SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The most optimal design for a chemical propellant, manned OTV that fulfills the described constraints is presented. The design of the Project Orion OTV and its subsystems are examined.
The drag parachute system was added to the Space Shuttle Orbiter's landing deceleration subsystem beginning with flight STS-49 in May 1992. The addition of this subsystem to an existing space vehicle required a detailed set of ground tests and analyses. The aerodynamic design and performance testing of the system consisted of wind tunnel tests, numerical simulations, pilot-in-the-loop simulations, and full-scale testing. This analysis and design resulted in a fully qualified system that is deployed on every flight of the Space Shuttle.
The orbital debris environment model is intended to be used by the spacecraft community for the design and operation of spacecraft in low Earth orbit. This environment, when combined with material-dependent impact tests and spacecraft failure analysis, is intended to be used to evaluate spacecraft vulnerability, reliability, and shielding requirements. The environment represents a compromise between existing data to measure the environment, modeling of this data to predict the future environment, the uncertainty in both measurements and modeling, and the need to describe the environment so that various options concerning spacecraft design and operations can be easily evaluated.
A breadboard radar system is being designed and tested at NASA Johnson for dealing with the space debris problem that could present a growing threat to Space Station Freedom. The major design problems are due to the small radar cross section of such debris (below -30 dBm2), the high closing velocities of the particles with respect to the Space Station (10 km/sec and higher), and the stringent weight, power-consumption, maintenance, and reliability constraints on spaceborne systems. Consideration is given to the preliminary implementation of a ground demonstration radar for testing concepts, technologies, and performance envelopes for application to the space-borne debris detection and tracking radar. Simulation results and techniques developed for predicting system performance and for evaluating antenna parameters are given. The design process of the electronically steered phased array antenna is briefly described, and block diagrams for the implementation of the radar system are given.
Orbiting solar telescope design for solar disturbances location and monitoring in H alpha line
A trade-off analysis between maneuver period, execution errors, and orbit determination uncertainties is carried out for the Ocean Topography Experiment spacecraft for a given nodal equatorial constraint. Semimajor axis and eccentricity are controlled with minimum impulse using the linear theory of optimal transfer between close coplanar near-circular orbits. Ellipses of equal minimum and average maneuver periods are presented in the (3 execution error, 3 orbit determination uncertainty) space for different nodal equatorial constraints enabling the determination of the appropriate combination of execution errors and orbit determination uncertainties that guarantees a mission required minimum maneuver period for a given nodal deadband.
Once in science mission orbits, the four 0.12-km diameter observatories plan to form a tetrahedron with as little as 4-km of separation between spacecraft. The stated operational goal of maneuvering the fleet is no more often than once every two weeks (on average). Derived maneuvering accuracy requirement levied on the ACS
The NISAR mission plans to use a 12-day-repeating sun-synchronous orbit for repeat-pass interferometry at multiple time scales using SAR data. For the interferometry to work the radar measurements must be made from within a critical baseline, which happens if all of the orbits are maintained to be within a fixed tube around a reference orbit. This paper describes the choice of dynamical models used in defining such a reference orbit, the perturbative effects of dynamics not considered in the repeat orbit, and the process of designing the orbit to repeat. We also describe our method for sharing the repeat orbit among multiple mission participants who use different models and software.
The NISAR mission plans to use a 12-day-repeating sun-synchronous orbit for repeat-pass interferometry at multiple time scales using SAR data. For the interferometry to work the radar measurements must be made from within a critical baseline, which happens if all of the orbits are maintained to be within a fixed tube around a reference orbit. This paper describes the choice of dynamical models used in defining such a reference orbit, the perturbative effects of dynamics not considered in the repeat orbit, and the process of designing the orbit to repeat. We also describe our method for sharing the repeat orbit among multiple mission participants who use different models and software.
Replacement of failed or worn-out equipment while the satellite remains on-orbit is considered. Factors discussed include: modular construction of the satellite components, design of the service unit, and control of the service unit.
Preliminary design considerations and changes made in the baseline space shuttle orbital maneuvering system (OMS) to reduce cost and weight are detailed. The definition of initial subsystem requirements, trade studies, and design approaches are considered. Design features of the engine, its injector, combustion chamber, nozzle extension and bipropellant valve are illustrated and discussed. The current OMS consists of two identical pods that use nitrogen tetroxide (NTO) and monomethylhydrazine (MMH) propellants to provide 1000 ft/sec of delta velocity for a payload of 65,000 pounds. Major systems are pressurant gas storage and control, propellant storage supply and quantity measurement, and the rocket engine, which includes a bipropellant valve, an injector/thrust chamber, and a nozzle. The subsystem provides orbit insertion, circularization, and on orbit and deorbit capability for the shuttle orbiter.
The Viking Mission included the insertion of two unmanned spacecraft into orbit about Mars and the deployment of a soft-lander from each. A description is presented of the adaptive design and implementation of the spacecraft propulsive maneuvers as these flights progressed, taking into account also the inflight results for the orbital phase of the primary Viking mission. The design process included the selection of target parameters and the minimization of both propellant usage and the effects of execution errors, while complying with mission and operational constraints. All maneuvers performed to trim the spacecraft orbits are considered. Attention is given to navigation requirements, geometry definitions and terminology, maneuver mechanization and constraints, and maneuver capability.
The International Space Station (ISS) currently provides potable water dispensing for rehydrating crewmembers food and drinking packages with one system located in the United States On-orbit Segment (USOS) and one system in the Russian Segment. The USOS Potable Water Dispenser (PWD) was delivered to ISS on ULF2, Shuttle Mission STS-126, and was subsequently activated in November 2008. The PWD activation on ISS is capable of supporting an ISS crew of six but nominally supplies only half the crew. The PWD is designed to provide incremental quantities of hot and ambient temperature potable water to US style food packages. PWD receives iodinated water from the US Laboratory Fuel Cell Water Bus, which is fed from the Water Processing Assembly (WPA). The PWD removes the biocidal iodine to make the water potable prior to dispensing. A heater assembly contained within the unit supplies up to 2.0 liters of hot water (65 to 93oC) every thirty minutes. This quantity supports three to four crewmembers to rehydrate their food and beverages from this location during a single meal. The unit is designed to remain functional for up to ten years with replacement of limited life items such as filters. To date, the PWD on-orbit performance has been acceptable. Since activation of the PWD, there have been several differences between on-orbit functionality and expected performance of hardware design. The comparison of on-orbit functionality to performance of hardware design is outlined for the following key areas: microbiology, PWD to food package water leakage, no-dispense scenarios, under-dispense scenarios, and crewmember feedback on actual on-orbit use.
The International Space Station (ISS) currently provides potable water dispensing for rehydrating crewmember food and drinking packages. There is one system located in the United States On-orbit Segment (USOS) and one system in the Russian Segment. Shuttle mission STS-126 delivered the USOS Potable Water Dispenser (PWD) to ISS on ULF2; subsequent activation occurred on November 2008. The PWD is capable of supporting an ISS crew of six, but nominally supplies only half this crew size. The PWD design provides incremental quantities of hot and ambient temperature potable water to US food and beverage packages. PWD receives iodinated water from the US Water Recovery System (WRS) Fuel Cell Water Bus, which feeds from the Water Processing Assembly (WPA). The PWD removes the biocidal iodine to make the water potable prior to dispensing. A heater assembly contained within the unit supplies up to 2.0 L of hot water (65 to 93 ?C) every 30 min. During a single meal, this quantity of water supports three to four crewmembers? food rehydration and beverages. The unit design has a functional life expectancy of 10 years, with replacement of limited life items, such as filters. To date, the PWD on-orbit performance is acceptable. Since activation of the PWD, there were several differences between on-orbit functionality and expected performance of hardware design. The comparison of on-orbit functionality to performance of hardware design is discussed for the following key areas: 1) microbial contamination, 2) no-dispense and water leakage scenarios, and 3) under-dispense scenarios.
The systems and subsystems of the Space Telescope proposed for an orbiting observatory to be launched by the Space Shuttle in the 1980s are described. The structural design is simple and based on existing technologies for high reliability. Provisions are made for on-orbit servicing and maintenance. All deployable appendages are designed for manual override to insure retrieval and return of the Space Telescope to earth for major refurbishing, which should occur at intervals of not less than six years. Low performance risk, passive techniques are used in the thermal control subsystem to provide a cold-biased design with thermostatically controlled heaters to adjust temperature. The electrical power system utilizes NASA Standard Hardware - 50 ampere hour nickel-cadmium battery cells, a standard power regulator unit, and a flight-proven flexible rollup solar array with high-efficiency (12.5 per cent) silicon solar cells. The communication subsystem is designed for compatibility with the Tracking and Data Relay Satellite System. The pointing control system will have a maximum line of sight variation of 0.007 arc seconds. The telescope optics are a Ritchey-Chretien version of the Cassegrain configuration.
The design estimate for the materials for the International Space Station (ISS) specified in SSP 30512 was a conservative estimate. The environment dose was over estimated. The materials originally qualified for approximately 10-15 years are anticipated to be acceptable for periods of up to 20-30 years based on SSP-30512 or 40-60 years based on 2x SSP-30512. This viewgraph presentation shows charts and graphs that review the altitude, the solar minimum and maximum, and the radiation exposure of other satellite, among other graphics.
This paper is regarding a project in the Advanced Design Program at the University of Arizona. The project is named the Autonomous Space Processor for Orbital Debris (ASPOD) and is a NASA/Universities Space Research Association (USRA) sponsored design project. The development of ASPOD and the students' abilities in designing and building a prototype spacecraft are the ultimate goals of this project. This year's focus entailed the development of a secondary robotic arm and end-effector to work in tandem with an existent arm in the removal of orbital debris. The new arm features the introduction of composite materials and a linear drive system, thus producing a light-weight and more accurate prototype. The main characteristic of the end-effector design is that it incorporates all of the motors and gearing internally, thus not subjecting them to the harsh space environment. Furthermore, the arm and the end-effector are automated by a control system with positional feedback. This system is composed of magnetic and optical encoders connected to a 486 PC via two servo-motor controller cards. Programming a series of basic routines and sub-routines has allowed the ASPOD prototype to become more autonomous. The new system is expected to perform specified tasks with a positional accuracy of 0.5 cm.
Spacecraft system and subsystem designs at the conceptual level to perform either of two Mars Orbiter missions, a Climatology Mission and an Aeronomy Mission were developed. The objectives of these missions are to obtain and return data.