Results for “pressure plate” — Page 17

NASA NTRS1985

Noise Transmission Loss of a Rectangular Plate in an Infinite Baffle

An improved analytical procedure was developed that allows for the efficient calculation of the noise transmission characteristics of a finite rectangular plate. Both isotropic and symmetrically laminated composite plates are considered. The plate is modeled with classic thin-plate theory and is assumed to be simply supported on all four sides. The incident acoustic pressure is assumed to be a plane wave impinging on the plate at an arbitrary angle. The reradiated pressure is assumed to be negligible compared with the blocked pressure, and the plate vibrations are calculated by a normal-mode approach. A Green's function integral equation is used to link the plate vibrations to be transmitted far-field sound waves, and transmission loss is calculated from the ratio of incident to transmitted acoustic powers. The result is a versatile research and engineering analysis tool that predicts noise transmission loss and enables the determination of the modal behavior of the plate.

Roussos, Louis A.↗

NASA NTRS1998

Prediction of Transitional Flows in the Low Pressure Turbine

Current turbulence models tend to give too early and too short a length of flow transition to turbulence, and hence fail to predict flow separation induced by the adverse pressure gradients and streamline flow curvatures. Our discussion will focus on the development and validation of transition models. The baseline data for model comparisons are the T3 series, which include a range of free-stream turbulence intensity and cover zero-pressure gradient to aft-loaded turbine pressure gradient flows. The method will be based on the conditioned N-S equations and a transport equation for the intermittency factor. First, several of the most popular 2-equation models in predicting flow transition are examined: k-e [Launder-Sharina], k-w [Wilcox], Lien-Leschiziner and SST [Menter] models. All models fail to predict the onset and the length of transition, even for the simplest flat plate with zero-pressure gradient(T3A). Although the predicted onset position of transition can be varied by providing different inlet turbulent energy dissipation rates, the appropriate inlet conditions for turbulence quantities should be adjusted to match the decay of the free-stream turbulence. Arguably, one may adjust the low-Reynolds-number part of the model to predict transition. This approach has so far not been very successful. However, we have found that the low-Reynolds-number model of Launder and Sharma [1974], which is an improved version of Jones and Launder [1972] gave the best overall performance. The Launder and Sharma model was designed to capture flow re-laminarization (a reverse of flow transition), but tends to give rise to a too early and too fast transition in comparison with the physical transition. The three test cases were for flows with zero pressure gradient but with different free-stream turbulent intensities. The same can be said about the model when considering flows subject to pressure gradient(T3C1). To capture the effects of transition using existing turbulence models, one approach is to make use of the concept of the intermittency to predict the flow transition. It was originally based on the intermittency distribution of Narasimha [1957], and then gradually evolved into a transport equation for the intermittency factor. Gostelow and associates [1994,1995] have made some improvements to Narasimha's method in an attempt to account for both favorable and adverse pressure gradients. Their approach is based on a linear, explicit combination of laminar and turbulent solutions. This approach fails to predict the overshoot of the skin friction on a flat plate near the end of transition zone, even though the length of transition is well predicted. The major flaw of Gostelow's approach is that it assumes the non-turbulent part being the laminar solution and the turbulent part being the turbulent solution and they do not interact across the transitional region. The technique in condition averaging the flow equations in intermittent flows was first introduced by Libby [1975] and Dopazo [1977] and further refined by Dick and associates [1988, 1996]. This approach employs two sets of transport equations for the non-turbulent part and the other for the turbulent part. The advantage of this approach is that it allows the interaction of non-turbulent and turbulent velocities through the introduction of additional source terms in the continuity and momentum equations for the non-turbulent and turbulent velocities. However, the strong coupling of the two sets of equations has caused some numerical difficulties, which requires special attention. The prediction of the skin friction can be improved by this approach via the implicit coupling of non-turbulent and turbulent velocity flelds. Another improvement of the interrmittency model can be further made by allowing the intermittency to vary in the cross-stream direction. This is one step prior to testing any proposal for the transport equation for the intermittency factor. Instead of solving the transport equation for the intermittency factor, the distribution for the intermittency factor is prescribed by Klebanoff's empirical formula [1955]. The skin friction is very well predicted by this new modification, including the overshoot of the profile near the end of the transition zone. The outcome of this study is very encouraging since it indicates that the proper description of the intermittency distribution is the key to the success of the model prediction. This study will be used to guide us on the modelling of the intermittency transport equation.

Huang, George↗

NASA NTRS1983

High-pressure flame visualization of autoignition and flashback phenomena with liquid-fuel spray

A study was undertaken to determine the effect of boundary layers on autoignition and flashback for premixed Jet-A fuel in a unique high-pressure windowed test facility. A plate was placed in the center of the fuel-air stream to establish a boundary layer. Four experimental configurations were tested: a 24.5-cm-long plate with either a pointed leading edge, a rounded edge or an edge with a 0.317-cm step, or the duct without the plate. Experiments at an equivalence ratio ranging from 0.4 to 0.9 were performed at pressures to 2500 kPa (25 atm.) at temperatures of 600, 645, and 700 K and velocities to 115 meters per second. Flame shapes were observed during flashback and autoignition using high speed cinematography. Flashback and autoignition limits were determined.

Marek, C. J.↗

DOE OSTI2020

Casimir force, causality, and the Gurzhi model

An extended Drude model, termed the Gurzhi model, which takes into account the electron-phonon and electron-electron interactions, is applied to calculate the Casimir force between two metallic plates. It is shown that although the dielectric permittivity of the Gurzhi model has a first-order pole in the upper half-plane of complex frequencies and, thus, violates the causality principle, it can be used in a restricted frequency interval in combination with the experimental permittivity determined by the optical data for the complex index of refraction. The imaginary part of the Gurzhi dielectric permittivity of Au at low frequencies demonstrates better agreement with the permittivity given by the optical data than the simple Drude model. The Casimir pressure between two Au plates is computed using the Gurzhi, Drude, and plasma model approaches, taking into account the optical data, as well as with the simple Drude and plasma models. Finally, the contribution of the electron-electron scattering to the Casimir pressure is estimated. Although a comparison with the measurement data of two precise experiments shows that the Gurzhi model does not resolve the Casimir puzzle, the obtained results suggest further clarification of this fundamental problem.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

NASA NTRS1974

Scanning nozzle plating system

A plating system is described in which a substrate to be plated is supported on a stationary platform. A nozzle assembly with a small nozzle is supplied with a plating solution under high pressure, so that a constant-flow stream of solution is directed to the substrate. The nozzle assembly is moved relative to the substrate at a selected rate and movement pattern. A potential difference (voltage) is provided between the substrate and the solution in the assembly. The voltage amplitude is modulated so that only when the amplitude is above a minimum known value plating takes place.

Oliver, G. D.↗

NASA NTRS1995

An experimental study of a turbulent boundary layer in the trailing edge region of a circulation-control airfoil

This report describes the development of a new near-wall LDV technique and its use to measure the full turbulent stress tensor in a highly three-dimensional separated boundary layer flow. Laser Doppler velocimetry, with small diameter laser beams allowing small beam-crossing angles (i.e., larger fringe spacings), was used, resulting in measurements close to solid surfaces. Dennis Johnson of NASA/Ames combined the advantages offered by FFT signal processors with a beam-steering probe inserted in the flow to devise a new self-aligning, near-wall LDV approach capable of making direct measurements of the transverse velocity component. This new technique was applied to a 2D, zero-pressure-gradient, flat-plate boundary layer in the High Reynolds Number Pilot Channel at Ames. Accurate and repeatable measurements of U and uu to within 30 mm of the wall were obtained. Next, the near-wall LDV technique was employed in a 3D separated boundary layer flow, consisting of a 2-dimensional wall boundary layer approaching a right-angle wedge. The resulting lateral and adverse streamwise pressure gradients generated significant spanwise velocities and turbulent stresses, and a large reverse-flow region. The near-wall LDV was modified further to facilitate measurements in the 3D Wedge Flow.

Brown, Jeffrey↗

NASA NTRS1977

Effects of jet decay rate on jet induced loads on a flat plate

Experimental modelling of the interaction between a jet and an aircraft wing or fuselage in VTOL aircraft was undertaken using a cold jet exiting perpendicular to a flat plate in a uniform cross-flow. Effects of jet decay rate and jet-to-cross-flow velocity ratio, R, on the induced load distribution were investigated. Jet decay rate was increased by using cylindrical centerbodies submerged in the jet nozzle, which caused nonuniform initial jet velocity profiles. Quicker jet decay rate, corresponding to the presence of a centerbody, resulted in as much as 50% reduction in the induced pressure loads on the plate. This has implications in interpretation of results from earlier VTOL model studies of jet induced loads, where the jets have often had relatively slow decay rates due to uniform initial velocity profiles

Kuhlman, J. M.↗

NASA NTRS1973

Experimental study of supersonic laminar base flow with and without suction

Heat-transfer and pressure distributions in laminar separated flows downstream of rearward-facing steps with and without mass suction were investigated at Mach numbers around 4 for the conditions when the boundary-layer thickness was comparable to or larger than the step height. In both suction and no-suction cases, an increase of the step height resulted in a sharp drop of the base heating rates, which then gradually recovered to less than or near attached-flow values obtained with flat-plate configuration. Mass suction from the step base area increased the local heating rates; this effect, however, was relatively weak for laminar flows tested, and the competing effect of the step height clearly predominated. It was found that even removal of the entire incoming boundary layer was not sufficient to raise the poststep heating rates above the flat-plate values. The base pressure in the no-suction, solid-step case correlated reasonably well with the step height-to-boundary-layer thickness ratio and with the Reynolds number based on the step height.

Jakubowski, A. K.↗

DOE OSTI2025

Fabrication of the HFVMTF Double-Bath Cryostat

The High Field Vertical Magnet Test Facility (HFVMTF) at Fermilab is designed to test superconducting magnets up to 20 tons and 1.3 meters in diameter. Central to the facility is a double-bath superfluid helium cryostat reaching 1.8 K at 1.2 bar. Integrated with a 15 T superconducting dipole from LBNL, HFVMTF supports HTS cable testing for fusion applications. This paper presents the design and fabrication of the cryostat, with a focus on two complex components: the 2 K heat exchanger and the lambda plate. The heat exchanger thermally links sub-atmospheric and pressurized helium baths. The 1.4-meter lambda plate provides thermal isolation and structural support for over 20 tons under 1.3 bar pressure differential. Finite Element Analysis validated the vessel’s integrity under maximum load conditions.

Bruce, Romain [Fermilab] (ORCID:0000000234200612)↗

DOE OSTI2025

Fabrication of the HFVMTF Double-Bath Cryostat

The High Field Vertical Magnet Test Facility (HFVMTF) at Fermilab is designed to test superconducting magnets up to 20 tons and 1.3 meters in diameter. Central to the facility is a double-bath superfluid helium cryostat reaching 1.8 K at 1.2 bar. Integrated with a 15 T superconducting dipole from LBNL, HFVMTF supports HTS cable testing for fusion applications. This paper presents the design and fabrication of the cryostat, with a focus on two complex components: the 2 K heat exchanger and the lambda plate. The heat exchanger thermally links sub-atmospheric and pressurized helium baths. The 1.4-meter lambda plate provides thermal isolation and structural support for over 20 tons under 1.3 bar pressure differential. Finite Element Analysis validated the vessel's integrity under maximum load conditions.

Bruce, R. [Fermilab] (ORCID:0000000234200612)↗

DOE OSTI2020

Mechano-Electrochemical Interaction in Solid-State Lithium Batteries

A solid-state lithium (Li) battery primarily consists of Li metal anode, solid electrolyte separator, and cathode. The asymmetric volume changes, originating from ion transport and interfacial Li growth during plating, lead to significant stresses in the layered architecture. In this study, we develop a coupled mechanics-electrochemistry formalism for polymer electrolyte based solid-state batteries, in particular, focusing on the stress effect on electrochemical performance. By means of a coupling coefficient, it is found that stress-assisted ion transport in the electrolyte results in a delayed Sand’s time and increased critical current density of unstable electrodeposition, and consequently, alleviates the propensity of dendrite formation. Stress at the Li metal-electrolyte interface affects the electrochemical reaction kinetics, and the influences from the deviatoric stress and hydrostatic pressure vary with Li plating time. In addition, a low restraint stiffness to the layered structure could elastically buffer the volumetric changes and thus reduce the stress during Li plating. This fundamental study provides guidance for the design of solid-state batteries, aimed at stable electrodeposition and mechanical integrity.

25 ENERGY STORAGE↗

NASA NTRS2001

Neural-Net Processed Characteristic Patterns for Measurement of Structural Integrity of Pressure Cycled Components

A neural-net inspection process has been combined with a bootstrap training procedure and electronic holography to detect changes or damage in a pressure-cycled International Space Station cold plate to be used for cooling instrumentation. The cold plate was excited to vibrate in a normal mode at low amplitude, and the neural net was trained by example to flag small changes in the mode shape. The NDE (nondestructive-evaluation) technique is straightforward but in its infancy; its applications are ad-hoc and uncalibrated. Nevertheless previous research has shown that the neural net can detect displacement changes to better than 1/100 the maximum displacement amplitude. Development efforts that support the NDE technique are mentioned briefly, followed by descriptions of electronic holography and neural-net processing. The bootstrap training procedure and its application to detection of damage in a pressure-cycled cold plate are discussed. Suggestions for calibrating and quantifying the NDE procedure are presented.

Decker, A. J.↗

NASA NTRS2006

Pressure Gradient Effects on Hypersonic Cavity Flow Heating

The effect of a pressure gradient on the local heating disturbance of rectangular cavities tested at hypersonic freestream conditions has been globally assessed using the two-color phosphor thermography method. These experiments were conducted in the Langley 31-Inch Mach 10 Tunnel and were initiated in support of the Space Shuttle Return-To-Flight Program. Two blunted-nose test surface geometries were developed, including an expansion plate test surface with nearly constant negative pressure gradient and a flat plate surface with nearly zero pressure gradient. The test surface designs and flow characterizations were performed using two-dimensional laminar computational methods, while the experimental boundary layer state conditions were inferred using the measured heating distributions. Three-dimensional computational predictions of the entire model geometry were used as a check on the design process. Both open-flow and closed-flow cavities were tested on each test surface. The cavity design parameters and the test condition matrix were established using the computational predictions. Preliminary conclusions based on an analysis of only the cavity centerline data indicate that the presence of the pressure gradient did not alter the open cavity heating for laminar-entry/laminar-exit flows, but did raise the average floor heating for closed cavities. The results of these risk-reduction studies will be used to formulate a heating assessment of potential damage scenarios occurring during future Space Shuttle flights.

Everhart, Joel L.↗

NASA NTRS2007

Pressure Gradient Effects on Hypersonic Cavity Flow Heating

The effect of a pressure gradient on the local heating disturbance of rectangular cavities tested at hypersonic freestream conditions has been globally assessed using the two-color phosphor thermography method. These experiments were conducted in the Langley 31-Inch Mach 10 Tunnel and were initiated in support of the Space Shuttle Return-To-Flight Program. Two blunted-nose test surface geometries were developed, including an expansion plate test surface with nearly constant negative pressure gradient and a flat plate surface with nearly zero pressure gradient. The test surface designs and flow characterizations were performed using two-dimensional laminar computational methods, while the experimental boundary layer state conditions were inferred using the measured heating distributions. Three-dimensional computational predictions of the entire model geometry were used as a check on the design process. Both open-flow and closed-flow cavities were tested on each test surface. The cavity design parameters and the test condition matrix were established using the computational predictions. Preliminary conclusions based on an analysis of only the cavity centerline data indicate that the presence of the pressure gradient did not alter the open cavity heating for laminar-entry/laminar-exit flows, but did raise the average floor heating for closed cavities. The results of these risk-reduction studies will be used to formulate a heating assessment of potential damage scenarios occurring during future Space Shuttle flights.

Everhart, Joel L.↗

NASA NTRS1984

Computer programs to predict induced effects of jets exhausting into a crossflow

A user's manual for two computer programs was developed to predict the induced effects of jets exhausting into a crossflow. Program JETPLT predicts pressures induced on an infinite flat plate by a jet exhausting at angles to the plate and Program JETBOD, in conjunction with a panel code, predicts pressures induced on a body of revolution by a jet exhausting normal to the surface. Both codes use a potential model of the jet and adjacent surface with empirical corrections for the viscous or nonpotential effects. This program manual contains a description of the use of both programs, instructions for preparation of input, descriptions of the output, limitations of the codes, and sample cases. In addition, procedures to extend both codes to include additional empirical correlations are described.

Perkins, S. C., Jr.↗

NASA NTRSDate not supplied

Ice Growth Model for Polar Water Capture Systems

In-situ resource utilization (ISRU) is essential to NASA’s goal of sustainable and cost-effective missions to the Moon and beyond. Water has become a particular source of interest since its discovery in the permanently shadowed regions (PSRs) of the Moon. This water exists as ice bound within the regolith, so one mode of capture is heating to sublimation temperatures and capturing at very low pressure. It then can be stored in ice form and transported out of the PSR and to a sunlit ridge, where processes such as electrolysis can be performed[2]. An understanding of frost growth dynamics under rarefied conditions is necessary for successful water capture and storage due to transient thermal properties of frost. A Diffusion-Limited Aggregation (DLA) approach was taken to analytically model bulk thermal conductivity changes of the growing frost layer under varying wall temperatures and frost layer porosities. The model utilizes well-known correlations for effective thermal conductivity and records the values as the frost layer thickness increases. This thermal conductivity can be applied to a known temperature change and be used to evaluate heat flux through the combined frost layer and tank wall for either a flat plate or cylindrical geometry. An experiment is described that will evaluate this model using one-dimensional frost growth on a horizontal, flat plate under low-pressure. The ice growth will be measured using a millimeter-scale photogrammetry camera system and a load cell measured transient mass growth.

In situ Resource Utilization↗

NASA NTRSDate not supplied

Ice Growth Model for Polar Water Capture Systems

In-situ resource utilization (ISRU) is essential to NASA’s goal of sustainable and cost-effective missions to the Moon and beyond. Water has become a particular source of interest since its discovery in the permanently shadowed regions (PSRs) of the Moon. This water exists as ice bound within the regolith, so one mode of capture is heating to sublimation temperatures and capturing at very low pressure. It then can be stored in ice form and transported out of the PSR and to a sunlit ridge, where processes such as electrolysis can be performed[2]. An understanding of frost growth dynamics under rarefied conditions is necessary for successful water capture and storage due to transient thermal properties of frost. A Diffusion-Limited Aggregation (DLA) approach was taken to analytically model bulk thermal conductivity changes of the growing frost layer under varying wall temperatures and frost layer porosities. The model utilizes well-known correlations for effective thermal conductivity and records the values as the frost layer thickness increases. This thermal conductivity can be applied to a known temperature change and be used to evaluate heat flux through the combined frost layer and tank wall for either a flat plate or cylindrical geometry. An experiment is described that will evaluate this model using one-dimensional frost growth on a horizontal, flat plate under low-pressure. The ice growth will be measured using a millimeter-scale photogrammetry camera system and a load cell measured transient mass growth.

ice growth↗

NASA NTRS1991

Small-scale experiments in STOVL ground effects

A series of tests was completed in which suckdown and fountain forces and pressures were measured on circular plates and twin-tandem-jet generic STOVL (short takeoff and vertical landing) configurations. The tests were conducted using a small-scale hover rig, for jet pressure ratios up to 6 and jet temperatures up to 700 F. The measured suckdown force on a circular plate with a central jet was greater than that found with a commonly used empirical prediction method. The present data showed better agreement with other sets of data. The tests of the generic STOVL configurations were conducted to provide force and pressure data with a parametric variation of parameters so that an empirical prediction method could be developed. The effects of jet pressure ratio and temperature were found to be small. Lift improvement devices were shown to substantially reduce the net suckdown forces.

Corsiglia, Victor R.↗