Search NASA⌕ Search

SEARCH · Search NASA

Results for “finite measurement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

Comparison of undulation difference accuracies using gravity anomalies and gravity disturbances

Errors in the outer zone contribution to oceanic undulation differences computed from a finite set of potential coefficients based on satellite measurements of gravity anomalies and gravity disturbances are analyzed. Equations are derived for the truncation errors resulting from the lack of high-degree coefficients and the commission errors arising from errors in the available lower-degree coefficients, and it is assumed that the inner zone (spherical cap) is sufficiently covered by surface gravity measurements in conjunction with altimetry or by gravity anomaly data. Numerical computations of error for various observational conditions reveal undulation difference errors ranging from 13 to 15 cm and from 6 to 36 cm in the cases of gravity anomaly and gravity disturbance data, respectively for a cap radius of 10 deg and mean anomalies accurate to 10 mgal, with a reduction of errors in both cases to less than 10 cm as mean anomaly accuracy is increased to 1 mgal. In the absence of a spherical cap, both cases yield error estimates of 68 cm for an accuracy of 1 mgal and between 93 and 160 cm for the lesser accuracy, which can be reduced to about 110 cm by the introduction of a perfect 30-deg reference field.

Jekeli, C.↗

Studies of sidewall boundary layer in the Langley 0.3 meter transonic cryogenic tunnel with and without suction

Boundary layer measurements on the sidewalls of the Langley 0.3 Meter Transonic Cryogenic Tunnel were made to determine the effectiveness of the passive boundary layer bleed system over a Reynolds number range from 20 to 200 x 10 to the sixth power per meter at Mach numbers from 0.30 to 0.76. The tunnel sidewall boundary layer displacement thickness was about 2 percent of the width of the test section without the boundary layer bleed. Measured velocity profiles correlated well with the defect law of Hama. With the boundary layer bleed equivalent to about 2 percent of the test section mass flow, the boundary layer displacement thickness reduced to about 1 percent of the test section width, which is generally considered acceptable for testing airfoils. It was also noticed that effectiveness of the bleed was nearly independent of the Mach number and Reynolds number over the range of conditions tested. A comparison of the measured suction effectiveness of the bleed with the finite difference and integral methods of boundary layer calculation showed good agreement.

Murthy, A. V.↗

Evaluation and mitigation of lightning hazards to the space shuttle Solid Rocket Motors (SRM)

The objective was to quantify electric field strengths in the Solid Rocket Motor (SRM) propellant in the event of a worst case lightning strike. Using transfer impedance measurements for selected lightning protection materials and 3D finite difference modeling, a retrofit design approach for the existing dielectric grain cover and railcar covers was evaluated and recommended for SRM segment transport. A safe level of 300 kV/m was determined for the propellant. The study indicated that a significant potential hazard exists for unprotected segments during rail transport. However, modified railcar covers and grain covers are expected to prevent lightning attachment to the SRM and to reduce the levels to several orders of magnitude below 300 kV/m.

Rigden, Gregory J.↗

Acoustical analysis of gear housing vibration

The modal and acoustical analysis of the NASA gear-noise rig is described. Experimental modal analysis techniques were used to determine the modes of vibration of the transmission housing. The resulting modal data were then used in a boundary element method (BEM) analysis to calculate the sound pressure and sound intensity on the surface of the housing as well as the radiation efficiency of each mode. The radiation efficiencies of the transmission housing modes are compared with theoretical results for finite, baffled plates. A method that uses the measured mode shapes and the BEM to predict the effect of simple structural changes on the sound radiation efficiency of the modes of vibration is also described.

Seybert, A. F.↗

Hybrid scaled structural dynamic models and their use in damping prediction

Analytical and experimental techniques for the prediction and ground verification of the damped structural dynamics of space structures are developed. The options available for similarity-scaled model testing, including replica and multiple scale approaches, are reviewed. For the case when the distortion of potentially dissipative or nonlinear joints, which would be required in multiple-scale modeling, is impractical, a new type of modeling is introduced, which uses a hybrid of joints at replica scale and connecting elements at a modified multiple scale. The model design requirements for replica, multiple-scale, and hybrid models are developed, and the expected scaling of nonlinear dissipation in joints is derived. A damping prediction scheme is developed that relies on a finite element model of the undamped structure and measurements of the individual joint properties to predict the modal damping of the truss attributable to the joints. A hybrid-scaled model of a segment of the Space Station was built and dynamically tested. The predicted and measured truss damping compared favorably.

Crawley, Edward F.↗

Nonlinear analysis of AS4/PEEK thermoplastic composite laminate using a one parameter plasticity model

A one-parameter plasticity model was shown to adequately describe the orthotropic plastic deformation of AS4/PEEK (APC-2) unidirectional thermoplastic composite. This model was verified further for unidirectional and laminated composite panels with and without a hole. The nonlinear stress-strain relations were measured and compared with those predicted by the finite element analysis using the one-parameter elastic-plastic constitutive model. The results show that the one-parameter orthotropic plasticity model is suitable for the analysis of elastic-plastic deformation of AS4/PEEK composite laminates.

Sun, C. T.↗

Elastic-plastic analysis of AS4/PEEK composite laminate using a one-parameter plasticity model

A one-parameter plasticity model was shown to adequately describe the plastic deformation of AS4/PEEK (APC-2) unidirectional thermoplastic composite. This model was verified further for unidirectional and laminated composite panels with and without a hole. The elastic-plastic stress-strain relations of coupon specimens were measured and compared with those predicted by the finite element analysis using the one-parameter plasticity model. The results show that the one-parameter plasticity model is suitable for the analysis of elastic-plastic deformation of AS4/PEEK composite laminates.

Sun, C. T.↗

Numerical simulation of aerothermal loads in hypersonic engine inlets due to shock impingement

The effect of shock impingement on an axial corner simulating the inlet of a hypersonic vehicle engine is modeled using a finite-difference procedure. A three-dimensional dynamic grid adaptation procedure is utilized to move the grids to regions with strong flow gradients. The adaptation procedure uses a grid relocation stencil that is valid at both the interior and boundary points of the finite-difference grid. A linear combination of spatial derivatives of specific flow variables, calculated with finite-element interpolation functions, are used as adaptation measures. This computational procedure is used to study laminar and turbulent Mach 6 flows in the axial corner. The description of flow physics and qualitative measures of heat transfer distributions on cowl and strut surfaces obtained from the analysis are compared with experimental observations. Conclusions are drawn regarding the capability of the numerical scheme for enhanced modeling of high-speed compressible flows.

Ramakrishnan, R.↗

Acoustical analysis of gear housing vibration

The modal and acoustical analysis of the NASA gear-noise rig is described. Experimental modal analysis techniques were used to determine the modes of vibration of the transmission housing. The resulting modal data were then used in a boundary element method (BEM) analysis to calculate the sound pressure and sound intensity on the surface of the housing as well as the radiation efficiency of each mode. The radiation efficiencies of the transmission housing modes are compared with theoretical results for finite, baffled plates. A method that uses the measured mode shapes and the BEM to predict the effect of simple structural changes on the sound radiation efficiency of the modes of vibration is also described.

Seybert, A. F.↗

Detecting Structural Failures Via Acoustic Impulse Responses

Advanced method of acoustic pulse reflectivity testing developed for use in determining sizes and locations of failures within structures. Used to detect breaks in electrical transmission lines, detect faults in optical fibers, and determine mechanical properties of materials. In method, structure vibrationally excited with acoustic pulse (a "ping") at one location and acoustic response measured at same or different location. Measured acoustic response digitized, then processed by finite-impulse-response (FIR) filtering algorithm unique to method and based on acoustic-wave-propagation and -reflection properties of structure. Offers several advantages: does not require training, does not require prior knowledge of mathematical model of acoustic response of structure, enables detection and localization of multiple failures, and yields data on extent of damage at each location.

Bayard, David S.↗

Coupling Between Microstrip Lines with Finite Width Ground Plane Embedded in Polyimide Layers for 3D-MMICs on Si

Three-dimensional circuits built upon multiple layers of polyimide are required for constructing Si/SiGe monolithic microwave/millimeter-wave integrated circuits on complementary metal oxide semiconductor (CMOS) (low resistivity) Si wafers. Thin film microstrip lines (TFMS) with finite width ground planes embedded in the polyimide are often used. However, the closely spaced TFMS lines are susceptible to high levels of coupling, which degrades circuit performance. In this paper, Finite Difference Time Domain (FDTD) analysis and experimental measurements are used to show that the ground planes must be connected by via holes to reduce coupling in both the forward and backward directions.

Ponchak, George E.↗

Coupling Between Microstrip Lines With Finite Width Ground Plane Embedded in Thin Film Circuits

Three-dimensional (3D) interconnects built upon multiple layers of polyimide are required for constructing 3D circuits on CMOS (low resistivity) Si wafers, GaAs, and ceramic substrates. Thin film microstrip lines (TFMS) with finite width ground planes embedded in the polyimide are often used. However, the closely spaced TFMS lines a r e susceptible to high levels of coupling, which degrades circuit performance. In this paper, Finite Difference Time Domain (FDTD) analysis and experimental measurements a r e used to show that the ground planes must be connected by via holes to reduce coupling in both the forward and backward directions. Furthermore, it is shown that coupled microstrip lines establish a slotline type mode between the two ground planes and a dielectric waveguide type mode, and that the via holes recommended here eliminate these two modes.

Ponchak, George E.↗

Experiments on the Flow of a Thin Liquid Film Over a Horizontal Stationary and Rotating Disk Surface

Experiments on characterization of thin liquid films flowing over stationary and rotating disk surfaces are described. The thin liquid film was created by introducing deionized water from a flow collar at the center of an aluminum disk with a known initial film thickness and uniform radial velocity. Radial film thickness distribution was measured using a non-intrusive laser light interface reflection technique that enabled the measurement of the instantaneous film thickness over a finite segment of the disk. Experiments were performed for a range of flow rates between 3.01pm and 15.01pm, corresponding to Reynolds numbers based on the liquid inlet gap height and velocity between 238 and 1,188. The angular speed of the disk was varied from 0 rpm to 300 rpm. When the disk was stationary, a circular hydraulic jump was present in the liquid film. The liquid-film thickness in the subcritical region (down-stream of the hydraulic jump) was an order of magnitude greater than that in the supercritical region (upstream of the hydraulic jump) which was of the order of 0.3 mm. As the Reynolds number increased, the hydraulic jump migrated toward the edge of the disk. In the case of rotation, the liquid-film thickness exhibited a maximum on the disk surface. The liquid-film inertia and friction influenced the inner region where the film thickness progressively increased. The outer region where the film thickness decreased was primarily affected by the centrifugal forces. A flow visualization study of the thin film was also performed to determine the characteristics of the waves on the free surface. At high rotational speeds, spiral waves were observed on the liquid film. It was also determined that the angle of the waves which form on the liquid surface was a function of the ratio of local radial to tangential velocity.

Ozar, B.↗

Applications of Displacement Transfer Functions to Deformed Shape Predictions of the G-III Swept-Wing Structure

In support of the Adaptive Compliant Trailing Edge [ACTE] project at the NASA Armstrong Flight Research Center, displacement transfer functions were applied to the swept wing of a Gulfstream G-III airplane (Gulfstream Aerospace Corporation, Savannah, Georgia) to obtain deformed shape predictions. Four strainsensing lines (two on the lower surface, two on the upper surface) were used to calculate the deformed shape of the G III wing under bending and torsion. There being an insufficient number of surface strain sensors, the existing G III wing box finite element model was used to generate simulated surface strains for input to the displacement transfer functions. The resulting predicted deflections have good correlation with the finite-element generated deflections as well as the measured deflections from the ground load calibration test. The convergence study showed that the displacement prediction error at the G III wing tip can be reduced by increasing the number of strain stations (for each strain-sensing line) down to a minimum error of l.6 percent at 17 strain stations; using more than 17 strain stations yielded no benefit because the error slightly increased to 1.9% when 32 strain stations were used.

displacement theory↗

Detached Melt and Vapor Growth of InI in SUBSA Furnace

Indium iodide (InI) is a promising wide energy band gap nuclear detector material. It is ideal for space experiments because it is non-toxic and has a relatively low melting point of only 351 degrees Centigrade. However, it has been established that melt-grown crystals contain a large amount of second phase inclusions/precipitates. The typical size of inclusions are 1 to 27 microns in diameter, while the volume fraction of all sizes is 300 to 600 parts per million. The SEM-EDS (Scanning Electron Microscopy / Energy Dispersive X-Ray Spectroscopy) analysis of the inclusions has revealed that they all contain oxygen and some contain carbon. At present, under sponsorship of NASA and CASIS (Center for the Advancement of Science in Space), we are conducting ground-based experiments with InI in preparation for the flight experiments to be conducted in the SUBSA (Solidification Using a Baffle in Sealed Ampoules) furnace in the Microgravity Science Glovebox at the International Space Station, planned for the summer/fall of 2017. Earth-based experiments include melt and vapor growth conducted in the SUBSA ground unit, measurements of the volumetric expansion coefficient of the melt, and measurements of the wetting angle of molten InI. Finite element modeling has been conducted to optimize the design of the flight ampoules. Alloying with Tl and Ga has given promising results.

Ostrogorsky, A. G.↗

Magnetic Shield Design Modeling and Validation for SWOT Spacecraft Ka-Band Extended Interaction Klystron

Two Extended Interaction Klystrons (EIKs) containing strong permanent magnets were modeled magnetically in a representative spacecraft geometry using commercial finite element modeling techniques and were validated against measurements made at varying distances. Initial modeling results for the 63 A-m2 (amperes per square meter) dipole moment magnets showed that magnetic shields would be necessary in order to meet magnetic field requirements for the Surface Water and Ocean Topography (SWOT) spacecraft, which contains components that are susceptible to external DC (Direct Current) magnetic fields. JPL (Jet Propulsion Laboratory) and the EIK vendor proposed cold rolled steel and mu-metal as potential shield materials along with proposed thicknesses of 0.5 millimeters and 1.5 millimeters. Magnetic shields made from each of these materials were designed and modeled in software, taking high-field saturation into account. Prototype magnetic shields with these parameters were then built, measured with an existing EIK, and compared against modeling results. For single-axis field measurements along the dipole axis, modeling results were within 7 gauss of the measured values at 10 centimeters from the magnet, and converged to less than 1.5 gauss at distances greater than 14 centimeters from the magnet. Three-axis field measurements at locations of interest showed that model correlation improved to within 4 gauss at 11 centimeters and 2 gauss for distances ranging between 15 centimeters and 36 centimeters.

Gonzales, Edward↗

Magnetic Shield Design Modeling and Validation for SWOT Spacecraft Ka-Band Extended Interaction Klystron

Two Extended Interaction Klystrons (EIKs) containing strong permanent magnets were modeled magnetically in a representative spacecraft geometry using commercial finite element modeling techniques and were validated against measurements made at varying distances. Initial modeling results for the 63 A-m2 dipole moment magnets showed that magnetic shields would be necessary in order to meet magnetic field requirements for the Surface Water and Ocean Topography (SWOT) spacecraft, which contains components that are susceptible to external DC magnetic fields. JPL and the EIK vendor proposed cold rolled steel and mu-metal as potential shield materials along with proposed thicknesses of 0.5 mm and 1.5 mm. Magnetic shields made from each of these materials were designed and modeled in software, taking highfield saturation into account. Prototype magnetic shields with these parameters were then built, measured with an existing EIK, and compared against modeling results. For single-axis field measurements along the dipole axis, modeling results were within 7 gauss of the measured values at 10 cm from the magnet, and converged to less than 1.5 gauss at distances greater than 14 cm from the magnet. Three-axis field measurements at locations of interest showed that model correlation improved to within 4 gauss at 11 cm and 2 gauss for distances ranging between 15 cm and 36 cm.

Gonzales, Edward↗