Search NASA⌕ Search

SEARCH · Search NASA

Results for “electrode microstructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

Rheological and microstructural characterization of aqueous suspensions of carbon black and reduced graphene oxide

Carbon black is often used as a conductivity enhancer in battery electrodes. Reduced graphene oxide is another conducting material, with a high aspect ratio sheet-like morphology, and offers the possibility of generating a conducting network at loadings that are small compared to carbon black. Suspensions of conducting carbon, active materials and binders are typically coated on current collectors during the formation of electrodes. The rheology of these suspensions is an important indicator of the connectivity of particles in the suspension and impacts the electrical conductivity as well as the thickness of the coated layer. In this work, the rheology and microstructures of aqueous suspensions of para-aminobenzoic acid terminated carbon black (CB) with and without reduced graphene oxide (RGO) were investigated. The CB loading varied between 0.05 wt.% -10 wt.%, while the samples containing RGO had an RGO loading of 0.05 wt.%. The pH of the suspension was varied from 7.5 to 3. The carboxyl groups on the CB surface are deprotonated at pH 7.5, making the particles hydrophilic. Protonation of the carboxylate groups at pH 3 makes the particles partially hydrophobic. Suspensions of CB showed Newtonian behavior at all loadings for pH 7.5, and at loadings below 1.5 wt.% for pH 3. They are shear thinning at loadings between 1.5–10 wt.%. Interestingly, the low shear viscosity is non-monotonic with CB loading, rising up to a CB loading of 7.5 wt.%, and then dropping at 10 wt.%. Cryogenic scanning electron microscopy (SEM) showed CB particles forming aggregates at pH 3 for CB loadings greater than 1.5 wt.%. At pH 3, addition of 0.05 wt.% RGO resulted in a viscosity increase for suspensions containing 0.5 wt.% CB, as the RGO formed connections with CB particles that enhanced network formation. Adding RGO had little effect on suspensions that had 1.5 wt.% CB. The combination of SEM imaging and suspension rheology provides insight into the particle connectivity for the carbon-based materials studied here. These insights will be useful in determining coating conditions for slurries used in rechargeable battery electrodes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Highly crystalline sodium manganese ferrocyanide microcubes for advanced sodium ion battery cathodes

The microstructure and morphology of the crystal play an important role in the physical and electrochemical properties of electrode materials. Here we report a highly crystalline microcube structure of Na-rich Prussian white Na 1.92 Mn[Fe(CN) 6 ] 0.98 for sodium ion battery cathodes. The obtained structure features high crystallinity of the monoclinic structure with an average cubic size of 3–5 μm. Because of the improvement on microstructural and electrical properties, the cathode design enables promising electrochemical performance. The electrode exhibits an outstanding rate performance with reversible capacities of 152.8 mA h g –1 (10 mA g –1 ), 128.1 mA h g –1 (100 mA g –1 ), 118.7 mA h g –1 (500 mA g –1 ) and 110.3 mA h g –1 (1000 mA g –1 ). It also exhibits a good cycling performance with a capacity retention of 82% after 500 cycles at 100 mA g –1 . More importantly, the XRD analysis reveals a highly reversible monoclinic–cubic–monoclinic structural evolution of the cathode upon Na + extraction/insertion. The good rate and cycling performance can be attributed to the robust crystal structure with few defects and fast Na + transfer kinetics. The high purity single crystal morphology can also reduce the side reactions on the electrode/electrolyte interface.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Development of Stable Solid Oxide Electrolysis Cells for Low-Cost Hydrogen Production

The project objective was to demonstrate a solid oxide cell-based steam electrolysis stack that exhibits robustness, reliability, endurance, hydrogen purity, and produces hydrogen at elevated pressure of 2 to 3 bar. Innovative materials and processing methods were evaluated to improve degradation characteristics. Performance improvement focused on nearly all layers involved in the cell and stack assembly. Primary attention was paid to zirconia-ceria interface resistance control via sintering optimization and decrease in degradation from the oxygen electrode by evaluating low strontium (Sr) or Sr-free composition for both the oxygen electrode and current collection layer. Stack robustness was addressed by validating redox tolerance of fuel electrode, confirming capability of cells to survive repeated thermal cycles, studying the effect of pressure on performance and degradation, evaluating the effect of contamination on fuel and oxygen electrode performance and degradation, and identifying mitigation strategies to improve performance. The characterization included evaluation of electrochemical performance and stability followed by microstructural analysis. At the cell level, performance and stability improvements were achieved by incorporating a Sr-free oxygen electrode and a denser oxygen electrode barrier layer. At the stack level, pressurized operation reduces demand on first stage compression, the redox tolerant fuel electrode mitigates risk from service interruptions, and improvements to interconnect coating alleviate chromium (Cr) contamination effects. The denser barrier layer was achieved by adding a sintering aid to the samaria-doped ceria (SDC) composition that reduced sintering temperature by 150 °C. The resulting density was on par with the baseline SDC barrier layer density and the lower sintering temperature resulted in less resistive phase formation during sintering. Button cell tests did not demonstrate a change in performance when exposed to silicon (Si) or manganese (Mn) impurities to the fuel electrode and Cr impurity to the oxygen electrode. More detailed study however is warranted. The project addressed SOEC performance and stability at the cell and stack levels through a systematic approach to known sources of degradation that were combined and tested in three stack tests using an electrolyte supported cell design to allow for evaluation of a variety of fuel and oxygen electrode compositions. STK-82 and STK-83 had identical compositions. STK-100 incorporated the best materials and processing variables developed under this and concurrent projects, and was tested at elevated pressure in steam electrolysis. • STK-82 recovered performance after redox and thermal cycling, demonstrating the robustness of the stack and seals. It exhibited stable performance in testing for 500 hours in SOEC mode, followed by 300 hours of cycling between SOEC and SOFC tests. Degradation during SOEC operation was 1.8 %/ 1,000 hours. • STK-83 generated hydrogen at >80% steam conversion, and oxygen above 98.5 % purity during pressurized operation. Both hydrogen and oxygen were generated at 3 barg pressure without the use of a pressure vessel. In addition to balanced pressure, electrolysis operation at 1 bar differential pressure across anode and cathode was also demonstrated to substantial the robustness of the cell and seal. • STK-100 measured at initial ambient pressure conditions showed an area specific resistance of 1.1 ohm-cm 2 , and STK-83 had 1.3 ohm-cm 2 .

08 HYDROGEN↗

Materials Science of Electrodes and Interfaces for High-Performance Organic Photovoltaics

The science of organic photovoltaic (OPV) cells has made dramatic advances over the past three years with power conversion efficiencies (PCEs) now reaching ~12%. The upper PCE limit of light-to-electrical power conversion for single-junction OPVs as predicted by theory is ~23%. With further basic research, the vision of such devices, composed of non-toxic, earth-abundant, readily easily processed materials replacing/supplementing current-generation inorganic solar cells may become a reality. Organic cells offer potentially low-cost, roll-to-roll manufacturable, and durable solar power for diverse in-door and out-door applications. Importantly, further gains in efficiency and durability, to that competitive with inorganic PVs, will require fundamental, understanding-based advances in transparent electrode and interfacial materials science and engineering. This team-science research effort brought together an experienced and highly collaborative interdisciplinary group with expertise in hard and soft matter materials chemistry, materials electronic structure theory, solar cell fabrication and characterization, microstructure characterization, and low temperature materials processing. We addressed in unconventional ways critical electrode-interfacial issues underlying OPV performance -- controlling band offsets between transparent electrodes and organic active-materials, addressing current loss/leakage phenomena at interfaces, and new techniques in cost-effective low temperature and large area cell fabrication. The research foci were: 1) Theory-guided design and synthesis of advanced crystalline and amorphous transparent conducting oxide (TCO) layers which test our basic understanding of TCO structure-transport property relationships, and have high conductivity, transparency, and tunable work functions but without (or minimizing) the dependence on indium. 2) Development of theory-based understanding of optimum configurations for the interfaces between oxide electrodes/interfacial layers and OPV active layer organic molecules/polymers. 3) Exploration and perfection of new processing strategies and cell architectures for the next-generation, large-area flexible OPVs. The goal has been to develop for the solar energy community the fundamental scientific understanding needed to design, fabricate, prototype, and ultimately test high-efficiency cells incorporating these new concepts. We achieved success in all of these directions.

14 SOLAR ENERGY↗

Effects of processing conditions on flash sintering of commercial ZrN

Flash sintering (FS) is a potentially rapid and low-cost manufacturing technique for advanced ceramics. There are still many unknowns about ceramic FS, especially for highly conductive high-temperature ceramics (HTC), which often display decreased bulk conductivity with increasing temperature. This study qualitatively characterizes the flash behavior of highly conductive HTC materials using zirconium nitride (ZrN) as an example. The effects of processing parameters (e.g., DC voltage/electrical field strength, voltage ramp rate, post-flash holding time, mechanical pressure, sample milling, and choice of electrode materials) on ZrN flash behavior are also qualitatively studied and linked to samples microstructure and hardness. It is observed that best densification was achieved using 5 min Spex-milled ZrN powder under 25 MPa of applied pressure and constant 8 V DC. The potential mechanism for ZrN FS and the similarity and difference from FS of conventional oxides like YSZ have been proposed based on experimental observations, and the directions for future research are also pointed out.

Flash Sintering↗

Distinct Melt Infusion Architectures of Antiperovskite Solid Electrolytes

Antiperovskite solid electrolytes are an emerging class of lithium‐ion conductors distinguished by their unusually low melting points, enabling scalable, low‐temperature processing routes not accessible to most solid electrolytes. In this work, we synthesize phase‐pure chloride (Cl), bromide (Br), and mixed halide (ClBr) variants of antiperovskites and investigate their ionic conductivities in both powder and hot‐pressed forms. Hot pressing significantly enhances conductivity across all compositions, while energy‐dispersive X‐ray spectroscopy (EDS) of the mixed halide system reveals halide surface migration during densification. We further investigate the melt‐infiltration behavior of these electrolytes into substrates relevant to solid‐state battery architectures, including Al and Cu current collectors, conventional NMC and LFP cathodes, and a foamed NMC cathode with a highly porous architecture. The foamed cathode enables deep and uniform electrolyte penetration, highlighting the role of electrode architecture in facilitating melt infiltration. Across all substrates, electrolyte halide chemistry strongly influences wetting behavior, penetration depth, and resulting microstructural morphology. Together, these results establish clear processing–structure relationships for melt‐infiltrated antiperovskite solid electrolytes and demonstrate how electrolyte chemistry and electrode architecture govern interfacial morphology during integration, providing practical guidelines for processing and structural design in solid‐state battery systems.

antiperovskite↗

Microstructural Evolution Of Iron Oxyfluoride/Carbon Nanocomposites Upon Electrochemical Cycling

High electrochemical performance iron oxyfluoride conversion electrode undergoes complex electrochemical reaction mechanisms upon cycling. In this work, a combination of selected area electron diffraction (SAED) and scanning transmission electron microscopy/electron energy loss spectroscopy (STEM/EELS) analysis techniques have been used to understand the conversion-reconversion mechanisms of FeO 0.7 F 1.3 /C upon cycling. Considerable changes have been observed with cycling. For the fully delithiated electrodes, the nanometer scale intermixing of amorphous rutile and nanocrystalline rocksalt phases is stable up to 20 cycles; however, upon further cycling the amount of amorphous rutile phase decreased and amount of rocksalt phase increased gradually, implying incomplete reconversion reactions with increasing cycle number. In addition, a progressive growth of solid electrolyte interphase (SEI) layer was observed with cycling, which is mainly composed of LiF. Interestingly, Fe 2+ and Fe nanoparticles were found trapped in the SEI layer with increasing cycle number. Upon cycling, the combined progressive increase in Fe 2+ content and insulating LiF (from SEI and conversion product) give rise to the observed capacity loss.

25 ENERGY STORAGE↗

Disintegration of Meatball Electrodes for LiNi x Mn y Co z O 2 Cathode Materials

Mechanical degradation of Li-ion batteries caused by the repetitive swelling and shrinking of electrodes upon electrochemical cycles is now well recognized. Structural disintegration of the state-of-art cathode materials of a hierarchical structure is relatively less studied. In this paper, we track the microstructural evolution of different marked regimes in LiNi x Mn y Co z O 2 (NMC) electrodes after lithiation cycles. Decohesion of primary particles constitutes the major mechanical degradation in the NMC materials, which results in the loss of connectivity of the conductive network and impedance increase. We find that the structural disintegration is largely dependent on the charging rate – slow charging causes more damage, and is relatively insensitive to the cyclic voltage window. We use finite element modeling to study the evolution of Li concentration and stresses in a NMC secondary particle and employ the cohesive zone model to simulate the interfacial fracture between primary particles. Finally, we reveal that microcracks accumulate and propagate during the cyclic lithiation and delithiation at a slow charging rate.

25 ENERGY STORAGE↗

ESM of ionic and electrochemical phenomena on the nanoscale

Operation of energy storage and conversion devices is ultimately controlled by series of intertwined ionic and electronic transport processes and electrochemical reactions at surfaces and interfaces, strongly mediated by strain and mechanical processes. In a typical fuel cell, these include chemical species transport in porous cathode and anode materials, gas-solid electrochemical reactions at grains and triple-phase boundaries (TPBs), ionic and electronic flows in multicomponent electrodes, and chemical and electronic potential drops at internal interfaces in electrodes and electrolytes. Furthermore, all these phenomena are sensitively affected by the microstructure of materials from device level to the atomic scales. Similar spectrum of length scales and phenomena underpin operation of other energy systems including primary and secondary batteries, as well as hybrid systems such flow and metal-air/water batteries.

36 MATERIALS SCIENCE↗

Gas-mediated defect engineering in earth-abundant Mn-rich layered oxides for non-aqueous sodium-based batteries

Gases are often by-products of battery materials during cell formation and degradation, affecting the cycle life and safety of rechargeable batteries. However, understanding gas-mediated (electro)-chemical reactions and nanoscale structural transformations during the synthesis of battery electrode materials remains challenging because of the lack of suitable characterization routes and the complexity of the interplay between thermodynamics and kinetics. Here, in this study, we use operando synchrotron X-ray diffraction, in situ transmission X-ray microscopy and multiscale modelling to elucidate the reaction pathways and microstructural defect development of earth-abundant Mn-rich layered oxides as positive electrode materials for sodium-based batteries. In particular, we demonstrate the dominant role of CO 2 over O 2 and H 2 O (g) in modulating the competition between entropy and enthalpy during solid-state synthesis. Using Ni 0.25 Mn 0.75 CO 3 as a model precursor, we reveal that CO 2 generation favours the formation of entropy-driven metastable intermediates, suppresses closed pore/nanovoids formation and decreases chemical heterogeneity and residual lattice strain of Mn-rich layered oxides during the synthesis. This result motivates a fast-sintering strategy to promote CO 2 release, which ultimately leads to improved chemo-mechanical and electrochemical stability of the Mn-rich positive electrodes when tested in non-aqueous Na metal coin cells.

36 MATERIALS SCIENCE↗

Multimodal Nanoscale Tomographic Imaging for Battery Electrodes

Accurate representations of the 3D structure within a lithium-ion battery are key to understanding performance limitations. However, obtaining exact reconstructions of electrodes, where the active particles, the carbon black and polymeric binder domain, and the pore space are visualized is challenging. In this work, it is shown that multimodal imaging can be used to overcome this challenge. High-resolution ptychographic X-ray computed tomography are combined with lower resolution but higher contrast transmission X-ray tomographic microscopy to obtain 3D reconstructions of pristine and cycled graphite-silicon composite electrodes. This cross-correlation enables quantitative analysis of the surface of active particles, including the heterogeneity of carbon-black and binder domain and solid-electrolyte interphase coverage. Capturing the active particles as well as the carbon black-binder domain allows using these segmented structures for electrochemical simulations to highlight the influence of the particle embedding on local state of charge heterogeneities.

25 ENERGY STORAGE↗

Random Walk Analysis of the Effect of Mechanical Degradation on All-Solid-State Battery Power

Mechanical and electrochemical phenomena are coupled in defining the battery reliability, particularly for solid-state batteries. Micro-cracks act as barriers to Li-ion diffusion in the electrolyte, increasing the average electrode’s tortuosity. In our previous work, we showed that solid electrolytes are likely to suffer from mechanical degradation if their fracture energy is lower than 4 J m -2 [G. Bucci, T. Swamy, Y.-M. Chiang, and W. C. Carter, J. Mater. Chem. A (2017)]. Here we study the effect of electrolyte micro-cracking on the effective conductivity of composite electrodes. Via random analyzes, we predict the average diffusivity of lithium in a solid-state electrode to decrease linearly with the extension of mechanical degradation. Furthermore, the statistical distribution of first passage times indicates that the microstructure becomes more and more heterogeneous as damage progresses. In addition to power and capacity loss, a non-uniform increase of the electrode tortuosity can lead to heterogeneous lithiation and further stress localization. Finally, the understanding of these phenomena at the mesoscale is essential to the implementation of safe high-energy solid-state batteries.

25 ENERGY STORAGE↗

Synchrotron Imaging of Pore Formation in Li Metal Solid-State Batteries Aided by Machine Learning

High-rate capable, reversible lithium metal anodes are necessary for next generation energy storage systems. In situ tomography of Li/LLZO/Li cells is carried out to track morphological transformations in Li metal electrodes. Machine learning enables tracking the lithium metal morphology during galvanostatic cycling. Nonuniform lithium electrode kinetics are observed at both electrodes during cycling. Hot spots in lithium metal are correlated with microstructural anisotropy in LLZO. Mesoscale modeling reveals that regions with lower effective properties (transport and mechanical) are nuclei for failure. Advanced visualization combined with electrochemistry represents an important pathway toward resolving non-equilibrium effects that limit rate capabilities of solid-state batteries.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Fundamental Investigations and Rational Design of Durable High-Performance SOFC Cathodes

The main objective of this project is to unravel the degradation mechanism of LSCF cathodes under realistic operating conditions with different types of contaminants, aiming towards the rational design of cathodes with high-performance and enhanced durability by combining a porous backbone (such as LSCF) with a thin catalyst coating. The mechanistic understanding will help us to optimize the composition and morphology of the catalyst layer and microstructure of the LSCF backbone for better performance and durability. More specifically, the technical objectives include: (1) to unravel the degradation mechanism of LSCF cathodes under realistic operating conditions with different types of contaminants using in situ and ex situ measurements performed on specially-designed cathodes; (2) to examine the microstructural and compositional evolution of LSCF cathodes as well as the cathode/electrolyte interfaces under realistic operating conditions; (3) to correlate the fuel cell performance instability and degradation with the microstructural and morphological evolution and surface chemistry change of the cathode under realistic operating conditions; (4) to explore new catalyst materials and electrode structures to enhance the stability of the LSCF cathode under realistic operating conditions; and (5) to validate the long term stability of the modified LSCF cathode in commercially available cells under realistic operating conditions. We have systematically evaluated LSCF cathodes in symmetrical cells and anode supported cells under realistic conditions with different types of contaminants such as humidity, CO 2 , and Cr. Electrochemical models for the design of test cells and understanding of mechanisms have been developed for the exploration of fundamental properties of electrode materials. It is demonstrated that the activity and stability of LSCF cathodes can be degraded by the introduction of contaminants. The microstructural and compositional evolution of LSCF cathodes as well as the cathode/electrolyte interfaces under realistic operating conditions has been studied. It is found that SrO readily segregated/enriched on the LSCF surface. More severe contamination conditions cause more SrO on surface. Novel catalyst coatings through particle depositions (PrOx) or continuous thin films (PNM) were successfully developed to improve the activity and stability of LSCF cathodes. Finally, we have demonstrated enhanced activity and stability of LSCF cathodes over longer periods of time in homemade and commercially available cells by an optimized PNM (dense film and particles) infiltration process, under clean air and realistic operating conditions (3% H 2 O, 5% CO 2 and direct Crofer contact). Both performance and durability of single cells with PNM coating has been enhanced compared with those without coating. Raman analysis of cathodes surface indicated that the intensity of SrCrO 4 was significantly decreased.

30 DIRECT ENERGY CONVERSION↗

Advanced Materials Characterization and Processing of Gen II Materials Based Lithium Ion Battery

The purpose of this Cooperative Research and Development Agreement (CRADA) between Oak Ridge National Laboratory (ORNL) and Dow Kokam, LLC was to investigate the microstructure and materials processing on long-term performance of Dow Kokam’s Gen II anodes and cathodes for lithium ion batteries. The findings were implemented into Dow Kokam’s new U.S. based production line, which has a capacity of 600 MWh/yr in total battery output. A principal need for automotive energy storage applications is the ability of the battery pack to satisfy a 10-15 year calendar life in addition to improved safety, high charge-discharge rate capability, high energy density, and high power density. Current cathode chemistries such as those based on LiNixMnyCo1-x-yO2 (NMC) metal oxides are limited to approximately 1500 cycles (or 5-7 year equivalent automotive calendar life). Dow Kokam Gen II technology has shown a 2× cycle life over conventional NMC based materials, while also improving by similar metrics the charge-discharge limits. The impact of this improvement is significant in terms of launching pure electric vehicles and plug-in hybrid electric vehicles with lifetimes comparable to those of the traditional IC engine. However, in order to scale the technology and achieve substantial market penetration, the electrode structure and processing based on the new Gen II material in comparison to that of the traditional NMC needs to be better understood. As the microstructure and chemistry of the new electrode type have been elucidated by this project, scaling and mass production has become the focus. Electrode dispersion formulations, coating parameters, and methods of energy savings were subsequently investigated. The capabilities of ORNL were implemented to assist in these efforts in terms of quality control, materials characterization, and electrochemical testing. Dow Kokam provided raw materials and electrodes, as well as background IP and technical expertise. The current state-of-the-art for NMC cathode durability is 1500 cycles to 100% depth of discharge (DOD) at 1C/-1C charge/discharge rates. This cycle lifetime only satisfies about half of the lifetime requirement for plug-in hybrid electric vehicles (PHEVs) and electric vehicles (EVs). Dow Kokam’s Gen II modified NMC cathode increases cycle life by 2×, depending on the charge/discharge rates, and will be capable of meeting the full 15 year lifetime once scaled to mass production. This improvement will allow PHEV and EV manufacturers to use only one battery pack per vehicle and will result in approximately 50% reduction in energy required to produce battery packs on a per vehicle basis. This further translates into a significantly reduced cost of ownership for PHEVs and EVs based on lithium ion battery technology. However, the chemical and microstructural changes of the modified Gen II anodes and cathodes during long-term operation are not well understood, as well as the effects of the starting material modifications to anode and cathode active material performance (i.e., nanoscale coatings deposited on the surfaces of graphite and NMC). Effects of processing variables related to mixing and coating of the electrode materials on cell performance and durability were also studied. To supplement these materials characterization and processing variable experiments, thorough electrochemical testing was completed by Dow Kokam.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Modeling Oxygen Partial Pressure in Solid Oxide Electrolysis Cells: The Microstructure Effect

Oxygen partial pressure is an important thermodynamic state variable that affects both the performance and degradation of solid oxide electrolysis cells. In this work, a 3D model developed from Virkar’s 1D model has been applied to reconstructed and synthetic microstructures of Ni-YSZ-GDC-LSCF cell. The effect of the microstructures, including the thickness of the YSZ and GDC layer, and the compositions of the hydrogen and oxygen electrode, on the distribution of oxygen partial pressure has been investigated. The results show that the maximum oxygen partial pressure may occur on the interface between oxygen electrode and GDC layer or between GDC layer and YSZ layer depending on the rate of oxygen ion exchange between GDC and YSZ. A thicker GDC layer lowers the maximum oxygen partial pressure in the cell, while a thicker YSZ layer lowers the maximum oxygen partial pressure in the hydrogen electrode. In addition, the Ni:YSZ ratio and porosity also affects the maximum partial pressure. These findings provide insights on mitigating degradation in solid oxide electrolysis cell by tuning the microstructures.

Lei, Yinkai↗

Determining Electrode Tortuosity and Rate Limitations from Experiments and Modeling

CAE models efficiently address 3D large battery performance and safety design. Further work is needed to increase electrochemical model fidelity, reduce expense of parameter ID, and integrate degradation mechanisms, enabling optimization of designs for lifetime. Microstructure models provide deeper insight into predict effective properties of macro-homogeneous models and heterogeneous utilization of electrode degradation. Enabling 10-minute fast charge of BEV200+ requires electrolytes with enhanced transport and low electrode tortuosity.

30 DIRECT ENERGY CONVERSION↗

Utilizing Oxygen Redox in Layered Cathode Materials from Multiscale Perspective

We report in high-capacity layered oxide cathode materials, utilization of lattice oxygen as a redox center is considered to be one of the most promising approaches to overcome the capacity limitation set by conventional transition metal redox centers. However, rapid material degradation is often associated with oxygen oxidation, leading to formidable challenges in utilizing oxygen redox. Further mechanistic understanding of the oxygen activities thus becomes critical to better control oxygen redox reactions. This review summarizes recent advances for investigating oxygen redox reactions in cathode materials from a multiscale perspective, i.e., from the atomistic level to the microstructure regime. First the mechanistic aspects of oxygen redox and the consequences of this reaction on various electrode degradation pathways during battery operation (e.g., oxygen loss, transition metal migration, irreversible phase transition), relating structural changes at the crystallographic scale to those at the macro scale, are discussed. Then recent developments based on atomic and microstructure modifications that are promising for improving the reversibility of oxygen redox reaction or mitigating the harmful processes arising from oxidation of the oxygen centers under high operating voltage are recounted. The analysis is concluded with a commentary on further research directions toward optimizing the oxygen activity for high-capacity charge storage.

25 ENERGY STORAGE↗