Search NASA⌕ Search

SEARCH · Search NASA

Results for “rate constants”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Lessons Learned in Employing Data Analytics to Predict Oxidation Kinetics and Spallation Behavior of High-Temperature NiCr-Based Alloys

Machine learning (ML) can offer many advantages in predicting material properties over traditional materials development methods based solely on limited experimental investigations or physical-based simulations with the capability to reduce development cost, risk, and time. However, so far, limited efforts have been made to predict alloy oxidation kinetics and spallation behavior via ML due to the lack of consistently measured and sufficient experimental data and the inherent complexity in oxidation behavior of multicomponent high-temperature alloys. A previous study reported the ability of ML to predict oxidation kinetics of NiCr-based alloys as a function of alloy composition and operating conditions. Here, the performance of a ML model in predicting rate constants and spallation probability was evaluated in light of the roles of the data distribution of the experimental dataset (data analytics), the alloy composition, the exposure environment and the chosen oxidation approach to extracting kinetic values from the measured mass changes (but using either a simple parabolic law or a statistical cyclic oxidation model). Potential strategies to improve the predictions and enhance the extrapolative capability of the previously trained model will be discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Oxidation Lifetime Modeling of 625 and 120 Foils After Long-term Exposure in Flowing Air + 10% ${\hbox {H}_2\hbox {O}}$ at 700 and 800 $^\circ$C

A model describing oxidation kinetics considering simultaneous oxidation and volatilization of external oxide scales was integrated with a CALPHAD-based coupled thermodynamic and kinetic approach to predict the oxidation-induced lifetime of foils of alloys 625 and 120. Long-term exposures in flowing air +10% H 2 O at 700 and 800 °C under two flow velocities were used to validate the modeling results. The time to a critical Cr concentration of 10 wt% at the oxide/alloy interface, t 10 , was shown to correlate with the breakdown of the Cr 2 O 3 scale for the studied experimental conditions. Finally, the modeling approach was extended to consider time-dependent oxidation and volatilization rate constants to develop a more appropriate lifetime criterion for microturbine recuperator foils.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

The Application of Differential Scanning Calorimetry to Investigate Precipitation Behavior in Nickel-Base Superalloys Under Continuous Cooling and Heating Conditions

In this study, a suite of experimental tools and fast-acting, numerical-simulation techniques was used to quantify the precipitation behavior of three nickel-base superalloys: IN-100, LSHR, and 718. Experimental methods comprised differential scanning calorimetry (DSC) to establish the specific heat as a function of temperature and selected direct-resistance heating trials (using a Gleeble ® machine) to obtain samples for microstructural analysis. For the DSC experiments, each alloy was cooled at a prescribed constant rate (between 5 and 20 K/min) after an initial soak/equilibration in the high-temperature, single-phase (supersolvus) temperature regime. On-heating DSC trials beginning at ambient temperature were also performed on alloy 718 in three different starting conditions: super- δ -solvus solution treated and water quenched (denoted as ST), solution treated and aged (STA), and solution treated and overaged (STOA). DSC results, revealing the thermal signatures associated with the kinetics of precipitation of γ ' (IN-100, LSHR) or γ ' and γ " (718), were interpreted using a previously-developed fast-acting routine that treats concurrent nucleation, growth, coarsening, and dissolution. For these simulations, special attention was paid to various thermo-kinetic input parameters including equilibrium solvus-approach curves, bulk free energies of transformation, matrix-precipitate interface energies, and effective diffusivities. For the γ - γ ' superalloys (IN-100 and LSHR), estimates of precipitate volume fraction as a function of temperature from the specific-heat data revealed semi-quantitative agreement with simulation predictions. For the γ - γ '- γ " superalloy (718), simulation predictions of precipitate volume fractions were converted to specific heat as a function of temperature and showed semi-quantitative agreement with the direct measurements.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Heterogeneous photo-Fenton-like degradation of emerging pharmaceutical contaminants in wastewater using Cu-doped MgO nanoparticles

In this study, a facile thermal decomposition method was utilized to synthesize Cu-doped MgO nanoparticles possessing mesoporosity. These mesoporous Cu doped MgO nanoparticles were shown to be efficient photo-Fenton-like catalysts for the degradation of emerging pharmaceutical contaminants in wastewater and were able to completely oxidize salicylic acid within 1 hour under optimized conditions. Tetracycline was shown to be converted to other intermediates with a large portion of it undergoing full mineralization. Batch experiments were conducted to demonstrate the effects of Cu loading on MgO, overall catalyst loading, and H 2 O 2 concentration on the salicylic acid and tetracycline conversion and rate constants. Quenching experiments revealed that both •OH radicals or HO 2 •/•O 2 - radicals were involved in the reaction, with the latter showing a higher contribution. The surface dissolution of MgO was shown to facilitate a high pH environment which completely prevented Cu from leaching out of the catalyst while retaining high activity. The catalyst reusability was shown to be satisfactory with high activity and conversion being preserved over five cycles.

04 OIL SHALES AND TAR SANDS↗
DOE OSTI2020

Synergistic catalysis by Mn promoted ceria for molecular oxygen assisted epoxidation

Mesoporous manganese doped cerium oxide catalysts were prepared by an inverse micelle method with different manganese loadings. These materials exhibited superior activity for epoxidation of alkenes with molecular oxygen. Highest active 10MnCe material showed an activity of 80 % conversion and >99 % selectivity for cyclooctene epoxidation. The fluorite crystal structure which facilitates the high oxygen mobility, low temperature reducibility, homogeneous distribution of manganese on ceria, nanoparticle nature, higher number of oxygen vacancies, low valent states of manganese and cerium, and the ability to generate reactive oxygen species of the manganese doped cerium oxide could be correlated to the high catalytic activity. The reaction followed first order kinetics with a rate constant of 0.31 h –1 at 100 °C, and the activation energy turned out to be 10.5 kJ/mol. In conclusion, the mechanistic study revealed that the reaction proceeds via a unique mechanism which involves in situ generated superoxide and singlet oxygen species..

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Separation of radium and actinium using zirconia

Herein, zirconia was investigated as a radiation-resistant support for radium and actinium aqueous ion separations. Acetate and total metal ion concentrations were experimentally evaluated as factors that could affect retention using La and Ba surrogates. Pseudo-second order rate constants were derived and the uptake of La was determined to be endothermic. Elution profiles containing Ba, La, 228 Ra, 228 Ac, and 212 Pb are presented and discussed.

07 ISOTOPE AND RADIATION SOURCES↗
DOE OSTI2025

Synergistically combining peracetic acid and reduced graphene oxide membranes to degrade trace organic contaminants

The removal of trace organic contaminants is a critical step for the reuse of municipal and industrial wastewater. Herein, we demonstrate a catalytic membrane platform synergistically integrating reduced graphene oxide (rGO) membranes and peracetic acid (PAA) oxidation, using a dye of methylene blue (MB) and a pesticide of 2,4-dichlorophenoxyacetic acid (2,4-D) as model contaminants. In a crossflow system with rGO membrane and 25 ppm PAA, the degradation rates of MB and 2,4-D were 22 and 0.12 g h −1 per g rGO, with an initial concentration of 10 and 1.1 ppm, respectively. The degradation time profile of MB and 2,4-D follows a pseudo-first-order model, and the degradation rate constant increases with increasing initial PAA doses. Here, the rGO membranes also exhibited good stability over a 1-month test for 2,4-D degradation. In addition to the nanofiltration performance of the rGO membrane, the integrated PAA-rGO membrane process shows great potential to degrade various organic contaminants without the need to separate and recover the metal-free catalyst in downstream treatment.

2,4-D↗
DOE OSTI2026

Catalytic resonance theory for the kinetics of photon-promoted catalysis

The illumination of catalytic surfaces with a continuous or pulsed stream of photons dynamically modulates surface chemistry for faster rates, non-equilibrium conversion, or product selectivity control. To establish fundamental principles of dynamic photon-modulated catalysis, the photocatalytic conversion of a generic surface reaction was simulated using the kinetic Monte Carlo method to understand the kinetic implications of an independent stream of photons that promotes surface product desorption. The time-averaged photocatalytic rate at differential conditions for varying photon flux and temperatures indicated three kinetic regimes described by product thermal desorption control, surface reaction control, and an intermediate kinetic regime with a zero slope Arrhenius plot, consistent with a degree of rate control dominated by the photon arrival frequency (i.e., per-site photon flux). Here, the maximum photocatalytic rate occurred orders of magnitude above the Sabatier limit at the resonance frequency, identified as the photon arrival frequency matching the surface reaction rate constant.

Canavan, Jesse R. [University of Minnesota, Minnea↗
DOE OSTI2024

Bioelectrochemical reactor to manage anthropogenic sulfate pollution for freshwater ecosystems: Mathematical modeling and experimental validation

Anthropogenic sulfate loading into otherwise low-sulfate freshwater systems can cause significant ecological consequences as a biogeochemical stressor. To address this challenge, in situ bioremediation technologies have been developed to leverage naturally occurring microorganisms that transform sulfate into sulfide rather than implementing resource-intensive physio-chemical processes. However, bioremediation technologies often require the supply of electron donors to facilitate biological sulfate reduction. Bioelectrochemical systems (BES) can be an alternative approach for supplying molecular hydrogen as an electron donor for sulfate-reducing bacteria through water electrolysis. Although the fundamental mechanisms behind BESs have been studied, limited research has evaluated the design and operational parameters of treatment systems when developing BESs on a scale relevant to environmental systems. Further, this study aimed to develop an application-based mathematical model to evaluate the performance of BESs across a range of reactor configurations and operational modes. The model was based on sulfate transformation by hydrogenotrophic sulfate-reducing bacteria coupled with the recovery of solid iron sulfide species formed by the oxidative dissolution of dissolved ferrous iron from a stainless steel anode. Sulfate removal closely corresponded to the rate of electrolytic hydrogen production and hydraulic residence time but was less sensitive to specific microbial rate constants. The mathematical model results were compared to experimental data from a pilot-scale BES tested with nonacidic mine drainage as a case study. The close agreement between the mathematical model and the pilot-scale BES experiment highlights the efficacy of using a mathematical model as a tool to develop a conceptual design of a scaled-up treatment system.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

An experimental and kinetic modeling study of cyclopentane and dimethyl ether blends

Cyclopentane is a suitable naphthene, or cycloalkane, in a palette for multi-component gasoline surrogate fuels due to its presence in market fuels and its relevance to alkyl substituted cyclopentanes also present. However, the previous oxidation studies of cyclopentane have primarily focused on neat mixtures. Blending cyclopentane with dimethyl ether in this work therefore serves to inform our understanding of, and improve predictive models for, multi-component mixtures. Here, the auto-ignition of cyclopentane/dimethyl ether blends was studied in a high-pressure shock tube and in a rapid compression machine. A wide range of temperatures (650 – 1350 K) and elevated pressures of 20 and 40 bar were studied at equivalence ratios of 0.5, 1.0 and 2.0 in air for two blending ratios (30/70 and 70/30 mole% cyclopentane/di-methyl ether mixtures). A detailed kinetic model for cyclopentane was revised to capture the measured ignition delay times and apparent heat release rates in this study. Literature ignition delay time, jet-stirred reactor, and laminar burning velocity measurements of neat cyclopentane were used as additional validation. Improvements to the kinetic model were based on recent literature studies related to sub-models including cyclopentene and cyclopentadiene which allowed the removal of previous local rate-constant optimizations. Low temperature reactivity of cyclopentane was found to be controlled by the branching ratio between concerted elimination of HO͘ 2 and the strained formation of Q&#775OOH radicals in agreement with previous studies. In this study, the low branching ratio of Q&#775OOH formation increases the influence of a competing consumption pathway for cyclopentyl-peroxy (CPTO͘ 2 J) radicals. The sensitivity of the simulated ignition delay times to the formation of cyclopentyl hydroperoxide (CPTO 2 H), from CPTO͘ 2 J and HO͘ 2 , is discussed. The current model is used to analyze the influence of dimethyl ether on the reactivity of cyclopentane in the context of previous literature studies of dimethyl ether binary blends with ethanol and toluene.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

An experimental and kinetic modeling study of NO x sensitization on methane autoignition and oxidation

An experimental and kinetic modeling study of the influence of NO x (i.e. NO 2 , NO and N 2 O) addition on the ignition behavior of methane/‘air’ mixtures is performed. Ignition delay time measurements are taken in a rapid compression machine (RCM) and in a shock tube (ST) at temperatures and pressures ranging from 900–1500 K and 1.5–3.0 MPa, respectively for equivalence ratios of 0.5–2.0 in ‘air’. The conditions chosen are relevant to spark ignition and homogeneous charge compression ignition engine operating conditions where exhaust gas recirculation can potentially add NO x to the premixed charge. The RCM measurements show that the addition of 200 ppm NO 2 to the stoichiometric CH 4 /oxidizer mixture results in a factor of three increase in reactivity compared to the baseline case without NOx for temperatures in the range 600–1000 K. However, adding up to 1000 ppm N 2 O does not show any appreciable effect on the measurements. The promoting effect of NO 2 was found to increase with temperature in the range 950–1150 K, while the sensitization effect decreases at higher pressures. The experimental results measured are simulated using NUIGMech1.2 comprising an updated NO x sub-chemistry in this work. A kinetic analysis indicates that the competition between the reactions ĊH 3 + NO 2 ↔ CH 3 Ȯ + NO and ĊH 3 + NO 2 (+M) ↔ CH 3 NO 2 (+M), the former being a propagation reaction and the latter being a termination reaction governs NO x sensitization on CH 4 ignition. Recent calculations by Matsugi and Shiina (A. Matsugi, H. Shiina, J. Phys. Chem. A. 121 (2017) 4218–4224) for the nitromethane formation reaction CH 3 + NO 2 (+M) ↔ CH 3 NO 2 (+M), together with the recently calculated rate constants for HONO/HNO 2 reactions significantly improve ignition delay time predictions in the temperature range 600–1000 K. Furthermore, the experiments with NO addition reveal a non-monotonous sensitization impact on CH 4 ignition at lower temperatures with NO initially acting as an inhibitor at low NO concentrations and then as a promoter as NO concentrations increase in the mixture. This non-monotonous trend is attributed to the role of the chain-termination reaction ĊH 3 + NO 2 (+M) ↔ CH 3 NO 2 (+M) and the impact of NO on the transition to the chain-branching steps CH 2 O + HȮ 2 ↔ HĊO + H 2 O 2 , H 2 O 2 (+M) ↔ ȮH + ȮH (+M), HĊO ↔ CO + Ḣ followed by CO + O 2 ↔ CO 2 + Ö and Ḣ + O 2 ↔ Ö + ȮH. NUIGMech1.2 is systematically validated against the new ignition delay measurements taken here together with species measurements and high temperature ignition delay time data available in the literature for CH 4 /oxidizer mixtures diluted with NO 2 /N 2 O/NO and is observed to accurately capture the sensitization trends.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

An experimental and modeling study on auto-ignition kinetics of ammonia/methanol mixtures at intermediate temperature and high pressure

A rapid compression machine (RCM) has been applied to measure the ignition delay times of NH 3 /CH 3 OH mixtures covering pressures of 20 and 40 bar, equivalence ratios of 0.5, 1.0 and 2.0, and temperatures between 845 and 1100 K. Here the measurements show that the NH 3 /CH 3 OH mixtures become more reactive with increasing methanol addition. Addition of merely 1% (molar basis) of CH 3 OH to NH 3 lowers the ignition temperature around 100 K at 40 bar in comparison to pure NH 3 . The ignition delay is a complex function of fuel mixture and stoichiometry. For the 1% CH 3 OH mixture, the leaner mixtures are more reactive, while the reverse trend is found for mixtures with 5%, 20% and pure CH 3 OH. Analysis of the pressure profiles shows three distinct ignition modes for NH 3/ CH 3 OH mixtures, facilitated by the pre-ignition heat release from NH 3 consumption. A detailed mechanism for ignition of NH 3 /CH 3 OH fuel blends has been developed, capable of reproducing the ignition behavior of mixtures with reasonable accuracy. A subset for amine / methanol interactions was established, with rate constants for the key reaction between NH 2 and CH 3 OH calculated from ab initio theory. A sensitivity analysis indicates that the critical reactions during the auto-ignition process vary with the CH 3 OH mole fraction in the fuel. The ammonia chemistry, namely NH 2 + NO, NH2 + NO 2 and NH 2 + HO 2 , is dominant for the mixture with 1% CH 3 OH, while the reactions related to CH 3 OH and H 2 O 2 are more important for the 20% CH 3 OH mixture. The interaction between ammonia and methanol shows a more prominent effect on auto-ignition for mixtures with 5% CH 3 OH in fuel as compared to those with 1% and 20% CH 3 OH. According to the modeling results, methanol addition is found to enrich the O/H radical pool, consuming ammonia and promoting auto-ignition through different reaction pathways.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

The role of energy transfer and competing bimolecular reactions in characterizing the unimolecular dissociations of allylic radicals

Resonantly stabilized radicals (RSR's) such as allylic radicals typically have bond energies exceeding 45 kcal/mol and are therefore reasonably long-lived up to quite high temperatures. Consequently, kinetics of the unimolecular dissociations and bimolecular reactions of these long-lived RSR's assume significance in high temperature chemically reacting systems such as in flames. Our recent analyses (J. Cho et al., Proc. Comb. Inst., 2022) of the uncertainty propagated by the energy transfer parameters for 1-methylallyl (1MA) dissociation to the laminar flame speed, indicates an intricate coupling between the kinetics of 1MA dissociation (chain propagation) and its reaction with H-atoms (chain-termination). Here, this work extends such analyses to other C 3 – C 5 allylic radicals: allyl, 2-methylallyl, 1,1-dimethylallyl, 1,2-dimethylallyl, and 1,3-dimethylallyl. Theoretical kinetics for the C 3 – C 4 allylic radicals were taken from prior literature studies (J.A. Miller et al., J. Phys. Chem., 2008; J. Cho et al., Proc. Comb. Inst., 2022; R.S. Tranter et al., Proc. Comb. Inst., 2017). Potential energy surfaces were newly computed for the dissociations of the larger C5 allylic radicals and the reactions of these radicals with H-atoms. These PES's were then used to calculate rate constants for the relevant unimolecular and bimolecular reactions. Energy transfer has a crucial role to play in these pressure-dependent reactions and therefore the present kinetics calculations relied on a-priori predictions of collisional energy transfer parameters to best characterize the branching between chain propagating unimolecular dissociations of these allylic radicals and chain terminating bimolecular reactions of these RSR's with H-atoms. Prompt dissociations are now established to be a universal feature of free radical dissociations. Here we have also characterized the propensity for prompt dissociations in these more-stable allylic RSR's and their role in combustion simulations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Kinetic model-based group contribution method for derived cetane number prediction of oxygenated fuel components and blends

A four-step autoignition model was used to derive an expression for the ignition delay (ID) measured in ignition quality testers (IQT) with the derived cetane number (DCN) determined from this ID using the ASTM D6890 standard correlation. The model predicts DCN for individual compounds and blends as a function of each compound's global initiation and net chain branching rate constants. Expressions for these values were determined assuming they could be related to the functional groups present in each compound. Measurement data for 125 compounds and 94 binary and ternary blends (including oxygenates: alcohols, aldehydes, esters, ethers, and ketones), from literature and from measurements performed in our lab, were used to obtain the dependence of the measured ignition delay on each functional group. The new kinetic model-based group contribution method was able to predict the ignition delay of both pure compounds and blends, with an average DCN error of 4.4 (19%) and 2.8 (11%), respectively. Here, the blend model was also used to develop an ID mixing rule by incorporating existing IQT ignition delay data for each compound. Use of the mixing rule gave an average DCN error of 3.6 (16%) for blends. Both the blend model and mixing rule were found to be superior compared to standard linear by volume fraction or mole fraction mixing rules commonly used to estimate the DCN of mixtures.

42 ENGINEERING↗
DOE OSTI2024

An experimental, theoretical and kinetic modeling study of the N 2 O-H 2 system: Implications for N 2 O + H

The reaction of N 2 O with His the key step in consumption of nitrous oxide in thermal processes. The major product channel is N 2 + OH, while NH + NO constitute minor products. In addition, a pathway involving HNNO, initiated by N 2 O + H (+M)$\rightleftarrows$HNNO (+M) (R3, R4), has been inferred from experiment and theory by Burke and coworkers. At longer reaction times, the reaction may reach partial equilibration, and in addition to k 3 and k 4 the importance of this channel depends on the thermodynamic properties of HNNO and its consumption reactions, mainly HNNO + H. In the present work, we re-examined the thermochemistry of HNNO and calculated rate constants and branching fractions for the HNNO + H reaction. Experiments on the N 2 O-H 2 system were conducted in a high-pressure flow reactor at 100 atm as a function of temperature (600-925 K) and stoichiometry and explained in terms of an updated chemical kinetic model. The results support the importance of the HNNO pathway, which results in inhibition of N 2 O consumption and formation of NH 3 . In addition, selected literature results on the N 2 O-H 2 system are re-examined and the implications for the other product channels of N 2 O + H, in particular NH + NO, are discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Quantifying the effects of artificial aging on the ignition and self-propagating reactions of Ni(V)/Al multilayers

Bimetallic, reactive multilayers are uniformly structured materials composed of alternating nanoscale layers that may be ignited to produce self-propagating intermetallic-formation reactions. When reactive multilayers age, there is a change in local composition and loss of stored chemical energy due to mass transport and rearrangement at the interfaces. Here, to quantify the long-term reliability of commercial Ni(V)/Al multilayers, the effects of accelerated aging on both ignition sensitivity and self-propagating reactions have been examined. Thermally aged samples were characterized using transmission electron microscopy, differential scanning calorimetry, and laser ignition combined with high-speed videography. The analytically quantifiable nature of both continuous wave laser ignition and reactive wave propagation enabled calculations of Arrhenius rate constants for as-received and various heat-treated multilayers. With heat treatment, there is a change in the intermixed thickness and interfacial chemistry that decreases the activation energy for point ignition but increases it for self-propagating reactions. This finding implies that with increased thermal aging, the reaction becomes easier to facilitate in the solid state but harder in the liquid phase.

Energetic material↗
DOE OSTI2021

Uranium hydride corrosion. I New insights into the Condon-Kirkpatrick model of uranium hydride formation rate

An analytic solution to the uranium hydride formation rate equation of Condon and Kirkpatrick (CK) has been developed, which is directly solved via algebraic operations and requires only gaseous hydrogen (H 2 ) pressure and temperature as inputs. The solution does not depend on the specific functional forms of the hydriding and dehydriding rate constants, nor of key physical parameters. Furthermore, a modified form of the CK model has also been developed, where replacement of the hydrogen solubility function results in an improved fit to published experimental data as H 2 pressure decreases toward the corrosion threshold value.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Evidence of an oxidation induced phase transformation for a delta phase plutonium-gallium alloy

The oxidation of an ~1.5 at% Ga plutonium metal alloy in dry air as a function of time was studied using a combination of FIB-SEM, AES, and XRD. Analysis of SEM images of FIB cross-sections of the oxide allowed for direct measurement of the oxide thickness as well as determination of heterogeneity in the extent of the oxide. AES analysis performed on cross-sections of the oxide allowed for quantitative analysis of the atomic composition and semi-quantitative analysis of the chemical composition. Initial preparation of the sample was found to induce a martensitic transformation to α' - Pu with an average thickness of 233 nm. Electropolishing was found to be sufficient to fully remove the α' layer with creation of only a minimum oxide layer. Growth of the oxide in dry air was found to initially follow parabolic kinetics, with a parabolic rate constant orders of magnitude higher than expected for δ-Pu but in-line with values extrapolated to room temperature for α-Pu. Following complete oxidation of the initial α` layer, further regions of plutonium metal depleted in gallium were observed to form at the oxide / metal interface. However, gallium, as Ga 2 O 3 , was found to be enriched at the surface and present in the oxide in an amount comparable to the relative Ga:Pu ratio of the bulk metal alloy. Finally, the results presented here serve to bridge a diverse array of previous experimental and theoretical data and provide the first comprehensive view of the fate of the δ-stabilizer during formation of an oxide.

36 MATERIALS SCIENCE↗