Search NASA⌕ Search

SEARCH · Search NASA

Results for “flaps”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS1954

Effect of a Leading-edge Flap upon the Lift, Drag, and Pitching Moment of an Airplane Employing a Thin, Unswept Wing

The effects of deflecting full-span, constant-chord, leading-edge flaps, having either round or sharp leading edges, upon the lift, drag,. and pitching moment characteristics of a model of an interceptor-type aircraft have been determined experimentally at subsonic and supersonic speeds. Results indicate that the variations of lift with angle of attack and of pitching moment with lift were unaffected by either the shape of the flap leading edge or flap deflection. Deflection of the flaps having either a round or sharp leading edge increased the drag at zero lift at both subsonic and supersonic speeds. In spite of the increase in the drag at zero lift, however, deflection of the flaps increased the maximum lift-drag ratio at subsonic speeds and had no deleterious effect at supersonic speeds.

Heitmeyer, John C.↗
NASA NTRS2010

Low Speed and High Speed Correlation of SMART Active Flap Rotor Loads

Measured, open loop and closed loop data from the SMART rotor test in the NASA Ames 40- by 80- Foot Wind Tunnel are compared with CAMRAD II calculations. One open loop high-speed case and four closed loop cases are considered. The closed loop cases include three high-speed cases and one low-speed case. Two of these high-speed cases include a 2 deg flap deflection at 5P case and a test maximum-airspeed case. This study follows a recent, open loop correlation effort that used a simple correction factor for the airfoil pitching moment Mach number. Compared to the earlier effort, the current open loop study considers more fundamental corrections based on advancing blade aerodynamic conditions. The airfoil tables themselves have been studied. Selected modifications to the HH-06 section flap airfoil pitching moment table are implemented. For the closed loop condition, the effect of the flap actuator is modeled by increased flap hinge stiffness. Overall, the open loop correlation is reasonable, thus confirming the basic correctness of the current semi-empirical modifications; the closed loop correlation is also reasonable considering that the current flap model is a first generation model. Detailed correlation results are given in the paper.

Kottapalli, Sesi B. R.↗
NASA NTRS2015

Aeroelastic Analysis of a Flexible Wing Wind Tunnel Model with Variable Camber Continuous Trailing Edge Flap Design

This paper presents data analysis of a flexible wing wind tunnel model with a variable camber continuous trailing edge flap (VCCTEF) design for drag minimization tested at the University of Washington Aeronautical Laboratory (UWAL). The wind tunnel test was designed to explore the relative merit of the VCCTEF concept for improved cruise efficiency through the use of low-cost aeroelastic model test techniques. The flexible wing model is a 10%-scale model of a typical transport wing and is constructed of woven fabric composites and foam core. The wing structural stiffness in bending is tailored to be half of the stiffness of a Boeing 757-era transport wing while the torsional stiffness is about the same. This stiffness reduction results in a wing tip deflection of about 10% of the wing semi-span. The VCCTEF is a multi-segment flap design having three chordwise camber segments and five spanwise flap sections for a total of 15 individual flap elements. The three chordwise camber segments can be positioned appropriately to create a desired trailing edge camber. Elastomeric material is used to cover the gaps in between the spanwise flap sections, thereby creating a continuous trailing edge. Wind tunnel data analysis conducted previously shows that the VCCTEF can achieve a drag reduction of up to 6.31% and an improvement in the lift-to-drag ratio (L=D) of up to 4.85%. A method for estimating the bending and torsional stiffnesses of the flexible wingUWAL wind tunnel model from static load test data is presented. The resulting estimation indicates that the stiffness of the flexible wing is significantly stiffer in torsion than in bending by as much as 9 to 1. The lift prediction for the flexible wing is computed by a coupled aerodynamic-structural model. The coupled model is developed by coupling a conceptual aerodynamic tool Vorlax with a finite-element model of the flexible wing via an automated geometry deformation tool. Based on the comparison of the lift curve slope, the lift prediction for the rigid wing is in good agreement with the estimated lift coefficients derived from the wind tunnel test data. Due to the movement of the VCCTEF during the wind tunnel test, uncertainty in the lift prediction due to the indicated variations of the VCCTEF deflection is studied. The results show a significant spread in the lift prediction which contradicts the consistency in the aerodynamic measurements, thus suggesting that the indicated variations as measured by the VICON system may not be reliable. The lift prediction of the flexible wing agrees very well with the measured lift curve for the baseline configuration. The computed bending deflection and wash-out twist of the flexible wing also match reasonably well with the aeroelastic deflection measurements. The results demonstrate the validity of the aerodynamic-structural tool for use to analyze aerodynamic performance of flexible wings.

Wind Tunnel↗
NASA NTRS2017

Maven Observations of Tail Current Sheet Flapping at Mars

The Martian magnetotail is a complex regime through which atmospheric particles are lost to space. Our current understanding of Mars' tail continues to develop with the comprehensive particle and field data collected by Mars Atmosphere and Volatile EvolutioN (MAVEN). In this work, we identify periods when MAVEN encounters multiple current sheet crossings through a single tail traversal in order to understand tail dynamics. We apply an analysis technique that has been developed and validated by using multipoint measurements in order to separate the spatial and temporal properties associated with current sheet flapping. Events are classified into periods of steady flapping, due to a global motion of the current sheet, and kink-like flapping, resulting from localized wave propagation along the tail current sheet. Out of 106 periods during which multiple current sheet crossings were observed, 20 were due to steady flapping and 10 from kink-like flapping. A majority of the kink-like events resulted from waves propagating in the opposite direction of the solar wind convection electric field, regardless of their location in the tail, unlike at Earth and Venus. This finding suggests that possible magnetosphere energy sources, whereby plasma is accelerated and removed from the Martian environment, are not located in the central magnetotail; rather, these waves may be driven by a source located at the tail flank based on the direction of the solar wind electric field. Therefore, by identifying potential sources of impulsive energy release in the tail, we may better understand mechanisms that drive atmospheric loss at Mars.

Atmospheric Particles↗
NASA NTRS2015

Optimized Off-Design Performance of Flexible Wings with Continuous Trailing-Edge Flaps

This work assesses the potential aerodynamic performance benefits of a variable-camber, continuous-trailing-edge flap system on a generic transport aircraft at off-design conditions. A process to optimize transport wings while addressing static aeroelastic effects is presented. To establish a proper baseline, a transport wing is first aerodynamically optimized at a mid-cruise flight condition using an inviscid, aeroelastic analysis tool. The optimized wing is then analyzed at off-design cruise conditions. The optimization is repeated at these off-design conditions to determine how much performance is lost by the wing optimized solely for the mid-cruise condition. The full-span flap system is then adapted to improve performance of the mid-cruise-optimized wing at these off-design conditions. The measured improvement is quantified by a comparison with wings designed specifically for the off-design conditions. To evaluate the effects of aeroelasticity on the effectiveness of the flap system, this entire process is performed on both a conventionally stiff wing and a modern, more flexible wing. The results indicate that the flap system allows for recovery of near-optimal performance throughout cruise. The flap system is found to be advantageous even for modern wings with increased flexibility.

Rodriguez, David L.↗
NASA NTRS2014

Experimental Investigation of a Flexible Wing with a Variable Camber Continuous Trailing Edge Flap Design

This paper presents experimental results of a flexible wing wind tunnel model with a variable camber continuous trailing edge flap (VCCTEF) design for drag minimization, tested at the University of Washington Aeronautical Labo- ratory (UWAL). The wind tunnel test was designed to explore the relative merit of the VCCTEF concept for improved cruise efficiency through the use of low-cost aeroelastic model test techniques. The flexible wing model is a 10-scaled model of a typical transport wing and is constructed of woven fabric composites and foam core. The wing structural stiffness in bending is tailored to be half of the stiffness of a Boeing 757-era transport wing, while the torsional stiffness is about the same. This stiffness reduction results in a wing tip deflection of about 10 of the wing semi-span. The VCCTEF is a multi-segment flap design having three chordwise camber segments and five spanwise flap sections for a total of 15 individual flap elements. The three chordwise camber segments can be positioned appropriately to create a desired trailing edge camber. Elastomeric material is used to cover the gaps in between the spanwise flap sections, thereby creating a continuous trailing edge. Wind tunnel data indicate a high degree of data correlation and repeata- bility. The VCCTEF can achieve a drag reduction of up to 6.31 and an improvement in the lift-to-drag ratio (LD) of up to 4.85. The paper also presents two methods for estimating the lift coefficient of a rigid wing using a dynamic pressure correction and an aeroelastic deflection correction. Both methods provide good estimates of the rigid-wing lift coefficient.

Aerodynamics↗
NASA NTRSDate not supplied

Pterodactyl: Aerodynamic and Aerothermal Modeling for a Symmetric Deployable Earth Entry Vehicle with Flaps

NASA’s Pterodactyl project has investigated a deployable atmospheric entry vehicle integrated with a flap control system that provides precision targeting during reentry. The control system consists of eight flaps mounted at the edge of a heatshield that can deflect in and out of the flow. An aerodynamic and aerothermodynamic analysis process was developed for preliminary vehicle design and aerodynamic database generation using engineering and CFD tools with varying levels of fidelity. The objective of this analysis was to: 1) understand the inherent aerodynamics, 2) provide an aerodynamics database for stability and control analysis, and 3) provide qualitative and quantitative aeroheating analysis for Thermal Protection System modeling of the flaps. A high fidelity Euler code, Cart3D, was used to resolve complex flow features such as secondary shocks and shock impingement. A wide range of supersonic (Mach 2) and hypersonic Mach numbers (up to Mach 40) were tested with an Earth atmosphere model. A process was developed to utilize the adaptive volume mesh generator utility of the perfect gas model of Cart3D to create meshes with high cell efficiency and numerical stability prior to running a 2nd order accurate solution with a real gas model. High-fidelity aerothermal CFD simulations were performed using US3D to further improve the aerothermal analysis on hypersonic flow around a complex entry vehicle shape including viscosity, chemical reactions of air species, vibrational energy, and catalytic surface reactions. In this process, it was found that the flap control system provided multi-axis control that can be utilized for entry precision targeting. Additionally, the Pterodactyl vehicle can achieve up to a trim L/D of 0.2. Finally, the increased fidelity of the aerothermal heating environments revealed that the shear stress contributes to increasing the heating on the flaps.

Deployable Entry Vehicle↗
NASA NTRSDate not supplied

Pterodactyl: Aerodynamic and Aerothermal Modeling for a Symmetric Deployable Earth Entry Vehicle with Flaps

NASA’s Pterodactyl project has investigated a deployable atmospheric entry vehicle integrated with a flap control system that provides precision targeting during reentry. The control system consists of eight flaps mounted at the edge of a heatshield that can deflect in and out of the flow. An aerodynamic and aerothermodynamic analysis process was developed for preliminary vehicle design and aerodynamic database generation using engineering and CFD tools with varying levels of fidelity. The objective of this analysis was to: 1) understand the inherent aerodynamics, 2) provide an aerodynamics database for stability and control analysis, and 3) provide qualitative and quantitative aeroheating analysis for Thermal Protection System modeling of the flaps. A high fidelity Euler code, Cart3D, was used to resolve complex flow features such as secondary shocks and shock impingement. A wide range of supersonic (Mach 2) and hypersonic Mach numbers (up to Mach 40) were tested with an Earth atmosphere model. A process was developed to utilize the adaptive volume mesh generator utility of the perfect gas model of Cart3D to create meshes with high cell efficiency and numerical stability prior to running a 2nd order accurate solution with a real gas model. High-fidelity aerothermal CFD simulations were performed using US3D to further improve the aerothermal analysis on hypersonic flow around a complex entry vehicle shape including viscosity, chemical reactions of air species, vibrational energy, and catalytic surface reactions. In this process, it was found that the flap control system provided multi-axis control that can be utilized for entry precision targeting. Additionally, the Pterodactyl vehicle can achieve up to a trim L/D of 0.2. Finally, the increased fidelity of the aerothermal heating environments revealed that the shear stress contributes to increasing the heating on the flaps.

Deployable Entry Vehicle↗
NASA NTRS2017

MAVEN observations of tail current sheet flapping at Mars

The Martian magnetotail is a complex regime through which atmospheric particles are lost to space. Our current understanding of Mars' tail continues to develop with the comprehensive particle and field data collected by Mars Atmosphere and Volatile EvolutioN (MAVEN). In this work, we identify periods when MAVEN encounters multiple current sheet crossings through a single tail traversal in order to understand tail dynamics. We apply an analysis technique that has been developed and validated by using multipoint measurements in order to separate the spatial and temporal properties associated with current sheet flapping. Events are classified into periods of steady flapping, due to a global motion of the current sheet, and kink‐like flapping, resulting from localized wave propagation along the tail current sheet. Out of 106 periods during which multiple current sheet crossings were observed, 20 were due to steady flapping and 10 from kink‐like flapping. A majority of the kink‐like events resulted from waves propagating in the opposite direction of the solar wind convection electric field, regardless of their location in the tail, unlike at Earth and Venus. This finding suggests that possible magnetosphere energy sources, whereby plasma is accelerated and removed from the Martian environment, are not located in the central magnetotail; rather, these waves may be driven by a source located at the tail flank based on the direction of the solar wind electric field. Therefore, by identifying potential sources of impulsive energy release in the tail, we may better understand mechanisms that drive atmospheric loss at Mars.

Gina A. DiBraccio↗
NASA NTRS1948

Tests of a Triangular Wing of Aspect Ratio 2 in the Ames 12-foot Pressure Wind Tunnel III : the Effectiveness and Hinge Moments of a Skewed Wing-tip Flap

Results of wind-tunnel tests of a semispan model of a triangular wing of aspect ratio 2 with a skewed wing-tip flap are presented. Lift, drag, pitching-moment, and hinge-moment data are included for subsonic Mach numbers up to 0.95. The flap showed extremely high hinge moments and low effectiveness as a longitudinal control. Although less affected by compressibility, this flap is indicated to be inferior to a constant-chord flap when applied to this triangular wing.

MACH NUMBER EFFECTS - COMPLETE WINGS↗
NASA NTRS1943

Wind-Tunnel Investigation of a Low-Drag Airfoil Section with a Double Slotted Flap

Tests were made of an 0.309-chord double-slotted flap on an NACA 65, 3-118, a equals 1.0 airfoil section to determine drag, lift, and pitching-moment characteristics for a range of flap deflections. Results indicate that combination of a low-drag airfoil and a double-slotted flap, of which the two parts moved as a single unit, gave higher maximum lift coefficients than have been obtained with plain, split, or slotted flaps on low-drag airfoils. Pitching moments were comparable to those obtained with other high-lift devices on conventional airfoils for similar lift coefficients.

AIRFOILS - NACA 65,3-118-CHAR , MOMENTS & ORDINATE↗
NASA NTRS2014

Application of Sequential Quadratic Programming to Minimize Smart Active Flap Rotor Hub Loads

In an analytical study, SMART active flap rotor hub loads have been minimized using nonlinear programming constrained optimization methodology. The recently developed NLPQLP system (Schittkowski, 2010) that employs Sequential Quadratic Programming (SQP) as its core algorithm was embedded into a driver code (NLP10x10) specifically designed to minimize active flap rotor hub loads (Leyland, 2014). Three types of practical constraints on the flap deflections have been considered. To validate the current application, two other optimization methods have been used: i) the standard, linear unconstrained method, and ii) the nonlinear Generalized Reduced Gradient (GRG) method with constraints. The new software code NLP10x10 has been systematically checked out. It has been verified that NLP10x10 is functioning as desired. The following are briefly covered in this paper: relevant optimization theory; implementation of the capability of minimizing a metric of all, or a subset, of the hub loads as well as the capability of using all, or a subset, of the flap harmonics; and finally, solutions for the SMART rotor. The eventual goal is to implement NLP10x10 in a real-time wind tunnel environment.

HUB LOADS↗
NASA NTRS2021

Aircraft Flaps Modeling in OpenMDAO

The goal of this project was to develop a model for a single subsystem in the aerodynamics discipline, in this case the flaps of an aircraft. Flaps are high-lift devices used by planes to allow for quicker takeoffs, and slower landings. A computer-based aircraft model of the flaps of an aircraft was developed using the Python based open-source framework OpenMDAO. OpenMDAO is used to develop multi-disciplinary aircraft models using gradient-based optimization; design optimization (MDO) is concerned with solving design problems involving numerical models of complex engineering systems. There were 4 components in the model; each has input values, output variables, and equations to calculate said outputs. The variables and equations are sourced from NASA Fortran code from the 1970s, in a project called the General Aviation Synthesis Program (GASP). These variables and equations which create the model are being converted to Python for ease of use. The flaps model developed will be integrated into a larger model of a conventional aircraft’s flight phases. All subsystems of the model will first be built using the parameters of a Boeing 737 MAX-8, to validate its functionality and accuracy. Then, the aircraft model will be used for hybrid-electric research; running optimizations to improve efficiency, minimize fuel burn, and advance hybrid-electric technology in the aerospace field.

Computer-based aircraft modeling↗
NASA NTRSDate not supplied

Study of Trailing Edge Mini Flaps Interactions on a Wind Tunnel Scale Aspect Ratio 13.5 Common Research Model

This paper presents a computation study of an aspect ratio 13.5 wind tunnel scale Common Research Model (CRM) with trailing edge mini-flaps. A vortex-lattice model of the CRM is developed with transonic small disturbance and integral boundary-layer corrections coupled with NASTRAN equivalent beam model for the rapid CRM aeroelastic simulation. The simulations are performed with individual trailing edge mini-flap deflected and a series of groups of two adjacent trailing edge mini-flaps deflected at the same time. A surrogate model is developed to estimate the aerodynamic interactions between the flaps. To validate the surrogate model, static aeroelastic simulations are performed using FUN3D CFD solver.

Interaction↗
NASA NTRS1972

Externally-blown-flap noise

Noise data were obtained with a large externally blown flap model. A fan-jet engine exhaust was simulated by a 1/2-scale bypass nozzle supplied by pressurized air. The nozzle was pylon mounted on a wing section having a double-slotted flap for lift augmentation. Noise radiation patterns and spectra were obtained for nozzle exhaust velocities between 400 and 1150 ft/sec. The blown flap noise data are in good agreement with previous small model results extrapolated to test conditions by Strouhal scaling. The results indicate that blown flap noise must be suppressed to meet STOL aircraft noise goals.

Dorsch, R. G.↗
NASA NTRS1972

Aeroacoustic characteristics of jet flap type exhausts.

This work which is intended to shed more light on the acoustic and fluid dynamic characteristics of jet flap type exhaust flows, reports and discusses some typical experimental results obtained with cold model air jets in a reverberation chamber. Acoustic data on the total sound power output and the overall noise spectrum of various jet flap configurations are given and compared with data from conventional circular jets. In addition various flow data for the same jets resulting from hot wire measurements are reported and general conclusions are obtained regarding the expected noise source distribution. The results indicate the dependence of the acoustic and flow characteristics on the major nozzle parameters. For the jet flaps the total radiated sound power is found to follow a 3 to 6 power of the exhaust velocity while for the circular jets the 8 power law is confirmed. The noise produced in the secondary mixing region downstream of the flap trailing edge tends to exceed the noise issuing from the primary mixing region.

Gruschka, H. D.↗
NASA NTRS1972

Externally-blown-flap noise.

Noise data were obtained with a large externally blown flap model. A fan-jet engine exhaust was simulated by a 1/2-scale bypass nozzle supplied by pressurized air. The nozzle was pylon mounted on a wing section having a double-slotted flap for lift augmentation. Noise radiation patterns and spectra were obtained for nozzle exhaust velocities between 400 and 1150 ft/sec. The blown flap noise data are in good agreement with previous small model results extrapolated to test conditions by Strouhal scaling. The results indicate that blown flap noise must be suppressed to meet STOL aircraft noise goals.

Dorsch, R. G.↗
NASA NTRS1973

Flex flap

To provide flap with large upper surface radius as required for airplanes with over-the-wing blowing, distort upper surface of flap by actuator. Flap can be used as control surface at leading as well as trailing edges and, with minor modification, as variant of Jacobs-Hurkamp air flap.

Currey, N. S.↗