Search NASA⌕ Search

SEARCH · Search NASA

Results for “phase-locking”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

High-dynamic GPS tracking

The results of comparing four different frequency estimation schemes in the presence of high dynamics and low carrier-to-noise ratios are given. The comparison is based on measured data from a hardware demonstration. The tested algorithms include a digital phase-locked loop, a cross-product automatic frequency tracking loop, and extended Kalman filter, and finally, a fast Fourier transformation-aided cross-product frequency tracking loop. The tracking algorithms are compared on their frequency error performance and their ability to maintain lock during severe maneuvers at various carrier-to-noise ratios. The measured results are shown to agree with simulation results carried out and reported previously.

Hinedi, S.↗

A comparison of frequency estimation techniques for high-dynamic trajectories

A comparison is presented for four different estimation techniques applied to the problem of continuously estimating the parameters of a sinusoidal Global Positioning System (GPS) signal, observed in the presence of additive noise, under extremely high-dynamic conditions. Frequency estimates are emphasized, although phase and/or frequency rate are also estimated by some of the algorithms. These parameters are related to the velocity, position, and acceleration of the maneuvering transmitter. Estimated performance at low carrier-to-noise ratios and high dynamics is investigated for the purpose of determining the useful operating range of an approximate Maximum Likelihood (ML) estimator, an Extended Kalman Filter (EKF), a Cross-Product Automatic Frequency Control (CPAFC) loop, and a digital phase-locked loop (PPL). Numerical simulations are used to evaluate performance while tracking a common trajectory exhibiting high dynamics.

Vilnrotter, V. A.↗

Prototype laser-diode-pumped solid state laser transmitters

Monolithic, diode-pumped Nd:YAG ring lasers can provide diffraction-limited, single-frequency, narrow-linewidth, tunable output which is adequate for use as a local oscillator in a coherent communication system. A laser was built which had a linewidth of about 2 kHz, a power of 5 milliwatts, and which was tunable over a range of 30 MHz in a few microseconds. This laser was phase-locked to a second, similar laser. This demonstrates that the powerful technique of heterodyne detection is possible with a diode-pumped laser used as the local oscillator. Laser diode pumping of monolithic Nd:YAG rings can lead to output powers of hundreds of milliwatts from a single laser. A laser was built with a single-mode output of 310 mW. Several lasers can be chained together to sum their power, while maintaining diffraction-limited, single frequency operation. This technique was demonstrated with two lasers, with a total output of 340 mW, and is expected to be practical for up to about ten lasers. Thus with lasers of 310 mW, output of up to 3 W is possible. The chaining technique, if properly engineered, results in redundancy. The technique of resonant external modulation and doubling is designed to efficiently convert the continuous wave, infrared output of our lasers into low duty-cycle pulsed green output. This technique was verified through both computer modeling and experimentation. Further work would be necessary to develop a deliverable system using this technique.

Kane, Thomas J.↗

The use of interleaving for reducing radio loss in trellis-coded modulation systems

It is demonstrated how the use of interleaving/deinterleaving in trellis-coded modulation (TCM) systems can reduce the signal-to-noise ratio loss due to imperfect carrier demodulation references. Both the discrete carrier (phase-locked loop) and suppressed carrier (Costas loop) cases are considered and the differences between the two are clearly demonstrated by numerical results. These results are of great importance for future communication links to the Deep Space Network (DSN), especially from high Earth orbiters, which may be bandwidth limited.

Divsalar, D.↗

Advanced altimetry

The radar altimeter being developed for the Ocean Topography Experiment (TOPEX) will have an inherent instrument precision of 2 to 3 cm. While some minor refinements may be possible in the future, major geophysical advances could be made if altimetric measurements over a wide swath of the Earth's surface were possible. The NASA Headquarters Oceanic Processes Branch is supporting a 3-year investigation of the technological issues inherent in the precision measurement of topography from spaceborne platforms at angles off-nadir. To explore the off-nadir measurement of topography, a flexible, airborne radar instrument system is being developed. Its hardware design is now complete, and it is made up of several subsystems. The antenna selected is a dielectric lens of .894 m diameter. The RF subsystem uses phase-locked oscillators, FET solid-state amplifiers, and times four frequency multipliers to develop a transmit signal at a frequency of 36.0 GHz and a local oscillator signal at a frequency of 35.4 GHz. Lecroy 6880 digitizers under computer control digitize the five receiver outputs. The digital subsystem consists of six single-board Heurikon processors. At this time, the instrument construction continues with final system integration planned for November 1988.

Parsons, C. L.↗

Frequency estimation techniques for high dynamic trajectories

A comparison is presented of four different estimation techniques applied to the problem of continuously estimating the rapidly varying parameters of a sinusoidal signal, observed in the presence of additive noise. Frequency estimates are emphasized, although phase and/or frequency rate are also estimated by some of the algorithms. These parameters are related to the velocity, position, and acceleration of the maneuvering receiver or transmitter. Estimated performance at low carrier-to-noise ratios and high dynamics is investigated for the purpose of determining the useful operating range of an approximate maximum-likelihood estimator, an extended Kalman filter, a cross-product automatic frequency loop, and a phase-locked loop. Numerical simulations are used to evaluate performance while tracking a common trajectory exhibiting high dynamics.

Vilnrotter, Victor A.↗

Analog circuit for the measurement of phase difference between two noisy sine-wave signals

A simple circuit was designed to measure the phase difference between two noisy sine waves. It locks over a wide range of frequencies and produces an output proportional to the phase difference of rapidly varying signals. A square wave locked in frequency and phase to the first signal is produced by a phase-locked loop and is amplified by an operational amplifier.

Shakkottai, P.↗

The effects of sinusoidal interference on the second-order carrier tracking loop preceded by a bandpass limiter in the Block 4 receiver

Drop-lock relationships for the second-order phase-locked loop are derived when the carrier and a sinusoidal signal lie within the predetection filter bandwidth of the Block 4 receiver. Limiter suppression factors are calculated when a bandpass hard limiter is used to maintain constant total power at the loop. The parameters of interest are the interference-to-signal power ratio (ISR), the input signal-to-noise power ratio (NSR), and the interference signal frequency offset from carrier delta f. Limiter suppression caused by the combined effects of the noise and the interference signal accounts for the variability in the drop-lock threshold for given values of the input SNR and ISR parameters. Going beyond earlier published work that focused on the limiter's effect on the drop-lock threshold; an account is made for the limiter action in the interference mode and an overall imporvement is provided in the prediction accuracy of the drop-lock model.

Ruggier, C. J.↗

Slot clock recovery in optical PPM communication systems with avalanche photodiode photodetectors

Slot timing recovery in a direct-detection optical PPM communication system can be achieved by processing the photodetector output waveform with a nonlinear device whose output forms the input to a phase-locked loop. The choice of a simple transition detector as the nonlinearity is shown to give satisfactory synchronization performance. The rms phase error of the recovered slot clock and the effect of slot timing jitter on the bit error probability were directly measured. The experimental system consisted of an AlGaAs laser diode (wavelength = 834 nm) and a silicon avalanche photodiode photodetector. The system used Q = 4 PPM signaling and operated at a source data rate of 25 Mbits/s. The mathematical model developed to compute the rms phase error of the recovered clock is shown to be in good agreement with results of actual measurements of phase errors. The use of the recovered slot clock in the receiver resulted in no significant degradation in receiver sensitivity compared to a system with perfect slot timing. The system achieved a bit error probability of 10 to the -6th at a received optical signal energy of 55 detected photons per information bit.

Davidson, Frederic M.↗

Coherence properties of a doubly resonant monolithic optical parametric oscillator

A doubly resonant optical parametric oscillator (DRO) pumped with the second harmonic of a narrow-linewidth Nd:YAG laser is described. The linewidth of the DRO signal was less than 13 kHz, the DRO was shown to generate a phase-locked subharmonic of the pump at degeneracy, and the signal and the idler were shown to be mutually coherent with the pump and to be phase-anticorrelated with each other away from degeneracy. The signal-idler heterodyne linewidth was 500 Hz, and pump phase modulation was shown to transfer to the DRO phase at degeneracy.

Nabors, C. D.↗

Digital accumulators in phase and frequency tracking loops

Results on the effects of digital accumulators in phase and frequency tracking loops are presented. Digital accumulators or summers are used extensively in digital signal processing to perform averaging or to reduce processing rates to acceptable levels. For tracking the Doppler of high-dynamic targets at low carrier-to-noise ratios, it is shown through simulation and experiment that digital accumulators can contribute an additional loss in operating threshold. This loss was not considered in any previous study and needs to be accounted for in performance prediction analysis. Simulation and measurement results are used to characterize the loss due to the digital summers for three different tracking loops: a digital phase-locked loop, a cross-product automatic frequency tracking loop, and an extended Kalman filter. The tracking algorithms are compared with respect to their frequency error performance and their ability to maintain lock during severe maneuvers at various carrier-to-noise ratios. It is shown that failure to account for the effect of accumulators can result in an inaccurate performance prediction, the extent of which depends highly on the algorithm used.

Hinedi, Sami↗

The use of interleaving for reducing noisy reference loss in trellis-coded modulation systems

The use of interleaving/deinterleaving in trellis-coded modulation systems to reduce the SNR loss due to imperfect carrier demodulation references is demonstrated. Both the discrete carrier (phase-locked loop) and the suppressed carrier (Costas loop) cases are considered, and the differences between the two are clearly demonstrated by numerical results. The special case of convolutional codes is also treated and illustrated with an example of practical interest.

Divsalar, Dariush↗

Dual physiological rate measurement instrument

The object of the invention is to provide an instrument for converting a physiological pulse rate into a corresponding linear output voltage. The instrument which accurately measures the rate of an unknown rectangular pulse wave over an extended range of values comprises a phase-locked loop including a phase comparator, a filtering network, and a voltage-controlled oscillator, arranged in cascade. The phase comparator has a first input responsive to the pulse wave and a second input responsive to the output signal of the voltage-controlled oscillator. The comparator provides a signal dependent on the difference in phase and frequency between the signals appearing on the first and second inputs. A high-input impedance amplifier accepts an output from the filtering network and provides an amplified output DC signal to a utilization device for providing a measurement of the rate of the pulse wave.

Cooper, Tommy G.↗

Frame synchronization for a channel with different data rates

In some communication links, different data rates are used at different times on the same channel and each is assigned a separate frame synchronization (sync) marker. The frame search is completed within a finite number of frame intervals once both phase-lock and bit-sync are achieved because the incoming data rate can change. The probability of failure to frame-lock, and an upper bound of probability of false frame-lock in a frame search mode are derived for a communication link with a 10 to the -5th bit error probability. The probability of failure to detect data-rate change and the probability of false detection of data-rate change in a frame-lock mode are discussed. In a frame-lock mode, the probability of failure to detect data-rate change and probability detection of data-rate change an equal to 4.96 x 10 to the -12th. A frame-lock device can be used for the Space Station Freedom Ku-band return link.

Kwon, Hyuck M.↗

A Tone-Aided/Dual Vestigial Sideband (TA/DVSB) system for mobile satellite channels

Tone-aided modulation is one way of combatting the effects of multipath fading and Doppler frequency shifts. A new tone-aided modulation format for M-ary phase-shift keyed signals (MPSK) is discussed. A spectral null for the placement of the tone is created in the center of the MPSK signal by translating the upper sideband upwards in frequency by the same amount. The key element of the system is the algorithm for recombining the data sidebands in the receiver, a function that is performed by a specialized phase-locked loop (PLL). The system structure is discussed and simulation results showing the PLL acquisition performance are presented.

Saulnier, Gary J.↗

Software breadboard study

The overall goal of this study was to develop new concepts and technology for the Comet Rendezvous Asteroid Flyby (CRAF), Cassini, and other future deep space missions which maximally conform to the Functional Specification for the NASA X-Band Transponder (NXT), FM513778 (preliminary, revised July 26, 1988). The study is composed of two tasks. The first task was to investigate a new digital signal processing technique which involves the processing of 1-bit samples and has the potential for significant size, mass, power, and electrical performance improvements over conventional analog approaches. The entire X-band receiver tracking loop was simulated on a digital computer using a high-level programming language. Simulations on this 'software breadboard' showed the technique to be well-behaved and a good approximation to its analog predecessor from threshold to strong signal levels in terms of tracking-loop performance, command signal-to-noise ratio and ranging signal-to-noise ratio. The successful completion of this task paves the way for building a hardware breadboard, the recommended next step in confirming this approach is ready for incorporation into flight hardware. The second task in this study was to investigate another technique which provides considerable simplification in the synthesis of the receiver first LO over conventional phase-locked multiplier schemes and in this approach, provides down-conversion for an S-band emergency receive mode without the need of an additional LO. The objective of this study was to develop methodology and models to predict the conversion loss, input RF bandwidth, and output RF bandwidth of a series GaAs FET sampling mixer and to breadboard and test a circuit design suitable for the X and S-band down-conversion applications.

Nuckolls, C.↗

Space-qualified submillimeter radiometer

The purpose of this research was to develop a reliable submillimeter wave spectrometer for space-borne high frequency spectral line work. The emphasis was on improving the efficiency of frequency multipliers to limit the system components to rugged, low power consumption solid-state devices. This research has allowed Millitech to develop increased efficiency and performance in Millitech's existing line of submillimeter components and systems. Millitech has fabricated and tested a complete solid-state spectrometer front end for use at 560 GHz (the 1(sub 10) to 1(sub 01) transition of water vapor). The spectrometer was designed with the rigors of flight conditions in mind. The spectrometer uses a phase-locked, solid-state Gunn diode oscillator as the local oscillator, employing a tripler to produce about 3 mW of power at 285 GHz, and a low noise second harmonic waveguide mixer which requires less than 2 mW of LO power. The LO (and the signal) is injected into the mixer by means of a quasioptical diplexer. The measured system noise temperature is 2800 K (DSB) over 400 MHz. The whole spectrometer front end is compact (21 cm by 21 cm by 24 cm), light (7.4 kg), and has a power consumption of less than 8 W. Other topics explored in this work include compact frequency agile phase lock loops, optical filters, and InP Gunn oscillators for low noise applications. As a result of this research, the improvement in the design of multipliers and harmonic mixers will allow their use as the LO power for a variety of satellite-borne receivers operating in the 200 to 600 GHz frequency range.

Huguenin, G. R.↗

Small Business Innovations (MISER)

Lightwave Electronics Corporation, Mountain View, CA, developed the Series 120 and 122 non-planner diode pumped ring lasers based on a low noise ring laser with voltage tuning that they delivered to Jet Propulsion Laboratory under a Small Business Innovation Research (SBIR) contract. The voltage tuning feature allows "phase-locking" the lasers, making them "electronic," similar to radio and microwave electronic oscillators. The Series 120 and 122 can be applied to fiber sensing, coherent communications and laser radar.

Source record↗