SEARCH · Search NASA

Results for “low-pressure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

All sources NASA NTRS DOE OSTI

NASA NTRS1992

FAGE measurements of tropospheric HO with measurements and model of interferences

Ambient HO measurements by low-pressure laser-excited fluorescence with chemical modulation, and supporting ozone and water-vapor data, are presented for periods in May and August 1987. The observed peak daytime ambient HO concentrations are in the range (2.5 to 8) x 10 exp 6 molecules/cu cm and show small negative offsets due to photochemical interference. Direct measurements of the interference at fixed (O3) give the dependence on ambient (H2O) and on the modulating reagent (isobutane). At ambient (O3) = 30 ppb and 10 torr H2O, with excitation and detection at a total pressure of 4 torr, the net interference is equal to (HO) = -1.3 x 10 exp 6 molecules/cu cm. Production of HO by the reaction of isobutane with O(1D) accounts for the negative interference. Quenching of HO fluorescence by the modulating reagent contributes a smaller positive term to the interference; kinetic measurements of the quenching rate coefficient are reported. The experimental interference results are compared with a detailed kinetic model of HO production, excitation, relaxation, and detection; reasonable agreement is found.

Hard, T. M.↗

NASA NTRS1992

Automatic detection of anomalies in Space Shuttle Main Engine turbopumps

A prototype expert system (developed on both PC and Symbolics 3670 lisp machine) for detecting anomalies in turbopump vibration data has been tested with data from ground tests 902-473, 902-501, 902-519, and 904-097 of the Space Shuttle Main Engine (SSME). The expert system has been utilized to analyze vibration data from each of the following SSME components: high-pressure oxidizer turbopump, high-pressure fuel turbopump, low-pressure fuel turbopump, and preburner boost pump. The expert system locates and classifies peaks in the power spectral density of each 0.4-sec window of steady-state data. Peaks representing the fundamental and harmonic frequencies of both shaft rotation and bearing cage rotation are identified by the expert system. Anomalies are then detected on the basis of sequential criteria and two threshold criteria set individually for the amplitude of each of these peaks: a prior threshold used during the first few windows of data in a test, and a posterior threshold used thereafter. In most cases the anomalies detected by the expert system agree with those reported by NASA. The two cases where there is significant disagreement will be further studied and the system design refined accordingly.

Lo, Ching F.↗

NASA NTRS1992

Prospective new transportation application initiatives in NASA's earth-to-orbit propulsion technology program

NASA's Earth-to-Orbit (ETO) Propulsion Technology Program, a multi-year/multi-task focused technology effort is, today, highly focused on conventional high-thrust cryogenic liquid chemical rocket engines and their envisioned future technology needs. But as highlighted in the U.S. National Ten-Year Space Launch Technology Plan, a set of less-conventional propulsion subjects, ones which offer significant promise for both, improving the state of the art and opening up new propulsion-capability possibilities, is now directed to the space propulsion planning community's attention. In conducting its forward-planning activities, it is highly appropriate that the ETO Program (and other programs as well) carefully consider integrating these "new initiative" subjects into the taskwork of future years. After an introductory consideration of the National Plan's propulsion-related directives, followed by a brief background overview of the ETO Program, the following specific new-initiative candidates are discussed from the standpoint of technology-program planning: operationally efficient propulsion systems; high-thrust hybrid rocket propulsion; low-cost, low-pressure expendable propulsion subsystems; advanced cryogenic in-space propulsion systems; integrated modular engine (IME) configured propulsion systems, and combined-cycle airbreathing/rocket propulsion systems.

Escher, William J. D.↗

NASA NTRS1992

Technical note - Plasma-sprayed ceramic thermal barrier coatings for smooth intermetallic alloys

A new approach for plasma spray deposition of ceramic thermal barrier coatings directly to smooth substrates is described. Ceramic thermal barrier coatings were directly applied to substrates that had been coated with low-pressure plasma sprayed NiCrAlY bond coats and then centerless ground to simulate a smooth oxidation-resistant substrate. As the high-temperature oxidation behavior of NiAl+Zr is superior to that of MCrALY alloy, the bond coat is not required for oxidation resistance.

Miller, R. A.↗

NASA NTRS1992

Optically stimulated electron emission - Current-voltage response and spectral sensitivity

A highly reproducible optically stimulated electron emission (OSEE) response steel was achieved in laboratory conditions through suppression of surface photochemistry by replacing air with argon. This permitted the characterization of the OSEE process on D6AC steel as a photodiode. With a low-pressure mercury light source, most of the OSEE current is attributed to photoelectrons released by the 185-nm mercury line with only about 5 percent of the photocurrent associated with the 254-nm line. The forward current-voltage characteristic of the OSEE diode is linear for small fields changing to a square root response at larger fields. These results are all consistent with established theories.

Welch, Christopher S.↗

NASA NTRS1992

Plasma copolymerization of ethylene and tetrafluoroethylene

An IR and XPS study of the low-pressure, radiofrequency, glow-discharge plasma copolymerization of ethylene (ET) and tetrafluoroethylene (TFE) is presented. The potential for creating Tefzel- or Teflon-like coatings on various polymeric substrates for use in advanced life support systems is examined.

Golub, Morton A.↗

NASA NTRS1957

Nonmetallic Material Compatibility with Liquid Fluorine

Static tests were made on the compatibility of liquid fluorine with several nonmetallic materials at -3200 F and at pressures of 0 and 1500 pounds per square inch gage. The results are compared with those from previous work with gaseous fluorine at the same pressures, but at atmospheric temperature. In general, although environmental effects were not always consistent, reactivity was least with the low-temperature, low-pressure liquid fluorine. Reactivity was greatest with the warm, high-pressure gaseous fluorine. None of the liquids and greases tested was found to be entirely suitable for use in fluorine systems. Polytrifluorochloroethylene and N-43, the formula for which is (C4F9)3N, did not react with liquid fluorine at atmospheric pressure or 1500 pounds per square inch gage under static conditions, but they did react when injected into liquid fluorine at 1500 pounds per square inch gage; they also reacted with gaseous fluorine at 1500 pounds per square inch gage. While water did not react with liquid fluorine at 1500 pounds per square inch gage, it is known to react violently with fluorine under other conditions. The pipe-thread lubricant Q-Seal did not react with liquid fluorine, but did react with gaseous fluorine at 1500 pounds per square inch gage. Of the solids, ruby (Al2O3) and Teflon did not react under the test conditions. The results show that the compatibility of fluorine with nonmetals depends on the state of the fluorine and the system design.

Price, Harold G , Jr↗

NASA NTRS1926

Experimental investigation of the physical properties of medium and heavy oils, their vaporization and use in explosion engines. Part I

While little has been accomplished in obtaining an abundant supply of light oils from coal and heavy oils, progress has been made on engine design to make use of the heavier oils. Progress has been made in two different directions which are outlined in this paper: the group of engines with medium and high-pressure carburetion in the cylinder; and the group of engines with low-pressure carburetion of the heavy oils before reaching the cylinder.

OILS↗

NASA NTRS1940

Stability of Castering Wheels for Aircraft Landing Gears

A theoretical study was made of the shimmy of castering wheels. The theory is based on the discovery of a phenomenon called kinematic shimmy. Experimental checks, use being made of a model having low-pressure tires, are reported and the applicability of the results to full scale is discussed. Theoretical methods of estimating the spindle viscous damping and the spindle solid friction necessary to avoid shimmy are given. A new method of avoiding shimmy -- lateral freedom -- is introduced.

Kantrowitz, Arthur↗

NASA NTRS1953

Aerodynamic Forces and Loadings on Symmetrical Circular-Arc Airfoils with Plain Leading-Edge and Plain Trailing-Edge Flaps

An investigation has been made in the Langley two-dimensional low-turbulence tunnel and in the Langley two-dimensional low-pressure tunnel of 6- and 10-percent-thick symmetrical circular-arc airfoil sections at low Mach numbers and several Reynolds numbers. The airfoils were equipped with 0.15-chord plain leading-edge flaps and 0.20-chord plan trailing-edge flaps. The section lift and pitching-moment characteristics were determined for both airfoils with the flaps deflected individually and in combination. The section drag characteristics were obtained for the 6-percent-thick airfoil with the flaps partly deflected as low-drag-control flaps and for airfoils with the flaps neutral. Surface pressures were measured on the 6-percent-thick airfoil section with the flaps deflected either individually or in appropriate combination to furnish flap load and hinge-moment data applicable to the structural design of the airfoil. A generalized method is developed that permits the determination of the chordwise pressure distribution over sharp-edge airfoils with plain leading-edge flaps and plain trailing-edge flaps of arbitrary size and deflection.

Cahill, Jones F↗

NASA NTRS1931

Effect of viscosity in speed measurements with double-throat Venturi tubes

In order to clarify the viscosity effect some experiments were made in the Gottigen low-pressure tunnel with the Bruhn double-throat Venturi tube. This type of tunnel makes it possible to vary the pressure and thereby the density within wide limits and consequently, to examine the viscosity effect. This, however, did not impair the results because pressure and temperature were determined at different periods.

Peters, H↗

NASA NTRS1992

Mechanisms of flow control with the unsteady bleed technique

The unsteady bleed technique (a.k.a. internal acoustic forcing) has been shown to be an effective method for control of separation on low Reynolds number airfoils, blunt-end cylinders aligned axially with the flow, cylinders aligned perpendicular to the flow, and forebody geometries at high angles of attack. In many of these investigations, the mechanism for the control has been attributed to enhancement of the shear layer (Kelvin-Helmholtz) instability by the unsteady component of the forcing. However, this is not the only possible mechanism, nor may it be the dominant mechanism under some conditions. In this work it is demonstrated that at least two other mechanisms for flow control are present, and depending on the location and the amplitude of the forcing, these may have significant impact on the flow behavior. Experiments were conducted on a right-circular cylinder with a single unsteady bleed slot aligned along the axis of the cylinder. The effects of forcing frequency, forcing amplitude, and slot location on the azimuthal pressure distribution were studied. The results suggest that a strong vortical structure forms near the unsteady bleed slot when the slot location is upstream of the boundary layer separation point. The structure is unsteady, since it is created by the unsteady forcing. The 'vortex' generates a sizeable pressure spike (C(sub p) = -3.0) in the time-averaged pressure field immediately downstream of the slot. In addition to the pressure spike, the boundary layer separation location moves farther downstream when the forcing is activated. Delay of the separation is believed to be a result of enhancing the Kelvin-Helmholtz instability. When forcing is applied in a quiescent wind tunnel, a weak low-pressure region forms near the slot that is purely the result of the second-order streaming effect.

Williams, D. R.↗

NASA NTRS1959

Review of Aircraft Altitude Errors Due to Static-Pressure Source and Description of Nose-Boom Installations for Aerodynamic Compensation of Error

A brief review of airplane altitude errors due to typical pressure installations at the fuselage nose, the wing tip, and the vertical fins is presented. A static-pressure tube designed to compensate for the position errors of fuselage-nose installations in the subsonic speed range is described. This type of tube has an ogival nose shape with the static-pressure orifices located in the low-pressure region near the tip. The results of wind-tunnel tests of these compensated tubes at two distances ahead of a model of an aircraft showed the position errors to be compensated to within 1/2 percent of the static pressure through a Mach number range up to about 1.0. This accuracy of sensing free-stream static pressure was extended up to a Mach number of about 1.15 by use of an orifice arrangement for producing approximate free-stream pressures at supersonic speeds and induced pressures for compensation of error at subsonic speeds.

Gracey, William↗

NASA NTRS1959

Tire-to-Surface Friction Especially Under Wet Conditions

The results of measurements of the maximum friction available in braking on various runway surfaces under various conditions is shown for a C-123B airplane and comparisons of measurements with a tire-friction cart on the same runways are made. The.results of studies of wet-surface friction made with a 12-inch-diameter low-pressure tire on a tire-friction treadmill, with an automobile tire on the tire-friction cart, and with a 44 x 13 extra-high-pressure type VII aircraft tire at the Langley landing-loads track are compared. Preliminary results of tests on the tire-friction treadmill under wet-surface conditions to determine the effect of the wiping action of the front wheel of a tandem-wheel arrangement on the friction available in braking for the rear wheel are given.

Sawyer, Richard H.↗

NASA NTRS1961

Alignment Charts for Transport Properties Viscosity, Thermal Conductivity, and Diffusion Coefficients for Nonpolar Gases and Gas Mixtures at Low Density

Alignment charts (nomographs) designed to permit rapid calculations of the low-pressure transport properties of nonpolar gases and gas mixtures are presented. Calculations for pure gases are based on the rigorous kinetic theory of gases as applied to a realistic intermolecular force law. Mixture viscosities and conductivities are calculated from good approximations derived from rigorous theory. The properties are calculable with a precision of 2 percent or better. Accuracy depends on how well the constants characterizing the Intermolecular force law are known; if constants are derived from experimental data, results should be accurate to 5 percent or better. Force constants are tabulated for 65 gases.

Brokaw, Richard S.↗

NASA NTRS1985

Simulation of Blunt-Fin-Induced Shock-Wave and Turbulent Boundary-Layer Interaction

The Reynolds-averaged Navier-Stokes equations are solved numerically for supersonic flow over a blunt fin mounted on a flat plate. The fin shock causes the boundary layer to separate. which results in a complicated, three-dimensional shock-wave and boundary-layer interaction. The computed results are in good agreement with the mean static pressure measured on the fin and the flat plate. The main features, such as peak pressure on the fin leading edge and a double peak on the plate. are predicted well. The role of the horseshoe vortex is discussed. This vortex leads to the development of high-speed flow and, hence, low-pressure regions on the fin and the plate. Different thicknesses of the incoming boundary layer have been studied. Varying the thicknesses by an order of magnitude shows that the size of the horseshoe vortex and, therefore, the spatial extent of the interaction are dominated by inviscid flow and only weakly dependent on the Reynolds number. Colored graphics are used to show details of the interaction flow field.

Hung, Ching-Mao↗

NASA NTRS1988

Radiation in controlled environments: influence of lamp type and filter material

Radiation in controlled environments was characterized using fluorescent and various high-intensity-discharge (HID) lamps, including metal halide, low-pressure sodium, and high-pressure sodium as the radiation source. The effects of water, glass, or Plexiglas filters on radiation were determined. Photosynthetic photon flux (PPF, 400 to 700 nm), spectra (400 to 1000 nm), shortwave radiation (285-2800 nm), and total radiation (300 to 100,000 nm) were measured, and photosynthetically active radiation (PAR, 400 to 700 nm) and longwave radiation (2800 to 100,000 nm) were calculated. Measurement of PPF alone was not an adequate characterization of the radiation environment. Total radiant flux varied among lamp types at equal PPF. HID lamps provided a lower percentage of longwave radiation than fluorescent lamps, but, when HID lamps provided PPF levels greater than that possible with fluorescent lamps, the amount of longwave radiation was high. Water was the most effective longwave radiation filter. Glass and Plexiglas similarly filtered longwave more than shortwave radiation, but transmission of nonphotosynthetic shortwave radiation was less with Plexiglas than glass. The filter materials tested would not be expected to influence photomorphogenesis because radiation in the action spectrum of phytochrome was not altered, but this may not be the only pigment involved.

NASA Discipline Life Support Systems↗

NASA NTRS1937

Stability of Castering Wheels for Aircraft Landing Gears, Special Report

In many installations of castering rubber-tired wheels there is a tendency for the wheel to oscillate violently about the spindle axis. This phenomenon, popularly called 'shimmy,' has occurred in some airplane tail wheels and has been corrected in two ways: first by the application of friction in the spindles of the tail wheels; and, second, by locking the wheels while taxiing at high speeds. Shimmy is common with the large wheels used as nose wheels in tricycle landing gears and, since it is impossible to lock the wheels, friction in the nose-wheel spindle has been the sole means of correction. Because the nose wheel is larger than the conventional tail wheel and usually carries a greater load, the larger amounts of spindle friction necessary to prevent shimmy are objectionable. the present paper presents a theoretical and experimental study of the problem of the stability of castering wheels for airplane landing gears. On the basis of simplified assumptions induced from experimental observations, a theoretical study has been made of the shimmy of castering wheels. The theory is based on the discovery of a phenomenon called 'kinematic shimmy' and is compared quantitatively with the results of model experiments. Experimental checks, using a model having low-pressure tires, are reported and the applicability of the results to full scale is discussed. Theoretical methods of estimating the spindle viscous damping and spindle solid friction necessary to avoid shimmy - lateral freedom - is introduced.

Kantrowitz, Arthur↗