore, poised to enable a broad range of practical applications. The adaptive composite material incorporates at least one size-variable active area having a variable transmittance, reflectance, and/or absorptance in at least a portion of the electromagnetic spectrum and comprises at least: an elastomer substrate, a texturizing layer disposed on top of the substrate, and an optional reflective coating disposed on top of the texturizing layer. In operation, the stretching and relaxation of the elastomer substrate causes changes in the surface morphology of the texturized layers (e.g., the change in the size and depth of surface features in the texturizing layer), this in turn results in the increased or decreased transmittivity, reflectivity, and/or absorptivity of the active area.

Gorodetsky, Alon A.↗
DOE OSTI2024

Novel Fast Cure Silicone Inks for Single-Step, Support-Free 3D Printing of Tall, Overhanging, and High Aspect Ratio Structures

Silicone elastomers have a broad variety of applications, such as soft robotics, biomedical devices, and structural metamaterials. The extrusion-based method known as direct ink write (DIW) has enabled the production of additively manufactured silicone structures. However, this method is limited to manufacturing mostly planar or pseudo-3D structures. Due to the low self-supporting capabilities of extruded strands for traditional silicone-based “inks,” obtaining tall or overhanging structures, or structures comprised by thin walls is not feasible. Here, in this study, a novel Fast Cure silicone-based ink is demonstrated that enables manufacturing of complex 3D structures. The Fast Cure ink is a two-part mixture and silicone structures are produced by inline mixing and coextrusion of a part containing a catalyst (part A) and a part containing a crosslinker (part B). By the virtue of crosslinking, the extruded strands rapidly rigidize, increasing their self-supportive capacity. Hence, structures can be obtained with superior shape retention and previously unobtainable parts are realized that are tall, with aspect ratios higher than 3, and have overhanging features, achieving inclination angles smaller than 35° with respect to the printing plane. These minimal sag parts are achieved without requiring extra curing or mechanisms, support structures, or suspension baths.

36 MATERIALS SCIENCE↗
NASA NTRS1967

Polymer research

Stress-strain distribution in elastomers, and chemical and physical properties of prepolymers, rigid urethane foam, and thermoplastic rubbers for composite solid propellant binders

ELASTOMER↗
NASA NTRS2003

Training with the International Space Station interim resistive exercise device

A unique, interim elastomer-based resistive exercise device (iRED) is being used on the International Space Station. PURPOSE: This study characterized iRED training responses in a 1-g environment by: 1) determining whether 16 wk of high-intensity training with iRED produces increases in muscle strength and volume and bone mineral density (BMD), 2) comparing training responses with iRED to free weights, and 3) comparing iRED training responses at two training volumes. METHODS: Twenty-eight untrained men were assigned to four groups of seven subjects each: a no exercise control group (CON), an iRED group who trained with three sets/exercise (iRED3), a free-weight group (FW) who trained with three sets/exercise, and an iRED group who trained with six sets/exercise (iRED6). Training exercises included squat (SQ), heel raise (HR), and dead lift (DL) exercises, 3 d.wk(-1) for 16 wk. RESULTS: For CON, no changes occurred pre- to posttraining. For iRED3, increases (P< or =0.05) in one-repetition maximum (1-RM) strength (SQ 21 +/- 4%, HR 17 +/- 4%, DL 29 +/- 5%), leg lean mass (3.1 +/- 0.5%) by dual energy x-ray absorptiometry (DXA), and thigh (4.5 +/- 0.9%) and calf (5.9 +/- 0.7%) muscle volume (by magnetic resonance imaging) occurred after training with no changes in BMD (DXA). For FW, increases in 1-RM strength (SQ 22 +/- 5%, HR 24 +/- 3%, DL 41 +/- 7%), whole body (3.0 +/- 1.1%) and leg lean mass (5.4 +/- 1.2%), thigh (9.2 +/- 1.3%) and calf (4.2 +/- 1.0%) muscle volumes, and lumbar BMD (4.2 +/- 0.7%) occurred after training. For iRED6, all responses were similar to iRED3. CONCLUSION: High-intensity training with the iRED produced muscle responses similar to FW but was not effective in stimulating bone. Bed rest and spaceflight studies are needed to evaluate the effectiveness of the iRED to prevent microgravity deconditioning.

Weight-Bearing/physiology↗
DOE OSTI2025

Conductive Liquid Metal Vitrimer Composites for Reconfigurable and Recyclable Flexible Electronics

Liquid metal (LM) elastomer composites exhibit excellent functionality for stretchable electronics and wearables, but limited recycling and reuse pathways constrain their sustainable use. Here, to address these challenges amid growing concerns over electronic waste, a conductive LM–vitrimer composite is presented that enables recyclable and reconfigurable electronics. This soft and stretchable composite features uniformly distributed LM inclusions that enhance thermal conductivity by 6.53× and enable the formation of conductive traces with electrical self-healing, while the vitrimer provides structural restoration. The dynamic covalent bonds of the vitrimer matrix are leveraged for both reprocessing the composite and chemically recovering 94% of the LM. This liquid-state filler slightly reduces the vitrimer's stiffness to 2.63 MPa (≈20% lower), while maintaining its high stretchability (>135% strain) and thermal stability. It is further examined how ultrasonicated LM inclusions interact with the vitrimer matrix and demonstrate the composite's self-healing and recyclability through two distinct approaches: 1) thermomechanical reprocessing, which restores fragmented composites under heat and compression for circuit reconfiguration; and 2) chemical recycling, which recovers the embedded LM for reuse in fabricating new composites and redesigned circuitry. With the integration of recyclability and diverse functional capabilities, LM–vitrimer composites emerge as a promising material platform for sustainable, flexible electronics.

Han, Youngshang [Univ. of Washington, Seattle, WA ↗
DOE OSTI2024

Hierarchical Composites Patterned via 3D Printed Cellular Fluidics

Additive manufacturing of freeform structures containing multiple materials with deterministic spatial arrangement and interactions remains a challenge for most 3D printing processes, due to complex fabrication tool requirements and limitations in printability of some material classes. Here, in this paper, a versatile method is reported to produce architected composites using the concept of cellular fluidics, in which lattices of unit cells are used as templating scaffolds to guide flowable infill materials in a programmed spatial pattern, upon which they are cured in place to produce a deterministically ordered multimaterial solid. The lattice design relies on the unit cell size, type, strut diameter, surface wetting, and distribution of cellular structures to control liquid flow and retention. Individual unit cells are tuned to achieve reliable infilling and combined into higher-order architectures to achieve multiscale composite materials with disparate mechanical properties, including those considered non-printable. Lattice design considerations for leveraging capillary phenomena and demonstrate several methods of patterning polymers in 3D-printed cellular fluidic structures are presented. The concept of tuning the compressive response of an architected composite using a flexible-elastomer as the lattice and a stiff-epoxy as the infill material is illustrated.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Helical Photonic Metamaterials for Encrypted Chiral Holograms

Helical structures are among the most quintessential three-dimensional (3D) forms that exhibit mirror asymmetry, a hallmark of chirality. Various structural parameters of helices directly linked to chiroptical properties highlight their importance as essential optical metamaterials for polarization-resolved sensors, imaging, and spectroscopies. However, such function-defining properties remain incompletely understood due to fabrication challenges and the lack of a relationship between structure and optical properties. Here, helical structures are analyzed parametrically, and correlations are established that are applicable to the design of chiral helical optical metamaterials. By systematically varying independent parameters—such as from single-turn to five-turn helices and from small major radii to larger ones optimized to fit the unit cell—the underlying relationships with ellipticty are revealed. In addition to theoretical modeling, the findings are experimentally validated using 3D printing and terahertz spectroscopy. The results demonstrate that optimized helical structures are mechanically tunable and exhibit unprecedented optical properties, including broadband and high-magnitude ellipticity spectra. Being embedded in soft elastomers, helical arrays can serve as soft, stretchable optical-mechanical sensors and holograms containing encoded information, such as barcodes and quick response (QR) codes. Chiral QR codes are realized using pixelated single helices with different handedness, demonstrating their potential as advanced encryption/decryption systems for security applications and chiral metaholograms.

Encrypted QR codes↗