Search NASA⌕ Search

SEARCH · Search NASA

Results for “module efficiency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

2.3-MW Medium-Voltage, Three-Level Wind Energy Inverter Applying a Unique Bus Structure and 4.5-kV Si/SiC Hybrid Isolated Power Modules: Preprint

A high-efficiency, 2.3-MW, medium-voltage, three-level inverter utilizing 4.5-kV Si/SiC (silicon carbide) hybrid modules for wind energy applications is discussed. The inverter addresses recent trends in siting the inverter within the base of multimegawatt turbine towers. A simplified split, three-layer laminated bus structure that maintains low parasitic inductances is introduced along with a low-voltage, high-current test method for determining these inductances. Feed-thru bushings, edge fill methods, and other design features of the laminated bus structure provide voltage isolation that is consistent with the 10.4-kV module isolation levels. Inverter efficiency improvement is a result of the (essential) elimination of the reverse recovery charge present in 4.5-kV Si PIN diodes, which can produce a significant reduction in diode turn-off losses as well as insulated-gate bipolar transistor (IGBT) turn-on losses. The hybrid modules are supplied in industry-standard 140 mm x 130 mm and 190 mm x 130 mm packages to demonstrate direct module substitution into existing inverter designs. A focus on laminated bus/capacitor-bank/module subassembly level switching performance is presented.

17 WIND ENERGY↗

A transmissive, spectrum-splitting concentrating photovoltaic module for hybrid photovoltaic-solar thermal energy conversion

Here, a spectrum splitting, transmissive concentrating photovoltaic (tCPV) module is proposed and designed for a hybrid photovoltaic-solar thermal(PV/T) system. This module enables the system to more fully utilize the full spectrum of incoming sunlight. By utilizing III-V triple junction solar cells with bandgaps of 2.1eV/1.7eV/1.4eVin the module, ultraviolet (UV) and visible light will be absorbed and converted to electricity, while infrared (IR) light will pass through and be captured by a solar thermal receiver and stored as heat. The stored heat energy may be dispatched as electricity or process heat, as needed.Numerical analysis based on the Finite Elemental Method (FEM), ray tracing, circuit analysis, device modelling, and more is employed to design this tCPV module. According to these simulations, the tCPV module can perform with overall power conversion efficiency exceeding 43.5% for above bandgap (in-band)light under a standard AM1.5D solar spectrum, under an average concentration ratio of 400 suns.Passive and active cooling methods, keeping cells below 110°C, are also investigated and discussed, indicating that a transparent active cooling design could improve the CPV module efficiency by around 1%(absolute), relative to a passive design,by reducing the maximum cell working temperature by ~16°C. Furthermore, cost analysis shows that installation cost of around 1.9/W–2.2/W could be reached for the tCPV based PV/T system,which shows a competitive economic advantage compared to a more conventional PV with battery system.

14 SOLAR ENERGY↗

Reducing Operating Temperature in Photovoltaic Modules

Reducing the operating temperature of photovoltaic modules increases their efficiency and lifetime. This can be achieved by reducing the production of waste heat or by improving the rejection of waste heat. We tested, using a combination of simulation and experiment, several thermal modifications in each category. To predict operating temperature and energy yield changes in response to changes to the module, we implemented a physics-based transient simulation framework based almost entirely on measured properties. The most effective thermal modifications reduced the production of waste heat by reflecting unusable light from the cell or the module. Consistent with previous results and verified in this work through year-long simulations, the ideal reflector resulted in an annual irradiance-weighted temperature reduction of 3.8 K for crystalline silicon (c-Si). Our results illustrate that more realistic reflector concepts must balance detrimental optical effects with the intended thermal effects to realize the optimal energy production advantage. Methods improving thermal conductivity or back-side emissivity showed only modest improvements of less than 1 K. We also studied a GaAs module, which uses high-efficiency and high-subbandgap reflectivity to operate at an annual irradiance-weighted temperature 12 K cooler than that of a c-Si module under the same conditions.

14 SOLAR ENERGY↗

Multiple stack fuel cell system with shared plenum

A multi-stack fuel cell system is disclosed where multiple fuel cell stacks can be efficiently connected together. The fuel cell system includes a plurality of fuel cell modules include a sealed planar fuel cell stack that has internal manifold channels for transport of fuel and air to fuel cells within the stack and transport of tail gas and spent air away from fuel cells within the stack. Each of the fuel cell stacks is mounted on a base manifold, and the base manifold has side openings in fluid communication with the stack internal manifold channels. The side openings on the base manifold are configured so that the modules can be efficiently connected together.

Schneider, Jonathan↗

Properties of Encapsulated CIGS Cells in 85 degrees C/85%RH

This paper concerns studies of encapsulated cells subjected to an environment of 85ºC and 85%RH (85/85). Cells are encapsulated with PNNL multi-layer coatings (referred to as PML coatings) utilizing alternating layers of Al2O3, and an advanced polymer. The new polymer has been determined to withstand the 85/85 environment. Two types of cells were used for these studies, namely, SSI mini-modules (which are actually CIGSS devices) and CIGS cells provided by the Institute of Energy Conversion (IEC). Cells were coated and stressed at 85/85 in an environmental chamber. Current-voltage characteristics were acquired before and after coating, and periodically after being subjected to the 85/85 environment. Whereas coated SSI modules were determined to last 1000 hours when stressed at 60ºC/90%RH without degradation, the efficiency of these modules degrade to a level of 60% of the beginning-of-life value when stressed at 85/85. Encapsulated IEC cells, however, have exhibited extraordinary results. The efficiency of several encapsulated cells did not decrease for 1500 hours in an 85ºC/85%RH environment. This results establishes a benchmark for stressed, encapsulated CIGS cells.

14 SOLAR ENERGY↗

High-Efficiency Low-Cost Thin-Film GaAs Photovoltaic Module Development Program: July 14, 2010 - January 13, 2012 (Final Technical Progress Report)

This is the final technical progress report of the High-Efficiency Low-Cost Thin-Film GaAs Photovoltaic Module Development Program. Alta Devices has successfully completed all milestones and deliverables established as part of the NREL PV incubator program. During the 18 months of this program, Alta has proven all key processes required to commercialize its solar module product. The incubatorfocus was on back end process steps directed at conversion of Alta's high quality solar film into high efficiency 1-sun PV modules. This report describes all program deliverables and the work behind each accomplishment.

14 SOLAR ENERGY↗

A New Vehicle-to-Vehicle Communication System: Visual-Enhanced Cooperative Traffic Operations

The advent of Connected and Autonomous Vehicles (CAVs) has highlighted the necessity for robust communication systems between vehicles and their environment. This study introduces a novel vehicle-to-vehicle (V2V) communication system, termed the Visual-Enhanced Cooperative Traffic Operations (VECTOR) system. The VECTOR system addresses the need for robust communication by converting dynamic data (including velocity and yaw angle data) into binary code, which is displayed on an LED panel mounted on the top of the vehicle. Following vehicles detect this panel and decode the information using a camera, implementing a visual-based communication method. VECTOR system employs a comprehensive five-module process. Initially, polynomial fitting techniques are applied to velocity data over fixed time intervals using third-degree polynomials, with validation via R² and MSE metrics. The second module converts velocity and yaw angle data into binary form, thereby enhancing detection and processing efficiency. The third module focuses on improving detection stability across various environmental conditions to enhance traffic safety. The fourth module decodes the binary data back into trajectory information, ensuring the fidelity of velocity and yaw angles. The final module integrates eco-control through the VECTOR system, employing advanced control algorithms to minimize energy consumption in CAVs. Experimental evaluations conducted using a modified CAV test platform based on the Lincoln MKZ demonstrate the feasibility and efficiency of the VECTOR system, achieving a 75% R-squared accuracy rate in replicating original velocity data. This methodology not only highlights potential applications but also underscores significant implications for advancing CAV technology.

Ma, Ke↗

Transmissive concentrated photovoltaic module with cooling system

A spectrum splitting, transmissive concentrating photovoltaic (tCPV) module is proposed and designed for a hybrid photovoltaic-solar thermal (PV/T) system. The system may be able to fully utilize the full spectrum of incoming sunlight. By utilizing III-V triple junction solar cells with bandgaps of approximately 2.1 eV, 1.7 eV, and 1.4 eV in the module, ultraviolet (UV) and visible light (in-band light) are absorbed and converted to electricity, while infrared (IR) light (out-of-band light) passes through and is captured by a solar thermal receiver and stored as heat. The stored heat energy may be dispatched as electricity or process heat as needed. The tCPV module may have an overall power conversion efficiency exceeding 43.5% for above bandgap (in-band) light under a standard AM1.5D solar spectrum with an average concentration ratio of 400 suns. Passive and/or active cooling methods may be used to keep cells below 110° C. while transmitting >75% of out-of-band light to the thermal receiver, which may attain thermal energy capture at temperatures as high as 500° C. or more. A transparent active cooling system may improve the CPV module efficiency by about 1% (absolute) relative to a passive cooling system by reducing the maximum cell working temperature by about 16° C.

Escarra, Matthew David↗

Non-streaming high-efficiency perforated semiconductor neutron detectors, methods of making same and measuring wand and detector modules utilizing same

Non-streaming high-efficiency perforated semiconductor neutron detectors, method of making same and measuring wands and detector modules utilizing same are disclosed. The detectors have improved mechanical structure, flattened angular detector responses, and reduced leakage current. A plurality of such detectors can be assembled into imaging arrays, and can be used for neutron radiography, remote neutron sensing, cold neutron imaging, SNM monitoring, and various other applications.

McGregor, Douglas S↗

Enhancement of Optical Efficiency of CSP Mirrors for Reducing O&M Cost via Near-Continuous Operation of Self-Cleaning Electrodynamic Screens (EDS). Final Report

Over the past decade, techno-economical advancements in solar energy systems, particularly the improvement in the conversion efficiency of PV modules made with mono-crystalline silicon solar cells from 12% to 20%, as well as the cost reduction in manufacturing by a factor of about 10%, have made it possible to achieve a levelized cost of electricity (LCOE) in PV plants that is comparable to, or less than, the cost of deriving electricity from fossil fuels. Operating PV plants in mid-latitude sun-belt regions, where the solar irradiance level is highest, provides a high annual energy-yield (kWh/kWp) due to two factors: (1) the availability of predictable high solar irradiance throughout the year with the fewest interruptions in solar flux from clouds and rain, and (2) the increased conversion efficiency of crystalline solar cells, as recombination loss has decreased with increased intensity of the sunlight that illuminates the silicon solar cells. Semi-arid and desert regions, however, are plagued by high atmospheric dust concentrations and frequent sand storms. The deposition of a layer of dust on the optical surfaces of solar collectors such as PV modules and concentrating mirrors reduces the transmission efficiency of sunlight that actually reaches the solar cells or receivers, resulting in high energy-yield soiling loss. There are two major cost components to operating a solar plant: (1) installation costs, and (2) operation-and-maintenance (O&M) costs. There is no fuel cost; hence operating a solar plant in a semi-arid or desert region provides high returns on investment if soiling losses are mitigated via efficient cleaning methods and optimized cleaning frequency. If solar collectors are not cleaned, the accumulation of dust layers on solar collectors may cause the operation of such plants in arid regions to become economically unviable. Washing solar collectors with water and detergent, as is most commonly done now, is an efficient method for cleaning. The conventional approach in utility-scale solar plants is to use a large truck with a water tank and pump system for spraying deionized water on the surface of the solar collectors. Robotic cleaning with brushes, used for many solar plants, requires lesser water for cleaning. The water consumed using semi-automated cleaning of PV modules in utility-scale solar plants is approximately 2 liters/m 2 per cleaning cycle. The total optical surface area of the solar collectors in 1 TW-scale solar installation will be more than 3 × 109 m 2 ; hence an enormous amount of water be needed for cleaning. There simply is not enough fresh water in the sun-belt areas of the world for predicted cleaning needs. In solar power plants, the estimated cost of cleaning solar collectors includes expenses related to the equipment used, labor, cost of transportation of water, the energy required for cleaning, plus ancillary costs whereas the cost of water is not considered. The water used is obtained from sources located close to plant sites, unmindful of the environmental and societal impact as the power plants are oftentimes located in regions that face severe drought. This practice is very similar to the cost calculations in deriving the levelized cost of electricity (LCOE) in conventional power plants based on burning fossil fuel such as coal and gas, while disregarding the cost of climate change and health effects. Unless a water-free or low-water cleaning method is established, the expansion of solar plants may lose public support in areas suffering long intervals of drought. The goal of this research project has been the development and application of the Electrodynamic Screen (EDS) as a means for a water-free, scalable cleaning process applicable to solar-power installations, including rooftop applications. We describe here the development of an EDS film-based cleaning process as an emerging method for use on PV modules, parabolic troughs, and heliostats. This report aims to show the feasibility of integrating or retrofitting EDS films onto the optical surfaces of solar collectors (both PV and CSP) while maintaining high transmission or reflection efficiency. The cleaning action provided by the EDS film is an active method to remove dust deposits by electrodynamic force. Current lab-scale prototype EDS films, retrofitted onto solar panels and mirrors, have shown to be capable of maintaining optical transmission or specular-reflection efficiencies higher than 90% of initial values under clean conditions. The optical surfaces of solar collectors laminated with EDS films can remove more than 90% of deposited dust when the EDS is activated for less than two minutes. As an electrodynamic dust removal process, the EDS film-based method is designed primarily for the removal of dust in solar installations located in semi-arid and desert areas, where the atmosphere is often dry and dusty and rainfall is infrequent. While EDS film application minimizes water consumption and facilitates cleaning as frequently as needed, it has limitations in removing contaminants such as soot, organic pollutants deposited as fine films on the surface, and bird droppings. The dust removal efficiency of the EDS is maximum at relative humidity RH is 40 to 50% and decreases at when RH > 65%. Many solar plant sites undergo diurnal and seasonal cycles of high ambient, early afternoon temperatures and an RH that reaches the dew point early in the morning. These variations in atmospheric conditions do not limit the operation of the EDS film. This report presents a brief review of the progress and the potential of EDS film technology for mitigating the impact of dust on solar collectors via water-free cleaning, as well as current technical challenges regarding efficiency and durability. Our experimental data on the performance of EDS films show that: (1) the dust-removal efficiency (DRE) can reach levels higher than 90%, (2) the specular reflectivity (SR) of EDS film-laminated second-surface mirrors reach levels in excess of 90%, (3) the specular reflectivity restoration (SRR) can exceed 90%, (4) the output-power restoration (OPR) of PV modules can exceed 95%, and (5) the optical transmission efficiency (TE) of the EDS films can be greater than 90%. Working with Sandia National Laboratories (NM), Corning Research and Development Corporation (NY), Eastman Kodak (NY), Tomark-Worthen Industries (NH), and EDS Chile SPA (Chile), we have produced EDS film-laminated PV modules and demonstrated their self-cleaning functions without requiring water. We have demonstrated that the operational range of EDS films will cover the expected ambient temperature of solar fields at RH cycling varying from 20 to 95% as long as the EDS films are activated in the RH range 20 to 50%. (Typical solar-field climates in deserts and semi-arid lands often reach near dew point in coastal areas.) Our experiments on the application of hydrophobic-fluorinated nanoparticle coatings on EDS film surfaces show that the EDS operational range can be extended to higher RH levels that approach the dew point. At Eastman Kodak, as one of our industrial partners, we were able to establish a process for manufacturing EDS films using flexographic printing of the electrodes onto transparent polymer films. This process utilizes an existing manufacturing line at Eastman Kodak that allows fabrication of medium-scale EDS films (26 cm × 30 cm). The manufacturing process has the capacity to produce EDS films at high production speeds. The medium-scale EDS films that have been printed at Kodak were evaluated in the lab at Boston University. The EDS films produced at Kodak were laminated at Tomark-Worthen using an industrial scale vacuum laminator to produce EDS film stacks, which can be affixed onto the optical surfaces of PV modules or concentrating mirrors. The EDS film stack consists of the EDS films that have Willow® Glass (WG) which has a thickness of 100 μm as the front surface. The WG sheets obtained from Corning Research and Development Corporation are customized in size and shape to cover the active area of the EDS films. The back surface of the EDS film stack is integrated onto the optical surface of the solar panel or mirror using optically clear adhesive (OCA) films or silicone adhesives. The OCA films (thickness 25 μm) are produced by 3M. The EDS film stacks have the architecture: WG/OCA/EDS Film/OCA/ over PV module or solar mirror. The power-supply units needed for activating the electrodes of the EDS film were designed and produced at Boston University. These power supply units provide three-phase, 1.2 kV voltage pulses at a very low current (micro-ampere) level and at a low frequency (≈ 5 Hz). The voltage pulses are applied to the electrodes in a sequence such that the train of pulses resembles a unidirectional traveling wave of electrical field on the surface of the EDS film. The dust particles on the surface become charged electrostatically and are levitated by the Coulomb force. The lateral sweeping action of the traveling electric field created by the three-phase voltages pulses then sweeps the dust off the surface. The energy consumed by the EDS electrodes is less than 0.2 Wh/m 2 /cleaning cycle, enabling energy-efficient restoration of output power (OPR) of PV module or specular reflectivity restoration (SRR) for solar mirrors. The EDS system consists of (1) an EDS film stack laminated onto the solar collectors, (2) connection of the EDS film to its power supply unit and (3) Interconnection of the power supply to PV modules or solar mirrors. Design, construction and assessment of field-testing units that have EDS stack laminated PV modules for evaluating the performance of the EDS films in solar fields is being carried out at BU. Our progress under this project, aimed at the advancement of EDS film technology, has reached DOE Technology Readiness Level (TRL) 6. Based on the extensive laboratory evaluations and limited field trials, as well as contacts with potential users, we believe that the technology has reached its commercial stage. We are conducting a cost analysis using the National Renewable Energy Laboratory (NREL) System Advisory Model (SAM) and are preparing for field trials of EDS films in different solar fields in the US, Chile, India and in the Middle East. A brief description of EDS film performance, construction and testing of the field-test unit, autonomous operation of the field-test unit for evaluating EDS performance in increasing energy yield, associated revenue savings, and water conservation is presented.

14 SOLAR ENERGY↗

Final Design of the SLAC P2 Marx Klystron Modulator

The SLAC P2 Marx has been under development for two years, and follows on the P1 Marx as an alternative to the baseline klystron modulator for the International Linear Collider. The P2 Marx utilizes a redundant architecture, air-insulation, a control system with abundant diagnostic access, and a novel nested droop correction scheme. This paper is an overview of the design of this modulator. There are several points of emphasis for the P2 Marx design. First, the modulator must be compatible with the ILC two-tunnel design. In this scheme, the modulator and klystron are located within a service tunnel with limited access and available footprint for a modulator. Access to the modulator is only practical from one side. Second, the modulator must have high availability. Robust components are not sufficient alone to achieve availability much higher than 99%. Therefore, redundant architectures are necessary. Third, the modulator must be relatively low cost. Because of the large number of stations in the ILC, the investment needed for the modulator components is significant. High-volume construction techniques which take advantage of an economy of scale must be utilized. Fourth, the modulator must be simple and efficient to maintain. If a modulator does become inoperable, the MTTR must be small. Fifth, even though the present application for the modulator is for the ILC, future accelerators can also take advantage of this development effort. The hardware, software, and concepts developed in this project should be designed such that further development time necessary for other applications is minimal.

43 PARTICLE ACCELERATORS↗

Flexible‐rate optoelectronic wireless transmission system at 101 GHz using multiband CAP‐PAM modulation and envelope detection

Abstract In this paper, we have experimentally demonstrated the first flexible‐rate optoelectronic terahertz wireless transmission system at 101 GHz based on multiband CAP‐PAM modulation and cost‐efficient envelope detection. Instead of traditional M‐QAM mapping, PAM‐N mapping is used in CAP modulation with low‐computational complexity. The system performances and optimal capacity in both single‐band case and multiband case are intensively investigated. The results show that the highest data rate for single‐band system is 13.35 Gbit/s with CAP‐PAM‐5 modulation, while the optimum aggregate transmission line rate of 8.49 Gbit/s can be obtained with 4‐sub‐bands CAP‐PAM‐{5,3,2,2} modulation under 7% FEC limit of 3.8 × 10 −3 for four‐user access.

Zhang, Jiao↗

New features of the ECH control system on DIII-D and impact of power modulation on collector loading

In order to increase the reliability and improve the availability of electron cyclotron heating (ECH) and current drive during a plasma shot, an adaptive gyrotron command generator has been designed and implemented in all gyrotron systems on the DIII-D tokamak. This adaptive real-time generator is able to detect imminent faults, including gyrotron body overcurrent faults that can develop in a few microseconds, block faults, and restart RF generation within 10–30 ms, faster than the DIII-D energy confinement time. The adoption of this adaptive generator has substantially improved the performance of a depressed-collector gyrotron with recurrent body current faults, and has assisted the ECH system to achieve a record reliability of 95% during the last experimental campaign. The impact of power modulation on the collector loading of a depressed-collector gyrotron has been experimentally studied using calorimetry and collector maps taken by a diagnostic developed in-house. While lowering the modulation duty cycle kept the collector power constant as a result of low beam-wave efficiency during the modulation low state, an observed power redistribution inside the collector increased the peak collector power density, which reached levels above the manufacturer power density limit for low duty cycles.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Intraday Outdoor Efficiency Changes in Metal-Halide Perovskite Photovoltaic Modules

Here, we present outdoor observations of metal-halide perovskite modules deployed in the Photovoltaic Accelerator for Commercializing Technologies center, which houses one of the world's broadest efforts to test metal-halide perovskite photovoltaic modules outdoors. As of January 2025, outdoor testing has encompassed over 150 modules from 14 different partners. Our findings illustrate how daily changes in efficiency, driven by exposure to light, affect field performance in real-world conditions. These effects cannot be explained by existing outdoor performance models and frustrate the notion of a traditional temperature coefficient.

14 SOLAR ENERGY↗

Efficient generation of fast ions from surface modulated nanostructure targets irradiated by high intensity short-pulse lasers

It's shown that the imposition of sub-laser wavelength relief structures on the surface of mass-limited-targets results into several folds higher short-pulse laser absorption, and consequently the efficient generation of fast ions. The optimum relief parameters for enhanced short-pulse laser absorption and higher ion acceleration are estimated numerically by particle-in-cell simulations and then corroborated by analytical scalings. The stability of the pre-imposed surface modulation during the laser pulse foil interaction is also examined.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Doping and energy band modulation of nanoporous electrodes for enhancing power conversion efficiency of dye-sensitized solar cells

Highlights: • Cd and La are co-doped into TiO{sub 2} by sol-gel method. • La dopant modulates particle size to enhance dye adsorption. • Cd dopant causes decrease in band gap of TiO{sub 2} and creates trap sites. • Only small amount of Cd dopant required for the favorable decrease in band gap. • 24% of efficiency increment for 0.1 mol% Cd-La TiO{sub 2} compared to pure TiO{sub 2}. - Abstract: This work report, for the first time, the co-doping of mesoporous TiO{sub 2} with Cd{sup 2+} and La{sup 3+} cations for improved performance of dye-sensitized solar cells (DSSCs). Cd{sup 2+} ions modify the TiO{sub 2} lattice interstitially and lower the band gap enabling better electron injection. La{sup 3+} ions, having a larger ionic radius compared to that of Ti{sup 4+} ions, occupy interstitial sites and modulate particle size which increase surface area, hence the dye adsorption. The result demonstrates that DSSC employed with 0.1 mol% Cd-La co-doped TiO{sub 2} anode an increase in power conversion efficiency of 24% compared to DSSC with pure TiO{sub 2} anode. The doping concentration has to remain low as not to completely transform the morphology of TiO{sub 2} and to decrease the number of oxygen vacancies forming trap sites for recombination. The selection of ionic radius of dopants is significant as they can modify the TiO{sub 2} lattice either by substitution or interstitial of titanium ions.

36 MATERIALS SCIENCE↗