SEARCH · Search NASA

Results for “neutron moderator”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

All sources NASA NTRS DOE OSTI

DOE OSTI2024

Porous Iron Electrodes Reduce Energy Consumption During Electrocoagulation of a Virus Surrogate: Insights into Performance Enhancements Using Three-Dimensional Neutron Computed Tomography

Electrocoagulation has attracted significant attention as an alternative to conventional chemical coagulation because it is capable of removing a wide range of contaminants and has several potential advantages. In contrast to most electrocoagulation research that has been performed with nonporous electrodes, in this study, we demonstrate energy-efficient iron electrocoagulation using porous electrodes. In batch operation, investigation of the external pore structures through optical microscopy suggested that a low porosity electrode with sparse connection between pores may lead to mechanical failure of the pore network during electrolysis, whereas a high porosity electrode is vulnerable to pore clogging. Electrodes with intermediate porosity, instead, only suffered a moderate surface deposition, leading to electrical energy savings of 21% and 36% in terms of electrocoagulant delivery and unit log virus reduction, respectively. Neutron computed tomography revealed the critical role of electrode porosity in utilizing the electrode’s internal surface for electrodissolution and effective delivery of electrocoagulant to the bulk. Energy savings of up to 88% in short-term operation were obtained with porous electrodes in a continuous flow-through system. Further investigation on the impact of current density and porosity in long-term operation is desired as well as the capital cost of porous electrodes.

42 ENGINEERING↗

DOE OSTI2021

Integration of a Wigner effect-based energy storage system with an advanced nuclear reactor

In this work, an innovative energy storage concept based on the purposeful creation of defects in crystalline material by neutron irradiation is presented. Lattice defects are generated when heavy particles collide with the atoms in a crystal structure, i.e., if the incoming particles have enough energy, recoil atoms are displaced from their initial lattice sites. Most of the displaced atoms will eventually combine with nearby vacancies, but some of them will come to rest in non-ideal locations. The energy held by displaced atoms is called Wigner energy. Lattice defects can migrate and form clusters, and the Wigner energy can be released from these groupings if sufficient activation energy is provided. In the nuclear industry, this effect is well-known since it represented an issue for graphite-moderated reactors. This work presents the conceptual design of an engineering system that exploits this physical process to store the energy of neutrons in advanced reactor concepts. In the first part of the paper, the theoretical performance of an energy storage system based on the Wigner effect is described. Given the lattice properties and the compatibility with the harsh reactor environment, graphite was selected as the candidate material for the irradiation targets. Both experimental data and molecular dynamics simulations confirmed that this system can achieve performance comparable with state-of-the-art batteries in terms of stored energy density. In the second part of the paper, the engineering challenges of this innovative technology and the proposed solutions are described. After defining the optimal irradiation conditions, the different steps of the operation of the proposed energy system (from energy storing to energy harvesting) were defined. Finally, the integration of this concept with advanced reactor designs, i.e., a Sodium-cooled Fast Reactor and a Molten Salt-cooled Reactor, was investigated and the corresponding performance was evaluated.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2021

Yttrium Hydride Post Irradiation Examination Plan

The overarching goal of the Department of Energy Office of Nuclear Energy (DOE-NE) microreactor program is to develop technologies for the deployment of civilian microreactors by stakeholders1. Microreactors are expressed as advanced transportable nuclear reactors operating at low power (<20MWth) but high temperatures (>600°C), as well as plug-and-play and inherently safe designs. One prerequisite of a microreactor is the compactness, so that a truck can transport the reactor under safe conditions with the current road infrastructure1,2. The compactness of these reactors likely can be attainable by use of solid components for the essentials of the nuclear core, such as fuel, core heat removal components, reflectors, and moderators. Among these essentials, where fuel enrichment must remain < 20% to meet High Assay Low Enrichment Uranium criteria (HALEU), the largest contribution to the compactness is offered by use of solid moderators which benefit from light atomic weight elements, such as hydrogen, carbon, and beryllium2. Among these, hydrogen-bearing materials, such as metal hydrides, are superior to other options from the lowest critical mass standpoint. Noting that, factors other than critical mass should be considered for a specific reactor design. Yttrium- or zirconium-based metal hydrides have been down-selected due to their neutronic performance. In addition to the neutronic perspective, maintaining hydrogen within the metal hydride is important at the high operating temperatures proposed by advanced reactors. Yttrium hydride (YHx) is, therefore, a proposed moderator material that offers better hydrogen retention at higher operating temperatures than zirconium hydrides due to higher retention and thermal stability of hydrogen in the metal3. The irradiated materials properties of metal hydrides, in this case YHx, must be assessed for the qualification of these moderators. Material testing and inspection processes must illustrate that the effects of dimensional and property changes on thermophysical and mechanical properties do not cause any significant changes on the microreactor safety, and the moderating power is maintained within design limits. Thus, the effect of irradiation on the thermophysical and mechanical properties must be determined. This post-irradiation examination (PIE) plan specifically aims to determine these properties for YHx following Advanced Test Reactor (ATR) irradiation.

99 GENERAL AND MISCELLANEOUS↗

DOE OSTI2022

PLN-6268 Yttrium Hydride Post Irradiation Examination Plan

99 GENERAL AND MISCELLANEOUS↗

DOE OSTI2021

Generation of the TSL for Zirconium Hydrides from Ab Initio Methods

Zirconium hydride (ZrHx) is a moderator material used in TRIGA and other reactors that may exist in multiple phases with varying stoichiometry, which include the δ phase and the ϵ phase. Current ENDF/B-VIII.0 ZrHx thermal scattering law (TSL) evaluations do not distinguish between phases. These sub-libraries were generated with the LEAPR module of NJOY using historic phonon spectra derived from a central force model and assume incoherent elastic scattering for both bound hydrogen and zirconium, which neglects the effects of crystal structures important for scattering from zirconium bound in ZrHx. In this work, the TSLs for hydrogen and zirconium bound in δ-ZrHx and ϵ-ZrH2 were generated from phonon spectra derived from modern ab initio lattice dynamics methods and ab initio molecular dynamics. Subsequently, TSLs for hydrogen and zirconium in ZrHx and ZrH2 were generated using the Full Law Analysis Scattering System Hub (FLASSH) code. The built-in generalized coherent elastic routine was used to generate the previously neglected elastic contribution from zirconium for this material. The present TSLs provide both a re-evaluation of the current ZrH sub-libraries and expansion of the set of TSLs available for the examination of neutrons in systems with zirconium hydride, permitting explicit treatment of δ and ϵ phases.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2020

Re-evaluation of the TSL for Yttrium Hydride

Yttrium hydride (YH x ) is of interest as a high-temperature moderator material in advanced nuclear reactor systems because of its superior ability to retain hydrogen at elevated temperatures. Thermal neutron scattering laws (TSL) for hydrogen bound in yttrium hydride (H-YH 2 ) and yttrium bound in yttrium hydride (Y-YH 2 ) were previously evaluated by Naval Nuclear Laboratory using the ab initio approach and released in ENDF/B-VIII.0. In that work, density functional theory, incorporating the generalized gradient approximation (GGA) for the exchange-correlation energy, was used to simulate the face-centered cubic structure of YH 2 and calculate the interatomic Hellmann-Feynman forces for a 2×2×2 supercell containing 96 atoms. Lattice dynamics calculations using PHONON were used to determine the phonon density of states. The calculated phonon density of states for H and Y in YH 2 were then used to prepare H-YH 2 and Y-YH 2 TSL evaluations, in the incoherent approximation, using the LEAPR module of NJOY. In addition, elastic scattering was assumed to be incoherent for both H and Y. While the incoherent elastic scattering approximation is appropriate for H-YH 2 , it introduces an undesirable approximation for Y-YH 2 . In this work, we re-evaluate the TSL for Y-YH 2 using FLASSH (Full Law Analysis Scattering System Hub). Y-YH 2 is evaluated using the FLASSH generalized coherent elastic scattering capability in order to capture the Bragg peaks associated with the YH 2 crystal structure which were neglected in the prior NJOY-based evaluation due to limitations in LEAPR. An experimental approach to validate the Y-YH 2 TSL using neutron transmission measurements is discussed.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2025

Microreactor Assembly Transportation Cask Model Description for Criticality Safety Validation Basis Assessment

Criticality safety analyses are completed on a transportation cask used for microreactor assembly shipment to provide an example of model and analysis to industry for reproducing this type of study on their microreactor fuel shipment. The fuel assembly considered is based on a gas-cooled microreactor (GC-MR), which utilizes HALEU fuel in the form of TRISO particles and utilizes various design options considered in industry designs. Various versions of this GC-MR assembly were studied, with and without YH2 moderator, providing similar conclusions. The shipment cask design is revised based on an existing design ES-3100, developed by Y-12 for the transport of highly enriched uranium (HEU), but is enlarged to hold the GC-MR fuel assembly. Criticality safety analysis for the cask/GC-MR fuel assembly package was performed using the CSAS6 sequence of SCALE6.3.2, utilizing the ENDF/B-VII.1 based continuous energy neutron library, and the analysis strictly follows the guideline from NRC reference reports. Different scenarios, e.g. normal operation, undamaged cask with water flooded, damaged cask with optimal water moderation, have been analyzed and it could be concluded the package would always have a large margin of subcriticality even packed in an infinite array. Sensitivity and similarity analyses are also performed using the TSUNAMI sequence of SCALE6.3.2, and the similarity analysis uses all the experiments from the ICSBEP Handbook with Intermediate and Mixed Enriched Uranium (IEU) and Low Enriched Uranium (LEU) systems together with additional ones that are sponsored by the DNCSH program. These similarity analyses indicate that dry cases have no similar benchmark experiments (ck values greater than 0.8), which may become problematic if more assemblies are shipped together (or a fully loaded core is shipped) and margin to criticality is reduced. However, the damaged cask models with flooded assemblies exhibited similarities to many experiments with ck values greater than 0.8.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2026

Microreactor Assembly Transportation Cask Model Description for Criticality Safety Validation Basis Assessment (Rev. 3)

Criticality safety analyses are completed on a transportation cask used for microreactor assembly shipment to provide an example of model and analysis to industry for reproducing this type of study on their microreactor fuel shipment. The fuel assembly considered is based on a gas-cooled microreactor (GC-MR), which utilizes HALEU fuel in the form of TRISO particles and utilizes various design options considered in industry designs. Various versions of this GC-MR assembly were studied, with and without YH 2 moderator, providing similar conclusions. The shipment cask design is revised based on an existing ES-3100 design, developed by Y-12 for the transport of highly enriched uranium (HEU), but is enlarged to hold the GC-MR fuel assembly. Criticality safety analysis for the cask/GC-MR fuel assembly package was performed using the CSAS6 sequence of SCALE6.3.2, utilizing the ENDF/B-VII.1 based continuous energy neutron library, and the analysis strictly follows the guideline from NRC reference reports. Different scenarios, e.g. normal operation, undamaged cask with water flooded, damaged cask with optimal water moderation, have been analyzed and it could be concluded the package would always have a large margin of subcriticality even packed in an infinite array. Sensitivity and similarity analyses are also performed using the TSUNAMI sequence of SCALE6.3.2, and the similarity analysis uses all the experiments from the ICSBEP Handbook with Highly Enriched Uranium (HEU), Intermediate and Mixed Enriched Uranium (IEU) and Low Enriched Uranium (LEU) systems, together with additional ones that are sponsored by the DNCSH program, and selected IRPhEP experiments using TRISO fuel and graphite moderator. These similarity analyses indicate that the dry nominal design has no similar benchmark experiments (ck values greater than 0.8), which may become problematic if more assemblies are shipped together (or a fully loaded core is shipped) and margin to criticality is reduced. However, the cask models with flooded assemblies exhibited similarities to many experiments with c k values greater than 0.8.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2022

Thermal Neutron Scattering Law for Beryllium Hydride and Critical Mass Calculations [Slides]

TSLs for H(BeH 2 ) and Be(BeH 2 ) were evaluated in the incoherent approximation using FLASSH. Minimum critical mass estimates were performed using MC21 continuous energy Monte Carlo calculations with the BeH 2 TSLs. Researchers confirmed very low estimated critical mass for BeH 2 -moderated and Be- reflected spheres. These were the lowest critical masses NNL has studied to date. Future work includes relaxation of the incoherent approximation for Be(BeH 2 ). A small increase in critical mass is expected due to increased neutron transmission at sub-Bragg cutoff energies.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2025

Parity-Doubled Nucleons Can Rapidly Cool Neutron Stars

In confined hadronic matter, the spontaneous breaking and restoration of chiral symmetry can be described by considering nucleons, 𝑁 + ⁡(939), and excited states of opposite parity, 𝑁 − ⁡(1535). In a cold, dense hadronic phase where chiral symmetry remains spontaneously broken, direct Urca decay processes involving the 𝑁 − are possible, e.g., 𝑁 − → 𝑁 + + 𝑒 − + $\bar{𝜈}_𝑒$. Here, we show that at low temperature and moderate densities, because the 𝑁 − are much heavier than the 𝑁 + , such cooling dominates over standard 𝑁 + direct Urca processes. This provides a strong astrophysical signature of the pattern of chiral symmetry restoration in neutron stars.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2021

Investigating the relationship between radial pre-stress magnitude and ballistic projectile dwell in heavy confined ceramic targets

A series of bare silicon carbide ceramic armour disks were manufactured with high-strength steel containment to induce varying magnitudes of radial pre-stress. The induced radial stresses, ranging from 0 to 900 MPa, were measured via neutron diffraction and verified by comparison with numerical calculations. Four targets of each configuration, referred to as slip-fit, moderate pre-stress, and high pre-stress, were subject to ballistic testing with hemispherical-nose, tungsten heavy alloy long rod projectiles to determine the interface defeat transition velocity. In-situ diagnostics were unsuccessful in aiding the identification of interface defeat, necessitating a reliance on post-mortem assessment. A transition velocity of approx. 1000 m/s was identified for the unstressed target, increasing to approx. 1200 m/s for the pre-stressed configurations. No performance effect was discernible between the moderate (372 MPa) and high (899 MPa) pre-stress configurations, suggesting that an optimal performance may be achieved for lower pre-stress levels (i.e., <372 MPa). Additionally, the test results were compared with four semi-analytical predictions of interface defeat performance and good agreement was found, albeit with significant range in the model predictions.

42 ENGINEERING↗

DOE OSTI2024

Towards the Development of Molten Salt Reactor Multiphysics Modeling Capabilities: Depletion, Thermochemistry, Reactor Dynamics, and Species Tracking

This report documents the simulation and modeling work performed under the Nuclear Energy Advanced Modeling and Simulation (NEAMS) program, utilizing the tools and codes developed under the program. The focus in this Fiscal Year (FY) is on the depletion, thermochemistry, reactor dynamics, and species transport in MSRs. The fission products travelling in the entire primary loop is unique in MSRs. There are many physical/chemical mechanisms that can significantly affect the fission products concentration in the fuel salt, e.g., diffusion into gas bubbles, diffusion in the core moderators, deposition on the surface of structures/pipes, etc. The fission product concentration in the fuel salt can potentially affect the neutronics, system dynamics, chemical potentials, etc., so accurately predicting the fission products distribution in the primary loop is important. Under the main objective, different activities are pursued to assess the NEAMS tools applicability for a variety of areas on species transport, including the depletion analyses using Griffin (fission product source), the redox potential assessment at different depletion points, the assessment of xenon transport effect on the neutronics and reactor dynamics, a survey of correlations for calculating the mass transfer coefficient of different fission products, etc.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2023

Microstructural characterization of nuclear graphite: from the microscale to the nanoscale

Multiple reactor designs use graphite as a moderator of the nuclear reactions and as structural support. During the lifetime of the reactor, multiple aging factors such as neutron irradiation, oxidation, and temperature along with others induce changes in the microstructure and crystal lattice of graphite components. The pore morphology and crystal structure of some phases in graphite can be used to trace the evolution of irradiation defects and mechanical properties of graphite. We present a combination of results from several microscopy techniques to investigate the differences between nuclear graphite grades and the effects of neutron irradiation and oxidation at multiple length scales. This multiscale approach is needed to understand the microstructural variations caused by the raw materials and manufacturing processes as well as how the different phases of graphite are affected by the reactor environment. The results provide insight into the oxidation- and radiation-induced changes of graphite and create a robust baseline of microstructure information that can be used for the selection of materials for the next generation of nuclear power stations. Moreover, the experiments conducted in this work provide an overview of the advantages and limitations of the most common techniques used to characterize nuclear graphite and how these techniques might be applied to study other carbon-based materials used in the nuclear industry.

Arregui Mena, Jose'↗

DOE OSTI2023

Multiphysics Pebble-Bed Reactor Control Rod Withdrawal Study

This work studied the responses of both a generic gas- and a fluoride-cooled PBR concept---the gPBR-200 and gFHR, respectively---during reactivity insertion accidents. Both models rely on 2-D axisymmetric simulations to solve the neutron flux distribution, nuclide concentrations, and temperature across the core---in addition to numerous representative pebble and TRISO particle simulations for determining fuel and moderator temperatures. This not only allows for computing maximum temperatures in the core---thus enabling estimation of how near the fuel is to peak operational and safety limits---as prescribed by specified acceptable fuel design limits, which are determined in such a way that fuel is not damaged during operational or anticipated abnormal occurrences---but also predicting how much of the core exceeds a given temperature limit, as well as determining the local energy deposition rate. These models consider both control rod withdrawal and ejection events. The former introduces a great deal more reactivity, as all the control rods are withdrawn (as opposed to a single one in the latter case), though at a much slower pace. In addition, for the gPBR-200, two limiting cases were considered: one with the core starting under hot full-power conditions and one with it starting under cold zero-power conditions. While the amount of reactivity added in the latter case is much higher (due to the far lower temperatures and the lack of neutron poisons such as Xe-135), the margin to temperature limits is also much more significant. Overall, for the design considered, none of the accidents resulted in the maximum fuel temperature reaching values close to the TRISO limit. However, the methodology presented herein could be very relevant if some designs consider reduced margins (e.g., higher temperatures) to achieve enhanced economics. Further model improvement is needed to better capture control rod worth, both in terms of cusping effects (as the rods are slowly withdrawn) and differential worth, especially as the tips of the rods near the upper cavity.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2022

Sensitivity and uncertainty analysis of PWR spent fuel observables to operational and model parameters

Sensitivity and uncertainty analyses of spent nuclear fuel (SNF) observables - decay heat, neutron and γ-ray emission rate - to operational and model parameters have been performed. A 2D model representing a typical PWR 17x17 UO{sub 2} fuel assembly has been taken as reference. The Serpent code and ENDF/B-VII.1 evaluated nuclear data library have been used for the analyses. Relative uncertainty of decay heat, neutron and γ-ray emission rates due to Monte Carlo counting statistics, as well as the number of fuel pin radial regions required for an accurate characterization of SNF neutron emission, have been estimated. A parametric study has been carried out to investigate the impact of the homogenization to an average value of the fuel and moderator temperature, boron concentration power and burnup on the prediction of the selected observables. In addition, linear sensitivity coefficients have been calculated. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2020

Nuclear Criticality Safety Assessment of Criticality Control Containers without Moderation Control at the Waste Isolation Pilot Plant

The Waste Isolation Pilot Plant (WIPP) provides for safe, permanent disposal of government-owned transuranic (TRU) and TRU mixed wastes. Receipt and disposal of waste at the WIPP site began in March 1999. The Sandia report, Consideration of Nuclear Criticality When Disposing of Transuranic Waste at the Waste Isolation Pilot Plant, addressed potential nuclear criticality safety issues based on the projected inventory characteristics known at the time [1]. As designs for inventory, waste forms, and disposal packages have changed, new analyses have been performed, and updates have been made to address any potential effects to the WIPP safety basis. New analyses performed include Saylor 2017 [2] and Brickner 2019 [3], which address certain waste containers with specified loadings under post-closure conditions. Both examined several hypothetical scenarios and included analyses to bound (from a criticality potential standpoint) credible configurations that could occur at WIPP during the repository regulatory post-closure disposal time period for feature, event, and process (FEP) considerations—10,000 years. During this post-closure period at WIPP, the screening of FEPs is governed by the risk-based standards and implementing regulations of the US Environmental Protection Agency (EPA) (i.e., 40 CFR 191 and 40 CFR 194, respectively) [4,5]. An FEP screening can be based on either a low-consequence or low-probability rationale. A low-probability rationale includes either (a) a qualitative rationale that the FEP is not credible or (b) a quantitative demonstration that the probability is less than 10-4 in 104 years. In this evaluation, a qualitative lowprobability rationale of not credible is used by demonstrating that bounding configurations of the waste are not critical. The demonstration of subcriticality is through quantitative calculations, but a probability of criticality is not evaluated. Rather, the rationale for this evaluation is that bounding configurations with an effective neutron multiplication factor (keff) well below the upper subcriticality limit (USL) make criticality incredible. Reference [2] documented a nuclear criticality assessment of the WIPP repository for disposal of dilute surplus plutonium materials using the Dilute and Dispose Approach and packaging in criticality control overpacks (CCOs). The CCO is the waste disposal container recently designed to allow for up to 380 fissile gram equivalent (FGE) 239 Pu per drum, which is a higher fissile loading than typical waste containers. The CCO consists of a criticality control container (CCC) positioned by upper and lower plywood spacers within a standard 55 gal drum. The CCC is used to establish a geometry control for fissile materials during transportation and WIPP emplacement operations. The current WIPP waste acceptance criteria for CCO payloads limit beryllium to less than or equal to 1% by weight of the waste contents and require the waste form to be non-machine compacted. Reference [2] considered two scenario progressions—room closure from salt creep, hereafter referred to as the reconfigured dry scenario, and flooding with brine, hereafter referred to as the reconfigured wet scenario. The subsequent drying out of the reconfigured wet scenarios was also considered. For all scenarios, subcriticality was maintained when 50 g of B 4 C (acting as a neutron absorber) per CCC was intermixed within the plutonium disposition waste form. The analysis used a waste form description that limits the amount of moderation that could be present within the waste form (i.e., it limits the amount of water and polyethylene that could be present based on planned processing conditions). This analysis to evaluate increased limits on the amount of moderation that could be present was performed as a companion to Reference [2] to address concerns associated with verifying moisture and/or plastic contents of waste materials following packaging of dilute surplus plutonium in the CCO. To that end, this analysis used the models and methods from Reference [2] to evaluate a more generic base waste form consisting of water and polyethylene that is more similar (and nearly identical) to the generic waste forms utilized in other models/analyses supporting the TRU Package Transporter Model II (TRUPACTII) safety analysis [6] (all are without moderation controls). The waste form in this analysis uses a base mixture of 75% water and 25% polyethylene, the total amount of which is varied to determine the optimum moderation to fissile material (H/Pu) ratio. The fissile loading is maintained at up to 380 FGE 239 Pu (modeled as PuO 2 ) per CCO with an additional 545 g of beryllium (to bound the 1% by weight contents restriction) and 50 g of B 4 C intermixed per CCO. The beryllium content (1% by weight) is based on the total allowed waste weight (this does not include packaging and container weights). Figures ES-1 and ES-2 display summary results, showing that with this model including 50 g of B 4 C per CCO, the system keff remains under 0.85 for all moderator amounts and provides a significant margin against post-closure criticality under postulated bounding conditions for compaction. Figure ES-1 compares an infinite model with a room model at the initial emplacement spacing and under full radial compaction. Full radial compaction places each CCC in direct contact and does not credit any anticipated spacing associated with current post-closure geomechanical modeling of the repository [7]. The effects of variations in the H/Pu ratio were evaluated by varying the amount of the water/polyethylene component of the waste model, with fissile loading maintained at 380 239 Pu FGE. Similarly, Figure ES-2 illustrates how various amounts of B 4 C per CCO influence k eff at different radial compactions, all at the H/Pu ratio of 200 (in the room array model). Therefore, while the results from Saylor 2017 [2] modeled more realistic process limits associated with packaging of dilute surplus plutonium, this analysis demonstrates that limits on moderation (plastic and water content) are not necessary to ensure subcriticality in the WIPP repository, provided the requisite B 4 C absorber is present.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2020

MPACT Verification With Magnox Reactor Neutronics Progression Problems

MPACT is a state-of-the-art core simulator designed to perform high-fidelity analysis using whole-core, three-dimensional, pin-resolved neutron transport calculations on modern parallel computing hardware. MPACT was originally developed to model light water reactors, and its capabilities are being extended to simulate gas-cooled, graphite-moderated cores such as Magnox reactors. To verify MPACT’s performance in this new application, the code is being formally benchmarked using representative problems. Progression problems are a series of example models that increase in complexity designed to test a code’s performance. The progression problems include both beginning-of-cycle and depletion calculations. Reference solutions for each progression problem have been generated using Serpent 2, a continuous-energy Monte Carlo reactor physics burnup calculation code.Using the neutron multiplication eigenvalue ke as a metric, MPACT’s performance is assessed on each of the progression problems. Initial results showed that MPACT’s multi-group cross section libraries, originally developed for pressurized water reactor problems, were not sufficient to accurately solve Magnox problems. MPACT’s improved performance on the progression problems is demonstrated using this new optimized cross section library.

Luciano, Nicholas↗

DOE OSTI2023

TEX-HEU Baseline Assemblies: Highly Enriched Uranium Plates with Polyethylene Moderator and Polyethylene Reflector (IER-297 CED-4b Report)

This experiment provides the baseline experimental configurations for TEX-HEU. The purpose of the TEX-HEU design is to provide multiple configurations that span the entire neutron energy spectrum and can be easily modified to incorporate diluent materials. Future experiments utilizing the TEX-HEU design are planned to incorporate hafnium, lithium, and chlorine as diluent materials. Five experimental configurations were judged to be acceptable critical benchmark experiments.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗