SEARCH · Search NASA

Results for “elevated temperature”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

All sources NASA NTRS DOE OSTI

NASA NTRS1976

Rates of reactions ClO + ClO yields Cl2 + O2 and ClO + O yields Cl + O2 at elevated temperatures

Results are reported for an experiment in which a shock tube was employed to measure the reaction rates of chlorine-oxygen systems at high temperatures. In this experiment, a mixture of chlorine and ozone, diluted by oxygen and argon, was heated by two consecutive shock waves (primary and reflected) to produce a temperature in the range from 1000 to 1400 K and a pressure of between 3.5 and 9 atm. The reflected shock thermally decomposed the ozone; the resulting atomic oxygen reacted with molecular chlorine to produce ClO; and the variation in ClO concentration after passage of the reflected shock was observed by monitoring the intensity of 2537-A radiation passing through the test gas. The rates of the two cited reactions are deduced from the variation pattern. The rate coefficient values are found to be compatible with existing data obtained in lower pressure and temperature ranges.

Park, C.↗

NASA NTRS1977

Tensile and creep rupture properties of (16) uncoated and (2) coated engineering alloys at elevated temperatures

Sixteen test materials were supplied by NASA-Lewis Research Center as wrought bar or cast remelt stock. The cast remelt stock was cast into test blanks with two such materials being also evaluated after Jocoat coating was applied. Mechanical properties evaluated included tensile, modulus of elasticity, Poisson's Ratio, creep properties and creep rupture strength. Tests were conducted at temperatures applicable to the service temperature of the various alloys. This range extended from room temperature to 1000 C.

Fritz, L. J.↗

NASA NTRS1977

Mechanical properties of several nickel alloys in hydrogen at elevated temperatures

Tests were performed to determine low cycle fatigue and crack growth rate properties of one iron-base and two forms of one cast nickel-base alloy. The alloys were tested in various forms and/or heat-treat conditions that are proposed for use in a high-pressure hydrogen or a hydrogen-water vapor environment. Some general conclusions can be made comparing the results of tests in a hydrogen environment with those in a hydrogen-water vapor environment. The hydrogen-water vapor environment caused a 50 percent average reduction in fatigue life, indicating extreme degradation when compared with tests conducted in air, for Incoloy 903 at 1033 K (1400 F). Crack growth rates increased significantly for all materials with increasing test temperature. A very significant increase (three orders of magnitude) in crack growth rate occurred for Incoloy 903 tested in the hydrogen-water vapor environment when compared with testing done in hydrogen along at 922 K (1200 F).

Warren, J. R.↗

NASA NTRS1977

Reaction rates for O3 + HCl yielding O + O2 + HCl, Cl + O3 yielding ClO + O2, and HCl + O yielding OH + Cl at elevated temperatures

Ozone and a much greater quantity of hydrogen chloride, slightly diluted by oxygen and argon, were heated by a shock wave process to temperatures in the range 480-1300 K at pressures from four to eight atmospheres. From variations in ozone concentration, determined by the attentuation of 2537-A radiation, the rate coefficient for the reaction O3 + HCl yielding O + O2 + HCl was determined to be k1 = (4.0 plus or minus 1.5) x 10 to the minus 10 exp(-10,408/T)cm3/s for temperatures of 480-720 K. From the concentration of ClO remaining at the end of ozone decomposition the rate coefficients for the reactions Cl + O3 yielding ClO + O2 and HCl + O yielding OH + Cl were also deduced for a temperature of about 1100 K.

Park, C.↗

NASA NTRS1977

Elevated-temperature flow strength, creep resistance and diffusion welding characteristics of Ti-gAl-2Nb-1Ta-0.8Mo

A study of the flow strength, creep resistance and diffusion welding characteristics of the titanium alloy Ti-6Al-2Nb-1Ta-0.8Mo was conducted. Two mill-processed forms of this alloy were examined. The forged material was essentially processed above the beta transus while the rolled form was subjected to considerable work below the beta transus. Between 1150 and 1250 K, the forged material was stronger and more creep resistant than the rolled alloy. Both forms exhibit superplastic characteristics in this temperature range. Strain measurements during diffusion welding experiments at 1200 K reveal that weld interfaces have no measurable effect on the overall creep deformation. Significant deformation appears to be necessary to produce a quality diffusion weld between superplastic materials. A 'soft' interlayer inserted between faying surfaces would seemingly allow manufacture of quality diffusion welds with little overall deformation.

Whittenberger, J. D.↗

NASA NTRS1978

Ultraviolet irradiation at elevated temperatures and thermal cycling in vacuum of FEP-A covered silicon solar cells

Experiments were designed and performed on silicon solar cells covered with heat-bonded FEP-A in an effort to explain the rapid degeneration of open-circuit voltage and maximum power observered on cells of this type included in an experiment on the ATS-6 spacecraft. Solar cells were exposed to ultraviolet light in vacuum at temperatures ranging from 30 to 105 C. The samples were then subjected to thermal cycling from 130 to -130 C. Inspection following irradiation indicated that all the covers remained physically intact. However, during the temperature cycling heat-bonded covers showed cracking. The test showed that heat-bonded FEP-A covers embrittle during UV exposure and the embrittlement is dependent upon sample temperature during irradiation. The results of the experiment suggest a probable mechanism for the degradation of the FEP-A cells on ATS-6.

Broder, J. D.↗

NASA NTRS1978

Development of methodology for optimum design of structures at elevated temperatures

This paper surveys a number of activities aimed at applying optimum design techniques to structures where high temperatures are important design considerations. An improved variant of fully-stressed design (FSD), denoted thermal fully-stressed design (TFSD), is described which converges significantly faster than FSD for problems where thermal stresses are comparable in magnitude to mechanical stresses. Second, an optimality criterion is described for sizing structures subjected to temperature constraints. Simultaneous requirements on strength and temperatures are handled by two different techniques: (1) a state-of-the-art mathematical programming method and (2) the optimality criterion technique for temperature constraints combined with FSD for strength constraints. A method is described to optimize the insulation and ply thicknesses of an insulated composite panel with a time-varying temperature applied to the outer surface of the insulation and a general set of in-plane loads applied to the panel.

Adelman, H. M.↗

NASA NTRS1978

Polymorphism and the crystal structures of InSb at elevated temperature and pressure

The paper presents polycrystalline X-ray diffraction data for three high-pressure phases of InSb. The study employed two types of diamond-anvil pressure cells. The X-ray diffraction parameters were recorded at different fixed pressures and temperatures on flat film. The experiment utilized Zr-filtered Mo radiation. The intensities were estimated from the X-ray photographs using a semiautomated microdensitometer.

Yu, S.-C.↗

NASA NTRS1980

Redundant structures at elevated temperatures

In many structural systems, it is desirable to perform analysis to determine how safe structure is when subjected to "yielding" loads. FRAME1 computer program analyzes, in both plastic and elastic ranges, redundant structures subjected to thermal and mechanical loads.

Guidry, L. I.↗

NASA NTRS1978

Elevated temperature properties of boron/aluminum composites

The high temperature properties of boron/aluminum composites, fabricated by an air diffusion bonding technique utilizing vacuum-bonded monolayer tape are reported. Seventeen different combinations of matrix alloy, reinforcement diameter, reinforcement volume percent, angle-ply and matrix enhancement (i.e. titanium cladding and interleaves) were fabricated, inspected, and tested. It is shown that good to excellent mechanical properties could be obtained for air-bonded boron/aluminum composites and that these properties did not decrease significantly up to a test temperature of at least 260 C. Composites made with 8 mil B/W fiber show a much greater longitudinal strength dependence on volume percent fiber than composites made with 5.6 mil fiber. The addition of titanium caused difficulties in composite bonding and yielded composites with reduced strength.

Sullivan, P. G.↗

NASA NTRS1979

Elevated temperature flow strength, creep resistance and diffusion welding characteristics of Ti-6Al-2Nb-1Ta-0.8Mo

A study of the flow strength, creep resistance and diffusion welding characteristics of the titanium alloy Ti-6Al-2Nb-1Ta-0.8Mo has been conducted. Two mill-processed forms of this alloy were examined. The forged material had been processed above the beta transus (approximately 1275 K) while the rolled form had been subjected to work below the beta transus. Between 1150 and 1250 K, the forged material was stronger and more creep resistant than the rolled alloy. Both forms exhibit superplastic characteristics in this temperature range. Strain measurements during diffusion welding experiments at 1200 K reveal that weld interfaces have no measurable effect on the overall creep deformation. Significant deformation appears to be necessary to produce a quality diffusion weld between superplastic materials. A 'soft' interlayer inserted between faying surfaces would seemingly allow manufacture of quality diffusion welds with little overall deformation.

Whittenberger, J. D.↗

NASA NTRS1980

Some useful concepts for the designer in treating cumulative fatigue damage at elevated temperatures

The paper concentrates on three subjects: (1) further development of the double-linear damage rule for cumulative fatigue damage summation in the sub-creep temperature range; (2) a new consideration of the effect of strain reversals in the creep range of materials, whereby reversals that occur later in the histogram can influence the degree of damage caused by earlier loading events; and (3) the application of the minimum-commitment time-temperature parameter to the treatment of creep rupture of multiheats wherein considerable differences in properties of individual heats may occur. Numerical examples and plots are given.

Manson, S. S.↗

NASA NTRS1980

Experimental Study of the Stability of Aircraft Fuels at Elevated Temperatures

An experimental study of fuel stability was conducted in an apparatus which simulated an aircraft gas turbine fuel system. Two fuels were tested: Jet A and Number 2 Home Heating oil. Jet A is an aircraft gas turbine fuel currently in wide use. No. 2HH was selected to represent the properties of future turbine fuels, particularly experimental Reference Broad Specification, which, under NASA sponsorship, was considered as a possible next-generation fuel. Tests were conducted with varying fuel flow rates, delivery pressures and fuel pretreatments (including preheating and deoxygenation). Simulator wall temperatures were varied between 422K and 672K at fuel flows of 0.022 to 0.22 Kg/sec. Coking rate was determined at four equally-spaced locations along the length of the simulator. Fuel samples were collected for infrared analysis. The dependence of coking rate in Jet A may be correlated with surface temperature via an activation energy of 9 to 10 kcal/mole, although the results indicate that both bulk fluid and surface temperature affect the rate of decomposition. As a consequence, flow rate, which controls bulk temperature, must also be considered. Taken together, these results suggest that the decomposition reactions are initiated on the surface and continue in the bulk fluid. The coking rate data for No. 2 HH oil are very highly temperature dependent above approximately 533K. This suggests that bulk phase reactions can become controlling in the formation of coke.

Vranos, A.↗

NASA NTRS1980

Notched graphite polymimide composites at room and notched graphite polymide composites at room and elevated temperatures

The fracture behavior in graphite/polyimide (Gr/PI) Celion 6000/PMR-15 composites was characterized. Emphasis was placed on the correlation between the observed failure modes and the deformation characteristics of center-notched Gr/Pl laminates. Crack tip damage growth, fracture strength and notch sensitivity, and the associated characterization methods were also examined. Special attention was given to nondestructive evaluation of internal damage and damage growth, techniques such as acoustic emission, X-ray radiography, and ultrasonic C-scan. Microstructural studies using scanning electron microscopy, photomicrography, and the pulsed nuclear magnetic resonance technique were employed as well. All experimental procedures and techniques are described and a summary of representative results for Gr/Pl laminates is given.

Awerbuch, J.↗

NASA NTRS1982

Performance characteristics of an electric vehicle lead-acid battery pack at elevated temperatures

Discharge testing data electric car battery pack over initial electrolyte temperature variations between 27 and 55 C are presented. The tests were conducted under laboratory conditions and then compared to detailed electric vehicle simulation models. Battery discharge capacity increased with temperature for constant current discharges, and battery energy capacity increased with temperature for constant power discharges. Dynamometer tests of the electric test vehicle showed an increase in range of 25% for the higher electrolyte temperature.

Chapman, P.↗

NASA NTRS1982

Microstructural effects on the room and elevated temperature low cycle fatigue behavior of Waspaloy

Longitudinal specimens of Waspaloy containing either coarse grains with small gamma or fine grains with large gamma were tested in air at a frequency of 0.33 Hz or 0.50 Hz. The coarse grained structures exhibited planar slip on (III) planes and precipitate shearing at all temperatures. Cracks initiated by a Stage 1 mechanism and propagated by a striation forming mechanism. At 700 C and 800 C, cleavage and intergranular cracking were observed. Testing at 500 C, 700 C, and 800 C caused precipitation of grain boundary carbides. At 700 C, carbides precipitated on slip bands. The fine grained structures exhibited planar slip on (111) planes. Dislocations looped the large gamma precipitates. This structure led to stress saturation and propagation was observed. Increasing temperatures resulted in increased specimen oxidation for both heat treatments. Slip band and grain boundary oxidation were observed. At 800 C, oxidized grain boundaries were cracked by intersecting slip bands which resulted in intergranular failure. The fine specimens had crack initiation later in the fatigue life, but with more rapid propagation crack propagation.

Lerch, B. A.↗

NASA NTRS1982

Failure mechanisms of thermal barrier coatings exposed to elevated temperatures

The failure of a ZrO2-8%Y2O3/Ni-14% Al-0.1% Zr coating system on Rene 41 in Mach 0.3 burner rig tests was characterized. High flame and metal temperatures were employed in order to accelerate coating failure. Failure by delamination was shown to precede surface cracking or spalling. This type of failure could be duplicated by cooling down the specimen after a single long duration isothermal high temperature cycle in a burner rig or a furnace, but only if the atmosphere was oxidizing. Stresses due to thermal expansion mismatch on cooling coupled with the effects of plastic deformation of the bond coat and oxidation of the irregular bond coat are the probable life limiting factors. Heat up stresses alone could not fail the coating in the burner rig tests. Spalling eventually occurs on heat up but only after the coating has already failed through delamination.

Miller, R. A.↗

NASA NTRS1981

Electrical conductivity and electron-spin resonance in oxidatively stabilized polyacrylonitrile subjected to elevated temperature

Electrical conductivity and electron spin resonance measurements are presented for oxidatively stabilized polyacrylonitrile (PAN) fibers subjected to heat treatment at temperatures ranging from 700 to 950 K. Conductivity measurements made at temperatures between 77 and 523 K reveal that PAN fibers heat treated in vacuum behave as semiconductors, with a room-temperature conductivity dominated by the contributions of impurity states, with an activation energy of 88 kcal/mole. A decrease in conductivity is observed upon air which is attributed to a decrease in the electron-phonon scattering time. ESR spectra indicate that conducting pathways having metallic properties are formed at temperatures as low as 715 K, although the contribution of these pathways to the room-temperature conductivity is extremely small next to the contribution of localized spin centers.

Lerner, N. R.↗