Search NASA⌕ Search

SEARCH · Search NASA

Results for “numerical simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Coupled numerical simulation of the external and engine inlet flows for the F-18 at large incidence

This paper presents a numerical simulation of the external and engine inlet flows for the F-18 aircraft at typical high-angle-of-attack flight conditions. Two engine inlet mass flow rates, corresponding to flight idle and maximum power, were computed. This was accomplished using a structured, overset grid technique to couple the external and internal grid systems. Reynolds-averaged Navier-Stokes solutions were obtained using an implicit, finite-differencing scheme. Results show a strong coupling of the external and engine inlet flows, especially at the maximum power setting. Increasing the mass flow rate through the inlet caused the primary vortex breakdown location to move downstream. This trend is also observed in flight tests performed on the F-18. A reversed flow region upstream of the inlet duct is visible in the faired-inlet and flight-idle computations. This flow reversal is not present in the maximum power setting computation. These large-scale changes in flow structure highlight the importance of simulating inlet conditions in high-angle-of-attack aircraft computations.

Murman, Scott M.↗
NASA NTRS1993

Surrogates for numerical simulations; optimization of eddy-promoter heat exchangers

Although the advent of fast and inexpensive parallel computers has rendered numerous previously intractable calculations feasible, many numerical simulations remain too resource-intensive to be directly inserted in engineering optimization efforts. An attractive alternative to direct insertion considers models for computational systems: the expensive simulation is evoked only to construct and validate a simplified, input-output model; this simplified input-output model then serves as a simulation surrogate in subsequent engineering optimization studies. A simple 'Bayesian-validated' statistical framework for the construction, validation, and purposive application of static computer simulation surrogates is presented. As an example, dissipation-transport optimization of laminar-flow eddy-promoter heat exchangers are considered: parallel spectral element Navier-Stokes calculations serve to construct and validate surrogates for the flowrate and Nusselt number; these surrogates then represent the originating Navier-Stokes equations in the ensuing design process.

Patera, Anthony T.↗
NASA NTRS1993

Rocket engine numerical simulation

The topics are presented in view graph form and include the following: a definition of the rocket engine numerical simulator (RENS); objectives; justification; approach; potential applications; potential users; RENS work flowchart; RENS prototype; and conclusions.

Davidian, Ken↗
NASA NTRS1995

Rapid Numerical Simulation of Viscous Axisymmetric Flow Fields

A two-dimensional Navier-Stokes code has been developed for rapid numerical simulation of axisymmetric flow fields, including flow fields with an azimuthal velocity component. The azimuthal-invariant Navier-Stokes equations in a cylindrical coordinate system are mapped to a general body-fitted coordinate system, with the streamwise viscous terms then neglected by applying the thin-layer approximation. Turbulence effects are modeled using an algebraic model, typically the Baldwin-Lomax turbulence model, although a modified Cebeci-Smith model can also be used. The equations are discretized using central finite differences and solved using a multistage Runge-Kutta algorithm with a spatially varying time step and implicit residual smoothing. Results are presented for calculations of supersonic flow over a waisted body-of-revolution, transonic flow through a normal shock wave in a straight circular duct of constant cross sectional area, swirling supersonic (inviscid) flow through a strong shock in a straight radial duct, and swirling subsonic flow in an annular-to-circular diffuser duct. Comparisons between computed and experimental results are in fair to good agreement, demonstrating that the viscous code can be a useful tool for practical engineering design and analysis work.

Tweedt, Daniel L.↗
NASA NTRS2003

Numerical Simulation of Event 191-6 of NASA's Flight Tests

In this viewgraph presentation, information is provided on the numerical simulation of a turbulence event encountered by NASA Langley's B-757 while conducting flight tests in areas at high risk for severe turbulence. Specific details on the Terminal Area Simulation System (TASS) show how the simulation is devised. The 100 m simulation was able to observe large-scale features.

Proctor, Fred H.↗
NASA NTRS2015

Numerical Simulation of Liquid Nitrogen Chilldown of a Vertical Tube

This paper presents the results of a one-dimensional numerical simulation of the transient chilldown of a vertical stainless steel tube with liquid nitrogen. The direction of flow is downward (with gravity) through the tube. Heat transfer correlations for film, transition, and nucleate boiling, as well as critical heat flux, rewetting temperature, and the temperature at the onset of nucleate boiling were used to model the convection to the tube wall. Chilldown curves from the simulations were compared with data from 55 recent liquid nitrogen chilldown experiments. With these new correlations the simulation is able to predict the time to rewetting temperature and time to onset of nucleate boiling to within 25% for mass fluxes ranging from 61.2 to 1150 kg/(sq m s), inlet pressures from 175 to 817 kPa, and subcooled inlet temperatures from 0 to 14 K below the saturation temperature.

GFSSP↗
NASA NTRS1993

Numerical simulation of three-dimensional self-gravitating flow

The three-dimensional flow of a self-gravitating fluid is numerically simulated using a Fourier pseudospectral method with a logarithmic variable formulation. Two cases with zero total angular momentum are studied in detail, a 323 simulation (Run B). Other than the grid size, the primary difference between the two cases are that Run A modeled atomic hydrogen and had considerably more compressible motion initially than Run B, which modeled molecular hydrogen. The numerical results indicate that gravitational collapse can proceed in a variety of ways. In the Run A, collapse led to an elongated tube-like structure, while in the Run B, collapse led to a flatter, disklike structure.

Shebalin, John V.↗
NASA NTRS1994

Numerical simulation of three-dimensional self-gravitating flow

The three-dimensional flow of a self-gravitating fluid is numerically simulated using a Fourier pseudospectral method with a logarithmic variable formulation. Two cases with zero total angular momentum are studied in detail, a 32(exp 3) simulation (Run A) and a 64(exp 3) simulation (Run B). Other than the grid size, the primary differences between the two cases are that Run A modeled atomic hydrogen and had considerably more compressible motion initially than Run B, which modeled molecular hydrogen. ('Compressible motion' is that part of the velocity which has zero curl, but non-zero divergence). The numerical results indicate that gravitational collapse can proceed in a variety of ways. In Run A, collapse led to an elongated tube-like structure, while in Run B, collapse led to a flatter, disk-like structure.

Shebalin, J. V.↗
NASA NTRS2003

Numerical Simulations of STOVL Hot Gas Ingestion in Ground Proximity Using a Multigrid Solution Procedure

A multi grid solution procedure for the numerical simulation of turbulent flows in complex geometries has been developed. A Full Multigrid-Full Approximation Scheme (FMG-FAS) is incorporated into the continuity and momentum equations, while the scalars are decoupled from the multi grid V-cycle. A standard kappa-Epsilon turbulence model with wall functions has been used to close the governing equations. The numerical solution is accomplished by solving for the Cartesian velocity components either with a traditional grid staggering arrangement or with a multiple velocity grid staggering arrangement. The two solution methodologies are evaluated for relative computational efficiency. The solution procedure with traditional staggering arrangement is subsequently applied to calculate the flow and temperature fields around a model Short Take-off and Vertical Landing (STOVL) aircraft hovering in ground proximity.

Wang, Gang↗
NASA NTRS1988

Studying Turbulence Using Numerical Simulation Databases, 2. Proceedings of the 1988 Summer Program

The focus of the program was on the use of direct numerical simulations of turbulent flow for study of turbulence physics and modeling. A special interest was placed on turbulent mixing layers. The required data for these investigations were generated from four newly developed codes for simulation of time and spatially developing incompressible and compressible mixing layers. Also of interest were the structure of wall bounded turbulent and transitional flows, evaluation of diagnostic techniques for detection of organized motions, energy transfer in isotropic turbulence, optical propagation through turbulent media, and detailed analysis of the interaction of vortical structures.

Source record↗
NASA NTRS1990

A study of the topology of dissipating motions in direct numerical simulations of time-developing compressible and incompressible mixing layers

A preliminary investigation of the geometry of flow patterns in numerically simulated compressible and incompressible mixing layers was carried out using 3-D critical point methodology. Motions characterized by high rates of kinetic energy dissipation and/or high enstrophy were of particular interest. In the approach the partial derivatives of the velocity field are determined at every point in the flow. These are used to construct the invariants of the velocity gradient tensor and the rate-of-strain tensor (P, Q, R, and P(sub s), Q(sub s), R(sub s) respectively). For incompressible flow the first invariant is zero. For the conditions of the compressible simulation, the first invariant is found to be everywhere small, relative to the second and third invariants, and so in both cases the local topology at a point is mainly determined by the second and third invariants. The data at every grid point is used to construct scatter plots of Q versus R and Q(sub s) versus R(sub s). Most points map to a cluster near the origin in Q-R space. However, fine scale motions, that is motions which are characterized by velocity derivatives which scale with the square root of R(sub delta), tend to map to regions which lie far from the origin. Definite trends are observed for motions characterized by high enstrophy and/or high dissipation. The observed trends suggest that, for these motions, the second and third invariants of the velocity gradient and rate-of-strain tensors are strongly correlated. The second and third invariants of the rate-of-strain tensor are related by K(-Q(sub s))(exp 3/2), which is consistent with the above scaling of velocity derivatives. The quantity K appears to depend on Reynolds number with an upper limit K = 2(the square root of 3)/9 corresponding to locally axisymmetric flow. For both the compressible and incompressible mixing layer, regions corresponding to high rates of dissipation are found to be characterized by comparable magnitudes of R(sub ij)R(sub ij) and S(sub ij)S(sub ij). For the incompressible mixing layer, regions characterized by the highest values of enstrophy are found to have relatively low strain rates.

Chen, J. H.↗
NASA NTRS1992

Numerical simulation of fluid flow and heat transfer in a thin liquid film over a rotating disk

The results of a numerical simulation of the flow field and associated heat transfer coefficient are presented for the free surface flow of a thin liquid film adjacent to a horizontal rotating disk. The computation has been performed for different flow rates and rotational velocities using a three-dimensional boundary-fitted coordinate system. Since the geometry of the free surface is unknown and dependent on flow rate, rate of rotation, and other parameters, an interative procedure had to be used to ascertain its location. The computed film height agreed well with existing experimental measurements. The flow was dominated by inertia near the entrance and close to the free surface, and dominated by centrifugal force at larger radii and adjacent to the disk. The rotation enhanced the heat transfer coefficient by a significant amount.

Rahman, M. M.↗
NASA NTRS1994

Numerical simulation of large-scale field-aligned current generation from finite-amplitude magnetosonic waves

A two-dimensional numerical simulation of finite-amplitude magnetohydrodynamic (MHD) magnetosonic waves is performed under a finite-velocity background convection condition. Isothermal cases are considered for simplicity. External dissipation is introduced by assuming that the field-aligned currents are generated in proportion to the accumulated charges. The simulation results are as follows: Paired field-aligned currents are found from the simulated waves. The flow directions of these field-aligned currents depend on the angle between the background convection and the wave normal, and hence two pairs of field-aligned currents are found from a bowed wave if we look at the overall structure. The majority of these field-aligned currents are closed within each pair rather than between two wings. These features are not observed under slow background convection. The result could be applied to the cusp current system and the substorm current system.

Yamauchi, M.↗
NASA NTRS1997

Efficient Parallel Algorithm For Direct Numerical Simulation of Turbulent Flows

A distributed algorithm for a high-order-accurate finite-difference approach to the direct numerical simulation (DNS) of transition and turbulence in compressible flows is described. This work has two major objectives. The first objective is to demonstrate that parallel and distributed-memory machines can be successfully and efficiently used to solve computationally intensive and input/output intensive algorithms of the DNS class. The second objective is to show that the computational complexity involved in solving the tridiagonal systems inherent in the DNS algorithm can be reduced by algorithm innovations that obviate the need to use a parallelized tridiagonal solver.

Moitra, Stuti↗
NASA NTRS2019

Investigation of Transitional Shock-Wave/Boundary Layer Interactions Using Direct Numerical Simulations

Interaction of a transitional boundary layer with a normal-shock is investigated using unstructured tetrahedral meshes under the numerical framework of the space-time conservation element, solution element (CESE) method. The computations mimic recent experimental efforts at the University of Tennessee Space Institute, where a Mach 2.0 flow interacts with a tall cylinder attached to a flat plate. The location of the cylinder with respect to the flat plate leading edge determines if the incoming boundary layer is laminar, transitional or fully turbulent. Four representative flow conditions exemplifying laminar and transitional boundary layers are analyzed by direct numerical simulations. Similar to what was observed in the experiments for the case of transitional interaction, the computations reveal an intermittent upstream influence (UI) shock that repeatedly travels upstream from the lambda-foot toward the leading edge before vanishing. Through detailed unsteady flow analysis obtained using Fourier analysis and dynamic mode decomposition techniques, the presence of disturbances with similar frequencies as those measured in experiments were identified in the flow along with locations that appear to influence the dynamics of the flow.

Venkatachari, Balaji Shankar↗
NASA NTRS2015

Utilizing Direct Numerical Simulations of Transition and Turbulence in Design Optimization

Design optimization methods that use the Reynolds-averaged Navier-Stokes equations with the associated turbulence and transition models, or other model-based forms of the governing equations, may result in aerodynamic designs with actual performance levels that are noticeably different from the expected values because of the complexity of modeling turbulence/transition accurately in certain flows. Flow phenomena such as wake-blade interaction and trailing edge vortex shedding in turbines and compressors (examples of such flows) may require a computational approach that is free of transition/turbulence models, such as direct numerical simulations (DNS), for the underlying physics to be computed accurately. Here we explore the possibility of utilizing DNS data in designing a turbine blade section. The ultimate objective is to substantially reduce differences between predicted performance metrics and those obtained in reality. The redesign of a typical low-pressure turbine blade section with the goal of reducing total pressure loss in the row is provided as an example. The basic ideas presented here are of course just as applicable elsewhere in aerodynamic shape optimization as long as the computational costs are not excessive.

Direct numerical simulations of transition and tur↗
NASA NTRS1993

Numerical simulations of three-dimensional laminar flow over a backward facing step; flow near side walls

This paper reports the results of numerical simulations of steady, laminar flow over a backward-facing step. The governing equations used in the simulations are the full 'compressible' Navier-Stokes equations, solutions to which were computed by using a cell-centered, finite volume discretization. The convection terms of the governing equations were discretized by using the Advection Upwind Splitting Method (AUSM), whereas the diffusion terms were discretized using central differencing formulas. The validity and accuracy of the numerical solutions were verified by comparing the results to existing experimental data for flow at identical Reynolds numbers in the same back step geometry. The paper focuses attention on the details of the flow field near the side wall of the geometry.

Steinthorsson, Erlendur↗
DOE OSTI2024

Numerical simulation projects in micromagnetics with Jupyter

We report a case study where an existing materials science course was modified to include numerical simulation projects on the micromagnetic behavior of materials. The Ubermag micromagnetic simulation software package is used in order to solve problems computationally. The simulation software is controlled through the Python code in Jupyter notebooks. Our experience is that the self-paced problem-solving nature of the project work can facilitate a better in-depth exploration of the course contents. We discuss which aspects of the Ubermag and the project Jupyter ecosystem have been beneficial for the students' learning experience and which could be transferred to similar teaching activities in other subject areas.

97 MATHEMATICS AND COMPUTING↗