Search NASA⌕ Search

SEARCH · Search NASA

Results for “polymer design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Rational Enzyme Design for Controlled Functionalization of Acetylated Xylan for Cell-Free Polymer Biosynthesis

Xylan O-acetyltransferase 1 (XOAT1) is involved in O-acetylating the backbone of hemicellulose xylan. Recent structural analysis of XOAT1 showed two unequal lobes forming a cleft that is predicted to accommodate and position xylan acceptors into proximity with the catalytic triad. Here, we used docking and molecular dynamics simulations to investigate the optimal orientation of xylan in the binding cleft of XOAT1 and identify putative key residues (Gln445 and Arg444 on Minor lobe & Asn312, Met311 and Asp403 on Major lobe) involved in substrate interactions. Site-directed mutagenesis coupled with biochemical analyses revealed the major lobe of XOAT1 is important for xylan binding. Mutation of single key residues yielded XOAT1 variants with various enzymatic efficiencies that are applicable to one-pot synthesis of xylan polymers with different degrees of O-acetylation. Taken together, our results demonstrate the effectiveness of computational modeling in guiding enzyme engineering aimed at modulating xylan and redesigning plant cell walls.

93 SC - Biological and Environmental Research (BER↗
DOE OSTI2021

Design of closed-loop recycling production of a Diels–Alder polymer from a biomass-derived difuran as a functional additive for polyurethanes

Acetalization of biomass-derived 5-hydroxymethyl furfural (HMF) with pentaerythritol produced a difuran (HPH) monomer in the presence of an acid catalyst. A recyclable polymer was then synthesized by Diels–Alder reaction of bismaleimide and the HMF-derived difuran (HPH). A polyurethane, produced from the Diels–Alder polymer has a higher glass transition temperature than a polyurethane, produced from ethylene glycol. The polyurethane, containing Diels–Alder polymer also has a self-healing ability. The Diels–Alder polymer could be hydrolyzed in acidic acetate buffer at 60 °C to produce the monomers for recycling. Each produced monomer was separated by solvent extraction, and the extracted monomers were recovered in different solvent fractions, such as aqueous, ethyl acetate, and acetone fractions. Techno economic analysis was used to assess the minimum selling price ($\$14.1$ per kg) for the primary production of Diels–Alder polymer at a feed capacity of 400 tons per year. The economic viability of the primary recovery process for the most expensive recovered monomer, bismaleimide, was assessed by calculating the minimum selling price of the bismaleimide ($\$15.2$ per kg). In conclusion, a circular closed-loop recycling production process for the Diels–Alder polymer was developed and this approach can produce the Diels–Alder polymer at $8.2 per kg when the feed capacity was 40 ktons per year.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Molecular dynamics simulations of energy accommodation between gases and polymers for ultra-low thermal conductivity insulation

Determining the energy accommodation between gases and solids is essential to developing porous thermal insulation materials with ultra-low effective thermal conductivity that reduce energy use, greenhouse gas emissions, and fossil fuel consumption. The energy accommodation coefficients of most gases, however, have been rarely studied, especially with respect to solids that have relatively high thermal resistivity, e.g., polymers. Here, by using all-atom nonequilibrium molecular dynamics simulations, we reveal the accommodation coefficients of He, Ar, N 2 , and O 2 with polymers, mainly polystyrene. We find that their values are around 0.51, 0.72, 0.79, and 0.90, respectively, suggesting a critical reexamination of the commonly used theoretical maximum value of 1. We have also conducted experiments and validated the value for air, which is about 0.81. Such a change in accommodation coefficients can lead to a reduction of about 70%, 50%, 35%, and 20% in the thermal conductivity of He, Ar, N 2 , and O 2 gases in nano pores (below 100 nm) or at low pressures (below 1 millibar). With these new accommodation coefficients, we find that in a 10 nm pore with ambient pressure at 300 K, the gas thermal conductivity of He, Ar, N 2 , and O 2 in porous polystyrene can be as low as 9.7 × 10 –4 , 3.4 × 10 –4 , 7.3 × 10 –4 , and 8.5 × 10 –4 W·m –1 ·K –1 , respectively, which are two to three orders of magnitude lower than their bulk values, promising higher thermal resistivity of insulation materials. This work reveals the fundamental energy exchange between gases and polymers, providing important guidance for designing high-performance thermal insulation materials for various applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Fast Photoactuation Driven by Supramolecular Polymers Integrated into Covalent Networks

Abstract The design of robotic soft matter capable of emulating the complex movements of living organisms such as mechanical actuation, shape transformation, and autonomous translation remains a grand challenge in soft materials science. Functionalized hydrogels are excellent candidates for such materials since they can operate in water and are highly responsive to their environment, but their response times can be slow. This work investigates fast photoactuation of hybrid bonding hydrogels composed of peptide amphiphile (PA) supramolecular nanofibers bonded covalently to merocyanine‐based (MCH + ) photoresponsive networks. By incorporating ionizable acrylic acid (AA) co‐monomers in these networks, photoactuation at nearly neutral pH is observed, which in turn enables a new mechanism to accelerate the response by triggering the bundling of supramolecular nanofibers by rapid proton exchange reactions. Furthermore, this rapid response and its consequent large shape transformations lead to hydrogels capable of spontaneously tracking external light sources inspired by pedicellariae, defensive organs present in echinoderms like the starfish and the sea urchin. This work suggests that hybrid bonding polymers (HBPs), which leverage the interplay between supramolecular assemblies and covalent networks, offer novel strategies to design rapidly actuating soft robotic materials.

Cezan, S. Doruk↗
DOE OSTI2024

TEAMER: Results of Investigating Structural Design Concepts and Alternative Materials for a Wave Power System

Included here are materials from a study on the design of a three-body Wave Energy Converter (WEC) utilizing a heave plate, dual Power Take Offs (PTOs), and single point mooring. A material trade study has been conducted to evaluate the effects of introducing various metallic and fiber-reinforced polymer (FRP) elements to the design. The baseline design is C-Power's patented k2 Wave Power System (WPS). This Testing Expertise and Access for Marine Energy Research (TEAMER) Request for Technical Support (RFTS) 9 effort resulted in alternative designs of the WPS center member, the nacelle. The analysis resulting from this study will inform the design of a lightweight structure with lower manufacturing and operating costs that increases energy conversion and power-to-weight ratio of the device. The dataset contains several components: finite element analysis (FEA) data, hand calculations, and CAD models. FEA files includes those used for and generated by finite element simulations. Calculations include hand calculations performed using Microsoft Excel, which assess core laminate properties, buckling, and other structural aspects in accordance with risk management DNV-RP-C201 standards. CAD materials include Solidworks files for parts, assemblies, and drawings of the evaluated models.

16 TIDAL AND WAVE POWER↗
DOE OSTI2023

Polymer Tacticity Effects in Polymer–Lanthanide Chelation Thermodynamics

Metal-chelating polymers are critical components in numerous applications. However, despite the known influence of polymer tacticity on both bulk and solution properties, most materials used in metal-chelation applications are atactic. Here, we investigate the relationship between polymer tacticity and polymer–lanthanide interactions in aqueous solution. We synthesized a series of five poly(methacrylic acid)s with systematic variations in tacticity (20–99% m diads) and used isothermal titration calorimetry to measure the thermodynamics of lanthanide binding to each material (ΔH, ΔG, ΔS, K a , and stoichiometry). We observed enthalpy–entropy compensation across this tacticity series, finding that both |ΔH| and |ΔS| decreased with decreasing m diad content while ΔG remained similar. Molecular dynamics simulations of the polymer–metal interactions revealed that the observed differences in binding thermodynamics may be largely ascribed to differences in polymer flexibility. Furthermore, these combined experimental and computational results demonstrate that metal binding can be influenced by altering the polymer stereochemistry, ultimately influencing the design of more efficient metal-chelating materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Comparing Zwitterionic and PEG Exteriors of Polyelectrolyte Complex Micelles

A series of model polyelectrolyte complex micelles (PCMs) was prepared to investigate the consequences of neutral and zwitterionic chemistries and distinct charged cores on the size and stability of nanocarriers. Using aqueous reversible addition-fragmentation chain transfer (RAFT) polymerization, we synthesized a well-defined diblock polyelectrolyte system, poly(2-methacryloyloxyethyl phosphorylcholine methacrylate)-block-poly((vinylbenzyl) trimethylammonium) (PMPC-PVBTMA), at various neutral and charged block lengths to compare directly against PCM structure–property relationships centered on poly(ethylene glycol)-block-poly((vinylbenzyl) trimethylammonium) (PEG-PVBTMA) and poly(ethylene glycol)-block-poly(l-lysine) (PEG-PLK). After complexation with a common polyanion, poly(sodium acrylate), the resulting PCMs were characterized by dynamic light scattering (DLS) and small angle X-ray scattering (SAXS). We observed uniform assemblies of spherical micelles with a diameter ~1.5–2× larger when PMPC-PVBTMA was used compared to PEG-PLK and PEG-PVBTMA via SAXS and DLS. In addition, PEG-PLK PCMs proved most resistant to dissolution by both monovalent and divalent salt, followed by PEG-PVBTMA then PMPC-PVBTMA. All micelle systems were serum stable in 100% fetal bovine serum over the course of 8 h by time-resolved DLS, demonstrating minimal interactions with serum proteins and potential as in vivo drug delivery vehicles. This thorough study of the synthesis, assembly, and characterization of zwitterionic polymers in PCMs advances the design space for charge-driven micelle assemblies.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2025

The Work of Mechanical Degradation in Elongating Polymer Melts

Molecular dynamics simulations are used to study the mechanical degradation of well-entangled polymer melts during uniaxial extensional flow. Simulations measure the transient rise in extensional stresses and relate them to the molecular alignment and scission of chain backbones. Intermolecular entanglements couple chain scission in space and time, making degradation sensitive to deformation history and strain rate in ways not displayed by dilute polymer solutions. The rate of chain scission is nonmonotonic and peaks at strains corresponding to the maximum extensibility of entanglement segments but prior to the full extension of chain backbones. We measure a specific work per scission event w* and decompose it into separate contributions associated with chain alignment, chemical bond breaking, and scission-induced plasticity. We find chain scission in melts requires activating plastic dissipation that is multiple orders of magnitude larger than the chemical work required to break a covalent backbone bond. Our findings underscore the critical need to consider bulk polymer mechanics and rheology in designing efficient mechanical degradation and mechanochemical processes.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Nondestructive Photo-Cross-Linking of Microphase-Separated Diblock Polymers through Coumarin Dimerization

The effect of long-wavelength ultraviolet photocrosslinking on microphase-separated coumarin-containing block polymers was studied by photo-rheometry and small-angle X-ray scattering. This model system consisted of three photocrosslinkable diblock polymers of poly(methoxyethyl acrylate)-b-poly(hexyl methacrylate-co-coumarin methacrylate) with different volume fractions of the crosslinkable coumarin-containing block, which microphase separated into lamellar and cylindrical morphologies. All polymers stiffened upon exposure to 365 nm light, with much greater relative increases in moduli recorded for lamellae-forming polymers (ca. 3200% increase) compared to the cylinder-forming polymer (ca. 550% increase). Disordering transitions that were evident in uncrosslinked samples were no longer observed after crosslinking in the ordered state, and domain sizes were found to remain stable to heating. The photocrosslinking reaction only proceeded under active irradiation, indicating a high degree of spatiotemporal control over curing in this system. Finally, at constant concentration of couamarin within the crosslinkable block, the cure rate was largely independent of polymer composition, suggesting a constant local concentration of coumarin moieties within the segregated crosslinkable domains. Lastly, these findings establish a set of specific structure-property relationships governing the phase-selective photocrosslinking of diblock polymers that can guide the design of robust nanostructured materials.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2020

A Fireproof, Lightweight, Polymer–Polymer Solid-State Electrolyte for Safe Lithium Batteries

Safety issues in lithium-ion batteries have raised serious concerns due to their ubiquitous utilization and close contact with the human body. Replacing flammable liquid electrolytes, solid-state electrolytes (SSEs) is thought to address this issue as well as provide unmatched energy densities in Li-based batteries. However, among the most intensively studied SSEs, polymeric solid electrolyte and polymer/ceramic composites are usually flammable, leaving the safety issue unattended. Here, we report the first design of a fireproof, ultralightweight polymer–polymer SSE. The SSE is composed of a porous mechanic enforcer (polyimide, PI), a fire-retardant additive (decabromodiphenyl ethane, DBDPE), and a ionic conductive polymer electrolyte (poly(ethylene oxide)/lithium bis(trifluoromethanesulfonyl)imide). The whole SSE is made from organic materials, with a thin, tunable thickness (10–25 μm), which endorse the energy density comparable to conventional separator/liquid electrolytes. The PI/DBDPE film is thermally stable, nonflammable, and mechanically strong, preventing Li–Li symmetrical cells from short-circuiting after more than 300 h of cycling. LiFePO 4 /Li half cells with our SSE show a high rate performance (131 mAh g –1 at 1 C) as well as cycling performance (300 cycles at C/2 rate) at 60 °C. Most intriguingly, pouch cells made with our polymer–polymer SSE still functioned well even under flame abuse tests.

25 ENERGY STORAGE↗
DOE OSTI2020

Evaluating the impact of functional groups on membrane‐mediated CO 2 / N 2 gas separations using a common polymer backbone

Abstract Polymeric membranes have shown tremendous promise for the separation of CO 2 from flue gas streams. However, few systematic studies have been conducted to better understand the impact that chemical functionalities have on membrane‐based gas separation performance. To address this gap, we herein describe the synthesis and gas separation performance of a series of vinyl‐addition polynorbornenes bearing various CO 2 ‐philic functional groups. To facilitate direct comparison between functional groups, each material was designed to maintain a common polymer backbone. Though the incorporation of CO 2 ‐philic moieties within a dense polymeric membrane is frequently hypothesized to enhance CO 2 solubility, and thereby increase CO 2 /N 2 selectivity, our results demonstrate that the incorporation of CO 2 ‐philic groups onto a common polymer backbone do not necessarily result in increased gas separation performance. Experimental and computational results demonstrate that the incorporation of amidoxime groups onto a polynorbornene backbone increase CO 2 /N 2 selectivity, whereas commonly employed ethereal side chains only increased permeability.

Higgins, Morgan A.↗
DOE OSTI2024

Waveguides for neurostimulation in the cochlea

Introduction Optical stimulation has been suggested for neural stimulation to improve cochlear implants. Light allows for more spatially selective activation of neuron populations than electrical current, offering more independent frequency bands along the spiral ganglion. These bands are available to encode acoustic information with anticipated better frequency resolution, improving cochlear implant user performance in noisy listening environments, tonal languages, and music perception. Methods Optical cochlear implants (oCIs) can deliver light either directly via small emitters within the cochlea or via waveguides from external optical sources. We investigated three waveguide designs made from OrmoComp ® , a polymer that cures through ultraviolet (UV) radiation. Waveguides were fabricated via injection molding and coated using dip-coating or thermal reflow, or through aspiration of OrmoComp ® into polyimide tubing that served as the cladding of the waveguide. The choice of fabrication technique directly determined the waveguides' total diameter: thermal reflow yielded ≈940 μm, dip-coating produced ≈306 μm, and aspiration resulted in ≈132 μm core diameter waveguides. Given the human cochlea's small size, we focused on analyzing the 306-μm and 132-μm waveguides, evaluating their optical performance (propagation and bending losses) and mechanical properties (bending stiffness and insertion forces). Furthermore, we evaluated some of these designs in in-vivo guinea pigs experiments. Results For the 100-μm core diameter waveguides, the propagation losses were 12.34 ± 1.26, 1.18 ± 0.88, 1.49 ± 0.58, and 3.43 ± 0.68 dB/cm at 534, 1,375, 1,460, and 1,550 nm, respectively. The respective bending losses at a 2 mm radius of curvature were 5.50 ± 1.32, 0.56 ± 0.26, 0.79 ± 0.18, and 0.64 ± 0.23 dB, and at 1 mm 8.54 ± 1.30, 2.05 ± 0.84, 2.11 ± 0.50, and 1.44 ± 0.37 dB. The bending stiffness of a 1 mm segment of the 100-μm-diameter waveguides was 18.9 ± 2.2 N/m. Insertion forces for the 100-μm-diameter waveguides into an acrylic human-size scala tympani model were < 25 mN. For the waveguides with 306 and 940 μm total diameter, the propagation losses ranged between 0.43 and 2.40 dB/cm at 534, 680, 1,375, and 1,550 nm, between 2.19 and 3.78 dB/cm at 450 and 1,460 nm. Bending losses for 360 degrees at 1,375 nm were 5.0, 2.4, and 0.46 for a bending radius of 2.5-, 3-, and 4-mm. Discussion Our study demonstrated that the polymer OrmoComp ® is suitable for fabricating waveguides to transmit near-infrared radiation. In-vivo experiments showed optically evoked auditory responses originating from optical stimulation in the guinea pigs' first cochlear turn while radiation was delivered. Incoming experiments will focus on evaluating long-term performance of these waveguides in guinea pigs and cats. This study will be designed to provide insights into the waveguides' performance and biocompatibility over extended periods, essential for their potential clinical application in future oCIs.

Kim, Matthew↗
DOE OSTI2023

ElectroCat: Platinum-Group-Metal-Free Engineered Framework Nano-Structure Catalyst (Final Technical Report)

Traditional synthesis methodologies that produce durable, highly active PGM-free electrocatalysts typically consist of a top-down approach utilizing a nitrogen-coordinating precursor, a metal precursor, and a support material. Nitrogen-coordinated transition metal complexes typically are absorbed onto a support material, which is then activated via high-temperature pyrolysis. Selection of the support and the nitrogen coordinating precursor has long been the focal point of efforts to maximize the number of accessible, catalytically active sites. In this project, GWE in collaboration with SRNL and NU will develop durable, highly active, low-cost, PGM-free electrocatalysts for polymer electrolyte membrane fuel cells designed and synthesized using a unique, bottom-up, rationally designed approach. Electrocatalysts are produced via polymerization reaction followed by a high-temperature pyrolysis step. Additionally, this project focuses on catalyst site and ORR mechanistic modeling to better understand the structure-property relationship.

08 HYDROGEN↗
DOE OSTI2025

How Topological Polymer Loops on the Nanoparticle Surface Control the Mechanical Properties of Nanocomposites

Carbon black (CB) and silica (SiO 2 ) filled elastomers are known to be the most successful polymer nanocomposites (PNCs) in industry, where “bound rubber (BR)” (i.e., polymer chains that are physically or chemically adsorbed on the nanofiller surface) plays a critical role in their reinforcement. Here, we report a molecular-scale mechanism underlying the “BR-induced reinforcement” by integrating neutron scattering experiments and molecular dynamics simulations. Simplified non-cross-linked SiO 2 -filled polybutadiene (PB) and CB-filled PB reveal the critical role of topological polymer loops in the BR for the enhanced mechanical performance. The average loop size on the SiO 2 surface modified with a silane coupling agent is much smaller than that on the CB surface and the loops on the SiO 2 surface are densely formed, preventing interdigitation with the matrix chains. On the other hand, the larger, uncrowded loops formed on the CB surface facilitate the interdigitation with the matrix polymer chains even near the filler surface. In this way, a strong connectivity is established between a matrix and a nanofiller, resulting in an adhesive filler–polymer interface. Furthermore, our findings shed light on rich and complex physics and materials design problems in PNCs, where the topological polymer structure on the nanofiller surface directly controls the macroscopic mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Depolymerizable and recyclable luminescent polymers with high light-emitting efficiencies

Luminescent polymers are of great interest in a number of photonic technologies, including electroluminescence, bioimaging, medical diagnosis, bio-stimulation and security signage. Incorporating depolymerizability and recyclability into luminescent polymers is pivotal for promoting their sustainability and minimizing their environmental impacts at the end of the product lifecycle, but existing strategies often compromise the light-emitting efficiencies. Here, in this study, we develop a strategy that utilizes cleavable moiety to create depolymerizable and recyclable thermally activated delayed fluorescence (TADF) polymers without compromising their high light-emitting efficiencies. The electroluminescent devices based on the TADF polymers achieved a high external quantum efficiency of up to 15.1 %. The TADF polymers can be depolymerized under either mild acidic or heating conditions, with precise control of the kinetics, and the obtained pure monomers can potentially be isolated and repolymerized for subsequent life applications. This work promotes the end-of-life environmental friendliness and circularity of luminescent materials, paving the way to a sustainable photonic industry. Developing depolymerizable and recyclable polymers with high light-emitting efficiencies is of vital importance for sustainable photonic technologies, but remains challenging. Here the authors design a strategy to develop such polymers based on the use of controllable cleavable moiety.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Creating Novel Gas Separation Constructs by Manipulating Free-Volume Distributions in Polymer-Grafted Nanoparticles

Polymer membranes are critical to many sustainability applications that require gas separation primarily based on differences in the sizes of the constituent molecules (“sieving”). The important figures of merit in this context are the rate at which the gas permeates through the membrane (or flux) and the resulting gas purity (as characterized by its selectivity). The overall goal is to maximize both gas permeability and selectivity. Currently, the ability to a priori design polymeric materials (either pure polymers or mixed matrix membranes where polymers are mixed with inorganic nanoparticles) with required permeability and selectivity remains an open challenge.

03 NATURAL GAS↗
DOE OSTI2024

RESIN: Responsible Innovation for Highly Recyclable Plastics - TASK 4: Risk Assessment Framework

This report covers the entirety of Task 4, but its main purpose is to deliver milestones ML4.4 and ML4.5, the last two SOPO milestones under Task 4. ML4.4 reports on the compatibility of polymer properties that affect both environmental performance and functional performance and the tradeoffs involved in turning these properties to the benefit of each. ML4.5 presents a complete set of information on the critical properties of benign target products, where benign products are defined as those with the shortest environmental lifetime which meet performance requirements. To support and provide context to the discussions of ML4.4 and ML4.5 and to provide a complete picture of Task 4, milestones 4.1-4.3 are briefly summarized at the beginning of the report. The discussion of ML4.4 introduces the notion of polymer persistence as a proxy for environmental risk. It then discusses the development and comparison of two machine leaning models explored for estimating polymer degradation rates, a random forest (RF) classifier and an RF regressor. Given the advantage of continuous outputs rather than simple classes, the RF regressor was incorporated in the Excel risk calculator, which to this point could implement the objectives of subtasks 4.1-4.3, estimating polymer release and redistribution. The ML4.4 discussion then addresses the effect of each of the three polymer features used by the RF regressor on polymer functional performance. These features are number molecular weight (Mn), glass transition temperature (T g ) and heat of fusion (H fus ). The discussion of ML4.5 reviews the conceptual framework of the risk model, which served as the foundation for developing the Excel risk calculator and describes the use of, and assumptions within, the calculator. Appendix A is further provided as a user’s guide for the calculator. To demonstrate how the calculator is intended to be used by developers in the design of low-risk polymers, an analysis of 27 hypothetical polymers defined by varying values for the three polymer features used by the RF regressor is presented. The range of parameter values selected produces estimates of polymer degradation rates and lifetimes that may be typical of various consumer products made from polyurethane polymers and shows how changes in polymer features affect lifetimes. The demonstration also predicts the final distribution of released polymer materials in environmental compartments as a function of consumer product mix and assumed leakage rates of end-of-life processes. Lastly, this report summarizes the achievement of Task 4 goals from original conception to final delivery and discusses how and to what degree to which each subtask goal was achieved.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Polycaprolactone: A Promising Addition to the Sequential Infiltration Synthesis Polymer Family Identified through In Situ Infrared Spectroscopy

Infiltration of inorganic oxides inside polymers using sequential infiltration synthesis (SIS) is an effective method for creating materials for a broad range of applications. The reactions between various polymer functional groups and organometallic/inorganic precursors are unique, which makes it essential to understand the specific interactions for a range of precursors and polymers to enable predictive process design and to extend the utility of SIS to applications. In this paper, in situ Fourier transform infrared spectroscopy (FTIR) measurements have been performed during Al 2 O 3 and TiO 2 SIS in three different homopolymers: poly(methyl methacrylate) (PMMA), poly(epsilon-caprolactone) (PCL), and poly(2-vinylpyridine) (P2VP). From the FTIR intensity changes after precursor exposure and during the subsequent purge times, it is demonstrated quantitatively that the interaction dynamics and the stability of the intermediate complexes of these polymers with the metal precursors are substantially different. A key finding from this comparative study is that PCL interacts far more strongly with metal precursors, even though its carbonyl (C=O) and ester (C-O-R) functional groups are similar to those of the more weakly interacting PMMA. This behavior suggests that additional factors beyond the identity of the functional groups dictate how polymers interact with metal compounds in SIS. PCL, which has not previously been reported in SIS processes, may be an attractive polymeric template for implementing SIS with improved uniformity and cost-effectiveness.

36 MATERIALS SCIENCE↗