Results for “joining” — Page 17

NASA NTRS2007

Fabrication and Characterization of Diffusion Bonds for Silicon Carbide

Diffusion bonds of silicon carbide (SiC) were fabricated using several different types of titanium (Ti) based interlayers between the SiC substrates. The interlayers were an alloyed Ti foil, a pure Ti foil, and a physically vapor deposited (PVD) Ti coating. Microscopy was conducted to evaluate the cross-sections of the resulting bonds. Microprobe analysis identified reaction formed phases in the diffusion bonded region. Uniform and well adhered bonds were formed between the SiC substrates. In the case where the alloyed Ti foil or a thick Ti coating (i.e. 20 micron) was used as the interlayer, microcracks and several phases were present in the diffusion bonds. When a thinner interlayer was used (i.e. 10 micron PVD Ti), no microcracks were observed and only two reaction formed phases were present. The two phases were preferred and fully reacted phases that did not introduce thermal stresses or microcracks during the cool-down stage after processing. Diffusion bonded samples were evaluated with the non-destructive evaluation (NDE) methods of pulsed thermography and immersion ultrasonic testing. Joined SiC substrates that were fully bonded and that had simulated bond flaws in the interlayer were also evaluated using immersion ultrasound. Pull testing was conducted on the bonds to determine the tensile strength. To demonstrate the joining approach for a complex multilayered component for a low NOx injector application, the diffusion bonding approach was used to join three 4" diameter SiC discs that contained complex fuel and air flow channels.

Halbig, Michael↗

NASA NTRS2009

Spacecraft Station-Keeping Trajectory and Mission Design Tools

Two tools were developed for designing station-keeping trajectories and estimating delta-v requirements for designing missions to a small body such as a comet or asteroid. This innovation uses NPOPT, a non-sparse, general-purpose sequential quadratic programming (SQP) optimizer and the Two-Level Differential Corrector (T-LDC) in LTool (Libration point mission design Tool) to design three kinds of station-keeping scripts: vertical hovering, horizontal hovering, and orbiting. The T-LDC is used to differentially correct several trajectory legs that join hovering points. In a vertical hovering, the maximum and minimum range points must be connected smoothly while maintaining the spacecrafts range from a small body, all within the law of gravity and the solar radiation pressure. The same is true for a horizontal hover. A PatchPoint is an LTool class that denotes a space-time event with some extra information for differential correction, including a set of constraints to be satisfied by T-LDC. Given a set of PatchPoints, each with its own constraint, the T-LDC differentially corrects the entire trajectory by connecting each trajectory leg joined by PatchPoints while satisfying all specified constraints at the same time. Vertical and horizontal hover both are needed to minimize delta-v spent for station keeping. A Python I/F to NPOPT has been written to be used from an LTool script. In vertical hovering, the spacecraft stays along the line joining the Sun and a small body. An instantaneous delta-v toward the anti- Sun direction is applied at the closest approach to the small body for station keeping. For example, the spacecraft hovers between the minimum range (2 km) point and the maximum range (2.5 km) point from the asteroid 1989ML. Horizontal hovering buys more time for a spacecraft to recover if, for any reason, a planned thrust fails, by returning almost to the initial position after some time later via a near elliptical orbit around the small body. The mapping or staging orbit may be similarly generated using T-LDC with a set of constraints. Some delta-v tables are generated for several different asteroid masses.

Chung, Min-Kun J.↗

NASA NTRS2010

Braze Development of Graphite Fiber for Use in Phase Change Material Heat Sinks

Hamilton Sundstrand (HS), together with NASA Johnson Space Center, developed methods to metallurgically join graphite fiber to aluminum. The goal of the effort was to demonstrate improved thermal conductance, tensile strength and manufacturability compared to existing epoxy bonded techniques. These improvements have the potential to increase the performance and robustness of phase change material heat sinks that use graphite fibers as an interstitial material. Initial work focused on evaluating joining techniques from 4 suppliers, each consisting of a metallization step followed by brazing or soldering of one inch square blocks of Fibercore graphite fiber material to aluminum end sheets. Results matched the strength and thermal conductance of the epoxy bonded control samples, so two suppliers were down-selected for a second round of braze development. The second round of braze samples had up to a 300% increase in strength and up to a 132% increase in thermal conductance over the bonded samples. However, scalability and repeatability proved to be significant hurdles with the metallization approach. An alternative approach was pursued which used nickel and active braze allows to prepare the carbon fibers for joining with aluminum. This approach was repeatable and scalable with improved strength and thermal conductance when compared with epoxy bonding.

Quinn, Gregory↗

NASA NTRS2011

Braze Development of Graphite Fiber for Use in Phase Change Material Heat Sinks

Hamilton Sundstrand (HS), together with NASA Johnson Space Center, developed methods to metallurgically join graphite fiber to aluminum. The goal of the effort was to demonstrate improved thermal conductance, tensile strength and manufacturability compared to existing epoxy bonded techniques. These improvements have the potential to increase the performance and robustness of phase change material heat sinks that use graphite fibers as an interstitial material. Initial work focused on evaluating joining techniques from four suppliers, each consisting of a metallization step followed by brazing or soldering of one inch square blocks of Fibercore graphite fiber material to aluminum end sheets. Results matched the strength and thermal conductance of the epoxy bonded control samples, so two suppliers were down-selected for a second round of braze development. The second round of braze samples had up to a 300% increase in strength and up to a 132% increase in thermal conductance over the bonded samples. However, scalability and repeatability proved to be significant hurdles with the metallization approach. An alternative approach was pursued which used a nickel braze allow to prepare the carbon fibers for joining with aluminum. Initial results on sample blocks indicate that this approach should be repeatable and scalable with good strength and thermal conductance when compared with epoxy bonding.

Quinn, Gregory↗

NASA NTRS2012

Gas Shielding Technology for Welding and Brazing

Welding is a common method that allows two metallic materials to be joined together with high structural integrity. When joints need to be leak-tight, light-weight, or free of contaminant-trapping seams or surface asperities, welding tends to be specified. There are many welding techniques, each with its own advantages and disadvantages. Some of these techniques include Forge Welding, Gas Tungsten Arc Welding, Friction Stir Welding, and Laser Beam Welding to name a few. Whichever technique is used, the objective is a structural joint that meets the requirements of a particular component or assembly. A key practice in producing quality welds is the use of shielding gas. This article discusses various weld techniques, quality of the welds, and importance of shielding gas in each of those techniques. Metallic bonds, or joints, are produced when metals are put into intimate contact. In the solid-state "blacksmith welding" process, now called Forge Welding (FOW), the site to be joined is pounded into intimate contact. The surfaces to be joined usually need to be heated to make it easier to deform the metal. The surfaces are sprinkled with a flux to melt surface oxides and given a concave shape so that surface contamination can be squeezed out of the joint as the surfaces are pounded together; otherwise the surface contamination would be trapped in the joint and would weaken the weld. In solid-state welding processes surface oxides or other contamination are typically squeezed out of the joint in "flash."

Nunes, Arthur J.↗

NASA NTRS2014

Simulations of DSB Yields and Radiation-induced Chromosomal Aberrations in Human Cells Based on the Stochastic Track Structure Induced by HZE Particles

The formation of double‐strand breaks (DSBs) and chromosomal aberrations (CAs) is of great importance in radiation research and, specifically, in space applications. We are presenting a new particle track and DNA damage model, in which the particle stochastic track structure is combined with the random walk (RW) structure of chromosomes in a cell nucleus. The motivation for this effort stems from the fact that the model with the RW chromosomes, NASARTI (NASA radiation track image) previously relied on amorphous track structure, while the stochastic track structure model RITRACKS (Relativistic Ion Tracks) was focused on more microscopic targets than the entire genome. We have combined chromosomes simulated by RWs with stochastic track structure, which uses nanoscopic dose calculations performed with the Monte‐Carlo simulation by RITRACKS in a voxelized space. The new simulations produce the number of DSBs as function of dose and particle fluence for high‐energy particles, including iron, carbon and protons, using voxels of 20 nm dimension. The combined model also calculates yields of radiation‐induced CAs and unrejoined chromosome breaks in normal and repair deficient cells. The joined computational model is calibrated using the relative frequencies and distributions of chromosomal aberrations reported in the literature. The model considers fractionated deposition of energy to approximate dose rates of the space flight environment. The joined model also predicts of the yields and sizes of translocations, dicentrics, rings, and more complex‐type aberrations formed in the G0/G1 cell cycle phase during the first cell division after irradiation. We found that the main advantage of the joined model is our ability to simulate small doses: 0.05‐0.5 Gy. At such low doses, the stochastic track structure proved to be indispensable, as the action of individual delta‐rays becomes more important.

Ponomarev, Artem↗

NASA NTRS2014

Simulations of DSB Yields and Radiation-induced Chromosomal Aberrations in Human Cells Based on the Stochastic Track Structure iIduced by HZE Particles

The formation of double‐strand breaks (DSBs) and chromosomal aberrations (CAs) is of great importance in radiation research and, specifically, in space applications. We are presenting a new particle track and DNA damage model, in which the particle stochastic track structure is combined with the random walk (RW) structure of chromosomes in a cell nucleus. The motivation for this effort stems from the fact that the model with the RW chromosomes, NASARTI (NASA radiation track image) previously relied on amorphous track structure, while the stochastic track structure model RITRACKS (Relativistic Ion Tracks) was focused on more microscopic targets than the entire genome. We have combined chromosomes simulated by RWs with stochastic track structure, which uses nanoscopic dose calculations performed with the Monte‐Carlo simulation by RITRACKS in a voxelized space. The new simulations produce the number of DSBs as function of dose and particle fluence for high‐energy particles, including iron, carbon and protons, using voxels of 20 nm dimension. The combined model also calculates yields of radiation‐induced CAs and unrejoined chromosome breaks in normal and repair deficient cells. The joined computational model is calibrated using the relative frequencies and distributions of chromosomal aberrations reported in the literature. The model considers fractionated deposition of energy to approximate dose rates of the space flight environment. The joined model also predicts of the yields and sizes of translocations, dicentrics, rings, and more complex‐type aberrations formed in the G0/G1 cell cycle phase during the first cell division after irradiation. We found that the main advantage of the joined model is our ability to simulate small doses: 0.05‐0.5 Gy. At such low doses, the stochastic track structure proved to be indispensable, as the action of individual delta‐rays becomes more important.

Ponomarev, Artem↗

NASA NTRS2019

Reliable Bonding of Composite Laminates Using Reflowable Epoxy Resins

Epoxy matrix composites assembled with adhesives maximize the performance of aerospace structures, but the possibility of forming weak bonds requires the installation of redundant fasteners, which add weight and manufacturing cost. Co-cured joints (e.g. unitized composite structures) are immune to weak bonds because the uncured resin undergoes diffusion and mixing through the joint. A means of co-curing complex structures may reduce the need for redundant fasteners in bondlines. To this end, NASA started the AERoBOND project to develop novel joining materials to enable a “secondary-co-cure” assembly process. Aerospace epoxy resin systems reformulated with offset stoichiometry prevented the resin from advancing beyond the gel point during a conventional autoclave cure cycle up to 180 °C. The offset resins were applied to the joining surfaces of laminate preforms as prepreg. Two surfaces with complimentary offset resins were joined using conventional secondary bonding techniques. Preliminary efforts have indicated that the resulting joint has no discernable interface and appears as a conventional co-cured laminate under optical magnification. This report will discuss the initial work performed regarding formulation of the epoxy resin system using calorimetry, rheology, and mechanical testing.

Palmieri, Frank L.↗

NASA NTRSDate not supplied

Test Results for Autonomous Assembly of Modular Space Structures

This paper presents test results for autonomous assembly of a modular space structure. A Universal Robots UR10e manipulator with a custom end-effector, known as the Grapple Tool, was used to join TriTruss structural modules. The TriTrusses and their assembly configuration were developed for an in-space assembled telescope conceptual design. The tests presented here were performed with a 1:2.8 dimensionally scaled version of the Tri-Trusses. Robot trajectories were generated autonomously using a sample-based motion planner and an a-priori worksite model. The test results verify the assembly concept of operations as well as the software requirements for the Grapple Tool. While the Grapple Tool used in the tests was designed for the 1:2.8 scale Tri-Trusses, it has the same actuators, software, and computation architecture as the version designed for the full scale structure. The test operations consist of picking up two TriTrusses from their stowed locations and joining them to a third TriTruss mounted on a test stand and joining them to each other. This constitutes the first three modules of the in-space assembled telescope conceptual design. The paper presents the robot behavioral architecture, the generated trajectories commanded, the actual trajectories of the robot, and actuator performance of the Grapple Tool.

test↗

NASA NTRSDate not supplied

Test Results for Autonomous Assembly of Modular Space Structures

This paper presents test results for autonomous assembly of a modular space structure. A Universal Robots UR10e manipulator with a custom end-effector, known as the Grapple Tool, was used to join TriTruss structural modules. The TriTrusses and their assembly configuration were developed for an in-space assembled telescope conceptual design. The tests presented here were performed with a 1:2.8 dimensionally scaled version of the Tri-Trusses. Robot trajectories were generated autonomously using a sample-based motion planner and an a-priori worksite model. The test results verify the assembly concept of operations as well as the software requirements for the Grapple Tool. While the Grapple Tool used in the tests was designed for the 1:2.8 scale Tri-Trusses, it has the same actuators, software, and computation architecture as the version designed for the full scale structure. The test operations consist of picking up two TriTrusses from their stowed locations and joining them to a third TriTruss mounted on a test stand and joining them to each other. This constitutes the first three modules of the in-space assembled telescope conceptual design. The paper presents the robot behavioral architecture, the generated trajectories commanded, the actual trajectories of the robot, and actuator performance of the Grapple Tool.

test↗

NASA NTRSDate not supplied

A Combined Computational, Experimental, and Technology Development Approach to In-Space Laser Manufacturing Maturation at NASA Marshall Space Flight Center

In-space manufacturing (ISM) is emerging as a field vital to continued access and capabilities in the space environment. NASA Marshall Space Flight Center (MSFC) is advancing the frontier of in-space laser manufacturing (ISLM) techniques through work initially focused on maturing laser beam welding (LBW) and laser forming (LF) for use in space. Such techniques proffer the ability to assemble and join structures in space from sheet metal or other stock – extant satellites, in situ resource utilization of Lunar regolith, etc. – by forming to desired shapes and then joining via in-space welding (ISW). ISLM processes are useful for assembly, joining, modification, and repair of structures in free space and on the Lunar surface such as large observatories, antennas, trusses, blast/thermal/radiation shields, pressure vessels, and more. However, these techniques are not yet qualified & certified (Q&C) for regular application in space. It would be prohibitively expensive, laborious, and time-consuming to perform Q&C via traditional experimental approaches as data collection & experimentation in space is resource-intensive. As such, benchmark experiments and focused, properly instrumented technology demonstration efforts in space can collect sufficient data that – when combined with verified computational models in an integrated computational materials engineering (ICME) approach – can validate ICME tools capable of translating more readily obtained ground data to in-space, in situ, computationally informed Q&C of ISLM techniques. Several ISLM projects at MSFC are obtaining the data required to validate ICME tools through both ground and flight experiments. A parabolic flight experiment of LBW under vacuum is manifested for August 2024, including both microgravity and Lunar gravity profiles. This collaboration with the Ohio State University is investigating common aerospace alloys such as 316L stainless steel, 2219 aluminum alloy, and Ti64 titanium alloy. In situ data collection includes videography, thermography, and reference thermocouples to build a thermal model of the welds. This will elucidate the relevant physics when combined with post-flight microstructural examination and mechanical testing. MSFC is also progressing towards a suborbital flight experiment of LBW under vacuum, which could provide reams of data on ISW during sustained, high-quality reduced gravity. The effect of combined thermal (cryogenic and high-temperature) and vacuum exposure on both LBW (NASA-funded) and LF (DARPA-funded) is being investigated through ground experiments. In addition to the copious data collected during these ground experiments, ruggedization of LBW hardware will also be pursued. The datasets from these experiments will be used to validate computational models which will inform future ISLM efforts in an ICME framework. A variety of techniques across lengths scales, from CALPHAD-driven thermodynamics & kinetics to phase field modeling of solidification to kinetic Monte Carlo simulations of grain evolution at the mesoscale, will be employed to accelerate the infusion and eventual Q&C of LBW and LF for use in space. The development of data-driven surrogate models to bridge ground to flight experiments and thereby reduce the need for resource-intensive experiments in space will also be investigated. These ICME techniques, surrogate models, and datasets from ground testing can also be employed to advance manufacturing in terrestrial environments.

in-space welding↗

DOE OSTI2026

Low-Pressure Diffusion Bonding of Vanadium to Commercially Pure Titanium and Ti-6Al-4V

Modern technology increasingly requires components to be made from specific high-performance materials. To support complex multi-metal structures, a variety of techniques are required to join dissimilar metal parts with precise shapes. This study evaluates vacuum diffusion bonding as a method for joining titanium and vanadium, focusing on both pure titanium and the common alloy Ti-6Al-4V. We employ modest pressure provided by a weight and simple surface preparation to simulate the most commercially applicable process. Here, we show that Ti-6Al-4V alloy bonds readily to V, forming a continuous, clearly defined interdiffusion layer with predictable kinetics. Conversely, commercially pure Ti forms a crack-prone bond with V that fails to improve at higher bonding temperatures or longer times. We attribute this failure to the concentration of stress caused by the ß-to-α phase transformation in Ti. The contrasting bonding efficacy between pure Ti and the alloy provides insight into the crystallographic interactions that occur at the interface during bonding and cooling. These results provide surprising insight into a new method for bonding Ti alloys to V and possibly other metals that share the body-centered cubic crystal structure.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Effect of die design on microstructure and mechanical joint strength in friction self-piercing riveted AA7055-T76 and AA7055-T76

In the present study, a unique friction self-piercing riveting (F-SPR) was applied to join high-strength, low-ductility aluminum alloy (AA) 7055-T76 and AA7055-T76 to mitigate a cracking issue. Also, the effect of die design on both joint formation and the mechanical joint performance were investigated. A crack-free joint was achieved when joining AA7055-T76 and AA7055-T76 by F-SPR. As the bottom diameter of the die increased, the mechanical interlocking distance initially increased then became almost saturated. At the same time, the solid-state bonding gradually disappeared, and the lap-shear fracture changed from bottom aluminum fracture to rivet pull-out with partial bottom aluminum fracture. The average maximum lap-shear joint strength of 11.57 kN and cross tension of 5.65 kN were achieved from the D2 die design owing to the combined contributions from high mechanical interlocking distance and good solid-state bonding at the joint interface. Ultrafine grain refinement was observed at the region next to the rivet shank outer surface and along the materials flow line between the top and bottom aluminum sheet in the rivet cavity. Further, because of the same joint-process parameters, the hardness profile at the joints made by different dies did not show obvious differences. As the distance from the base metal to the rivet outer surface decreased, frictional heat caused the hardness to initially decrease from 190 to 150 HV in the heat-affected zone. Hardness increased up to 175 HV in the thermomechanical affected zone (TMAZ-I) owing to large plastic deformation.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Suppression of irradiation hardening in tungsten-coated ferritic steel for fusion reactor blanket applications

W-coated reduced activation ferritic steels have been developed for use as plasma facing components in fusion reactor blankets, offering excellent sputtering resistance and structural strength. Previous high-temperature coating methods, such as diffusion bonding and brazing, caused interfacial deterioration due to thermal stress from mismatched thermal expansion between W and reduced activation ferritic steel. To address this, underwater explosive welding was introduced as a high-velocity cold process that joins dissimilar materials while maintaining a strong, thin interface without the thermal issues associated with traditional methods. In this study, the effects of neutron irradiation on the hardness and microstructure in W-coated F82H reduced activation ferritic steel (W/F82H) joined by underwater explosive welding are investigated. Following neutron irradiation at 290 °C, irradiation hardening is suppressed in W, F82H, and their interface within the W/F82H material. Furthermore, microstructural observations indicate that the recovery of work hardening and relaxation of elastic strain introduced during coating significantly contribute to the suppression of irradiation hardening in W/F82H. In conclusion, W/F82H exhibits significantly suppressed irradiation hardening compared with those in stand-alone materials. This suppression is explained by residual stress from thermal expansion mismatch and the unique microstructure at the interface. These results provide valuable insights for the development of more durable materials in nuclear fusion applications.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Bio-inspired interlocking metasurfaces

Interlocking metasurfaces (ILMs) are patterned arrays of mating features that enable the joining of bodies by constraining motion and transmitting force. They offer an alternative to traditional joining solutions such as mechanical fasteners, welds, and adhesives. This study explores the development of bio-inspired ILMs using a problem-driven bioinspired design (BID) framework. We develop a taxonomy of attachment solutions that considers both biological and engineered systems and derive conventional design principles for ILM design. We conceptualize two engineering implementations to demonstrate concept development using the taxonomy and ILM conventional design principle through the BID framework: one for rapidly assembled bridge truss members and another for modular microrobots. These implementations highlight the potential of BID to enhance performance, functionality, and tunability in ILMs.

attachment↗

DOE OSTI2026

Fabrication of ceramic to metal graded structure for high temperature CSP receiver application using solid state additive manufacturing

The overarching goal of this project is to come up with an innovative joining solution for integration of SiC ceramic to structural materials such as stainless steels (SS)/Ni-base alloys, where intimate metallurgical bonding between SiC ceramic and the structural metallic alloy is demonstrated at the interface. Implementation of a simple, yet robust joining method would help in increasing the application space of SiC in a high-temperature CSP (concentrated solar power) plant, especially in the receiver section. This research goal has been achieved by creating a functionally graded material (FGM) interface between SiC and the selected structural material with the help of powder metallurgy (PM) approach and demonstrate intimate metallurgical bonding between monolithic RB-SiC and 316L stainless steel alloy blanks.

36 MATERIALS SCIENCE↗

DOE OSTI2024

The Toughness of Interlocking Metasurfaces

Interlocking metasurfaces (ILMs) are arrays of autogenous latching unit cells patterned across a surface. These create structural joints similar to bioinspired suture joints but patterned over a 2D surface rather than a 1D seam. This enables ILMs to be an alternative to conventional joining technologies such as bolts, welds, and adhesives. However, compared to conventional joining methods, relatively little is known of the engineering considerations for designing structural ILMs. Herein, the interfacial toughness of an archetypal ILM is examined for the first time. Under the conditions studied here, the ILM is substantially tougher than the material from which it is made, in this case, exhibiting up to a 50% increase in interfacial crack initiation energy over the solid base material, a photocured 3D‐printed polymer. Through experimental tests using in‐situ digital image correlation along with complementary computational analyses, the mechanism of toughening in the ILM structure and the origins of toughness anisotropy are revealed. The increase in toughness is associated with cross‐cell interactions, that is, load‐sharing across unit cells, which give rise to a finite process zone length with different effective material properties. In this way, ILM toughening is analogous to crack blunting in ductile materials or fiber bridging in composites; yet here, the ILM is composed of a single‐phase base material and so the architected toughening is geometric in nature and hence amenable to future topological optimization.

fracture↗

DOE OSTI2026

Towards High-Speed friction stir welding of 25 mm Thick AA2139-T8: tool innovation and process development

Joining thick plates (≥ 12 mm) of aluminum (Al) alloys is challenging due to high tool forces, uneven material flow, and non-uniform heat distribution through the material’s thickness. Recent advancements in tool design and welding parameters for friction stir welding (FSW) in thick plates butt joining have encountered a developmental plateau, highlighting the need for innovative approaches to overcome existing limitations. Here, this study focuses on the systematic development of single-pass and double-pass FSW processes for high-strength aluminum alloy AA2139-T8, to improve joint efficiency and enable high-speed welding capabilities. Experimental evidence is presented for a novel tool design with opposing pin threads, enabling high-speed (178 mm/min) single-pass friction stir butt welding of 25 mm thick AA2139-T8. A series of FSW trials was conducted both in air and with a trailing water spray, using steel backing plates (BPs) to investigate the impact of quenching and cooling rates on process response and joint performance. A joint efficiency of 83% was attained using the novel tool features and effectively controlling process forces and thermal boundary conditions.

AA2139-T8↗