Search NASA⌕ Search

SEARCH · Search NASA

Results for “processability assessment”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Affinity of LDR Organics to Cementitious Materials: Sorption and Leaching Tests

SRNL is working to identify and test the physiochemical interactions of organic contaminants of potential concern with minerals in grout/cementitious materials. Organic species may interact with cementitious minerals including slag, fly ash, cement, and other components/dopants like carbon in fly ash. The identification of such interactions will support the solidification process design, performance assessments for the chemicals of concern, and a proposed Resource Conservation and Recovery Act (RCRA) treatment variance specified for the Land Disposal Restriction (LDR) organics associated with Hanford tank waste. Inably expected to be present LDR organics associated with Hanford tank waste (RPP-RPT-63493, Rev 1a) was screened by functional groups, octanol-water partitioning coefficients, and detection frequency in Hanford tank waste samples. A subset of 10 compounds, spanning the identified properties, were tested using sorption and leachate tests. These compounds were subjected to traditional batch sorption tests and leaching tests on/from Cast Stone cementitious material with and without activated carbon (a potential organic adsorption additive). The interactions between organic compounds were observed in traditional batch sorption and modified Toxic Characteristic Leaching Procedure (TCLP) leachate tests for a surrogate Cast Stone material with and without an activated carbon addition. Specifically, phthalic acids (negatively charged) and 4-chloroaniline (polar) sorbed strongly to unmodified Cast Stone and a group of 3 phenolic compounds (2,4,6-Trichlorophenol, Pentachlorophenol, o-Cresol) were sorbed to and were retained by Cast Stone with a 1% activated carbon amendment.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Probing Dark Sectors with Neutron Stars

Tensions in the measurements of neutron and kaon weak decays, such as of the neutron lifetime, may speak to the existence of new particles and dynamics not present in the Standard Model (SM). In scenarios with dark sectors, particles that couple feebly to those of the SM appear. We offer a focused overview of such possibilities and describe how the observations of neutron stars, which probe either their structure or dynamics, limit them. In realizing these constraints, we highlight how the assessment of particle processes within dense baryonic matter impacts the emerging picture—and we emphasize both the flavor structure of the constraints and their broader connections to cogenesis models of dark matter and baryogenesis.

baryon number↗
DOE OSTI2021

Optimization Of In-field Alpha Spectrometry For Uranium Enrichment Determination In Uranium Hexafluoride

In response to needs identified by the International Atomic Energy Agency (IAEA) research is underway to develop In-Field Alpha Spectrometry (IFAS) as a method to allow IAEA safeguards inspectors to collect samples of uranium hexafluoride (UF6) at processing facilities to assess and verify uranium enrichment. For sample collection, the IFAS method uses Single-Use Destructive Assay (SUDA) samplers, which contain thin zeolite coatings that trap UF6 gas and convert it to the safer, more stable form uranyl fluoride (as a dihydrate, UO2F2·2H2O). For alpha spectrometry, the IFAS instrument employs a large area silicon semiconductor transducer to detect and record alpha particle energy-deposition events. Over the past year optimization work has significantly increased the diameter of useful SUDA samples (from 12.7 mm to 48 mm), improved the manufacturability and reproducibility of SUDA samples, increased the area of the IFAS alpha spectrometer sensor from 1.2 cm to 3.1 cm, and improved source positioning within the IFAS. This paper will report on this optimization work, its impacts on IFAS performance, and future plans for IFAS miniaturization, improvements, and testing.

Chichester, David↗
DOE OSTI2022

Ushering in the New Age of Laboratories: Smart Labs in Practice; Preprint

Ventilation is the first line of defense against airborne hazards produced during research activities in laboratories. A vital component to maintaining healthy, safe, indoor air quality, laboratory ventilation systems are often victim to ineffective operation, posing a risk to an organization's most important asset - the researchers. Furthermore, system inefficiencies can lead to up to 50% wasted energy. By providing a framework to improve the safety and energy efficiency through optimized ventilation and operations, the Smart Labs Toolkit guides laboratory stakeholders through a straight-forward, holistic approach to achieving a dynamic Smart Labs program. A Smart Labs program employs a combination of physical, administrative, and management techniques to plan, assess, optimize, and manage high-performance laboratories. Grounded in the Smart Labs methodology, the National Renewable Energy Laboratory (NREL) implemented a successful Smart Labs program to oversee the design, construction, maintenance, and operations of its laboratories. To accomplish this effort, NREL's key stakeholders created an internal partnership to align NREL's existing laboratories with Smart Labs principles and solidify organizational roles for the safe and efficient operation of laboratory assets. The program provides the groundwork for decarbonization strategies centered around building operation. This paper outlines best practices employed by NREL to develop a cross-cutting Smart Labs team, garner managerial support, and effectively communicate of goals around safety and energy. Strategies include specific Smart Labs best practices, such as implementing a Laboratory Ventilation Risk Assessment - a systematic process for identifying risk due to airborne hazards and informing dynamic, demand-based ventilation to optimize safety and efficiency.

decarbonization↗
DOE OSTI2021

Optimization of In-Field Alpha Spectrometry for Uranium Enrichment Determination in Uranium Hexafluoride

In response to needs identified by the International Atomic Energy Agency (IAEA) research is underway to develop In-Field Alpha Spectrometry (IFAS) as a method to allow IAEA safeguards inspectors to collect samples of uranium hexafluoride (UF6) at processing facilities to assess and verify uranium enrichment. For sample collection, the IFAS method uses Single-Use Destructive Assay (SUDA) samplers, which contain thin zeolite coatings that trap UF6 gas and convert it to the safer, more stable form uranyl fluoride (UO2F2). For alpha spectrometry, the IFAS instrument employs a large area silicon semiconductor transducer to detect and record alpha particle energy-deposition events. Over the past year optimization work has significantly increased the diameter of useful SUDA samples (from 12.7 mm to 48 mm), improved the manufacturability and reproducibility of SUDA samples, increased the area of the IFAS alpha spectrometer sensor from 1.2 cm to 3.1 cm, and improved source positioning within the IFAS. This paper will report on this optimization work, its impacts on IFAS performance, and future plans for IFAS miniaturization, improvements, and testing.

46 - INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AN↗
DOE OSTI2022

Sensing and control of additive manufacturing processes

Systems, devices, and methods for additive manufacturing are provided that allow for components being manufactured to be assessed during the printing process. As a result, changes to a print plan can be considered, made, and implemented during the printing process. More particularly, in exemplary embodiments, a spectrometer is operated while a component is being printed to measure one or more parameters associated with one or more layers of the component being printed. The measured parameter(s) are then relied upon to determine if any changes are needed to the way printing is occurring, and if such changes are desirable, the system is able to implement such changes during the printing process. By way of non-limiting examples, printed material in one or more layers may be reheated to alter the printed component, such as to remove defects identified by the spectrometer data. A variety of systems, devices, and methods for performing real-time sensing and control of an additive manufacturing process are also provided.

Penny, Ryan Wade↗
DOE OSTI2021

Comprehensive Margin Assessment of the ASME Section III, Division 5, Class A Primary Load Design Rules

This report provides a comprehensive margin assessment of the ASME Section III, Division 5, Subsection HB, Subpart B rules for the design of high temperature reactor components against load controlled stress limits. These rules, often called the Code primary load design rules, provide protection against creep rupture and plastic collapse under steady conditions. The method adopted here is to compare the deterministic ASME design life, according to the primary load design rules, against the expected, statistical service life of the component, considering creep rupture as the relevant failure mode. The report provides the design margin of the ASME rules in terms of the probability of premature failure -- the probability that the component fails in service before reaching the ASME design life. To complete this assessment, the report describes the development of a statistical creep life assessment procedure accounting for variations in the component loading, material creep rate, and the material rupture time. This includes a novel method for correlating creep rupture data using a Gaussian process accounting for heat-to-heat variation in the Larson-Miller time-temperature parameter. The report applies the complete margin assessment process to quantify the design margin inherent in the ASME primary load design rules as a function of temperature for relevant component geometries and materials. The overall conclusion is that the ASME rules are conservative, providing designs with very small probability of premature failure, but some optimization of the Code design rules is possible to provide a more uniform design margin.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

DER Cybersecurity R&D

The National Renewable Energy Laboratory (NREL) conducted more than 30 assessments for utilities across the United States with a cybersecurity assessment tool based on the U.S. Department of Energy (DOE) Cybersecurity Capability Maturity Model (C2M2) and the National Institute of Standards and Technology (NIST) Cybersecurity Framework (CSF) and focused on business process. With funding from the DOE Office of Renewable Energy and Energy Efficiency Federal Energy Management Program, NREL modified the current cyber governance assessment tool to include an assessment process specifically for distributed energy resources (DERs). The Distributed Energy Resources Cybersecurity Framework (DER-CF) was developed to help federal agencies mitigate gaps in their cybersecurity posture for distributed energy systems.

cybersecurity valuation↗
DOE OSTI2020

Biological Valorization of Natural Gas for the Production of Lactic Acid: Techno-Economic Analysis and Life Cycle Assessment

Due to the availability of natural gas, shale gas, and flared gas, there is increased interest in converting methane in these gases into commodity chemicals via cost-effective and sustainable processes. Recently, we have demonstrated an efficient process concept converting methane to lactic acid (LA) by methanotrophic bacteria with high carbon flux, pivoting potentials for commercialization. Herein, we present a first-of-kind conceptual design and a techno-economic analysis (TEA) of a biorefinery process with calculated minimum selling prices. This study includes both sensitivity analysis and scenario analysis for key cost drivers and for projecting path forwards in research and development. The analyses reveal that the conversion efficiency, LA product titer, LA productivity, and gas flow rate have the most significant impacts on cost. The MSP varies from $5.83-$2.17/kg LA depending on these key process attributes. Further, a life cycle assessment of this process concept is evaluated and compared to understand the sustainable aspects. In this TEA study, the bio-upgrading process from natural gas to LA presents a potentially promising approach in terms of the feedstock versatility, economic viability, and environmental impact.

BIOMASS FUELS,NATURAL GAS↗
DOE OSTI2025

A Novel Continuous Ultrasound-Assisted Leaching Process for Rare Earth Element Extraction: Environmental and Economic Assessment

Rare earth elements (REEs) make up integral components in personal electronics, healthcare instrumentation, and modern energy technologies. REE leaching with organic acids is an environmentally friendly alternative to traditional extraction methods. Our previous study demonstrated that batch ultrasound-assisted organic acid leaching of REEs can significantly decrease environmental impacts compared to traditional bioleaching. The batch method is limited to small volumes and is unsuitable for industrial implementation. This study proposes a novel approach to increase reaction volume using a continuous ultrasound-assisted organic acid leaching method. Laboratory experiments showed that continuous ultrasound-assisted leaching increased the leaching rate (µg/h) 11.3–24.5 times compared to our previously reported batch method. Techno-economic analysis estimates the cost of the continuous approach using commercially purchased organic acids is $\$$9465/kg of extracted REEs and $\$$4325/kg of extracted REEs, using gluconic acid and citric acid, respectively. The sensitivity analysis reveals that substituting commercially purchased organic acids with microbially produced biolixiviant can reduce the process cost by approximately 99% while minimally increasing energy consumption. Environmental assessment shows that most of the emissions stemmed from the energy required to power the ultrasound reactor. We concluded that increased leaching capacity using a continuous ultrasound-assisted approach is feasible, but process modifications are needed to reduce the environmental impact.

54 - ENVIRONMENTAL SCIENCES/GLOBAL CLIMATE CHANGE ↗
DOE OSTI2024

A Conceptual Design and Economic Assessment of a Chitin Biorefinery Based on Shrimp Processing Wastes

Due to the extensive production of shrimp in captivity, waste generation has increased significantly and has become an environmental problem. The recovery of biomolecules can be an important way to mitigate the environmental problems associated with processing in this sector. In this sense, the present work aimed to evaluate a biorefinery approach for valuing shrimp farming waste to obtain astaxanthin, chitin and chitosan. Stoichiometric segmentation was used as a tool to identify the process steps, whose information on process variables (fresh water consumption, flow rate and reaction conditions) was adapted from the literature. A biorefinery coupled to a shrimp processing plant was proposed for the immediate use of highly perishable biomass, to guarantee the quality of the extracted products and reduce storage and transportation costs. In practice, the biomass treatment sequence adopted (demineralization followed by deproteinization) eliminates the depigmentation step, as the chitin obtained has a lighter tone. The proposed route was evaluated for four scenarios based on two indicators: gross economic potential (EGP) and metrics for inspection of sales and reagents (MISR). The results indicate that economic viability is achieved only for the production of chitosan, resulting in a gross revenue of US$832.50/cycle and a MISR value > 1. The sale of astaxanthin promotes an increase of US$3.73/cycle in the EGP, considered too low for the inclusion of another stage in the process.

astaxanthin↗
DOE OSTI2021

Simulation-based methodology to assess the lattice defects creation as energy storing process

In nuclear industry, damages caused to in-core structural materials by high-energy neutrons have been studied for years. Recently, the possibility of storing energy through the creation of defects in crystalline materials via heavy particle bombardment was investigated. To evaluate the potential of the Wigner effect as energy-storing process, a graphite-moderated Molten Salt Reactor was adopted as a test case. Neutronics simulations performed with OpenMC Monte Carlo code allowed estimating the amount of energy released during fission events, the fraction that is deposited in graphite, and the fraction that has the potential to cause radiation damages. Additionally, molecular dynamics simulations were then performed to study the evolution of cascades triggered by high-energy neutrons. As a major outcome, a more accurate estimate of the radiation damage with respect to the traditional approaches was obtained, and the fraction of the deposited neutron energy that can be stored through long-lived defects was quantified.

25 ENERGY STORAGE↗
DOE OSTI2023

An innovative approach for atrazine electrochemical oxidation modelling: Process parameter effect, intermediate formation and kinetic constant assessment

Water reuse for irrigation activities is becoming a crucial worldwide challenge due to the depletion of water sources. Anyway, agricultural drainage can potentially contain dangerous contaminants such as metals, pesticides, and herbicides, including atrazine. To address the need for agriculture wastewater purification, we investigated atrazine removal from simulated wastewater by electro-oxidation using platinum-coated titanium electrodes on a lab-scale experimental apparatus. The effects of electrolyte composition and concentration, i.e. ionic strength and applied current density on atrazine removal, were investigated. The results demonstrated that the electrochemical oxidation of the herbicide occurred through two routes, depending on the presence or absence of oxidizing chlorine species. The generation of intermediates during the treatment was monitored and quantified by evaluating the effect of an inert electrolyte (NaClO 4 ) versus an oxidizable chlorine species (NaCl). In both experimental conditions, five intermediates were identified, including desethyl-atrazine (DEA), hydroxyatrazine (ATZ-OH), desisopropyl-atrazine (DIA) and desethyl-desisopropyl-atrazine (DEDIA). A degradation mechanism and a model for describing hydroxyl radicals and active chlorine species contributions at ATZ oxidation were also proposed. Intermediate evolution profiles suggest that ATZ degradation can be considered as a series–parallel reaction system. Finally, the energy requirement assessment for ATZ removal was carried out. The highest ATZ removal (≅98%) was achieved with NaCl = 0.08 M, J = 60 A/m −2 , and E C = 5.83 kWh m −3 . Results highlight that atrazine removal was improved when an active chlorine species (NaCl) was present in the water solution. Moreover, the addition of chlorine species during electro-oxidation is an energy-saving strategy. Collectively, electro-oxidation technique can be efficiently applied to treat polluted water in order to meet the needs of recycling water quality and reduce resource consumption.

Electro-chemical oxidation↗
DOE OSTI2021

Critical adjustment of land mitigation pathways for assessing countries' climate progress

Collective progress towards the Paris Agreement’s temperature targets will be assessed by the Agreement’s Global Stocktake process. Global emission pathways by Integrated Assessment Models (IAMs) are a likely benchmark against which aggregated countries’ greenhouse gas mitigation pledges will be assessed. However, this approach requires comparability, which is currently hampered by a 5 GtCO2yr-1 mismatch between the estimated global land anthropogenic flux of IAMs and countries’ GHG inventories (GHGIs) for 2005-2015. We show that this gap is mostly the result of differences in how the anthropogenic forest sink is defined. Countries define managed forest more broadly than IAMs, and on this larger area typically consider anthropogenic also fluxes due to human-induced environmental change, which IAMs do not include their pathways. Using five IAMs and a dynamic global vegetation model (DGVM), we present and apply a novel method that adjusts IAM results to the countries’ definition, closing the gap with GHGIs at global and regional scale. When expressed in a way compatible with GHGIs, adjusted 1.5°C and well-below 2°C pathways have a cumulative CO2 balance until carbon neutrality that is 110–176 GtCO2 lower than the original IAMs pathways. The use of these country-compatible emission pathways under the Global Stocktake would therefore be essential for an accurate assessment of the collective progress towards the Paris Agreement’s climate goals.

Grassi, Giacomo↗
DOE OSTI2024

A Simulation Modeling Approach to Optimizing Nuclear Waste Dispositioning

The dispositioning of nuclear waste generated at facilities across the country is an ongoing battle that affects us all. National laboratories and research centers dealing in medical research, clean energy, and other nuclear activities such as the Department of Energy (DOE) facilities face the need to properly manage and dispose of nuclear waste. A dynamic modeling solution would enable the DOE and others to make decisions on waste disposal and technological options. In doing so, this research explores modeling techniques using available data to address these situations. The focus being on developing an initial robust and adaptable discrete event model using the ExtendSim tool. This modeling effort will target the dispositioning of transuranic waste at the Savannah River National Laboratory (SRNL) which can be expanded to represent the current state of disposition process for waste generated at other DOE facilities. The model aims to assess resource allocation and waste processing options to stabilize productivity and cut the backlog of nuclear waste. By assessing the results of different scenarios, this research aims to provide actionable insights for the DOE. This approach has the potential to significantly improve the management of radioactive waste, offering the capability of evaluating options for optimizing the process for nuclear waste disposal. The findings of this study can serve as a valuable resource for decision-makers and other national laboratories, or research entities engaged in nuclear operations by enabling them to make more informed choices.

Andaverde, Alexis↗
DOE OSTI2025

Development of a thermal creep model for aluminum alloy 6061 cladding in U-10Mo monolithic fuel plates

Plate-type fuel elements consisting of a high-density, low-enriched uranium (LEU) U–10Mo-based fuel foil encapsulated in an aluminum alloy (AA) cladding are fabricated using the hot isostatic pressing (HIP) technique. During the HIP process, the fuel plate system is heated to 560 °C, then cooled to room temperature. This heat cycle significantly affects the mechanical properties of the aluminum cladding, and experimental investigations have shown that, post-HIP bonding, the mechanical properties of the aluminum cladding transition from those of AA 6061-T6 to something closer to the O temper. More specifically, the ultimate strength of the cladding decreases while its ductility increases, making it challenging to capture the changes in mechanical behavior and material properties. Understanding the residual stresses generated during the HIP process is critical for assessing the fuel plate’s integrity under various temperature, pressure, and irradiation. To simulate the HIP bonding process, the elastic, plastic, and thermal properties of the cladding are assumed to be similar to those of AA 6061-O temper. However, the primary challenge lies in the lack of available data for the creep model of the AA 6061 cladding during this transient process of HIP. The present study focuses on developing a computational model that predicts the creep behavior of the aluminum cladding in the fuel plates during the HIP process, as cladding creep significantly influences the residual stresses generated in U-10Mo fuel plates during HIP fabrication. Furthermore, as HIP bonding occurs at high temperatures that are nearing the melting point of aluminum, the present work considered a temperature-dependent Arrhenius-type creep model. In particular, a hyperbolic sine creep model is employed to estimate the creep properties of the as-fabricated aluminum cladding. In conclusion, the residual stresses predicted in the U-10Mo fuel when using the newly calibrated creep model closely align with the experimental measurements, validating the model’s accuracy.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Investigating Scientific Data Change with User Research Methods

Scientific datasets are continually expanding and changing due to fluctuations with instruments, quality assessment and quality control processes, and modifications to software pipelines. Datasets include minimal information about these changes or their effects requiring scientists manually assess modifications through a number of labor intensive and ad-hoc steps. The Deduce project is investigating data change to develop metrics, methods, and tools that will help scientists systematically identify and make decisions around data changes. Currently, there is a lack of understanding, and common practices, for identifying and evaluating changes in datasets since systematically measuring and managing data change is under explored in scientific work. We are conducting user research to address this need by exploring scientist's conceptualizations, behaviors, needs, and motivations when dealing with changing datasets. Our user research utilizes multiple methods to produce foundational, generative insights and evaluate research products produced by our team. In this paper, we detail our user research process and outline our findings about data change that emerge from our studies. Our work illustrates how scientific software teams can push beyond just usability testing user interfaces or tools to better probe the underlying ideas they are developing solutions to address.

96 KNOWLEDGE MANAGEMENT AND PRESERVATION↗