Search NASA⌕ Search

SEARCH · Search NASA

Results for “electron backscattered diffraction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

Impact of Molten Gallium on the Microstructure and Corrosion Behavior of Aluminum and Uranium-Aluminum Alloys for Used Nuclear Fuel Reprocessing

Test reactors around the world utilize highly enriched uranium fuel to achieve high neutron fluxes for materials testing. Once spent, the remaining uranium is a valuable resource for subsequent fuel fabrication. However, some of these test reactor cores consist of curved plate-type fuel elements, fabricated using aluminum alloy 6061 (AA6061) cladding to encapsulate a uranium-aluminum alloy (UAlx) fuel matrix. These assemblies require non-standard reprocessing approaches for uranium recovery, as aluminum dissolves readily in acidic solutions, generating large volumes of waste and complicating downstream chemical separations. In this work, we investigate a novel chemical decladding strategy based on the interaction between AA6061/UAlx and molten gallium (Ga). Ga is known to induce severe degradation of aluminum metal through liquid metal embrittlement (LME), even at relatively low Ga concentrations. By penetrating the aluminum crystal lattice, Ga disrupts grain cohesion and facilitates fracture or dissolution of the aluminum matrix. Thermodynamic analysis of the Al–Ga binary phase diagram suggests that Ga may offer a viable pathway to selectively weaken or dissolve the AA6061 cladding, and potentially the aluminum component of the UAlx fuel matrix within. To this end, parametric experiments were performed at 50 °C and 100 °C across a range of Al–Ga atomic fractions. At lower Al fractions, the AA6061 was completely molten after 2 hours of exposure to the Ga metal. In contrast, samples with higher Al fractions (0.9 Al, 0.1 Ga) contained residual solids after 2 hours, which were characterized by microstructural examination using electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM). These Al-Ga compositions were also evaluated using FactSage thermodynamic modeling to further elucidate the relationship between phase diagram behavior and LME.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Mitigation of tin whisker growth by inserting Ni nanocones

Highlights: • Tin whisker growth is mitigated effectively by inserting Ni nanocones. • Ni nanocones impede Sn dynamic recrystallization by blocking dislocation motions. • The inhibition method and mechanism are important to the study of tin whisker. - Abstract: An innovative controllable way has been proposed to mitigate tin whisker growth by inserting Ni nanocones prepared by electrodeposition. The results reveal that, after inserting Ni nanocones, tin whisker formation is mitigated effectively for 1.6 μm Sn coating but there is no inhibition effect for 4.5 μm Sn coating. The coatings are characterized by X-ray diffraction, scanning electron microscopy, energy dispersive spectrometer and electron backscatter diffraction (EBSD). The EBSD results show that Sn grain size without Ni nanocones increases significantly after indentation test compared with Sn grains with Ni nanocones. The inhibition effect of Ni nanocones on whisker growth can be ascribed to its specific structure which prevents dynamic recrystallization and produces horizontal grain boundaries of Sn grains. The structural inhibition method and mechanism proposed are of great importance to the research of tin whisker.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Correlation of critical current density to quasi-biaxial texture and grain boundary cleanliness in fully dense Bi-2212 wires

The distinctive quasi-biaxial texture of Bi 2 Sr 2 CaCu 2 O x (Bi-2212) plays an important role in enabling high critical current density ($J_c$) in Bi-2212 round wires (RWs). Here we studied three over pressure heat treated wires with $J_c$ varying by a factor of ~10, all being fully dense. Using electron backscatter diffraction, we observed the differences in biaxial texture in these three wires. Transmission electron microscopy also revealed differences in grain boundary (GB) cleanliness and connectivity. These analyses showed that high $J_c$ is unambiguously correlated to the best biaxial texture, which is in turn correlated to slow cooling from the liquid melt into solid Bi-2212. However, at 4.2 K, there is a negligible difference in intragrain pinning in the three wires, suggesting that the $J_c$ variation by a factor of ~10 is primarily due to variable filament and intergrain connectivity. In this work, the principal determinants of intergrain connectivity is the quasi-biaxial texture and GB cleanliness. Overall, $J_c$ optimization of the Bi-2212 RW is a complex multi-variable process, but this study shows that maximizing the biaxial texture quality is an important first step in such an optimization process.

36 MATERIALS SCIENCE↗

Microstructural characterization of transformable Fe-Mn alloys at different length scales

The as-annealed and deformed Microstructure of transformable Fe-Mn alloys were, comprehensively, characterized over a wide range of length scales. Differential interference contrast optical metallography, combined with a tinting etching method, was employed to examine the grain morphology. A new specimen preparation method, involving electro-polishing and electro-etching, was developed for scanning electron microscopy and electron back-scattered diffraction analysis. This method leads to a very good imaging contrast and thus bridges the length scale gap between optical metallography and transmission electron microscopy. Moreover, it enables simultaneous scanning electron microscopy and electron backscatter diffraction analysis which allows correlations among morphology, crystal orientation and phase analysis in the length scale of microns. Transmission electron microscopy investigations were also made to evaluate the thermal and mechanical transformation products as well as defect structures.

36 MATERIALS SCIENCE↗

Differences in Oxidation Behavior of Conventionally Cast and Additively Manufactured Co-Base Alloy MAR-M-509

High-temperature oxidation behavior of conventionally cast and additively manufactured (AM) Co-base alloy MAR-M-509 was compared in the present study. The specimens were exposed in air at 1000 °C and characterized by means of scanning electron microscopy equipped with energy/wavelength dispersive x-ray spectroscopy (EDX/WDX) and electron backscatter diffraction as well as transmission electron microscopy. Substantial differences in the oxidation processes of two alloy versions were observed. Faster oxidation of the cast alloy was mainly induced by (1) oxidation of coarse primary carbides, (2) internal oxidation and nitridation processes and (3) incorporation of other alloy constituents (e.g., Co, Ni, W) into the Cr-oxide scale. AM specimens, in contrast, formed a more homogeneous, thinner and better adherent external oxide scale. The results are discussed in terms of differences in the chemical composition and alloy microstructure, including the grain size distribution in the material and the morphology of the strengthening precipitate phases.

36 MATERIALS SCIENCE↗

Mechanism of Texture and Precipitates Evolution in CGO Silicon Steel During High-Temperature Annealing Process

Grain-oriented silicon steel is an important soft magnetic material for electrical applications. A conventional grain-oriented silicon steel with final thicknesses of 0.27, 0.23 and 0.20 mm was prepared separately by a two-stage cold rolling process. Texture evolution, precipitates distribution and Goss textures formed during secondary recrystallization were analyzed by electron backscattered diffraction and field emission scanning electron microscopy. The results show that plate thickness influences the distribution density of secondary phase particles and the content of favorable texture components such as {111} <112>, {111} <110> and {112} <110> texture. Decreasing plate thickness increases the areal density of secondary phase particles, the temperature of secondary recrystallization, which also increases the content of favorable texture component, and the strength of Goss texture in secondary recrystallization. Goss grains have higher particle density than the grains with other orientations, which facilitates their abnormal growth by swallowing surrounding grains with lower particle density.

36 MATERIALS SCIENCE↗

Deformation Mechanism Transition in Additively Manufactured Compositionally Graded Fe-Base Alloys

Microstructure-dependent deformation and fracture behavior was investigated for an additively manufactured compositionally graded alloy (CGA) printed using the laser-directed energy deposition (L-DED) method to explore an alternative approach for dissimilar metal joints in nuclear energy systems. The electron backscatter diffraction (EBSD) maps from scanning electron microscopy (SEM) display a clear microstructural transition with decreasing austenite-forming elements (Ni and Mn), from an austenite (γ) dominant structure, to a complex composite structure containing ferrite (α), martensite (α') and retained austenite, and then to a fully ferritic structure. EBSD data were recorded in situ during tensile testing in SEM, and the evolution of the deformation mechanism and microstructure was characterized using Kikuchi diffraction pattern analysis. Complementary analysis for high-resolution features was also performed using scanning transmission electron microscopy (STEM). The Ni/Mn-rich austenite-dominant microstructures showed a complex deformation mechanism of two-step martensitic transformation (γ→ε→α'), whereas the minor austenite phase retained in the ferrite and/or martensite matrix showed a single transformation route (γ→α'). Ordinary dislocation glide and twinning via partial dislocation glide were observed in the austenite deformation. Meanwhile, the ferrite and martensite grains deformed mainly by ordinary dislocation slips and grain rotation. Furthermore, static tensile fracture was also highly dependent on local composition and phase constituents.

36 MATERIALS SCIENCE↗

Anisotropic deformation of extruded magnesium alloy AZ31 under uniaxial compression: A study with simultaneous in situ synchrotron x-ray imaging and diffraction

In situ synchrotron x-ray imaging and diffraction are used to investigate anisotropic deformation of an extruded magnesium alloy AZ31 under uniaxial compression along two different directions, with the loading axis (LA) either parallel or perpendicular to the extrusion direction (ED), referred to as LA∥ED and LAED, respectively. Multiscale measurements including stress–strain curves (macroscale), x-ray digital image correlation (mesoscale), and diffraction (microscale) are obtained simultaneously. Electron backscatter diffraction is performed on samples collected at various strains to characterize deformation twins. The rapid increase in strain hardening rate for the LA∥ED loading is attributed to marked {101¯2} extension twinning and subsequent homogenization of deformation, while dislocation motion leads to inhomogeneous deformation and a decrease in strain hardening rate.

36 MATERIALS SCIENCE↗

Corrosion-induced microstructural developments in 316 stainless steel during exposure to molten Li 2 BeF 4 (FLiBe) salt

The microstructural evaluation and characterization of 316 stainless steel samples that were tested in molten Li 2 BeF 4 (FLiBe) salt were investigated in this study for evaluating its performance in high-temperature molten fluoride salts. Recently, 316 stainless steel and FLiBe salt are being actively considered as the main structural alloy and primary coolant of fluoride salt-cooled high-temperature reactor (FHR), a leading nuclear reactor concept for the next generation nuclear plants (NGNP). In support of the materials development for the FHR, high-temperature corrosion tests of 316 stainless steel in molten FLiBe salt at 700°C have been conducted in both bare graphite crucibles and 316 stainless steel-lined crucibles in an inert atmosphere for up to 3000 hours. The microstructure of the tested samples was comprehensively characterized using scanning electron microscopy (SEM) in conjunction with energy dispersive x-ray spectroscopy (EDS) and electron backscatter diffraction (EBSD), and scanning transmission electron microscopy (STEM) with EDS. In addition to the noticeable intergranular corrosion attack on surface, the corrosion in terms of the Cr depletion along high angle grain boundaries (15-180º) extended to 22µm in depth after 3000-hour exposure to molten FLiBe salt in graphite crucible. The coherent Σ3 grain boundary appeared high resistance to the Cr depletion. The substantial Cr depletion from the near-to-surface layer induced phase transformation from γ-martensite to α-ferrite phase (FeNi x ) during corrosion at 700ºC. Furthermore, the presence of graphite in the molten salt doubled the corrosion attack depth and led to the formation of round Mo2C, hexagonal Cr 7 C 3 and needle-like Al 4 C 3 phase within the alloy as deep as 50 µm after 3000-hour corrosion testing. Based on the microstructural analysis, the corrosion mechanisms of 316 stainless steel in molten FLiBe salt in different corrosion crucibles were illuminated through schematic diagrams. Additionally, a thermal diffusion controlled corrosion model was developed and validated by experimental data for predicting the long-term corrosion attack depth.

36 MATERIALS SCIENCE↗

Correlative characterization of primary Al{sub 3}(Sc,Zr) phase in an Al–Zn–Mg based alloy

Three-dimensional electron backscatter diffraction, focused ion beam, transmission electron microscopy and energy filtered transmission electron microscopy were employed to investigate the structural information of primary Al{sub 3}(Sc,Zr) phase, i.e. size, shape, element distribution and orientation relationship with the α-Al matrix. It was found that (i) most primary Al{sub 3}(Sc,Zr) phases have a cubic three-dimensional morphology, with a size of about 6–10 μm, (ii) most primary Al{sub 3}(Sc,Zr) phases are located within the α-Al matrix, and exhibit a cube to cube orientation relationship with the α-Al matrix, and (iii) a layer by layer growth was observed within primary Al{sub 3}(Sc,Zr) phases. Al, Cu, Si and Fe are enriched in the α-Al matrix between the layers of cellular eutectic Al{sub 3}(Sc,Zr) phase, while Sc, Ti and Zr are enriched in small Al{sub 3}(Sc,Zr) phases. A peritectic reaction and subsequent eutectic reaction between Al{sub 3}Sc and Al was proposed to interpret the observed layer by layer growth. This paper demonstrates that the presence of impurities (Fe, Si, Cu, Ti) in the diffusion field surrounding the growing Al{sub 3}(Sc,Zr) particle enhances the heterogeneous nucleation of Al{sub 3}(Sc,Zr) phases. - Highlights: • Most fine cubic primary Al{sub 3}(Sc,Zr) phases were observed within the α-Al matrix. • A layer by layer growth within primary Al{sub 3}(Sc,Zr) phase was observed. • A peritectic and subsequent eutectic reaction between Al{sub 3}Sc and Al was proposed. • Impurities in diffusion fields enhance heterogeneous nucleation of Al{sub 3}(Sc,Zr)

36 MATERIALS SCIENCE↗

NEUTRON-IRRADIATION–INDUCED DAMAGE ASSESSMENT IN CONCRETE USING COMBINED PHASE CHARACTERIZATION AND NONLINEAR FAST FOURIER TRANSFORM SIMULATION

Understanding irradiation effects in concrete cavities of light water reactors is critical to the long-term operation (60+ years) of US nuclear power plants. Susceptibility of concrete to neutron irradiation greatly varies as a function of its constituents: coarse aggregates, sand, and hardened cement paste (hcp). In particular, higher irradiation–susceptibility of aggregates was found to be a direct function of radiation-induced volumetric expansion (RIVE), or the propensity of aggregates to swell as a function of mineral contents, structures and textures. Irradiation-induced amorphization is accompanied by significant swelling, especially in silicates. For example, the maximum volumetric expansions of quartz and feldspars have been shown to be as large as ≈ 18% and ≈ 8%, respectively, while the change of density in calcite remains rather low (≈ 0.3–0.5%). High swelling is associated with a high number of covalent bonds (Si–O) and a high degree of polymerization of [SiO4] tetrahedrons. Differential RIVEs between rock-forming minerals cause high stresses and may potentially develop cracking within the aggregates at the interface between aggregates and the hcp and within the hcp. Modeling neutron-irradiation effects in concrete requires addressing the problem at a scale that captures both the details of the aggregates’ mineralogy and texture, which is <~ 100 μm, and the representative size of concrete, which is ~ 10 cm. This requires high-resolution, large mapping capabilities. To this end, the US Department of Energy (DOE) Light Water Reactor Sustainability (LWRS) Program developed an original tool suite called Microstructure Oriented Scientific Analysis of Irradiated Concrete (MOSAIC) in which Nonlinear 2D-fast Fourier transform (FFT) techniques are employed to model mechanical or irradiation-induced cracking of high-resolution complex microstructures derived from combined mapping techniques, including micro x-ray fluorescence (m-XRF), energy-dispersive x-ray spectroscopy (EDS), electron backscatter diffraction (EBSD), ellipsometry, and scanning electron microscopy (SEM). Irradiated mineral properties are derived from the Irradiated Minerals, Aggregate and Concrete (IMAC) database, which includes available relevant literature data. Rigorous coupled damage-creep simulations are obtained through sequential linear analysis. Illustrations of actual accelerated irradiation-damage propagation in a complex microstructures are presented herein.

Le Pape, Yann↗

Enhanced stress durability of nano resonators with scandium doped electrodes

To explore mechanical stress durability of thin aluminum-scandium (AlSc) films, 0.86 GHz nano resonators with AlSc electrodes have been manufactured. Four different samples have been prepared altering the Sc content in the alloy between 0.0% and 2.5%. A final lift-off step accomplished manufacture procedure of the devices. The resonators have been operated with heavy load to determine power durability. The resonators with AlSc electrodes show increased power durability compared to conventional Al metallized devices. Texture and grain structure of all films have been investigated by means of electron backscatter diffraction (EBSD) and atomic force microscopy (AFM). Material fatigue of electrodes has been visualized by scanning electron microscopy (SEM). The refined grain structure of these alloys can explain the enhanced mechanical stress durability of AlSc electrodes. - Research Highlights: {yields}Enhanced power durability of SAW devices with Sc doped electrodes. {yields}Refined grain structure of Sc doped Al films. {yields}Sudden device breakdown of highly Sc doped devices.

36 MATERIALS SCIENCE↗

Indentation size effect in tungsten: Quantification of geometrically necessary dislocations underneath the indentations using HR-EBSD

Highlights: • Revealed the dislocation structure below nanoindentations via ECCI and HR-EBSD. • Experimentally quantification of GND densities, with higher GND densities at lower depths. • Qualitative validation of the Nix-Gao model on the indentation size effect. - Abstract: During indentation testing of the low defect density crystalline materials, higher hardness values are found at lower indentation depths, which is referred to as an indentation size effect. The depth-dependence of hardness can be described by the Nix-Gao model, which is based on the concept of Geometrically Necessary Dislocations (GNDs). The underlying dislocation mechanism remains, however, unclear and requires independent measurement of GND density below the indentation. In the present work, the depth-dependency of the GND density is quantified underneath the Berkovich indentations in tungsten via high-resolution electron backscatter diffraction. There a higher GND density is found for lower indentation depths, resulting in a higher Taylor hardness for measured GND density.

36 MATERIALS SCIENCE↗

Microstructural evolution and mechanical properties on an ARB processed IF steel studied by X-ray diffraction and EBSD

Accumulative Roll Bonding (ARB) is one of the so-called severe plastic deformation (SPD) processes, allowing the production of metals and alloys with ultrafine (micro-nano) structures. Materials with ultrafine grains present attractive properties like the simultaneous increase in strength and ductility. Our interest in these materials is focused on their microstructural evolution during ARB processing, eventually responsible for the enhancement of those mechanical properties. In the current work we follow the evolution of the microstructure in an interstitial-free (IF) steel deformed by ARB after consecutive processing cycles, by means of Electron BackScatter Diffraction (EBSD) and X-ray diffraction (XRD). Particularly, we present results related to texture, grain (GS) and domain sizes, grain boundary character, density of Geometrically Necessary Dislocations (GND), Grain Orientation Spread (GOS), lattice parameters, microstrain, dislocation density and their spatial arrangement. After 5 ARB cycles the system shows a microstructure constituted mainly by submicrometric grains with high angle boundaries and low presence of dislocations inside the grains. - Highlights: •The evolution of microstructure is followed simultaneously by using GAM, GOS and GND (EBSD) and XRD. •LAGBs and subgrains disappear after few cycles SSDs and HAGBs persist at the end. •Dynamic recrystallization counterbalances dislocation arrays and diminishes hardening rate. •Grain size stabilization is revealed as a mechanism for increasing ductility after few ARB cycles.

36 MATERIALS SCIENCE↗

Microstructural Investigations in Metals Using Atom Probe Tomography with a Novel Specimen-Electrode Geometry

In this work, a new atom probe design is presented along with data showing spectral performance and selected microstructural characterization examples. The instrument includes a curved reflectron, a 532-nm laser, and an integrated, fixed-position, counter electrode in a configuration with moderate electric field enhancement that includes improvements in ease of use and cost of ownership. Both voltage-pulsed and laser-pulsed performance is shown for a variety of materials including Al, Si, W, 316 stainless steel, Inconel 718, and GaN. Characterization of grain boundaries and phase boundaries, including correlation with transmission electron backscatter diffraction results in Inconel 718, is shown. Lastly, a detailed case study of the resultant microstructure between laser-beam and electron-beam additive manufacturing paths in Inconel 718 is also presented.

36 MATERIALS SCIENCE↗

Characterization of n-Type Iodine-Doped and Indium-Doped CdTe/Cd-Se-Te Thin Films Fabricated by Close-Spaced Sublimation Epitaxy

In this study, n-type CdTe thin films, specifically iodine-doped CdTe (CdTe:I), indium-doped CdTe (CdTe:In), and indium-doped Cd-Se-Te (CST:In), were synthesized using close-spaced sublimation epitaxy (CSSE). Characterization techniques secondary ion mass spectrometry (SIMS), electron backscatter diffraction (EBSD), Hall-effect measurements, and time-resolved photoluminescence (TRPL) were employed to analyze the chemical, structural, and electronic properties of these materials. The results indicated epitaxial single crystal CSSE films grew on the single crystal substrates, with carrier density ranging from 10^14 - 10^16 cm -3 , and after post-annealing, the minority-carrier lifetimes reach near the radiative limit. Additionally, a preliminary exploration of homojunction structures with an n- type (CdTe:In /CST:In /CdTe:I) /CdTe:P /Cu /Mo configuration was performed. The best device performance was achieved with CdTe:I including CdS aiding in band alignment, resulting in a power conversion efficiency (..eta..) of 2.61% with open circuit voltage (Voc) of 850 mV, fill factor (FF) of 47.8%, and short-circuit current (Jsc) of 6.44 mA/cm 2 . The observed low Jsc and efficiency may be attributed to a buried junction and a poor interface, due to dopant interdiffusion. Consequently, further investigations focusing on interface optimization, diffusion blocking, and reduced recombination through passivation, are crucial to enhancing the efficiency of CSSE CdTe homojunction devices in the future.

cadmium compounds↗

EBSD analysis of surface and bulk microstructure evolution during interrupted tensile testing of a Fe-19Cr-12Ni alloy

Highlights: • Similar deformation structures are obtained for surface and bulk grains. • A lower strain is needed for twinning in surface grains than in bulk grains. • A reduced ability to cross-slip due to low SFE leads to an increasing LAB density. • Twinning reduces the dislocation slip length. • High strain-hardening rate is maintained up to high strains. - Abstract: The microstructure evolution in both surface and bulk grains in a pure Fe-19Cr-12Ni alloy has been analyzed using electron backscatter diffraction after tensile testing interrupted at different strains. Surface grains were studied during in situ tensile testing performed in a scanning electron microscope, whereas bulk grains were studied after conventional tensile testing. The evolution of the deformation structure in surface and bulk grains displays a strong resemblance but the strain needed to obtain a similar deformation structure is lower in the case of surface grains. Both slip and twinning are observed to be important deformation mechanisms, whereas deformation-induced martensite formation is of minor importance. Since the stacking fault energy (SFE) is low, ~17 mJ/m{sup 2}, dynamic recovery by cross slip of un-dissociated dislocations is unfavorable. This reduces the annihilation of dislocations which in turn leads to a significant increase of low angle boundaries with increasing strain. The low SFE also favors formation of deformation twins which reduces the slip distance, leading to a hardening similar to the Hall-Petch relation. The combination of a low ability for cross-slip and a reduced slip distance caused by twinning is concluded to be the main reason for maintaining a high strain-hardening rate up to strains close to necking.

36 MATERIALS SCIENCE↗

Orientation imaging microscopy of polycrystalline sodium chloride

A novel preparation technique is described that makes possible grain size analysis of polycrystalline NaCl using orientation imaging microscopy via electron backscatter diffraction (EBSD). The preparation methodology is specifically developed to overcome difficulties in preparing microporous NaCl for microscopy. The grain size and crystallographic texture of polycrystalline NaCl samples, prepared via solution pressure and sintered in the range of 650-780 deg. C, were able to be measured successfully with EBSD. The limitations of the preparation technique for EBSD analysis of NaCl are also discussed.

36 MATERIALS SCIENCE↗