Search NASA⌕ Search

SEARCH · Search NASA

Results for “frequency shift”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Analyzing Mechanical integrity of Microwave resonant Cavity flowmeter

The microwave resonant cavity flow sensor has been proposed to address the difficulties of measuring high-temperature molten salt flow in reactor vessels. The flow sensor consists of a metallic cylindrical cavity coupled to a microwave waveguide. The cylindrical cavity has one of the flat surfaces thin enough to undergo microscopic deflection due to dynamic pressure of the exerted by the flowing fluid. Deflection of the membrane causes a shift in the microwave resonant frequency. Fluid velocity can be estimated from the calibration curve. The objective of this report is to investigate mechanical integrity of the flowmeter’s membrane. The membrane is a thin stainless-steel circular plate with a clamped edge, subjected to uniform load. By calculating the stress on the plate due to deflection and, comparing the stress to the material ultimate tensile strength and yield strength, it can be estimated if the plate will fail. If the maximum stress is greater than the yield strength, the plate will undergo plastic deformation, and the sensor will be disabled. A stress greater than the ultimate tensile strength will cause the plate to fracture. The stress on the plate was calculated with an analytic closed form solution model, and with COMSOL Structural Mechanics Module which does not involve any approximations. Stresses in both the analytic model and COMSOL numerical model were calculated for stainless steel 316 thin circular plates under room temperature conditions, where the fluid is water. The diameter of the circular plate is approximately one inch, and thickness is 10mil. Fluid flow velocity is in the range from 0.5m/s to 1m/s. The results from the two models are similar. Both the analytic model and COMSOL model showed that maximum stresses on the plate, which are at the radial boundary of the plate, are three orders of magnitude smaller than the yield strength and ultimate tensile strength. This indicates that the sensor is at a low risk of mechanical failure.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

Third Annual Report on Development of Microwave Resonant Cavity Transducer for Fluid Flow Sensing

We are investigating a microwave resonant cavity transducer for flow sensing in the vessel of a high temperature fluid advanced reactor (AR), such as a molten salt cooled reactor (MSCR) or a sodium fast reactor (SFR). This transducer is a hollow metallic cylindrical cavity, with one of the flat walls of the cylinder flexible enough to undergo microscopic deflection due to dynamic fluid pressure. Membrane deflection leads to a shift in the microwave resonant frequency, which can be detected with a spectrum analyzer.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Impact of prescribed fire on soil microbial communities in a Southern Appalachian Forest clear-cut

Escalating wildfire frequency and severity, exacerbated by shifting climate patterns, pose significant ecological and economic challenges. Prescribed burns, a common forest management tool, aim to mitigate wildfire risks and protect biodiversity. Nevertheless, understanding the impact of prescribed burns on soil and microbial communities in temperate mixed forests, considering temporal dynamics and slash fuel types, remains crucial. Our study, conducted at the University of Tennessee Forest Resources AgResearch and Education Center in Oak Ridge, TN, employed controlled burns across various treatments, and the findings indicate that low-intensity prescribed burns have none or minimal short-term effects on soil parameters but may alter soil nutrient concentrations, as evidenced by significant changes in porewater acetate, formate, and nitrate concentrations. These burns also induce shifts in microbial community structure and diversity, with Proteobacteria and Acidobacteria increasing significantly post-fire, possibly aiding soil recovery. In contrast, Verrucomicrobia showed a notable decrease over time, and other specific microbial taxa correlated with soil pH, porewater nitrate, ammonium , and phosphate concentrations. Our research contributes to understanding the intricate relationships between prescribed fire, soil dynamics, and microbial responses in temperate mixed forests in the Southern Appalachian Region, which is valuable for informed land management practices in the face of evolving environmental challenges.

Microbiology↗
DOE OSTI2020

Thermal Frequency Drift of 3D Printed Microwave Components

Fabrication of microwave slot array antennas and waveguide bandpass and notch filters using 3D printing has significant advantages in terms of speed and cost even for parts with high mechanical complexity. One disadvantage of Stereolithography (SLA) 3D printed, copper plated microwave components is that some SLA resins have a high Coefficient of Thermal Expansion (CTE), quoted in micrometers per meter per degree or 10 -6 per degree. Compared to typically used metals such as aluminum (CTE 24 × 10 -6 ·K -1 ) and copper (CTE 17 × 10 -6 ·K -1 ), SLA resin can have CTE above 100 × 10 -6 ·K -1 . Resonant structures experience significant frequency drift with temperature changes on the order of 10–50 °C. The issue of 3D printed microwave structures changing frequency characteristics significantly with temperature shift has not been addressed or reviewed in current literature. We measured and simulated the effect of temperature change on a slot array, cavity notch filters, and post loaded waveguide bandpass filters. We tested several types of SLA resin, different plating techniques, and also Direct Metal Laser Sintering (DMLS) and Binder Infusion metal 3D printing. Performance as a function of temperature is presented for these alternatives.

three-dimensional printing↗
DOE OSTI2022

Superconducting Shuttle-Flux Shift Register for Race Logic and Its Applications

Here this paper presents a superconducting, magnetically-coupled, shuttle-flux shift register (SF-SR) that stores single flux quantum (SFQ) pulses. This shift register has a DC bias operating margin of ±34% at 10 GHz, with a power dissipation of 3.6 μW and 38% fewer Josephson junctions (JJs) when scaled up to multiple stages compared to a data flip-flop (DFF) based shift register. The clock input is inductively coupled and is independent from the data input. We then present three applications for our SF-SR. In the first application, we add two non-destructive readout (NDRO) cells to construct a buffer that temporarily stores the temporal information of a series of race logic (RL) pulses. The second application is a pseudo-random number generator based on a linear function shift register (LFSR). The third application is N parallel SF-SRs that can act similar to a deserializer or instead can emulate a single SF-SR of N times higher clock frequency. These three applications motivate deep shift registers with many shifting intervals, which our SF-SR can implement with fewer JJs and lower power consumption compared to DFF-based shift registers.

42 ENGINEERING↗
DOE OSTI2020

NMR studies of the ground states of Ni 50-x Co x Mn 35 In 15 (x=1, 2.5) and Ni 45 Co 5 Mn 37 In 13 Heusler alloys

Three temperature-induced phase transitions at T=T 1 , T M /T A , and T C , related to the ferromagnetic order of the martensitic phase (FMMP), martensitic (structural) transitions (MT), and the ferromagnetic order of the austenitic phase (FMAP), respectively, have been observed in the off-stoichiometric Heusler alloys, Ni 50-x Co x Mn 35 In 15 (x=1, 2.5) and Ni 45 Co 5 Mn 37 In 13 . In this work, the phase transitions temperatures are found to be depended on alloy composition. A kinetic arrest of the AP was observed for Ni 47.5 Co 2.5 Mn 35 In 15 in the magnetization measurements during field-cooling cycle (FCC) at 50 kOe. Depending upon the cooling protocols, ZFC and FCC (at H = 50 kOe), two different ground states of the alloys can be found in Ni 47.5 Co 2.5 Mn 35 In 15 and Ni 45 Co 5 Mn 37 In 13 alloys. The ground states (T=4.2 K and external field H=0) of the alloys was found to be characterized by three main line: two, partially overlapping, at higher frequencies (300-450 MHz), most likely corresponding of manganese resonance lines and one at lower frequency at about 200 MHz. A significant shift in the spectrum of Ni 45 Co 5 Mn 37 In 13 by about 100 MHz to higher frequencies was observed. The correlation of magnetizations obtained from magnetic moment and NMR studies is discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Crucial role of thermal fluctuations and vertex corrections for the magnetic pseudogap

It is generally believed that in a two-dimensional metal, whose ground state is antiferromagnetically ordered with Q = (π,π), thermal (static) magnetic fluctuations give rise to precursor behavior above TN in which the spectral function of a hot fermion (the one for which k and k + Q are Fermi surface points) contains two peaks, separated by roughly the same energy as in the antiferromagnetically ordered state. The two peaks persist in some range of T > T N and eventually merge into a single peak at zero frequency. This behavior is obtained theoretically by departing from free fermions in a paramagnet and evaluating the dressed fermionic Green's function by summing up infinite series of diagrams with contributions from thermal magnetic fluctuations. We show, following that keeping vertex renormalization diagrams in these series is crucial as other terms only broaden the spectral function of a hot fermion but do not shift its maximum away from zero frequency. As the consequence, the magnetic pseudogap should be treated as an input for theories that neglect vertex corrections, such as, e.g., Eliashberg theory for magnetically mediated superconductivity. We also analyze the potential pseudogap behavior at T = 0. Here, we argue that it may exist, but only at a finite correlation length, and not as a precursor to antiferromagnetism.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Long range frequency chirping of Alfvén eigenmodes

In this work, a theoretical framework has been developed for an NBI scenario to model the hard non-linear evolution of global Alfvén eigenmodes (GAEs) where the adiabatic motion of phase-space structures (holes and clumps), associated with frequency chirping, occurs in generalized phase-space of slowing down energetic particles. The radial profile of the GAE is expanded using finite elements, which allows an update of the mode structure as the mode frequency chirps. Constants of motion are introduced to track the dynamics of energetic particles during frequency chirping by implementing proper action-angle variables and canonical transformations which reduce the dynamics essentially to 1D. Consequently, we specify whether the particles are drifting inward/outward as the frequency deviates from the initial MHD eigenfrequency. Using the principle of least action, we have derived the non-linear equation describing the evolution of the radial profile by varying the total Lagrangian of the system with respect to the weights of the finite elements. For the choice of parameters in this work, it is shown that the peak of the radial profile is shifted and also broadens due to frequency chirping. The time rate of frequency change is also calculated using the energy balance and we show that the adiabatic condition remains valid once it is satisfied. This model clearly illustrates the theoretical treatment to study the long-range adiabatic frequency sweeping events observed for Alfvén gap modes in real experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Frequency reproducibility of solid-state thorium-229 nuclear clocks

Solid-state thorium-229 ( 229 Th) nuclear clocks are set to provide new opportunities for precision metrology and fundamental physics. Taking advantage of inherent low sensitivity of a nuclear transition to its environment, orders of magnitude more emitters can be hosted in a solid-state crystal compared with current optical lattice atomic clocks. Furthermore, solid-state systems needing only simple thermal control are key to the development of field-deployable compact clocks. Here we explore and characterize the frequency reproducibility of the 229 Th:CaF 2 nuclear clock transition, a key performance metric for all clocks. We measure the transition linewidth and centre frequency as a function of the doping concentration, temperature and time. We report the concentration-dependent inhomogeneous linewidth of the nuclear transition, limited by the intrinsic host crystal properties. We determine an optimal working temperature for the 229 Th:CaF 2 nuclear clock at 196(5) K, at which the first-order thermal sensitivity vanishes. This would enable in situ temperature co-sensing using different quadrupole-split lines, reducing the temperature-induced systematic shift below the 10 −18 fractional frequency uncertainty level. At 195 K, the reproducibility of the nuclear transition frequency is 220 Hz (fractionally 1.1 × 10 −13 ) for two differently doped 229 Th:CaF 2 crystals over 7 months. Furthermore, these results form the foundation for understanding, controlling and harnessing the coherent nuclear excitation of 229 Th in solid-state hosts and for their applications in constraining temporal variations of fundamental constants.

Atomic and molecular physics↗
DOE OSTI2025

Shafranov-shift destabilization of ballooning-type micro-instabilities

Contrary to common wisdom, we argue that the Shafranov shift is destabilizing for the ambient ballooning-type instabilities, which account for most of the transport flux in tokamak core plasmas. Higher Shafranov shift indeed reduces the magnetic drift frequency ω d , i.e. improves the bad curvature mildly, around the outboard midplane. However, this improvement is limited to a very narrow spatial region while ω d is increased over the remaining poloidal space. The eigenfunction averaged $\langle$ω d $\rangle$ is effectively enhanced due to the finite mode width of the eigenfunction and is thus destabilizing to the ballooning-type mode, as demonstrated by gyrokinetic simulations with the CGYRO code using local Miller equilibrium geometry. The predicted nonlinear flux also increases with Shafranov shift, consistent with linear simulations. The reduced transport model TGLF can capture the physics reasonably well.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Precision gyroscope from the helicity of light

We describe a gyroscope that measures rotation based on the effects of the rotation on the polarization of light. Rotation induces a differential phase shift in the propagation of left- and right-circularly polarized light and this phase shift can be measured in suitably designed interferometric setups. The signal in this setup is independent of the frequency of light, unlike various sources of noise such as vibrations, which cause phase shifts that depend on the frequency. Such vibrations are the practical limit on the sensitivity of conventional Sagnac-style optical interferometers that are typically used as gyroscopes. In the proposed setup, one can potentially mitigate this source of noise by simultaneously using two (or more) sources of light that have different frequencies. The signal in this setup scales with the total storage time of the light. Due to its frequency independence, it is thus most optimal to measure the signal using superconducting radio-frequency systems where the high finesse of the available cavities enables considerably longer storage times than is possible in an optical setup.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Quantum optimal control of ten-level nuclear spin qudits in Sr 87

We study the ability to implement unitary maps on states of the I = 9 / 2 nuclear spin in Sr 87 , a d = 10 dimensional (qudecimal) Hilbert space, using quantum optimal control. Through a combination of nuclear spin resonance and a tensor ac Stark shift, by solely modulating the phase of a radio-frequency magnetic field, the system is quantum controllable. Alkaline-earth-metal atoms, such as Sr 87 , have a very favorable figure of merit for such control due to narrow intercombination lines and the large hyperfine splitting in the excited states. We numerically study the quantum speed limit, optimal parameters, and the fidelity of arbitrary state preparation and full SU(10) maps, including the presence of decoherence due to optical pumping induced by the light-shifting laser. We also study the use of robust control to mitigate some dephasing due to inhomogeneities in the light shift. We find that with an rf Rabi frequency of Ω rf and 0.5% inhomogeneity in the the light shift we can prepare an arbitrary Haar-random state in a time T = 4.5 π / Ω rf with average fidelity ( F ψ ) = 0.9992 , and an arbitrary Haar-random SU(10) map in a time T = 24 π / Ω rf with average fidelity ( F U ) = 0.9923 .

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2025

Rising atmospheric moisture escalates the future impact of atmospheric rivers in the Antarctic climate system

Abstract Despite their relative rarity, atmospheric rivers are key contributors to the surface mass balance of Antarctica. However, the future role of atmospheric rivers in modulating Antarctic sea-level contributions is a major area of uncertainty. Here, we leverage high-resolution climate simulations to show that Antarctic atmospheric rivers are highly sensitive to future increases in atmospheric moisture, leading to a doubling of atmospheric river frequencies and 2.5 × increase in precipitation from 2066–2100 under present-day thresholds for atmospheric river detection. However, future precipitation impacts are critically dependent on the detection threshold: accounting for moisture increases in the threshold produces smaller, regional changes in atmospheric river frequency, primarily resulting from an eastward shift in the polar jet maximum wind speeds. Our results underscore the importance of using large ensembles to quantify Antarctic atmospheric river responses to variability in projected moisture, which may not be captured when using only a few ensemble members.

Environmental Sciences & Ecology↗
DOE OSTI2024

Extracting and Interpreting Electrochemical Impedance Spectra (EIS) from Physics-Based Models of Lithium-Ion Batteries

This paper implements a highly efficient algorithm to extract electrochemical impedance spectra (EIS) from physics-based battery models (e.g., a P2D model). The mathematical approach is different from how EIS is practiced experimentally. Experimentally, the voltage (current) is harmonically perturbed over a wide range of frequencies and the amplitude and phase shift of the corresponding current (voltage) is measured. The experimental approach can be implemented in simulation software, but is computationally expensive. The approach here is to determine locally linear state-space models from the full physical model. The four Jacobian matrices that are the basis of the state-space models can be derived by numerical differentiation of the physical model. The EIS is then extracted from the state-space model using computationally efficient matrix-manipulation techniques. The algorithm can evaluate the full EIS at an instant in time during a transient, independent of whether the battery is in a stationary state. The approach is also able to separate the full-cell impedance to evaluate partial EIS, such as for a battery anode alone. Although such partial EIS is difficult to measure experimentally, the partial EIS provides valuable insights in interpreting the full-cell EIS.

25 ENERGY STORAGE↗
DOE OSTI2023

Observed changes in hydroclimate attributed to human forcing

Observational and modeling studies indicate significant changes in the global hydroclimate in the twentieth and early twenty-first centuries due to anthropogenic climate change. In this review, we analyze the recent literature on the observed changes in hydroclimate attributable to anthropogenic forcing, the physical and biological mechanisms underlying those changes, and the advantages and limitations of current detection and attribution methods. Changes in the magnitude and spatial patterns of precipitation minus evaporation (P–E) are consistent with increased water vapor content driven by higher temperatures. While thermodynamics explains most of the observed changes, the contribution of dynamics is not yet well constrained, especially at regional and local scales, due to limitations in observations and climate models. Anthropogenic climate change has also increased the severity and likelihood of contemporaneous droughts in southwestern North America, southwestern South America, the Mediterranean, and the Caribbean. An increased frequency of extreme precipitation events and shifts in phenology has also been attributed to anthropogenic climate change. While considerable uncertainties persist on the role of plant physiology in modulating hydroclimate and vice versa, emerging evidence indicates that increased canopy water demand and longer growing seasons negate the water-saving effects from increased water-use efficiency.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

The Relationship Between Different VSAR Doppler Resolutions

It is often useful to think of the Doppler resolution of a vertical synthetic aperture radar in terms of the distance spanned by a resolution cell on the ground in unit meters, yet Doppler shift is fundamentally a measure of frequency, so there is a disconnect. This memo derives relationships between frequently invoked Doppler resolution expressions when they are expressed in ground-projected units (meters), angular units (radians), range-rate units (meters/second), and frequency units (Hertz).

47 OTHER INSTRUMENTATION↗
DOE OSTI2025

Multi-physics Topology OPtimization and Additive Manufacturing for High-temperature Heat Exchangers

This research significantly advances the understanding of high-temperature heat exchanger design through an integrated approach that combines topology optimization (TO), triply periodic minimal surface (TPMS) structures, additive manufacturing (AM) and thermohydraulic testing. Each of these components contributes uniquely to a unified, high-performance design, fabrication and testing workflow. Topology optimization serves as the foundation of the design methodology by providing a systematic way to determine the most effective material layout for separating hot and cold fluids while maximizing thermal performance. The researchers introduced a novel three-material optimization framework using two density fields to represent hot fluid, cold fluid, and solid domains. This approach enables automated discovery of optimal shapes and flow paths that cannot be intuitively designed, especially under constraints imposed by manufacturing technologies. Furthermore, constraints such as minimal wall thickness and overhang angles were embedded into the optimization process, ensuring that resulting designs are not only thermally efficient but also manufacturable using modern additive techniques. In parallel, the study delves into the use of Gyroid-based TPMS geometries for constructing the core of the heat exchanger. TPMS structures are known for their high surface area, excellent fluid mixing capabilities, and minimal pressure drop characteristics. The researchers applied a data-driven modeling framework using Heteroscedastic Sparse Gaussian Process Regression (HSGPR) combined with genetic algorithms. This allowed for the rapid evaluation and optimization of key geometric parameters such as frequency, iso-value, and phase shift. The result was a set of Gyroid structures tailored for high heat transfer and low flow resistance, demonstrating clear improvements over conventional straight-channel designs. After the designing process, additive manufacturing played a critical role by turning these highly complex, optimized geometries into physical components. Utilizing Laser Powder Bed Fusion (LPBF) with Haynes 282, the study demonstrated the feasibility of fabricating these heat exchangers at high precision. Post-processing methods, including dilation-erosion operations, were applied to ensure local features adhered to self-supporting constraints. The fabricated structures were then subjected to thermohydraulic testing under conditions representative of supercritical CO 2 Brayton cycles, validating the predicted performance and confirming the viability of the full design-to-fabrication pipeline. Finally, thermohydraulic testing across the above studies served as a crucial experimental validation of advanced heat exchanger. Under consistent high-temperature and high-pressure conditions using supercritical CO 2 , the testing demonstrated that both TO and Gyroid-based TPMS designs significantly outperformed conventional straight-channel HXs. The TO design achieved a 115% increase in UA and NTU and a 27.6% boost in gravimetric power density, while the data-driven optimized Gyroid design delivered a 166% increase in UA and NTU and improved effectiveness from 68.7% to 86.1%. These results validate the simulation models, confirm the manufacturability of complex geometries under AM constraints, and provide key insights into design-performance trade-offs, thereby advancing the development of high-efficiency, compact heat exchangers for extreme environments.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Optimizing Magnetic Force Microscopy Resolution and Sensitivity to Visualize Nanoscale Magnetic Domains

Magnetic force microscopy (MFM) enables mapping local magnetic fields across a sample surface with nanoscale resolution. To perform MFM, an atomic force microscopy (AFM) probe whose tip has been magnetized vertically (i.e., perpendicular to the probe cantilever) is oscillated at a fixed height above the sample surface. The resultant shifts in the oscillation phase or frequency, which are proportional to the magnitude and sign of the vertical magnetic force gradient at each pixel location, are then tracked and mapped. Although the spatial resolution and sensitivity of the technique increases with decreasing lift height above the surface, this seemingly straightforward path to improved MFM images is complicated by considerations such as minimizing topographical artifacts due to shorter range van der Waals forces, increasing the oscillation amplitude to further improve sensitivity, and the presence of surface contaminants (in particular water due to humidity under ambient conditions). In addition, due to the orientation of the probe's magnetic dipole moment, MFM is intrinsically more sensitive to samples with an out-of-plane magnetization vector. Here, high-resolution topographical and magnetic phase images of single and bicomponent nanomagnet artificial spin-ice (ASI) arrays obtained in an inert (argon) atmosphere glovebox with <0.1 ppm O 2 and H 2 O are reported. Further, optimization of lift height and drive amplitude for high resolution and sensitivity while simultaneously avoiding the introduction of topographical artifacts is discussed, and detection of the stray magnetic fields emanating from either end of the nanoscale bar magnets (~250 nm long and <100 nm wide) aligned in the plane of the ASI sample surface is shown. Likewise, using the example of a Ni-Mn-Ga magnetic shape memory alloy (MSMA), MFM is demonstrated in an inert atmosphere with magnetic phase sensitivity capable of resolving a series of adjacent magnetic domains each ~200 nm wide.

47 OTHER INSTRUMENTATION↗